SMF10SS THRU SMF15SS VOLTAGE 1000V ~ 1500V Elektronische Bauelemente 1.0AMP Surface Mount Fast Recovery Rectifiers RoHS Compliant Product A suffix of "-C" specifies halogen-free 2010 .181(4.60) FEATURES .173(4.40) * Ideal for surface mount applications * High Voltage, Low profile package * Built-in strain relief * Fast switching speed .002(0.05) ) 50 (0. 20 .0 R0 0.091(2.30) 0.083(2.10) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 0.063 grams 0.049(1.25) 0.049(1.25) 0.033(0.85) 0.033(0.85) 0.049(1.25) 0.033(0.85) * Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ , TSTG SFM10SS SFM12SS SFM15SS UNITS 1000 800 1200 1500 V 960 1200 V 1000 1200 1500 V 1.0 A 25 A 1.3 V 5.0 100 µA µA 500 15 -55 +155 nS pF C NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.Marking Code: SMF10SS RGC10M SMF12SS RGC10Q SMF15SS RGC10Y http://www.SeCoSGmbH.com 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 1 of 2 SMF10SS THRU SMF15SS VOLTAGE 1000V ~ 1500V Elektronische Bauelemente 1.0AMP Surface Mount Fast Recovery Rectifiers RATING AND CHARACTERISTIC CURVES (SMF10SS THRU SMF15SS) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) CHARACTERISTICS 10 3.0 1.0 1.2 1.0 0.8 Single Phase 0.6 Half Wave 60Hz Resistive Or Inductive Load 0.4 0.2 0 0 20 40 Tj=25 C 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE ( C) Pulse Width 300us 1% Duty Cycle 0.1 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) PEAK FORWAARD SURGE CURRENT,(A) INSTANTANEOUS FORWARD CURRENT,(A) 50 50 40 30 Sine Wave JEDEC method 10 0 1 5 (+) 1W NONINDUCTIVE 2. Rise Time= 10ns max., Source Impedance= 50 ohms. 0 35 JUNCTION CAPACITANCE,(pF) | | | | | | | | -0.25A 100 FIG.5-TYPICAL JUNCTION CAPACITANCE NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. +0.5A 50 10 NUMBER OF CYCLES AT 60Hz OSCILLISCOPE (NOTE 1) trr 8.3ms Single Half Tj=25 C 20 30 25 20 15 10 5 0 -1.0A 1cm SET TIME BASE FOR .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) 50 / 10ns / cm http://www.SeCoSGmbH.com 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 2 of 2