SF61R THRU SF67R VOLTAGE 50V ~ 600V 6.0AMP Super Fast Rectifiers Elektronische Bauelemente RoHS Compliant Product A suffix of "-C" specifies halogen-free R-6 FEATURES .360(9.1) .340(8.6) DIA. * Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application 1.0(25.4) MIN. .360(9.1) .340(8.6) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guaranteed * Polarity: Color band denotes cathode end * Mounting position: Any 1.0(25.4) MIN. .052(1.3) .048(1.2) DIA. * Weight: 1.10 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER SF61R Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current 50 35 50 SF62R SF63R SF64R SF65R SF66R SF67R UNITS 100 70 100 150 105 150 .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 6.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG 200 140 200 300 210 300 400 280 400 600 420 600 A 6.0 150 1.25 0.95 5.0 V V V 1.50 A V µA 50 35 µA 50 -65 +150 pF C nS NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. http://www.SeCoSGmbH.com 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 1 of 2 SF61R THRU SF67R VOLTAGE 50V ~ 600V 6.0AMP Super Fast Rectifiers Elektronische Bauelemente RATING AND CHARACTERISTIC CURVES (SF61R THRU SF67R) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC trr 10W NONINDUCTIVE ( ) D.U.T. 25Vdc (approx.) | | | | | | | | +0.5A (+) PULSE GENERATOR (NOTE 2) ( ) AVERAGE FORWARD CURRENT,(A) 50W NONINDUCTIVE 0 -0.25A (+) 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) -1.0A NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 1cm 2. Rise Time= 10ns max., Source Impedance= 50 ohms. 6 5 4 Single Phase 3 Half Wave 60Hz Resistive Or Inductive Load 2 0.375"(9.5mm) Lead Length 1 0 SET TIME BASE FOR 0 25 50 FIG.4-TYPICAL REVERSE CHARACTERISTICS CHARACTERISTICS 50 10 10 REVERSE LEAKAGE CURRENT, (mA) 50 64R F6 6R ~SF SF 67 R ~S 65R SF6 1R 1.0 SF INSTANTANEOUS FORWARD CURRENT,(A) FIG.3-TYPICAL FORWARD 3.0 Tj=25 C Pulse Width 300us 1% Duty Cycle 0.1 .01 .4 .6 .8 1.0 1.2 1.4 1.6 100 125 150 175 3.0 1.0 Tj=100 C Tj=25 C 0.1 .01 1.8 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FORWARD VOLTAGE,(V) FIG.6-TYPICAL JUNCTION CAPACITANCE FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 150 JUNCTION CAPACITANCE,(pF) PEAK FORWARD SURGE CURRENT,(A) 75 AMBIENT TEMPERATURE,( C) 50 / 10ns / cm 120 90 Tj=25 C 8.3ms Single Half Sine Wave 60 JEDEC method 30 150 125 100 75 50 25 0 0 1 5 10 NUMBER OF CYCLES AT 60Hz http://www.SeCoSGmbH.com 01-Jun-2002 Rev. A 50 100 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) Any changing of specification will not be informed individual Page 2 of 2