SC9696P CD SERVO CONTROLLER WITH MCU DESCRIPTIONS SC9696P is a CD play controller with CD player, remote control decoding, clock display mature function , which includes CD digital servo controller, CD signal processor, digital audio DAC output, with interface supporting wma/mps encoding/decoding circuit, TunePLL circuit SC9257, electronic volume control circuit, LCD drive circuit SC2124 and compatible with TAPE and AUX IN. FEATURES LQFP-80-10x10-0.4 * CD play Compatible with CD/CD-R/CD-RW Support CD play/pulse Support CD Pre/Next Support CD FF/FB Support single music playback/catalog circle play & display Support CD random access & display Support browse play ORDERING INFORMATION Device Package SC9696P LQFP-80-10x10-0.4 Seal SC9696P Support CD sync tape recording * Receiving Support bands select in four areas (USA, GEN 1/2, JAPAN) Support manually channel tuning forward/backward APPLICATIONS * Desktop audio system Support automatically channel tuning forward/backward Support channel preset (FM: 20, AM/MW:10) * Taping Support TAPE display * AUX Support AUX input * Electronic volume control Support CD/receiving/tape/AUX voice channel electronic switching Support volume adjust & display Support voice mode FLAT, POP, CLASS, ROCK, JAZZ5 preset Support mute switch control & display Support X-BASS switch control & f\display Support ENCODER-VOLUME control * Clock Support Clock display & adjust Support alarm, alarm turn on/off Support sleep mode HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 1 of 21 SC9696P BLOCK DIAGRAM ABSOLUTE MAXIMUM RATING (Tamb=25°C) Characteristics Symbol Rating Unit Supply Voltage VDD -0.5 ~ +5.5 V Input Voltage on Pins VIN -0.5 ~VDD + 0.5 V Operating Temperature Topr -20 ~ +75 °C ELECTRICAL CHARACTERISTICS(VDD=4.5~5.5V; VSS=0V; Tamb=-10~+50°C) Characteristics Symbol MCU Operating Voltage MVDD Typ. Max. Unit - Test condition Min. 4.0 5.0 5.5 V Operating Voltage VDD Exception MCU 4.5 5.0 5.5 V Operating Current IDD 5V(CD operating) - 50 - mA RFIN Input Signal VRFIN - - 1 - V Reference Voltage VIr - - 0.5VDD - Vcom - - 2.5 - V IDB - 0 - 9 μA IDA - 0 - 9 μA Photoelectricity Signal Bias Input Input Current Of Central Diode B Input Current Of Central Diode A HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 2 of 21 SC9696P Characteristics Input Current Of Central Diode C Input Current Of Central Diode D Input Current Of Satellite Diode F Input Current Of Satellite Diode E Low-level Output Current at PA Port. High-level Output Current at PA Port. Low-level Output Current at PB Port. High-level Output Current at PB Port. Low-level Output Current at PC Port. High-level Output Current at PC Port. Low-level Output Current at PG Port. High-level Output Current at PG Port. Low-level Output Current at PH Port. High-level Output Current at PH Port. LDON Low-level Output Current Load Resistance DAC Full-Scale DAC Output Voltage Symbol Test condition Typ. Max. Unit IDC - 0 - 9 μA IDD - 0 - 9 μA IRF - 0 - 4.5 uA IRE - 0 - 4.5 μA IOL(A) - - 10 - mA IOH(A) - - 5 - mA IOL(B) - - 10 - mA IOH(B) - - 5 - mA IOL(C) - - 10 - mA IOH(C) - - 5 - mA IOL(G) - - 10 - mA IOH(G) - - 5 - mA IOL(H) - - 10 - mA IOH(H) - - 5 - mA ILDON - 0 - 2 mA 5 - - KΩ 0.9 1.1 1.2 V 0 1 - mA 0 1 - mA 0 1 - mA 0 5 10 mA RL VFS RAD Output Current IRAD FOC Output Current IFOC SLED Current ISLED MOTO Output Current IMOTO Left channel is the same as the right. Left channel is the same as the right. High level is the same as the low level. High level is the same as the low level. High level is the same as the low level. High level is the same as the low level. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn Min. REV:1.1 2009.02.26 Page 3 of 21 SC9696P Characteristics Low Level Output Driving Voltage High Level Output Driving Voltage Moto Low Level Output Voltage Moto High Level Output Voltage Driving Current of high impedance DAC Total Harmonic Distortion DAC output Signal to Noise DA Filter Attenuation OSC Frequency Symbol Test condition VOLDRIVE1 RAD, FOC, SELD VOHDRIVE1 VOLmoto RAD, FOC, SELD - RAD, FOC, SELD, MOTO Max. Unit - 0.4 V - VDD V - 1.0 V - VDD V -10 0 +10 μA 0 VDD-0.4 0 THD 0dB 1Khz Signal Input - -65 - dB S/N No signal input - 90 100 dB 0 to 19 KHz - - 0.001 dB 19 to 20 KHz 1 - 2 dB 24KHz 25 - - dB 25 to 35 KHz 40 - - dB 35 to 64 KHz 50 - - dB 64 to 68 KHz 31 - - dB 68KHz 35 - - dB 69 to 88KHz 40 - - dB - MHz Filter_DA Fsystem HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn Typ. VDD-1 VOHmoto IZODRIVE Min. - 16.9344 REV:1.1 2009.02.26 Page 4 of 21 SC9696P PIN CONFIGURATIONS 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 PG.3 1 60 OV_RAM PG.2 2 59 WCLKIN PG.1 3 58 SCLKIN PG.0 4 57 SDATAIN MGND 5 56 WCLKOUT MVDD 6 55 SCLKOUT BUZZ/PB.7 7 54 SDATAOUT INT6/PB.6 8 53 SBSY INT5/PB.5 9 52 GND SC9696P EXTREF/PA.7 10 51 VDD AD6/PA.6 11 50 MOTO AD5/PA.5 12 49 SLED AD4/PA.4 13 48 FOC AD3/PA.3 14 47 RAD AD2/PA.2 15 46 Sysclk AD1/PA.1 16 45 VOL AD0/PA.0 17 44 FILTCL MVDD 18 43 FILTCR MXI 19 42 VOR MXO 20 41 VREF 21 22 23 24 25 26 27 28 29 30 31 32 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn 33 34 35 36 37 38 39 40 REV:1.1 2009.02.26 Page 5 of 21 SC9696P PIN DESCRIPTIONS Pin no. Pin name I/O Descriptions General purpose IO port, input bit by bit control with pull-up, 1 PG.3 I/O 2 PG.2 I/O 3 PG.1 I/O 4 PG.0 I/O 5 MGND I MCU and periphery ground 6 MVDD I MCU and periphery power supply 7 BUZZ/PB.7 I/O 8 INT6/PB.6 I/O 9 INT5/PB.5 I/O 10 EXTREF/PA.7 I/O 11 AD6/PA.6 I/O 12 AD5/PA.5 I/O 13 AD4/PA.4 I/O 14 AD3/PA.3 I/O 15 AD2/PA.2 I/O 16 AD1/PA.1 I/O 17 AD0/PA.0 I/O 18 MVDD I MCU and periphery power supply 19 MXI I 75K oscillator input port 20 MXO O 75K oscillator output port 21 MGND I MCU and periphery ground 22 INT4/PB.4 I/O 23 INT3/PB.3 I/O output pull-up close General purpose IO port, input bit by bit control with pull-up, output pull-up close General purpose IO port, input bit by bit control with pull-up, output pull-up close General purpose IO port, open-drain input bit by bit control with pull-up, output forced to pull-up General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input General purpose IO port Also used as AD reference voltage input General purpose IO port Also used as AD switch channel 6 General purpose IO port Also used as AD switch channel 5 General purpose IO port Also used as AD switch channel 4 General purpose IO port Also used as AD switch channel 3 General purpose IO port Also used as AD switch channel 2 General purpose IO port Also used as AD switch channel 1 General purpose IO port Also used as AD switch channel 0 General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 6 of 21 SC9696P Pin no. Pin name I/O Descriptions General purpose IO port, input bit by bit control with pull-up, 24 INT2/PB.2 I/O 25 INT1/PB.1 I/O 26 INT0/PB.0 I/O 27 RXD/PC.7 I/O 28 TXD/PC.6 I/O 29 PC.5 I/O 30 PC.4 I/O 31 PC.3 I/O 32 PC.2 I/O 33 PC.1 I/O 34 PC.0 I/O 35 MRST I MCU reset 36 MTEST I MCU test port, connected to ground when normal working OTP high voltage download output pull-up close, Schmitt input General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input General purpose IO port, input bit by bit control with pull-up, output pull-up close, Schmitt input General purpose IO port, input bit by bit control with pull-up, output pull-up close and also used as serial data receiving. General purpose IO port, input bit by bit control with pull-up, output pull-up close and also used as serial data transmitting. General purpose IO port, input bit by bit control with pull-up, output pull-up close General purpose IO port, input bit by bit control with pull-up, output pull-up close General purpose IO port, open-drain, input bit by bit control with pull-up, output forced to pull-up General purpose IO port, open-drain, input bit by bit control with pull-up, output forced to pull-up General purpose IO port, open-drain, input bit by bit control with pull-up, output forced to pull-up General purpose IO port, open-drain, input bit by bit control with pull-up, output forced to pull-up 37 VPP I 38 PH.7 I/O 39 VDDO I DAC analog power supply 40 VSSO I DAC analog ground 41 VREF O DAC reference voltage output 42 VOR O DAC right channel output 43 FILTCR O DAC right channel filter capacitor. 44 FILTCL O DAC left channel filter capacitor. 45 VOL O DAC left channel output 46 Sysclk I DAC system clock input 47 RAD O Tracking drive output 48 FOC O Focus drive output 49 SLED O Sled drive output 50 MOTO O Spindle drive output 51 VDD I Core digital voltage 52 GND I Core digital ground Common IO port without pull-up or pull-down resistor 53 SBSY O Sub code sync output signal 54 SDATAOUT O Audio data output HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 7 of 21 SC9696P Pin no. Pin name I/O Descriptions 55 SCLKOUT O Data bit clock output 56 WCLKOUT O Data word clock output 57 SDATAIN I Audio data input 58 SCLKIN I Data bit clock input 59 WCLKIN I Data word clock input 60 OV_RAM O Internal SRAM overflow signal 61 V2/SLED_SW I Sledge motor position monitor signal input 62 LDON O Laser control signal output 63 CL16 O 16M clock output 64 VSSA1 I Ground 65 VDDA1 I Power supply 66 B I Central diode current signal input 1 67 A I Central diode current signal input 2 68 C I Central diode current signal input 3 69 D I Central diode current signal input 4 70 F I Satellite diode current signal input 1 71 E I Satellite diode current signal input 2 72 VCOM I Photoelectricity Signal Bias Input 73 Idata O Data Slice feed-back current output 74 RFIN I Reference Signal. 75 RFREF O 76 VSSA2 I Ground 77 VDDA2 I Power supply 78 CRIN I 8M oscillator input 79 CROUT O 8M oscillator output 80 PG.4 I/O Reference Signal reference voltage/level adjustment reference current output General purpose IO port, input bit by bit control with pull-up, output pull-up close HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 8 of 21 SC9696P FUNCTION DESCRIPTIONS 1. LCD SC2124 is adopted for LCD drive circuit. LCD with 4COM×32SEG, 3V, 1/4duty and 1/3 bias is adopted, as shown below: Truth table: COM0 COM1 SEG0 1F 1H 1G SEG1 1A 1J 1P SEG2 1K 1M 1N 1D SEG3 CD 1B 1C \ SEG4 2F 2H 2G 2E SEG5 2A 2J 2P USB SEG6 2K 2M 2N 2D SEG7 MP3 2B 2C WMA SEG8 3F 3H 3G 3E SEG9 3A 3J 3P ID3 SEG10 3K 3M 3N 3D 3B 3C SEG11 COM2 COM3 1E SEG12 4F 4H 4G 4E SEG13 4A 4J 4P FOLDER SEG14 4K 4M 4N 4D SEG15 REPEAT 4B 4C ALL SEG16 5F 5H 5G 5E SEG17 5A 5J 5P MEMORY SEG18 5K 5M 5N 5D SEG19 STEREO 5B 5C RANDOM SEG20 6F 6H 6G 6E SEG21 6A 6J 6P SLEEP SEG22 6K 6M 6N 6D SEG23 TIMER 6B 6C TAPE SEG24 7F 7H 7G 7E SEG25 7A 7J 7P AUX SEG26 7K 7M 7N 7D SEG27 : 7B 7C INTRO SEG28 8F 8H 8G 8E SEG29 8A 8J 8P .MHZ SEG30 8K 8M 8N 8D SEG31 MUTE 8B 8C KHZ HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 9 of 21 SC9696P 2. Jumper A/D Value 3. Pickup Mechanism Clock & Timer 0.00~0.63V SONY KSS-213C Enable 0.63~1.25V SONY KSS-213C Disable 1.25~1.88V THOMSON TCP-11TK Enable 1.88~2.50V THOMSON TCP-11TK Disable 2.50~3.12V SANYO DA11 Enable 3.12~3.75V SANYO DA11 Disable 3.75~4.38V SAMSUNG V75 Disable 4.38~5.00V SAMSUNG V75 Enable Keyboard 3.1 Panel keyboard arrangement KEY0 KEY1 KEY2 KEY3 POWER STOP/BAND FUN_CDUSBSD SLEEP OPCL PLAY FUN_MODE ID3 VOL UP NEXT_FF VOL DN PREV_FW MEMORY MUTE FOLDER_UP(PRESET_UP) REC/COPY INTRO EQ/ X-BASS FOLDER_DN(PRESET_DN) RPT RANDOM TIMER 3.2 Remote keyboard arrangement T0 T1 T2 K0 POWER MUTE OPCL K1 FUN_MODE STOP/BAND FUN_CDUSBSD EQ/ X-BASS REC/COPY K2 T3 NEXT_FF K3 VOL UP PLAY FOLDER_UP(PRESET_UP) K4 VOL DN PREV_FW FOLDER_DN(PRESET_DN) K5 MEMORY K6 INTRO K7 TIMER RANDOM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn RPT ID3 SLEEP REV:1.1 2009.02.26 Page 10 of 21 SC9696P 4. Receiving interface mode 4.1 Receiving band & area Interface for connecting SC9257 (SC72131) 9257_PERIOD/9257_CLOCK/9257_DATA AREA CODE USA 00 GEN1 01 GEN2 JAPAN 10 11 BAND FREQUENCY RANCE[Hz] FREQ STEP[Hz] IF REF[Hz] FM 87.50- 108.00M 50K 50K/3.125K MW 522-1620K 9K 9K +450K 25K -10.7M +450K FM 76.0-90.0M,TV1-3 100K,1CH AM 522-1629K 9K 9K FM 87.50-108.00M 50K 50K/3.15K MW 522-1620K 9K 9K LW 144-281K 1K 1K FM 87.5-108.0M 100K 50K/3.125K AM 520-1710K 10K 10K +10.7M/1.3375M +10.7M/1.3375M +450K +10.7M/1.3375M +450K 4.2 Keys description 1) Enter TUNER mode Press POWER to turn on and press FUN_MODE to enter TUNER mode 2) STOP/BAND Switch band: FM AM FM 3) PREV_REW Press for a short time for manually channel tuning backward Press for longer time for automatically channel tuning backward and stop after tuning. 4) NEXT_FF Press for a short time for manually channel tuning forward Press for longer time for automatically channel tuning forward and stop after tuning. 5) PRESET_UP/PRESET_DN Select preset channel or channel number (cyclic up/down) 6) MEMORY Press MEMORY for a long time to enter channel setting mode for preset channels HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 11 of 21 SC9696P 5. Receiving display 1) FM BAND 2) AM BAND 3) Display of select preset channel 4) Display after 0.5s HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 12 of 21 SC9696P 5) Display of channel memory 6. Tape mode 6.1 Key description 1) Enter TAPE mode Press POWER to turn on and press FUN_MODE to enter TUNER mode. 2) Display 7. CD mode 7.1 Key description 1) Enter CD PLAYER mode Press POWER to turn on and press FUN_MODE to enter CD/USB/SD mode, then press FUN_CDUSBSD to enter CD PLAYER mode. 2) PLAY/PAUSE Play/pause key 3) STOP Stop key HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 13 of 21 SC9696P 4) RANDOM Random access (PREV_REW is invalid in this mode) 5) PREV_REW Press for a short time for previous music and for the last music if the current music is the first one. Press for a long time for fast backward and release for stop, and for normal play if it comes to the beginning. 6) NEXT_FF Press for a short time for next music and for the first music if the current music is the last one. Press for a long time for fast forward and release for stop, and for normal play if it comes to the last. 7) REPEAT 8) MEMORY Enter edit mode (valid in STOP mode) Press REW/FF to select music and press MEMORY to save and up to 20 music can be stored. Then press PLAY to play and it will exit this mode if there is no operation in 10s, with music reversed. Press STOP to clear music and exit this mode. 9) INTRO Browse play switch (10s before play) 7.2 CD display 1) Display number of music and total time in STOP mode 2) Display in PLAY mode HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 14 of 21 SC9696P 3) Display in PAUSE mode Glinting for 0.5s SD 4) Display in REW/FF mode 5) Display in RANDOM mode 6) Display in REPEAT ONE HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 15 of 21 SC9696P 7) Display in REPEAT ALL 8) Display in PROGRAMMING DISPLAY mode 9) Display in PROGRAMMING mode 8. Volume mode 8.1 Key description 1) VOLUME+/Increase/decrease volume 2) MUTE Mute on/off HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 16 of 21 SC9696P 3) EQ Preset voice mode switch FLAT JAZZ CLASSIC POP ROCK FLAT 8.2 Volume and sound effect display 8.3 JAZZ sound effect selected by EQ 9. Others 9.1 Key description 1) CLOCK Press MEMORY (CLOCK ADJ) for a long time in standby mode to enter time setting mode and press UP/DOWN to adjust. 2) SLEEP Press SLEEP to enter the mode and SLEEP glints, press it again for time setting (10~90 min) and SLEEP normally displays. Press it third time to cancel. 3) TIMER Timing turn on (alarm) Press TIMER to enter timing mode and press MEMORY for a long time for time setting and adjust time trough NEXT_FF/PREC_REW 4) POWER Standby and turn on. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 17 of 21 SC9696P 9.2 Display 1) Standby 2) SLEEP 3) TIMER HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 18 of 21 SC9696P TYPICAL APPLICATION DIAGRAM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 19 of 21 SC9696P PACKAGE OUTLINE LQFP-80-10×10-0.4 UNIT: mm 12.00±0.25 10.00±0.25 1.60MAX 0.15±0.05 12.00±0.25 10.00±0.25 0.05~0.20 80 0.25 0.40TYP 0.14~0.25 0.60±0.15 1 MOS DEVICES OPERATE NOTES: Electrostatic charges may exist in many things. Please take following preventive measures to prevent effectively the MOS electric circuit as a result of the damage which is caused by discharge: z The operator must put on wrist strap which should be earthed to against electrostatic. z Equipment cases should be earthed. z All tools used during assembly, including soldering tools and solder baths, must be earthed. z MOS devices should be packed in antistatic/conductive containers for transportation. Disclaimer: • Silan reserves the right to make changes to the information herein for the improvement of the design and performance without further notice! • All semiconductor products malfunction or fail with some probability under special conditions. When using Silan products in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety standards strictly and take essential measures to avoid situations in which a malfunction or failure of such Silan products could cause loss of body injury or damage to property. • Silan will supply the best possible product for customers! HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2009.02.26 Page 20 of 21