SMF112A THRU SMF115A VOLTAGE 1200V ~ 1500V Elektronische Bauelemente 1.0AMP Surface Mount Fast Recovery Rectifiers RoHS Compliant Product A suffix of "-C" specifies halogen-free SMA FEATURES * Ideal for surface mount applications * High Voltage * Built-in strain relief * Fast switching speed Dimensions in MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 0.063 grams C A B H D E G F Dimensions in Millimeters Inches A 1.25 1.65 0.049 0.065 B 3.99 4.60 0.157 0.181 C 2.50 2.90 0.098 0.114 D 1.98 2.44 0.078 0.096 E 0.051 0.203 0.002 0.008 F G 4.78 5.28 0.188 0.208 0.76 1.52 0.030 0.060 H 0.152 0.305 0.006 0.012 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current SMF115A SMF112A 1500 1050 1500 1200 840 1200 UNITS V V V .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave 1.0 A superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current Ta=25 C 30 1.3 5.0 A V µA at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG 100 µA 350 15 -65 +175 nS pF C NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. http://www.SeCoSGmbH.com 01-Jun-2006 Rev. B Any changing of specification will not be informed individual Page 1 of 2 SMF112A THRU SMF115A VOLTAGE 1200V ~ 1500V Elektronische Bauelemente 1.0AMP Surface Mount Fast Recovery Rectifiers RATING AND CHARACTERISTIC CURVES (SMF112A THRU SMF115A) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) CHARACTERISTICS 10 3.0 1.0 1.2 1.0 0.8 Single Phase 0.6 Half Wave 60Hz Resistive Or Inductive Load 0.4 0.2 0 0 20 40 Tj=25 C 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE ( C) Pulse Width 300us 1% Duty Cycle 0.1 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) PEAK FORWAARD SURGE CURRENT,(A) INSTANTANEOUS FORWARD CURRENT,(A) 50 50 40 30 Sine Wave JEDEC method 10 0 1 5 (+) 1W NONINDUCTIVE 2. Rise Time= 10ns max., Source Impedance= 50 ohms. 0 35 JUNCTION CAPACITANCE,(pF) | | | | | | | | -0.25A 100 FIG.5-TYPICAL JUNCTION CAPACITANCE NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. +0.5A 50 10 NUMBER OF CYCLES AT 60Hz OSCILLISCOPE (NOTE 1) trr 8.3ms Single Half Tj=25 C 20 30 25 20 15 10 5 0 -1.0A 1cm SET TIME BASE FOR .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) 50 / 10ns / cm http://www.SeCoSGmbH.com 01-Jun-2006 Rev. B Any changing of specification will not be informed individual Page 2 of 2