SMSC LAN9221I

LAN9221/LAN9221i
High-Performance 16-bit Non-PCI
10/100 Ethernet Controller with
Variable Voltage I/O
PRODUCT FEATURES
Datasheet
Highlights
„
„
„
„
„
„
„
„
Optimized for high performance applications
Efficient architecture with low CPU overhead
Easily interfaces to most 16-bit embedded CPU’s
1.8V to 3.3V variable voltage I/O accommodates wide
range of I/O signalling without voltage level shifters
Integrated PHY with HP Auto-MDIX support
Integrated checksum offload engine helps reduce
CPU load
Low pin count and small body size package for small
form factor system designs
—
—
—
—
—
—
—
—
—
—
„
„
„
„
„
„
„
Cable, satellite, and IP set-top boxes
Digital video recorders and DVD recorder/players
Digital TV
Digital media clients/servers and home gateways
Video-over IP solutions, IP PBX & video phones
Wireless routers & access points
High-end audio distribution systems
„
„
„
„
Minimizes CPU overhead
— Supports Slave-DMA
— Interrupt Pin with Programmable Hold-off timer
„
„
„
Reduces system cost and increases design flexibility
SRAM-like interface easily interfaces to most
embedded CPU’s or SoC’s
Reduced Power Modes
—
—
—
—
—
Host bus interface
Simple, SRAM-like interface
16-bit data bus
16Kbyte FIFO with flexible TX/RX allocation
One configurable host interrupt
Miscellaneous features
— Small form factor, 56-pin QFN lead-free RoHS
Compliant package
— Integrated 1.8V regulator
— Integrated checksum offload engine
— Mixed endian support
— General Purpose Timer
— Optional EEPROM interface
— Support for 3 status LEDs multiplexed with
Programmable GPIO signals
Minimizes dropped packets
— Internal buffer memory can store over 200 packets
— Automatic PAUSE and back-pressure flow control
„
Integrated 10/100 Ethernet PHY
—
—
—
—
Non-PCI Ethernet controller for high performance
applications
— 16-bit interface with fast bus cycle times
— Burst-mode read support
One 48-bit perfect address
64 hash-filtered multicast addresses
Pass all multicast
Promiscuous mode
Inverse filtering
Pass all incoming with status report
Disable reception of broadcast packets
— Supports HP Auto-MDIX
— Auto-negotiation
— Supports energy-detect power down
Key Benefits
„
Fully compliant with IEEE 802.3/802.3u standards
Integrated Ethernet MAC and PHY
10BASE-T and 100BASE-TX support
Full- and Half-duplex support
Full-duplex flow control
Backpressure for half-duplex flow control
Preamble generation and removal
Automatic 32-bit CRC generation and checking
Automatic payload padding and pad removal
Loop-back modes
Flexible address filtering modes
—
—
—
—
—
—
—
Target Applications
„
Single chip Ethernet controller
„
„
Single 3.3V Power Supply with Variable Voltage I/O
Commercial and Industrial Temperature Support
Numerous power management modes
Wake on LAN
Magic packet wakeup
Wakeup indicator event signal
Link Status Change
SMSC LAN9221/LAN9221i
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
ORDER NUMBER(S):
LAN9221-ABZJ FOR 56-PIN, QFN LEAD-FREE ROHS COMPLIANT PACKAGE (0 TO +70°C TEMP RANGE)
LAN9221i-ABZJ FOR 56-PIN, QFN LEAD-FREE ROHS COMPLIANT PACKAGE (-40 TO +85°C TEMP RANGE)
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123
Copyright © 2008 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 2.6 (12-04-08)
2
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table of Contents
Chapter 1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Block Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10/100 Ethernet PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10/100 Ethernet MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive and Transmit FIFOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Host Bus Interface (SRAM Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
12
12
12
13
13
13
13
13
13
14
Chapter 2 Pin Description and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1
2.2
2.3
Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
External Pull-Up/Pull-Down Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
10/100 Ethernet MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Full-Duplex Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
Half-Duplex Flow Control (Backpressure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3
Virtual Local Area Network (VLAN) Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address Filtering Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filtering Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.1
Perfect Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.2
Hash Only Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake-up Frame Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1
Magic Packet Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checksum Offload Engines (COE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.1
Receive Checksum Offload Engine (RXCOE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.2
Transmit Checksum Offload Engine (TXCOE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Host Bus Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7.1
Bus Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7.2
Bus Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7.3
Mixed Endian Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7.4
Word Swap Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Timer (GP Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.1
MAC Address Auto-Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.2
EEPROM Host Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.3 Internal PHY Power-Down Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detailed Reset Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.1 Hardware Reset Input (nRESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.2 Resume Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.3 Soft Reset (SRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11.4 PHY Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9221/LAN9221i
3
DATASHEET
23
24
24
24
24
25
26
26
26
27
29
30
30
33
34
34
34
35
35
38
39
39
39
44
44
44
47
48
49
49
49
49
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.12
3.13
TX Data Path Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.1 TX Buffer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.2 TX Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.3 TX Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.4 TX Status Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.5 Calculating Actual TX Data FIFO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.6 Transmit Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.7 Transmitter Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12.8 Stopping and Starting the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Data Path Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.1 RX Slave PIO Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.2 RX Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.3 RX Status Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.4 Stopping and Starting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.13.5 Receiver Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
51
52
54
55
56
57
62
62
62
63
65
66
67
67
Chapter 4 Internal Ethernet PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
Top Level Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100Base-TX Transmit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
4B/5B Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2
Scrambling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3
NRZI and MLT3 Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
100M Transmit Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5
100M Phase Lock Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100Base-TX Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
100M Receive Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Equalizer, Baseline Wander Correction and Clock and Data Recovery . . . . . . . . . . . . .
4.3.3
NRZI and MLT-3 Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.4
Descrambling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.5
Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.6
5B/4B Decoding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10Base-T Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.1
10M Transmit Data across the internal MII bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.2
Manchester Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.3
10M Transmit Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10Base-T Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.1
10M Receive Input and Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.2
Manchester Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.3
Jabber Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.1
Re-starting Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.2
Disabling Auto-negotiation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.3
Half vs. Full-Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HP Auto-MDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
68
68
70
70
70
70
71
71
71
71
72
72
72
72
72
72
73
73
73
73
73
73
75
75
75
75
76
Chapter 5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5.1
5.2
5.3
Register Nomenclature and Access Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX and TX FIFO Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.1
RX FIFO Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.2
TX FIFO Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Control and Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.1
ID_REV—Chip ID and Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.2
IRQ_CFG—Interrupt Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision 2.6 (12-04-08)
4
DATASHEET
79
79
79
79
80
81
81
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4
5.5
5.3.3
INT_STS—Interrupt Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.3.4
INT_EN—Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.3.5
BYTE_TEST—Byte Order Test Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.3.6
FIFO_INT—FIFO Level Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.3.7
RX_CFG—Receive Configuration Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.3.8
TX_CFG—Transmit Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5.3.9
HW_CFG—Hardware Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.3.10 RX_DP_CTRL—Receive Datapath Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
5.3.11 RX_FIFO_INF—Receive FIFO Information Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.3.12 TX_FIFO_INF—Transmit FIFO Information Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.3.13 PMT_CTRL— Power Management Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
5.3.14 GPIO_CFG—General Purpose IO Configuration Register . . . . . . . . . . . . . . . . . . . . . . . 96
5.3.15 GPT_CFG-General Purpose Timer Configuration Register . . . . . . . . . . . . . . . . . . . . . . 97
5.3.16 GPT_CNT-General Purpose Timer Current Count Register . . . . . . . . . . . . . . . . . . . . . . 98
5.3.17 WORD_SWAP—Word Swap Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5.3.18 FREE_RUN—Free-Run 25MHz Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5.3.19 RX_DROP– Receiver Dropped Frames Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5.3.20 MAC_CSR_CMD – MAC CSR Synchronizer Command Register . . . . . . . . . . . . . . . . 100
5.3.21 MAC_CSR_DATA – MAC CSR Synchronizer Data Register . . . . . . . . . . . . . . . . . . . . 100
5.3.22 AFC_CFG – Automatic Flow Control Configuration Register . . . . . . . . . . . . . . . . . . . . 101
5.3.23 E2P_CMD – EEPROM Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.3.24 E2P_DATA – EEPROM Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
MAC Control and Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.4.1
MAC_CR—MAC Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.4.2
ADDRH—MAC Address High Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5.4.3
ADDRL—MAC Address Low Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
5.4.4
HASHH—Multicast Hash Table High Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
5.4.5
HASHL—Multicast Hash Table Low Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
5.4.6
MII_ACC—MII Access Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
5.4.7
MII_DATA—MII Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
5.4.8
FLOW—Flow Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
5.4.9
VLAN1—VLAN1 Tag Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
5.4.10 VLAN2—VLAN2 Tag Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
5.4.11 WUFF—Wake-up Frame Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
5.4.12 WUCSR—Wake-up Control and Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
5.4.13 COE_CR—Checksum Offload Engine Control Register . . . . . . . . . . . . . . . . . . . . . . . . 117
PHY Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
5.5.1
Basic Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
5.5.2
Basic Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
5.5.3
PHY Identifier 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
5.5.4
PHY Identifier 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
5.5.5
Auto-negotiation Advertisement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
5.5.6
Auto-negotiation Link Partner Ability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
5.5.7
Auto-negotiation Expansion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
5.5.8
Mode Control/Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
5.5.9
Special Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
5.5.10 Special Control/Status Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
5.5.11 Interrupt Source Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
5.5.12 Interrupt Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
5.5.13 PHY Special Control/Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Chapter 6 Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
6.1
6.2
Equivalent Test Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Host Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
6.2.1
Special Restrictions on Back-to-Back Write/Read Cycles . . . . . . . . . . . . . . . . . . . . . . . 129
SMSC LAN9221/LAN9221i
5
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.2.2
Special Restrictions on Back-to-Back Read Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIO Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIO Burst Reads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Data FIFO Direct PIO Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Data FIFO Direct PIO Burst Reads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIO Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Data FIFO Direct PIO Writes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
131
132
133
134
135
136
137
138
Chapter 7 Operational Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Absolute Maximum Ratings*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Conditions** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Consumption (Device Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Consumption (Device and System Components) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Worst Case Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
139
139
140
141
142
143
147
Chapter 8 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
8.1
56-QFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Chapter 9 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Revision 2.6 (12-04-08)
6
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
List of Figures
Figure 1.1
Figure 1.2
Figure 2.1
Figure 3.1
Figure 3.4
Figure 3.5
Figure 3.6
Figure 3.7
Figure 3.8
Figure 3.9
Figure 3.2
Figure 3.3
Figure 3.4
Figure 3.5
Figure 3.6
Figure 3.7
Figure 3.8
Figure 3.9
Figure 3.10
Figure 3.11
Figure 3.12
Figure 3.13
Figure 3.14
Figure 3.15
Figure 3.16
Figure 3.17
Figure 3.18
Figure 3.19
Figure 3.20
Figure 3.21
Figure 4.1
Figure 4.2
Figure 4.3
Figure 5.1
Figure 5.2
Figure 6.1
Figure 6.2
Figure 6.3
Figure 6.4
Figure 6.5
Figure 6.6
Figure 6.7
Figure 6.8
Figure 8.1
Figure 8.2
System Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Internal Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
56-QFN Pin Configuration (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VLAN Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RXCOE Checksum Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Type II Ethernet Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Ethernet Frame with VLAN Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Ethernet Frame with Length Field and SNAP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Ethernet Frame with VLAN Tag and SNAP Header. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ethernet Frame with multiple VLAN Tags and SNAP Header . . . . . . . . . . . . . . . . . . . . . . . . 32
LAN9221/LAN9221i Host Data Path Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
FIFO Access Byte Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
EEPROM Access Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
EEPROM ERASE Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
EEPROM ERAL Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
EEPROM EWDS Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
EEPROM EWEN Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
EEPROM READ Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
EEPROM WRITE Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
EEPROM WRAL Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PME and PME_INT Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Simplified Host TX Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
TX Buffer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
TX Example 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
TX Example 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
TX Example 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Host Receive Routine Using Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Host Receive Routine with Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
RX Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
RX Packet Format with RX Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
100Base-TX Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Receive Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Direct cable connection vs. Cross-over cable connection.. . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Example ADDRL, ADDRH and EEPROM Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Equivalent Test Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
PIO Read Cycle Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
RX Data FIFO Direct PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
RX Data FIFO Direct PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
TX Data FIFO Direct PIO Write Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
EEPROM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
56 Pin QFN Package Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
56 Pin QFN Recommended PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
SMSC LAN9221/LAN9221i
7
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
List of Tables
Table 2.1 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 2.2 LAN Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 2.3 Serial EEPROM Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 2.4 System and Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 2.5 56-QFN Package Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 2.6 External Pull-Up/Pull-Down Resistor Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 2.7 Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 3.1 Address Filtering Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 3.2 Wake-Up Frame Filter Register Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.3 Filter i Byte Mask Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.4 Filter i Command Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.5 Filter i Offset Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 3.6 Filter i CRC-16 Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 3.7 TX Checksum Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 3.8 Endian Ordering Logic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 3.9 Required EECLK Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 3.10 Power Management States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 3.11 Reset Sources and Affected Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 3.12 TX Command 'A' Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 3.13 TX Command 'B' Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 3.14 TX DATA Start Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 4.1 4B/5B Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 4.2 CRS Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 5.1 Direct Address Register Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 5.2 RX Alignment Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 5.3 Valid TX/RX FIFO Allocations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Table 5.4 EEPROM Enable Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table 5.5 Backpressure Duration Bit Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Table 5.6 MAC CSR Register Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Table 5.7 ADDRL, ADDRH and EEPROM Byte Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Table 5.8 LAN9221/LAN9221i PHY Control and Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Table 5.9 MODE Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Table 6.1 Read After Write Timing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Table 6.2 Read After Read Timing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Table 6.3 PIO Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Table 6.4 PIO Burst Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Table 6.5 RX Data FIFO Direct PIO Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Table 6.6 RX Data FIFO Direct PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Table 6.7 PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Table 6.8 TX Data FIFO Direct PIO Write Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Table 6.9 Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Table 6.10 EEPROM Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Table 7.1 Power Consumption Device Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Table 7.2 Power Consumption Device and System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Table 7.3 Maximum Supply Current Characteristics VDDVARIO=3.3V + 300mV. . . . . . . . . . . . . . . . . 142
Table 7.4 Maximum Supply Current Characteristics VDDVARIO=2.5V + 10%. . . . . . . . . . . . . . . . . . . 142
Table 7.5 Maximum Supply Current Characteristics VDDVARIO=1.8V + 10%. . . . . . . . . . . . . . . . . . . 142
Table 7.6 I/O Buffer Characteristics VDDVARIO=3.3V +/- 300mV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Table 7.7 I/O Buffer Characteristics VDDVARIO=2.5V +/- 10% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Table 7.8 I/O Buffer Characteristics VDDVARIO=1.8V +/- 10% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Table 7.9 100BASE-TX Transceiver Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Table 7.10 10BASE-T Transceiver Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Revision 2.6 (12-04-08)
8
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 7.11 LAN9221/LAN9221i Crystal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Table 8.1 56 Pin QFN Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Table 9.1 Customer Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
SMSC LAN9221/LAN9221i
9
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 1 General Description
The LAN9221/LAN9221i is a full-featured, single-chip 10/100 Ethernet controller designed for
embedded applications where performance, flexibility, ease of integration and system cost control are
required. The LAN9221/LAN9221i has been specifically designed to provide high performance and
throughput for 16-bit applications. The LAN9221/LAN9221i is fully IEEE 802.3 10BASE-T and 802.3u
100BASE-TX compliant, and supports HP Auto-MDIX. The variable voltage I/O signals of the
LAN9221/LAN9221i accommodate lower voltage I/O signalling without the need for voltage level
shifters.
The LAN9221/LAN9221i includes an integrated Ethernet MAC and PHY with a high-performance
SRAM-like slave interface. The simple, yet highly functional host bus interface provides a glue-less
connection to most common 16-bit microprocessors and microcontrollers as well as 32-bit
microprocessors with a 16-bit external bus. The integrated checksum offload engines enable the
automatic generation of the 16-bit checksum for received and transmitted Ethernet frames, offloading
the task from the CPU. The LAN9221/LAN9221i also includes large transmit and receive data FIFOs
to accommodate high latency applications. In addition, the LAN9221/LAN9221i memory buffer
architecture allows highly efficient use of memory resources by optimizing packet granularity.
Applications
The LAN9221/LAN9221i is well suited for many high-performance embedded applications, including:
„
Cable, satellite and IP set-top boxes
„
High-end audio distribution systems
„
Digital video recorders
„
DVD Recorders/Players
„
Digital TV
„
Digital media clients/servers
„
Home gateways
„
Industrial and embedded systems with extended temperature support
The LAN9221/LAN9221i also supports features which reduce or eliminate packet loss. Its internal 16KByte SRAM can hold over 200 received packets. If the receive FIFO gets too full, the
LAN9221/LAN9221i can automatically generate flow control packets to the remote node, or assert
back-pressure on the remote node by generating network collisions.
The LAN9221/LAN9221i supports numerous power management and wakeup features. The
LAN9221/LAN9221i can be placed in a reduced power mode and can be programmed to issue an
external wake signal via several methods, including “Magic Packet”, “Wake on LAN” and “Link Status
Change”. This signal is ideal for triggering system power-up using remote Ethernet wakeup events.
The device can be removed from the low power state via a host processor command.
Revision 2.6 (12-04-08)
10
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
1.1
Block Diagram
System Memory
System
Peripherals
Microprocessor/
Microcontroller
System Bus
LAN9221/
LAN9221i
25MHz
XTAL
Magnetics
Ethernet
LEDS/
GPIO
EEPROM
(Optional)
Figure 1.1 System Block Diagram
The SMSC LAN9221/LAN9221i integrated 10/100 MAC/PHY controller is a peripheral chip that
performs the function of translating parallel data from a host controller into Ethernet packets. The
LAN9221/LAN9221i Ethernet MAC/PHY controller is designed and optimized to function in an
embedded environment. All communication is performed with programmed I/O transactions using the
simple SRAM-like host interface bus.
The diagram shown above, describes a typical system configuration of the LAN9221/LAN9221i in a
typical embedded environment.
The LAN9221/LAN9221i is a general purpose, platform independent, Ethernet controller. The
LAN9221/LAN9221i consists of four major functional blocks. The four blocks are:
„
10/100 Ethernet PHY
„
10/100 Ethernet MAC
„
RX/TX FIFOs
„
Host Bus Interface (HBI)
SMSC LAN9221/LAN9221i
11
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
1.2
Internal Block Overview
This section provides an overview of each of these functional blocks as shown in Figure 1.2, "Internal
Block Diagram".
25MHz
EEPROM
(Optional)
+3.3V
PME
Wakup Indicator
Power
Management
Host Bus Interface
(HBI)
16-bit SRAM I/F
3.3V to 1.8V
Core Regulator
2kB to 14kB
Configurable TX FIFO
RX Status FIFO
IRQ
Interrupt
Controller
GP Timer
RX Checksum
Offload Engine
TX Checksum
Offload Engine
10/100
Ethernet
MAC
TX Status FIFO
PIO Controller
FIFO_SEL
EEPROM
Controller
PLL
2kB to 14kB
Configurable RX FIFO
10/100
Ethernet
PHY
LAN
MIL - RX Elastic
Buffer - 128 bytes
MIL - TX Elastic
Buffer - 2K bytes
Figure 1.2 Internal Block Diagram
1.3
10/100 Ethernet PHY
The LAN9221/LAN9221i integrates an IEEE 802.3 physical layer for twisted pair Ethernet applications.
The PHY can be configured for either 100 Mbps (100BASE-TX) or 10 Mbps (10BASE-T) Ethernet
operation in either full or half duplex configurations. The PHY block supports HP Auto-MDIX and autonegotiation.
Minimal external components are required for the utilization of the Integrated PHY.
1.4
10/100 Ethernet MAC
The transmit and receive data paths are separate within the MAC allowing the highest performance
especially in full duplex mode. The data paths connect to the PIO interface Function via separate
busses to increase performance. Payload data as well as transmit and receive status is passed on
these busses.
A third internal bus is used to access the MAC’s Control and Status Registers (CSR’s). This bus is
accessible from the host through the PIO interface function.
On the backend, the MAC interfaces with the internal 10/100 PHY through a MII (Media Independent
Interface) port internal to the LAN9221/LAN9221i. The MAC CSR's also provide a mechanism for
accessing the PHY’s internal registers through the internal SMI (Serial Management Interface) bus.
The MAC Interface Layer (MIL), within the MAC, contains a 2K Byte transmit and a 128 Byte receive
FIFO which is separate from the TX and RX FIFOs. The FIFOs within the MAC are not directly
accessible from the host interface. The differentiation between the TX/RX FIFO memory buffers and
the MAC buffers is that when the transmit or receive packets are in the MAC buffers, the host no longer
Revision 2.6 (12-04-08)
12
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
can control or access the TX or RX data. The MAC buffers (both TX and RX) are in effect the working
buffers of the Ethernet MAC logic. In the case of reception, the data must be moved first to the RX
FIFOs for the host to access the data. For TX operations, the MIL operates in store-and-forward mode
and will queue an entire frame before beginning transmission.
1.5
Receive and Transmit FIFOs
The Receive and Transmit FIFOs allow increased packet buffer storage to the MAC. The FIFOs are a
conduit between the host interface and the MAC through which all transmitted and received data and
status information is passed. Deep FIFOs allow a high degree of latency tolerance relative to the
various transport and OS software stacks thus reducing or minimizing overrun conditions. Like the
MAC, the FIFOs have separate receive and transmit data paths. In addition, the RX and TX FIFOs are
configurable in size, allowing increased flexibility.
1.6
Interrupt Controller
The LAN9221/LAN9221i supports a single programmable interrupt. The programmable nature of this
interrupt allows the user the ability to optimize performance dependent upon the application
requirement. Both the polarity and buffer type of the interrupt pin are configurable for the external
interrupt processing. The interrupt line can be configured as an open-drain output to facilitate the
sharing of interrupts with other devices. In addition, a programmable interrupt de-assertion interval is
provided.
1.7
GPIO Interface
A 3-bit GPIO and 2-bit GPO (Multiplexed on the EEPROM and LED Pins) interface is included in the
LAN9221/LAN9221i. It is accessible through the host bus interface via the CSRs. The GPIO signals
can function as inputs, push-pull outputs and open drain outputs. The GPIO’s (GPO’s are not
configurable) can also be configured to trigger interrupts with programmable polarity.
1.8
Serial EEPROM Interface
A serial EEPROM interface is included in the LAN9221/LAN9221i. The serial EEPROM is optional and
can be programmed with the LAN9221/LAN9221i MAC address. The LAN9221/LAN9221i can
optionally load the MAC address automatically after hardware reset, or soft reset.
1.9
Power Management Controls
The LAN9221/LAN9221i supports comprehensive array of power management modes to allow use in
power sensitive applications. Wake on LAN, Link Status Change and Magic Packet detection are
supported by the LAN9221/LAN9221i. An external PME (Power Management Event) interrupt is
provided to indicate detection of a wakeup event.
1.10
General Purpose Timer
The general-purpose timer has no dedicated function within the LAN9221/LAN9221i and may be
programmed to issue a timed interrupt.
SMSC LAN9221/LAN9221i
13
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
1.11
Host Bus Interface (SRAM Interface)
The host bus interface provides a FIFO interface for the transmit and receive data paths, as well as
an interface for the LAN9221/LAN9221i Control and Status Registers (CSR’s).
The host bus interface is the primary bus for connection to the embedded host system. This interface
models an asynchronous SRAM. TX FIFO, RX FIFO, and CSR’s are accessed through this interface.
Programmed I/O transactions are supported.
The LAN9221/LAN9221i host bus interface supports 16-bit bus transfers. Internally, all data paths are
32-bits wide. The LAN9221/LAN9221i can be interfaced to either Big-Endian or Little-Endian
processors and includes mixed endian support for FIFO accesses.
Revision 2.6 (12-04-08)
14
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
nRESET
PME
EECLK/GPO4**
EECS
EEDIO/GPO3**
VDD18CORE
D0
D1
D2
D3
D4
D5
VDDVARIO
D6
42
41
40
39
38
37
36
35
34
33
32
31
30
29
Chapter 2 Pin Description and Configuration
IRQ
43
28
D7
TPO-
44
27
D8
TPO+
45
26
D9
VDD33A
46
25
D10
TPI-
47
56-QFN
24
VDDVARIO
TPI+
48
(TOP VIEW)
23
D11
VDD33A
49
22
D12
SMSC
LAN9221/LAN9221i
VSS
14
nRD
TEST
15
13
56
FIFO_SEL
VDDVARIO
12
nWR
A1
16
11
55
A2
XTAL1/CLKIN**
10
nCS
A3
17
9
54
A4
XTAL2
8
VDDVARIO
A5
18
7
53
A6
VDD18A
6
D15
A7
19
5
52
GPIO2/nLED3**
AMDIX_EN
4
D14
GPIO1/nLED2**
20
3
51
GPIO0/nLED1**
VDD33A
2
D13
VDD18CORE
21
1
50
VDD33REG
EXRES
**DENOTES A MULTIFUNCTION PIN
NOTE: When HP Auto-MDIX is activated, the TPO+/- pins can function as TPI+/- and vice-versa
NOTE: Exposed pad (VSS) on bottom of package must be connected to ground
Figure 2.1 56-QFN Pin Configuration (Top View)
SMSC LAN9221/LAN9221i
15
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
2.1
Pin List
Table 2.1 Host Bus Interface Signals
NAME
SYMBOL
BUFFER
TYPE
#
PINS
Host Data
D[15:0]
VIS/VO8
16
Bi-directional data port.
Host Address
A[7:1]
VIS
7
7-bit Address Port. Used to select Internal CSR’s and
TX and RX FIFOs.
Read Strobe
nRD
VIS
1
Active low strobe to indicate a read cycle.
Write Strobe
nWR
VIS
1
Active low strobe to indicate a write cycle. This signal,
qualified with nCS, is also used to wakeup the
LAN9221/LAN9221i when it is in a reduced power
state.
Chip Select
nCS
VIS
1
Active low signal used to qualify read and write
operations. This signal qualified with nWR is also used
to wakeup the LAN9221/LAN9221i when it is in a
reduced power state.
Interrupt
Request
IRQ
VO8/
VOD8
1
Programmable Interrupt request. Programmable
polarity, source and buffer types.
FIFO Select
FIFO_SEL
VIS
1
When driven high all accesses to the
LAN9221/LAN9221i are to the RX or TX Data FIFOs.
In this mode, the A[7:3] upper address inputs are
ignored.
DESCRIPTION
Table 2.2 LAN Interface Signals
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
TPO+
TPO+
AO
1
Transmit Positive Output (normal)
Receive Positive Input (reversed)
TPO-
TPO-
AO
1
Transmit Negative Output (normal)
Receive Negative Input (reversed)
TPI+
TPI+
AI
1
Receive Positive Input (normal)
Transmit Positive Input (reversed)
TPI-
TPI-
AI
1
Receive Negative Input (normal)
Transmit Negative Output (reversed)
PHY External Bias
Resistor
EXRES
AI
1
Must be connected to ground through a 12.4K
ohm 1% resistor.
DESCRIPTION
Note: The pin names for the twisted pair pins shown above apply to a normal connection. If HP AutoMDIX is enabled and a reverse connection is detected, or a reverse connection is manually
selected, the input pins become outputs, and vice-versa, as indicated in the descriptions.
Revision 2.6 (12-04-08)
16
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 2.3 Serial EEPROM Interface Signals
NAME
SYMBOL
EEPROM Data,
GPO3, TX_EN,
TX_CLK
EEDIO/GPO3/
TX_EN/TX_CLK
BUFFER
TYPE
NUM
PINS
VIS/VO8
1
DESCRIPTION
EEPROM Data: This bi-directional pin can be
connected to a serial EEPROM DIO. This is
optional.
General Purpose Output 3: This pin can also
function as a general purpose output, or it can
be configured to monitor the TX_EN or
TX_CLK signals on the internal MII port. When
configured as a GPO signal, or as a
TX_EN/TX_CLK monitor, the EECS pin is
deasserted so as to never unintentionally
access the serial EEPROM. This signal cannot
function as a general-purpose input.
EEPROM Chip
Select
EECS
VO8
1
Serial EEPROM chip select.
EEPROM Clock,
GPO4 RX_DV,
RX_CLK
EECLK/GPO4/
RX_DV/RX_CLK
VO8
(PU)
1
EEPROM Clock: Serial EEPROM Clock pin.
SMSC LAN9221/LAN9221i
General Purpose Output 4: This pin can also
function as a general-purpose output, or it can
be configured to monitor the RX_DV or
RX_CLK signals on the internal MII port. When
configured as a GPO signal, or as an
RX_DV/RX_CLK monitor, the EECS pin is
deasserted so as to never unintentionally
access the serial EEPROM. This signal cannot
function as a general-purpose input.
17
DATASHEET
Note:
When the EEPROM interface is not
used, the EECLK pin must be left
unconnected.
Note:
When operating at reduced
VDDVARIO voltage levels (less than
3.0V), this pin must be pulled-up with
an external resistor. Refer to Section
2.2, "External Pull-Up/Pull-Down
Resistors" for more information.
Note:
This pin must not be pulled low by an
external resistor or driven low
externally under any conditions.
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 2.4 System and Power Signals
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
Crystal 1, Clock In
XTAL1/CLKIN
lCLK
1
External 25MHz Crystal Input. This pin can also
be connected to single-ended TTL oscillator
(CLKIN). If this method is implemented, XTAL2
should be left unconnected.
Crystal 2
XTAL2
OCLK
1
External 25MHz Crystal output.
Reset
nRESET
VIS
(PU)
1
Active-low reset input. Resets all logic and
registers within the LAN9221/LAN9221i. This
signal is pulled high with a weak internal pull-up
resistor.
Wakeup Indicator
PME
VO8/
VOD8
1
DESCRIPTION
Note:
The LAN9221/LAN9221i must be reset
on power-up via nRESET or following
power-up via a soft reset (SRST). The
LAN9221/LAN9221i must always be
read at least once after reset, or upon
return from a power-saving state or
write operations will not function. See
Section 3.11, "Detailed Reset
Description," on page 48 for additional
information
Note:
When operating at reduced
VDDVARIO voltage levels (less than
3.0V), this pin must be pulled-high to
a valid level with an external resistor
or must be driven as an input. Refer to
Section 2.2, "External Pull-Up/PullDown Resistors" for more information.
When programmed to do so, is asserted when
the LAN9221/LAN9221i detects a wake event
and is requesting the system to wake up from
the associated sleep state. The polarity and
buffer type of this signal is programmable.
Note:
Revision 2.6 (12-04-08)
18
DATASHEET
Detection of a Power Management
Event, and assertion of the PME
signal will not wakeup the
LAN9221/LAN9221i. The
LAN9221/LAN9221iwill only wake up
when it detects a host write cycle
(assertion of nCS and nWR). Although
any write to the LAN9221/LAN9221i,
regardless of the data written, will
wake-up the device when it is in a
power-saving mode, it is required that
the BYTE_TEST register be used for
this purpose.
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 2.4 System and Power Signals (continued)
NAME
SYMBOL
Auto-MDIX Enable
AMDIX_EN
BUFFER
TYPE
NUM
PINS
VIS
(PU)
1
DESCRIPTION
Enables Auto-MDIX. Pull high or leave
unconnected to enable Auto-MDIX, pull low to
disable Auto-MDIX.
Note:
Test
General Purpose
I/O data,
nLED1 (Speed
Indicator),
nLED2 (Link &
Activity Indicator),
TEST
GPIO[2:0]/
nLED[3:1]
VIS
(PD)
1
VIS/
VO12/
VOD12
3
Reserved for internal test purposes only.
Note:
nLED3 (FullDuplex
Indicator).
When operating at reduced
VDDVARIO voltage levels (less than
3.0V), this pin must be pulled to a valid
level with an external resistor. Refer to
Section 2.2, "External Pull-Up/PullDown Resistors" for more information.
When operating at a reduced
VDDVARIO voltage (less than 3.0V),
this pin must be connected to ground
or pulled-low with an external resistor.
When VDDVARIO = 3.3V, this pin may
be left unconnected. Refer to Section
2.2, "External Pull-Up/Pull-Down
Resistors" for more information.
General Purpose I/O data: These three
general-purpose signals are fully programmable
as either push-pull output, open-drain output or
input by writing the GPIO_CFG configuration
register in the CSR’s. They are also multiplexed
as GP LED connections.
GPIO signals are Schmitt-triggered inputs.
When configured as LED outputs these signals
are open-drain.
nLED1 (Speed Indicator). This signal is driven
low when the operating speed is 100Mbs,
during auto-negotiation and when the cable is
disconnected. This signal is driven high only
during 10Mbs operation.
nLED2 (Link & Activity Indicator). This signal
is driven low (LED on) when the
LAN9221/LAN9221i detects a valid link. This
signal is pulsed high (LED off) for 80mS
whenever transmit or receive activity is
detected. This signal is then driven low again
for a minimum of 80mS, after which time it will
repeat the process if TX or RX activity is
detected. Effectively, LED2 is activated solid for
a link. When transmit or receive activity is
sensed LED2 will flash as an activity indicator.
nLED3 (Full-Duplex Indicator). This signal is
driven low when the link is operating in fullduplex mode.
Variable Voltage
I/O Power
VDDVARIO
P
4
Common Ground
VSS
P
1 pad
+3.3V Regulator
Power Supply
VDD33REG
P
1
SMSC LAN9221/LAN9221i
19
DATASHEET
Variable Voltage I/O logic power supply pins.
Refer to Section 7.2, "Operating Conditions**,"
on page 139 for additional details.
Common Ground
+3.3V power supply for internal +1.8V regulator.
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 2.4 System and Power Signals (continued)
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
+3.3V Analog
Power
VDD33A
P
3
+3.3V analog power supply pins.
+1.8V Analog
Power
VDD18A
P
1
+1.8V analog power supply pin. This pin must
be connected externally to VDD18CORE.
Core Voltage
Decoupling
VDD18CORE
P
2
+1.8 V from internal core regulator. Both pins
must be connected together externally. Each
pin requires a 0.01uF decoupling capacitor. In
addition, pin 2 requires a bulk 4.7uF capacitor
(<2 Ohm ESR) in parallel. These pins must not
be used to supply power to other external
devices.
DESCRIPTION
Table 2.5 56-QFN Package Pin Assignments
PIN
NUM
PIN NAME
PIN
NUM
PIN NAME
PIN
NUM
PIN NAME
PIN
NUM
PIN NAME
1
VDD33REG
15
nRD
29
D6
43
IRQ
2
VDD18CORE
16
nWR
30
VDDVARIO
44
TPO-
3
GPIO0/nLED1
17
nCS
31
D5
45
TPO+
4
GPIO1/nLED2
18
VDDVARIO
32
D4
46
VDD33A
5
GPIO2/nLED3
19
D15
33
D3
47
TPI-
6
A7
20
D14
34
D2
48
TPI+
7
A6
21
D13
35
D1
49
VDD33A
8
A5
22
D12
36
D0
50
EXRES
9
A4
23
D11
37
VDD18CORE
51
VDD33A
10
A3
24
VDDVARIO
38
EEDIO/GPO3
52
AMDIX_EN
11
A2
25
D10
39
EECS
53
VDD18A
12
A1
26
D9
40
EECLK/GPO4
54
XTAL2
13
FIFO_SEL
27
D8
41
PME
55
XTAL1/CLKIN
14
TEST
28
D7
42
nRESET
56
VDDVARIO
EXPOSED PAD
MUST BE CONNECTED TO VSS
2.2
External Pull-Up/Pull-Down Resistors
As detailed in Table 2.6, when using an external pull-up or pull-down resistor, the required value is
dependant on the operating voltage. Usage of recommended pull-up/pull-down resistor values is
required to ensure proper operation.
Revision 2.6 (12-04-08)
20
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 2.6 External Pull-Up/Pull-Down Resistor Values
SMSC LAN9221/LAN9221i
I/O VOLTAGE
PULL-UP/PULL-DOWN RESISTOR VALUE (OHMS)
3.3V +/- 300mV
10K
2.5 +/- 10%
7.5K
1.8V +/- 10%
4.7K
21
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
2.3
Buffer Types
Table 2.7 Buffer Types
TYPE
VIS
VO12
VOD12
VO8
VOD8
DESCRIPTION
Variable voltage input pin
Variable voltage output with 12mA sink and 12mA source (Note 2.1)
Variable voltage open-drain output with 12mA sink (Note 2.1)
Variable voltage output 8mA symmetrical drive (Note 2.1)
Variable voltage open-drain output with 8 mA sink (Note 2.1)
PU
50uA (typical) internal pull-up (Note 2.2)
PD
50uA (typical) internal pull-down (Note 2.2)
AI
Analog input
AO
Analog output
AIO
Analog bi-directional
ICLK
Crystal oscillator input pin
OCLK
Crystal oscillator output pin
Note 2.1
Sink and source capabilities are dependant on the VDDVARIO voltage. Refer to Section
7.6, "DC Electrical Specifications" for additional information.
Note 2.2
When operating at reduced VDDVARIO voltage levels (less than 3.0V), do not rely on
internal pull-up and pull-down resistors to determine signal state. Refer to Section 2.2,
"External Pull-Up/Pull-Down Resistors" and the individual signal descriptions in Section
2.1, "Pin List" for more information.
Revision 2.6 (12-04-08)
22
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 3 Functional Description
3.1
10/100 Ethernet MAC
The Ethernet Media Access controller (MAC) incorporates the essential protocol requirements for
operating an Ethernet/IEEE 802.3-compliant node and provides an interface between the host
subsystem and the internal Ethernet PHY. The MAC can operate in either 100-Mbps or 10-Mbps mode.
The MAC operates in both half-duplex and full-duplex modes. When operating in half-duplex mode,
the MAC complies fully with Section 4 of ISO/IEC 8802-3 (ANSI/IEEE standard) and ANSI/IEEE 802.3
standards. When operating in full-duplex mode, the MAC complies with IEEE 802.3x full-duplex
operation standard.
The MAC provides programmable enhanced features designed to minimize host supervision, bus
utilization, and pre- or post-message processing. These features include the ability to disable retries
after a collision, dynamic FCS (Frame Check Sequence) generation on a frame-by-frame basis,
automatic pad field insertion and deletion to enforce minimum frame size attributes, layer 3 checksum
calculation for transmit and receive operations, and automatic retransmission and detection of collision
frames.
The MAC can sustain transmission or reception of minimally-sized back-to-back packets at full line
speed with an interpacket gap (IPG) of 9.6 microseconds for 10 Mbps and 0.96 microseconds for 100
Mbps.
The primary attributes of the MAC Function are:
„
Transmit and receive message data encapsulation
„
Framing (frame boundary delimitation, frame synchronization)
„
Error detection (physical medium transmission errors)
„
Media access management
„
Medium allocation (collision detection, except in full-duplex operation)
„
Contention resolution (collision handling, except in full-duplex operation)
„
Flow control during full-duplex mode
„
Decoding of control frames (PAUSE command) and disabling the transmitter
„
Generation of control frames
„
Interface to the internal PHY.
„
Checksum offload engine for calculation of layer 3 transmit and receive checksum.
The transmit and receive data paths are separate within the LAN9221/LAN9221i from the MAC to host
interface allowing the highest performance, especially in full duplex mode. Payload data as well as
transmit and receive status are passed on these busses.
A third internal bus is used to access the MAC’s “Control and Status Registers” (CSR’s). This bus is
also accessible from the host.
On the backend, the MAC interfaces with the 10/100 PHY through an MII (Media Independent
Interface) port which is internal to the LAN9221/LAN9221i. The MAC CSR's also provide a mechanism
for accessing the PHY’s internal registers through the internal SMI (Serial Management Interface) bus.
The receive and transmit FIFOs allow increased packet buffer storage to the MAC. The FIFOs are a
conduit between the host interface and the MAC through which all transmitted and received data and
status information is passed. Deep FIFOs allow a high degree of latency tolerance relative to the
various transport and OS software stacks reducing and minimizing overrun conditions. Like the MAC,
the FIFOs have separate receive and transmit data paths.
SMSC LAN9221/LAN9221i
23
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
The LAN9221/LAN9221i can store up to 250 Ethernet packets utilizing FIFOs, totaling 16K bytes, with
a packet granularity of 4 bytes. This memory is shared by the RX and TX blocks and is configurable
in terms of allocation. This depth of buffer storage minimizes or eliminates receive overruns.
3.2
Flow Control
The LAN9221/LAN9221i Ethernet MAC supports full-duplex flow control using the pause operation and
control frame. It also supports half-duplex flow control using back pressure.
3.2.1
Full-Duplex Flow Control
The pause operation inhibits data transmission of data frames for a specified period of time. A Pause
operation consists of a frame containing the globally assigned multicast address (01-80-C2-00-00-01),
the PAUSE opcode, and a parameter indicating the quantum of slot time (512 bit times) to inhibit data
transmissions. The PAUSE parameter may range from 0 to 65,535 slot times. The Ethernet MAC logic,
on receiving a frame with the reserved multicast address and PAUSE opcode, inhibits data frame
transmissions for the length of time indicated. If a Pause request is received while a transmission is
in progress, then the pause will take effect after the transmission is complete. Control frames are
received and processed by the MAC and are passed on.
The MAC also transmits control frames (pause command) via both hardware and software control. The
software driver requests the MAC to transmit a control frame and gives the value of the PAUSE time
to be used in the control frame. The MAC Function constructs a control frame with the appropriate
values set in all the different fields (as defined in the 802.3x specification) and transmits the frame to
the MII interface. The transmission of the control frame is not affected by the current state of the Pause
timer value that is set because of a recently received control frame.
3.2.2
Half-Duplex Flow Control (Backpressure)
In half-duplex mode, back pressure is used for flow control. Whenever the receive buffer/FIFO
becomes full or crosses a certain threshold level, the MAC starts sending a Jam signal. The MAC
transmit logic enters a state at the end of current transmission (if any), where it waits for the beginning
of a received frame. Once a new frame starts, the MAC starts sending the jam signal, which will result
in a collision. After sensing the collision, the remote station will back off its transmission. The MAC
continues sending the jam to make other stations defer transmission. The MAC only generates this
collision-based back pressure when it receives a new frame, in order to avoid any late collisions.
3.2.3
Virtual Local Area Network (VLAN) Support
Virtual Local Area Networks or VLANs, as defined within the IEEE 802.3 standard, provide network
administrators one means of grouping nodes within a larger network into broadcast domains. To
implement a VLAN, four extra bytes are added to the basic Ethernet packet. As shown in Figure 3.1,
"VLAN Frame", the four bytes are inserted after the Source Address Field and before the Type/Length
field. The first two bytes of the VLAN tag identify the tag, and by convention are set to the value
0x8100. The last two bytes identify the specific VLAN associated with the packet; they also provide a
priority field.
The LAN9221/LAN9221i supports VLAN-tagged packets. The LAN9221/LAN9221i provides two
registers which are used to identify VLAN-tagged packets. One register should normally be set to the
conventional VLAN ID of 0x8100. The other register provides a way of identifying VLAN frames tagged
with a proprietary (not 0x8100) identifier. If a packet arrives bearing either of these tags in the two
bytes succeeding the Source Address field, the controller will recognize the packet as a VLAN-tagged
packet. In this case, the controller increases the maximum allowed packet size from 1518 to 1522
bytes (normally the controller filters packets larger than 1518 bytes). This allows the packet to be
received, and then processed by host software, or to be transmitted on the network.
Revision 2.6 (12-04-08)
24
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Figure 3.1 VLAN Frame
3.3
Address Filtering Functional Description
The Ethernet address fields of an Ethernet Packet, consists of two 6-byte fields: one for the destination
address and one for the source address. The first bit of the destination address signifies whether it is
a physical address or a multicast address.
The LAN9221/LAN9221i address check logic filters the frame based on the Ethernet receive filter mode
that has been enabled. Filter modes are specified based on the state of the control bits in Table 3.1,
"Address Filtering Modes", which shows the various filtering modes used by the Ethernet MAC
Function. These bits are defined in more detail in the “MAC Control Register”. Please refer to Section
5.4.1, "MAC_CR—MAC Control Register" for more information on this register.
If the frame fails the filter, the Ethernet MAC function does not receive the packet. The host has the
option of accepting or ignoring the packet.
Table 3.1 Address Filtering Modes
MCPAS
PRMS
INVFILT
HO
HPFILT
DESCRIPTION
0
0
0
0
0
MAC address perfect filtering only
for all addresses.
0
0
0
0
1
MAC address perfect filtering for
physical address and hash filtering
for multicast addresses
SMSC LAN9221/LAN9221i
25
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 3.1 Address Filtering Modes (continued)
MCPAS
PRMS
INVFILT
HO
HPFILT
0
0
0
1
1
Hash Filtering for physical and
multicast addresses
0
0
1
0
0
Inverse Filtering
X
1
0
X
X
Promiscuous
1
0
0
0
X
Pass all multicast frames. Frames
with physical addresses are
perfect-filtered
1
0
0
1
1
Pass all multicast frames. Frames
with physical addresses are hashfiltered
3.4
Filtering Modes
3.4.1
Perfect Filtering
DESCRIPTION
This filtering mode passes only incoming frames whose destination address field exactly matches the
value programmed into the MAC Address High register and the MAC address low register. The MAC
address is formed by the concatenation of the above two registers in the MAC CSR Function.
3.4.2
Hash Only Filtering
This type of filtering checks for incoming Receive packets with either multicast or physical destination
addresses, and executes an imperfect address filtering against the hash table.
During imperfect hash filtering, the destination address in the incoming frame is passed through the
CRC logic and the upper six bits of the CRC register are used to index the contents of the hash table.
The hash table is formed by merging the register’s multicast hash table high and multicast hash table
low in the MAC CSR Function to form a 64-bit hash table. The most significant bit determines the
register to be used (High/Low), while the other five bits determine the bit within the register. A value
of 00000 selects Bit 0 of the multicast hash table low register and a value of 11111 selects Bit 31 of
the multicast hash table high register.
3.4.2.1
Hash Perfect Filtering
In hash perfect filtering, if the received frame is a physical address, the LAN9221/LAN9221i Packet
Filter block perfect-filters the incoming frame’s destination field with the value programmed into the
MAC Address High register and the MAC Address Low register. If the incoming frame is a multicast
frame, however, the LAN9221/LAN9221i packet filter function performs an imperfect address filtering
against the hash table.
The imperfect filtering against the hash table is the same imperfect filtering process described in the
“Hash Only Filtering” section above.
3.4.2.2
Inverse Filtering
In inverse filtering, thePacket Filter Block accepts incoming frames with a destination address not
matching the perfect address (i.e., the value programmed into the MAC Address High register and the
MAC Address Low register in the CRC block and rejects frames with destination addresses matching
the perfect address).
For all filtering modes, when the MCPAS bit is set, all multicast frames are accepted. When the PRMS
bit is set, all frames are accepted regardless of their destination address. This includes all broadcast
frames as well.
Revision 2.6 (12-04-08)
26
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.5
Wake-up Frame Detection
Setting the Wake-Up Frame Enable bit (WUEN) in the “WUCSR—Wake-up Control and Status
Register”, places the LAN9221/LAN9221i MAC in the wake-up frame detection mode. In this mode,
normal data reception is disabled, and detection logic within the MAC examines receive data for the
pre-programmed wake-up frame patterns. The LAN9221/LAN9221i can be programmed to notify the
host of the wake-up frame detection with the assertion of the host interrupt (IRQ) or assertion of the
power management event signal (PME). Upon detection, the Wake-Up Frame Received bit (WUFR) in
the WUCSR is set. When the host clears the WUEN bit the LAN9221/LAN9221i will resume normal
receive operation.
Before putting the MAC into the wake-up frame detection state, the host must provide the detection
logic with a list of sample frames and their corresponding byte masks. This information is written into
the Wake-up Frame Filter register (WUFF). Please refer to Section 5.4.11, "WUFF—Wake-up Frame
Filter," on page 116 for additional information on this register.
The MAC supports four programmable filters that support many different receive packet patterns. If
remote wake-up mode is enabled, the remote wake-up function receives all frames addressed to the
MAC. It then checks each frame against the enabled filter and recognizes the frame as a remote wakeup frame if it passes the wakeup frame filter register’s address filtering and CRC value match.
In order to determine which bytes of the frames should be checked by the CRC module, the MAC uses
a programmable byte mask and a programmable pattern offset for each of the four supported filters.
The pattern’s offset defines the location of the first byte that should be checked in the frame. Since
the destination address is checked by the address filtering Function, the pattern offset is always greater
than 12.
The byte mask is a 31-bit field that specifies whether or not each of the 31 contiguous bytes within
the frame, beginning in the pattern offset, should be checked. If bit j in the byte mask is set, the
detection logic checks byte offset +j in the frame. In order to load the Wake-up Frame Filter register,
the host LAN driver software must perform eight writes to the Wake-up Frame Filter register (WUFF).
The Diagram shown in Table 3.2, "Wake-Up Frame Filter Register Structure" below, shows the wakeup frame filter register’s structure.
Note 3.1
Wake-up frame detection can be performed when the LAN9221/LAN9221i is in the D0 or
D1 power states. In the D0 state, wake-up frame detection is enabled when the WUEN bit
is set.
Note 3.2
Wake-up frame detection, as well as Magic Packet detection, is always enabled and
cannot be disabled when the device enters the D1 state.
Note 3.3
When wake-up frame detection is enabled via the WUEN bit of the WUCSR—Wake-up
Control and Status Register, a broadcast wake-up frame will wake-up the device despite
the state of the Disable Broadcast Frame (BCAST) bit in the MAC_CR—MAC Control
Register.
SMSC LAN9221/LAN9221i
27
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 3.2 Wake-Up Frame Filter Register Structure
Filter 0 Byte Mask
Filter 1 Byte Mask
Filter 2 Byte Mask
Filter 3 Byte Mask
Reserved
Filter 3
Command
Reserved
Filter 3 Offset
Filter 2
Command
Reserved
Filter 2 Offset
Filter 1
Command
Filter 1Offset
Reserved
Filter 0
Command
Filter 0 Offset
Filter 1 CRC-16
Filter 0 CRC-16
Filter 3 CRC-16
Filter 2 CRC-16
The Filter i Byte Mask defines which incoming frame bytes Filter i will examine to determine whether
or not this is a wake-up frame. Table 3.3, describes the byte mask’s bit fields.
Table 3.3 Filter i Byte Mask Bit Definitions
FILTER I BYTE MASK DESCRIPTION
FIELD
31
30:0
DESCRIPTION
Must be zero (0)
Byte Mask: If bit j of the byte mask is set, the CRC machine processes byte number pattern - (offset
+ j) of the incoming frame. Otherwise, byte pattern - (offset + j) is ignored.
The Filter i command register controls Filter i operation. Table 3.4 shows the Filter I command register.
Table 3.4 Filter i Command Bit Definitions
FILTER i COMMANDS
FIELD
3
2:1
0
DESCRIPTION
Address Type: Defines the destination address type of the pattern. When bit is set, the pattern
applies
only to multicast frames. When bit is cleared, the pattern applies only to unicast frames.
RESERVED
Enable Filter: When bit is set, Filter i is enabled, otherwise, Filter i is disabled.
The Filter i Offset register defines the offset in the frame’s destination address field from which the
frames are examined by Filter i. Table 3.5 describes the Filter i Offset bit fields.
Revision 2.6 (12-04-08)
28
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 3.5 Filter i Offset Bit Definitions
FILTER I OFFSET DESCRIPTION
FIELD
7:0
DESCRIPTION
Pattern Offset: The offset of the first byte in the frame on which CRC is checked for wake-up frame
recognition. The minimum value of this field must be 12 since there should be no CRC check for
the destination address and the source address fields. The MAC checks the first offset byte of the
frame for CRC and checks to determine whether the frame is a wake-up frame. Offset 0 is the first
byte of the incoming frame's destination address.
The Filter i CRC-16 register contains the CRC-16 result of the frame that should pass Filter i.
Table 3.6 describes the Filter i CRC-16 bit fields.
Table 3.6 Filter i CRC-16 Bit Definitions
FILTER I CRC-16 DESCRIPTION
FIELD
15:0
3.5.1
DESCRIPTION
Pattern CRC-16: This field contains the 16-bit CRC value from the pattern and the byte mask
programmed to the wake-up filter register Function. This value is compared against the CRC
calculated on the incoming frame, and a match indicates the reception of a wakeup frame.
Magic Packet Detection
Setting the Magic Packet Enable bit (MPEN) in the “WUCSR—Wake-up Control and Status Register”,
places the LAN9221/LAN9221i MAC in the “Magic Packet” detection mode. In this mode, normal data
reception is disabled, and detection logic within the MAC examines receive data for a Magic Packet.
The LAN9221/LAN9221i can be programmed to notify the host of the “Magic Packet” detection with
the assertion of the host interrupt (IRQ) or assertion of the power management event signal (PME).
Upon detection, the Magic Packet Received bit (MPR) in the WUCSR is set. When the host clears the
MPEN bit the LAN9221/LAN9221i will resume normal receive operation. Please refer to Section 5.4.12,
"WUCSR—Wake-up Control and Status Register," on page 116 for additional information on this
register
In Magic Packet mode, the Power Management Logic constantly monitors each frame addressed to
the node for a specific Magic Packet pattern. It checks only packets with the MAC’s address or a
broadcast address to meet the Magic Packet requirement. The Power Management Logic checks each
received frame for the pattern 48h FF_FF_FF_FF_FF_FF after the destination and source address
field.
Then the Function looks in the frame for 16 repetitions of the MAC address without any breaks or
interruptions. In case of a break in the 16 address repetitions, the PMT Function scans for the
48'hFF_FF_FF_FF_FF_FF pattern again in the incoming frame.
The 16 repetitions may be anywhere in the frame but must be preceded by the synchronization stream.
The device will also accept a multicast frame, as long as it detects the 16 duplications of the MAC
address. If the MAC address of a node is 00h 11h 22h 33h 44h 55h, then the MAC scans for the
following data sequence in an Ethernet: Frame.
SMSC LAN9221/LAN9221i
29
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Destination Address Source Address ……………FF FF FF FF FF FF
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
…CRC
It should be noted that Magic Packet detection can be performed when LAN9221/LAN9221i is in the
D0 or D1 power states. In the D0 state, “Magic Packet” detection is enabled when the MPEN bit is
set. In the D1 state, Magic Packet detection, as well as wake-up frame detection, are automatically
enabled when the device enters the D1 state.
3.6
Checksum Offload Engines (COE)
The LAN9221/LAN9221i contains two checksum offload engines, which offload the calculation of the
16-bit checksum for transmitted and received Ethernet frames. The functionality of the checksum
offload engines is described in the following sections:
3.6.1
„
Receive Checksum Offload Engine (RXCOE)
„
Transmit Checksum Offload Engine (TXCOE)
Receive Checksum Offload Engine (RXCOE)
The receive checksum offload engine provides assistance to the CPU by calculating a 16-bit checksum
for a received Ethernet frame. The RXCOE readily supports the following IEEE802.3 frame formats:
„
Type II Ethernet frames
„
SNAP encapsulated frames
„
Support for up to 2, 802.1q VLAN tags
The resulting checksum value can also be modified by software to support other frame formats.
The RXCOE has two modes of operation. In mode 0, the RXCOE calculates the checksum between
the first 14 bytes of the Ethernet frame and the FCS. This is illustrated in Figure 3.4.
DST
SRC
T
Y
P
E
Frame Data
F
C
S
Calculate Checksum
Figure 3.4 RXCOE Checksum Calculation
In mode 1, the RXCOE supports VLAN tags and a SNAP header. In this mode the RXCOE calculates
the checksum at the start of L3 packet. The VLAN1 tag register is used by the RXCOE to indicate
what protocol type is to be used to indicate the existence of a VLAN tag. This value is typically 8100h.
Revision 2.6 (12-04-08)
30
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Example frame configurations:
DST
0
SRC
p
r
o
t
2
3
1
L3 Packet
F
C
S
Calculate Checksum
1DWORD
Figure 3.5 Type II Ethernet Frame
DST
0
SRC
1
2
8
t
V
1
y
I
0
p
D
0
e
3
L3 Packet
F
C
S
4
Calculate Checksum
1DWORD
Figure 3.6 Ethernet Frame with VLAN Tag
{DSAP, SSAP, CTRL, OUI[23:16]}
DST
0
SRC
1
2
S
L N
e A
n P
0
3
{OUI[15:0], PID[15:0]}
S
N
A
P
1
4
L3 Packet
F
C
S
5
Calculate Checksum
1DWORD
Figure 3.7 Ethernet Frame with Length Field and SNAP Header
SMSC LAN9221/LAN9221i
31
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
{DSAP, SSAP, CTRL,
OUI[23:16]}
DST
0
S
8
V L N
1
I e A
0
Dn P
0
0
SRC
1
2
3
4
{OUI[15:0], PID[15:0]}
S
N
A
P
1
5
F
C
S
L3 Packet
6
Calculate Checksum
1DWORD
Figure 3.8 Ethernet Frame with VLAN Tag and SNAP Header
{DSAP, SSAP, CTRL,
OUI[23:16]}
DST
0
SRC
1
2
S
8
8
V
V L N
1
1
I
I e A
0
0
D
Dn P
0
0
0
4
5
6
{OUI[15:0], PID[15:0]}
S
N
A
P
1
7
F
C
S
L3 Packet
8
Calculate Checksum
1DWORD
Figure 3.9 Ethernet Frame with multiple VLAN Tags and SNAP Header
The RXCOE supports a maximum of two VLAN tags. If there are more than two VLAN tags, the VLAN
protocol identifier for the third tag is treated as an Ethernet type field. The checksum calculation will
begin immediately after the type field.
The RXCOE resides in the RX path within the MAC. As the RXCOE receives an Ethernet frame it
calculates the 16-bit checksum. The RXCOE passes the Ethernet frame to the RX Data FIFO with the
checksum appended to the end of the frame. The RXCOE inserts the checksum immediately after the
last byte of the Ethernet frame. The packet length field in the RX status word (refer to Section 3.13.3)
will indicate that the frame size has increased by two bytes to accommodate the checksum.
Setting the RXCOE_EN bit in the COE_CR—Checksum Offload Engine Control Register enables the
RXCOE, while the RXCOE_MODE bit selects the operating mode. When the RXCOE is disabled, the
the received data is simply passed through the RXCOE unmodified.
Note: Software applications must stop the receiver and flush the RX data path before changing the
state of the RXCOE_EN or RXCOE_MODE bits.
Note: When the RXCOE is enabled, automatic pad stripping must be disabled (bit 8 (PADSTR) of
the MAC_CR—MAC Control Register) and vice versa. These functions cannot be enabled
simultaneously.
Revision 2.6 (12-04-08)
32
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.6.1.1
RX Checksum Calculation
The checksum is calculated 16 bits at a time. In the case of an odd sized frame, an extra byte of zero
is used to pad up to 16 bits.
Consider the following packet: DA, SA, Type, B0, B1, B2 … BN, FCS
Let [A, B] = A*256 + B;
If the packet has an even number of octets then
checksum = [B1, B0] + C0 + [B3, B2] + C1 + … + [BN, BN-1] + CN-1
Where C0, C1, ... CN-1 are the carry out results of the intermediate sums.
If the packet has an odd number of octets then
checksum = [B1, B0] + C0 + [B3, B2] + C1 + … + [0, BN] + CN-1
3.6.2
Transmit Checksum Offload Engine (TXCOE)
The transmit checksum offload engine provides assistance to the CPU by calculating a 16-bit
checksum, typically for TCP, for a transmit Ethernet frame. The TXCOE calculates the checksum and
inserts the results back into the data stream as it is transferred to the MAC.
To activate the TXCOE and perform a checksum calculation, the host must first set the TX checksum
offload engine enable bit (TXCOE_EN) in the COE_CR—Checksum Offload Engine Control Register.
The host then pre-pends a 3 DWORD buffer to the data that will be transmitted. The pre-pended buffer
includes a TX Command ‘A’, TX Command ‘B’, and a 32-bit TX checksum preamble. When bit 14 (CK)
of the TX Command ‘B’ is set in conjunction with bit 13 (FS) of TX Command ‘A’ and bit 16
(TXCOE_EN) of the COE_CR register, the TXCOE will perform a checksum calculation on the
associated packet. When these three bits are set, a 32-bit TX checksum preamble must be pre-pended
to the beginning of the TX packet (refer to Table 3.7). The TX checksum preamble instructs the TXCOE
on the handling of the associated packet. Bits 11:0 of the TX checksum preamble define the byte offset
at which the data checksum calculation will begin (TXCSSP). The checksum calculation will begin at
this offset and will continue until the end of the packet. The data checksum calculation must not begin
in the MAC header (first 14 bytes) or in the last 4 bytes of the TX packet. When the calculation is
complete, the checksum will be inserted into the packet at the byte offset defined by bits 27:16 of the
TX checksum preamble (TXCSLOC). The TX checksum cannot be inserted in the MAC header (first
14 bytes) or in the last 4 bytes of the TX packet. If the CK bit is not set in the first TX Command ‘B’
of a packet, the packet is passed directly through the TXCOE without modification, regardless if the
TXCOE_EN is set. An example of a TX packet with a pre-pended TX checksum preamble can be
found in Section 3.12.6.3, "TX Example 3". In this example the host writes the packet data to the
ethernet controller in four fragments, the first containing the TX Checksum Preamble. Figure 3.17
shows how these fragments are loaded into the TX Data FIFO. For more information on the TX
Command ‘A’ and TX Command ‘B’, refer to Section 3.12.2, "TX Command Format".
If the TX packet already includes a partial checksum calculation (perhaps inserted by an upper layer
protocol), this checksum can be included in the hardware checksum calculation by setting the TXCSSP
field in the TX checksum preamble to include the partial checksum. The partial checksum can be
replaced by the completed checksum calculation by setting the TXCSLOC pointer to point to the
location of the partial checksum.
SMSC LAN9221/LAN9221i
33
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 3.7 TX Checksum Preamble
FIELD
DESCRIPTION
31:28
RESERVED
27:16
TXCSLOC - TX Checksum Location
This field specifies the byte offset where the TX checksum will be inserted in the TX packet. The
checksum will replace two bytes of data starting at this offset.
Note:
15:12
11:0
The TX checksum cannot be inserted in the MAC header (first 14 bytes) or in the last 4
bytes of the TX packet.
RESERVED
TXCSSP - TX Checksum Start Pointer
This field indicates start offset, in bytes, where the checksum calculation will begin in the associated
TX packet.
Note:
The data checksum calculation must not begin in the MAC header (first 14 bytes) or in
the last 4 bytes of the TX packet.
Note: When the TXCOE is enabled, the third DWORD of the pre-pended packet is not transmitted.
However, 4 bytes must be added to the packet length field in TX Command ‘B’.
Note: The TX checksum preamble must be DWORD-aligned (i.e., the two least significant bits of the
Data Start Offset fields in TX Command “A” must be zero). Any valid buffer end alignment
setting can be used.
Note: Software applications must stop the transmitter and flush the TX data path before changing the
state of the TXCOE_EN bit. However, the CK bit of TX Command ‘B’ can be set or cleared on
a per-packet basis.
3.6.2.1
TX Checksum Calculation
The TX checksum calculation is performed using the same operation as the RX checksum shown in
Section 3.6.1.1, with the exception that the calculation starts as indicated by the preamble, and the
transmitted checksum is the one’s-compliment of the final calculation.
3.7
Host Bus Operations
3.7.1
Bus Writes
The host processor is required to perform two contiguous 16-bit writes to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit write). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next write is performed to the other word. If a write to the
same word is performed, the LAN9221/LAN9221i disregards the transfer.
3.7.2
Bus Reads
The host processor is required to perform two consecutive 16-bit reads to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit read). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next read is performed from the other word. If a read to the
same word is performed, the data read is invalid and should be re-read. This is not a fatal error. The
LAN9221/LAN9221i will reset its read counters and restart a new cycle on the next read.
Revision 2.6 (12-04-08)
34
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.7.3
Mixed Endian Support
In order to allow flexibility with a range of designs, theLAN9221/LAN9221i supports mixed endian Data
FIFO accesses. The LAN9221/LAN9221i provides the ability to select Data FIFO endianess separately
for accesses through the Data FIFO ports (addresses 00h-3Ch) or using the FIFO_SEL input signal.
This is accomplished via the FPORTEND and FSELEND bits of the HW_CFG—Hardware
Configuration Register, respectively.
The FPORTEND bit determines the endianess of RX and TX Data FIFO host accesses made through
the Data FIFO port addresses (00h-3Ch). When FPORTEND is cleared, Data FIFO port accesses
utilize little endian byte ordering. When FPORTEND is set, Data FIFO port accesses utilize big endian
byte ordering.
The FSELEND bit determines the endianess of RX and TX Data FIFO host accesses when using the
FIFO_SEL signal. When FSELEND is cleared, FIFO_SEL accesses utilize little endian byte ordering.
When FSELEND is set, FIFO_SEL accesses utilize big endian byte ordering.
In addition to mixed endian support, the LAN9221/LAN9221i provides a word swap function, as
described in Section 3.7.4. The word swap function combined with the endianess select bits described
above determines how the Data/Status FIFO’s and CSR host access byte ordering is applied. Table 3.8
describes the various operation modes of the endianess and word swap ordering logic. Figure 3.3
illustrates the FIFO access byte ordering under various endianess and word swap settings. Refer to
Section 3.7.4 for additional details.
Note: CSR and status FIFO accesses are not affected by the FPORTEND and FSELEND endianess
select bits.
3.7.4
Word Swap Function
In addition to mixed endian functionality, the LAN9221/LAN9221i supports a Word Swap Function. This
feature is controlled by the Word Swap Register, which is described in Section 5.3.17,
"WORD_SWAP—Word Swap Control," on page 98. This register affects how words on the data bus
are written to or read from the Control and Status Registers and the Transmit and Receive Data/Status
FIFOs.
Both the word swap function and the mixed endian control bits contain the ability to change the byte
ordering of host data path accesses. Figure 3.2 illustrates the order in which the word swap and
endianess select logic is applied within the LAN9221/LAN9221i. Logically, the endian control logic is
applied after the word swap logic for write operations, and before the word swap logic for read
operations.
SMSC LAN9221/LAN9221i
35
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
C SR s and Status FIFO s
FPO R TEN D
(H W _C FG [29])
W O R D _SW A P
R X/TX D ata FIFO Port
A ccess (addresses 00h to
3C h)
R X/TX D ata FIFO D irect
A ccess
(FIFO _SEL = 1)
FIFO Port Endian O rdering
Logic
D irect FIFO A ccess Endian
O rdering Logic
FSELEN D
(H W _C FG [28])
"W O R D SW A P"
Logic
D [15:0]
(H ost D ata B us)
Figure 3.2 LAN9221/LAN9221i Host Data Path Diagram
Data path operations for the various supported endianess and word swap configurations are illustrated
in Figure 3.3. Table 3.8, "Endian Ordering Logic Operation" illustrates the byte ordering applied by the
endian logic for each type of host access. This figure and table assume an internal byte ordering of 32-1-0, where ‘3’ is the most significant byte (data[31:24]) and ‘0’ is the least significant byte (data[7:0]).
Revision 2.6 (12-04-08)
36
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
WORD_SWAP != FFFF_FFFFh
BIG ENDIAN
LITTLE ENDIAN
(FPORTEND = 1 for Data FIFO port access on addresses 00h-3Ch)
AND/OR (FSELEND = 1 for Data FIFO direct access when FIFO_SEL=1)
(FPORTEND = 0 for Data FIFO port access on addresses 00h-3Ch)
AND/OR (FSELEND = 0 for Data FIFO direct access when FIFO_SEL=1)
INTERNAL FIFO ORDER
INTERNAL FIFO ORDER
MSB
31
MSB
LSB
24
23
3
16
15
8
2
1
A[1] = 1
0
1
A[1] = 0
2
3
15
8
7
31
0
23
16
3
0
7
LSB
24
15
8
2
1
A[1] = 1
3
2
A[1] = 0
1
0
15
0
8
HOST DATA BUS
7
0
0
7
0
HOST DATA BUS
WORD_SWAP = FFFF_FFFFh
BIG ENDIAN
LITTLE ENDIAN
(FPORTEND = 1 for Data FIFO port access on addresses 00h-3Ch)
AND/OR (FSELEND = 1 for Data FIFO direct access when FIFO_SEL=1)
(FPORTEND = 0 for Data FIFO port access on addresses 00h-3Ch)
AND/OR (FSELEND = 0 for Data FIFO direct access when FIFO_SEL=1)
INTERNAL FIFO ORDER
INTERNAL FIFO ORDER
MSB
31
MSB
LSB
24
23
3
16
15
8
2
1
A[1] = 1
2
3
A[1] = 0
0
1
15
8
7
31
0
23
3
0
7
LSB
24
15
8
2
1
A[1] = 1
1
0
A[1] = 0
3
2
15
0
16
HOST DATA BUS
8
7
7
0
0
0
HOST DATA BUS
Figure 3.3 FIFO Access Byte Ordering
SMSC LAN9221/LAN9221i
37
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
WORD_SWAP = FFFF_FFFFh
WORD_SWAP != FFFF_FFFFh
Table 3.8 Endian Ordering Logic Operation
3.8
FIFO Access via Data
FIFO Port (00h-3Ch)
Direct FIFO Access via
FIFO_SEL
CSR Access
Host Data Bus
Host Data Bus
Host Data Bus
D[15:8]
D[7:0]
D[15:8]
D[7:0]
D[15:8]
D[7:0]
FPORTEND=0
FSELEND=0
A1=1
3
2
3
2
3
2
A1=0
1
0
1
0
1
0
FPORTEND=1
FSELEND=0
A1=1
0
1
3
2
3
2
A1=0
2
3
1
0
1
0
FPORTEND=0
FSELEND=1
A1=1
3
2
0
1
3
2
A1=0
1
0
2
3
1
0
A1=1
0
1
0
1
3
2
A1=0
2
3
2
3
1
0
FPORTEND=0
FSELEND=0
A1=1
1
0
1
0
1
0
A1=0
3
2
3
2
3
2
FPORTEND=1
FSELEND=0
A1=1
2
3
1
0
1
0
A1=0
0
1
3
2
3
2
PORTEND=0
FSELEND=1
A1=1
1
0
2
3
1
0
A1=0
3
2
0
1
3
2
A1=1
2
3
2
3
1
0
A1=0
0
1
0
1
3
2
FPORTEND=1
FSELEND=1
PORTEND=1
FSELEND=1
General Purpose Timer (GP Timer)
The General Purpose Timer is a programmable block that can be used to generate periodic host
interrupts. The resolution of this timer is 100uS.
The GP Timer loads the GPT_CNT Register with the value in the GPT_LOAD field and begins counting
down when the TIMER_EN bit is set to a ‘1.’ On a reset, or when the TIMER_EN bit changes from
set ‘1’ to cleared ‘0,’ the GPT_LOAD field is initialized to FFFFh. The GPT_CNT register is also
initialized to FFFFh on a reset. Software can write the pre-load value into the GPT_LOAD field at any
time; e.g., before or after the TIMER_EN bit is asserted. The GPT Enable bit TIMER_EN is located in
the GPT_CFG register.
Once enabled, the GPT counts down either until it reaches 0000h or until a new pre-load value is
written to the GPT_LOAD field. At 0000h, the counter wraps around to FFFFh, asserts the GPT
interrupt status bit and the IRQ signal if the GPT_INT_EN bit is set, and continues counting. The GPT
interrupt status bit is in the INT_STS Register. The GPT_INT hardware interrupt can only be set if the
GPT_INT_EN bit is set. GPT_INT is a sticky bit (R/WC); i.e., once the GPT_INT bit is set, it can only
be cleared by writing a ‘1’ to the bit.
Revision 2.6 (12-04-08)
38
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.9
EEPROM Interface
The LAN9221/LAN9221i can optionally load its MAC address from an external serial EEPROM. If a
properly configured EEPROM is detected by the LAN9221/LAN9221i at power-up, hard reset or soft
reset, the ADDRH and ADDRL registers will be loaded with the contents of the EEPROM. If a properly
configured EEPROM is not detected, it is the responsibility of the host LAN Driver to set the IEEE
addresses.
The LAN9221/LAN9221i EEPROM controller also allows the host system to read, write and erase the
contents of the Serial EEPROM. The EEPROM controller supports most “93C46” type EEPROMs
configured for 128 x 8-bit operation.
3.9.1
MAC Address Auto-Load
On power-up, hard reset or soft reset, the EEPROM controller attempts to read the first byte of data
from the EEPROM (address 00h). If the value A5h is read from the first address, then the EEPROM
controller will assume that an external Serial EEPROM is present. The EEPROM controller will then
access the next EEPROM byte and send it to the MAC Address register byte 0 (ADDRL[7:0]). This
process will be repeated for the next five bytes of the MAC Address, thus fully programming the 48bit MAC address. Once all six bytes have been programmed, the “MAC Address Loaded” bit is set in
the E2P_CMD register. A detailed explanation of the EEPROM byte ordering with respect to the MAC
address is given in Section 5.4.3, "ADDRL—MAC Address Low Register," on page 111.
If an 0xA5h is not read from the first address, the EEPROM controller will end initialization. It is then
the responsibility of the host LAN driver software to set the IEEE address by writing to the MAC’s
ADDRH and ADDRL registers.
The host can initiate a reload of the MAC address from the EEPROM by issuing the RELOAD
command via the E2P command (E2P_CMD) register. If the first byte read from the EEPROM is not
A5h, it is assumed that the EEPROM is not present, or not programmed, and the MAC address reload
will fail. The “MAC Address Loaded” bit indicates a successful reload of the MAC address.
3.9.2
EEPROM Host Operations
After the EEPROM controller has finished reading (or attempting to read) the MAC after power-on, hard
reset or soft reset, the host is free to perform other EEPROM operations. EEPROM operations are
performed using the E2P_CMD and E2P data (E2P_DATA) registers. Section 5.3.23, "E2P_CMD –
EEPROM Command Register," on page 103 provides an explanation of the supported EEPROM
operations.
If the EEPROM operation is the “write location” (WRITE) or “write all” (WRAL) commands, the host
must first write the desired data into the E2P_DATA register. The host must then issue the WRITE or
WRAL command using the E2P_CMD register by setting the EPC_CMD field appropriately. If the
operation is a WRITE, the EPC_ADDR field in E2P_CMD must also be set to the desired location. The
command is executed when the host sets the EPC_BSY bit high. The completion of the operation is
indicated when the EPC_BSY bit is cleared.
If the EEPROM operation is the “read location” (READ) operation, the host must issue the READ
command using the E2P_CMD with the EPC_ADDR set to the desired location. The command is
executed when the host sets the EPC_BSY bit high. The completion of the operation is indicated when
the EPC_BSY bit is cleared, at which time the data from the EEPROM may be read from the
E2P_DATA register.
Other EEPROM operations are performed by writing the appropriate command to the EPC_CMD
register. The command is executed when the host sets the EPC_BSY bit high. The completion of the
operation is indicated when the EPC_BSY bit is cleared. In all cases the host must wait for EPC_BSY
to clear before modifying the E2P_CMD register.
Note: The EEPROM device powers-up in the erase/write disabled state. To modify the contents of
the EEPROM the host must first issue the EWEN command.
SMSC LAN9221/LAN9221i
39
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
If an operation is attempted, and an EEPROM device does not respond within 30mS, the
LAN9221/LAN9221i will timeout, and the EPC timeout bit (EPC_TO) in the E2P_CMD register will be
set.
Figure 3.4, "EEPROM Access Flow Diagram" illustrates the host accesses required to perform an
EEPROM Read or Write operation.
EEPROM Write
EEPROM Read
Idle
Idle
Write Data
Register
Write
Command
Register
Write
Command
Register
Read
Command
Register
Busy Bit = 0
Busy Bit = 0
Read
Command
Register
Read Data
Register
Figure 3.4 EEPROM Access Flow Diagram
The host can disable the EEPROM interface through the GPIO_CFG register. When the interface is
disabled, the EEDIO and ECLK signals can be used as general-purpose outputs, or they may be used
to monitor internal MII signals.
3.9.2.1
Supported EEPROM Operations
The EEPROM controller supports the following EEPROM operations under host control via the
E2P_CMD register. The operations are commonly supported by “93C46” EEPROM devices. A
description and functional timing diagram is provided below for each operation. Please refer to the
E2P_CMD register description in Section 5.3.23, "E2P_CMD – EEPROM Command Register," on
page 103 for E2P_CMD field settings for each command.
Revision 2.6 (12-04-08)
40
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
ERASE (Erase Location): If erase/write operations are enabled in the EEPROM, this command will
erase the location selected by the EPC Address field (EPC_ADDR). The EPC_TO bit is set if the
EEPROM does not respond within 30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
1
1
A6
A0
EEDIO (INPUT)
Figure 3.5 EEPROM ERASE Cycle
ERAL (Erase All): If erase/write operations are enabled in the EEPROM, this command will initiate a
bulk erase of the entire EEPROM.The EPC_TO bit is set if the EEPROM does not respond within
30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
1
0
EEDIO (INPUT)
Figure 3.6 EEPROM ERAL Cycle
SMSC LAN9221/LAN9221i
41
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
EWDS (Erase/Write Disable): After issued, the EEPROM will ignore erase and write commands. To
re-enable erase/write operations issue the EWEN command.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
0
0
EEDIO (INPUT)
Figure 3.7 EEPROM EWDS Cycle
EWEN (Erase/Write Enable): Enables the EEPROM for erase and write operations. The EEPROM
will allow erase and write operations until the “Erase/Write Disable” command is sent, or until power
is cycled.
Note: The EEPROM device will power-up in the erase/write-disabled state. Any erase or write
operations will fail until an Erase/Write Enable command is issued.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
1
1
EEDIO (INPUT)
Figure 3.8 EEPROM EWEN Cycle
Revision 2.6 (12-04-08)
42
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
READ (Read Location): This command will cause a read of the EEPROM location pointed to by EPC
Address (EPC_ADDR). The result of the read is available in the E2P_DATA register.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
1
0
A6
A0
EEDIO (INPUT)
D7
D0
Figure 3.9 EEPROM READ Cycle
WRITE (Write Location): If erase/write operations are enabled in the EEPROM, this command will
cause the contents of the E2P_DATA register to be written to the EEPROM location selected by the
EPC Address field (EPC_ADDR). The EPC_TO bit is set if the EEPROM does not respond within
30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
1
A6
A0
D7
D0
EEDIO (INPUT)
Figure 3.10 EEPROM WRITE Cycle
WRAL (Write All): If erase/write operations are enabled in the EEPROM, this command will cause the
contents of the E2P_DATA register to be written to every EEPROM memory location. The EPC_TO bit
is set if the EEPROM does not respond within 30ms.
tCSL
EECS
EECLK
EEDIO (OUTPUT)
1
0
0
0
D7
1
D0
EEDIO (INPUT)
Figure 3.11 EEPROM WRAL Cycle
Table 3.9, "Required EECLK Cycles", shown below, shows the number of EECLK cycles required for
each EEPROM operation.
SMSC LAN9221/LAN9221i
43
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 3.9 Required EECLK Cycles
3.9.2.2
OPERATION
REQUIRED EECLK CYCLES
ERASE
10
ERAL
10
EWDS
10
EWEN
10
READ
18
WRITE
18
WRAL
18
MAC Address Reload
The MAC address can be reloaded from the EEPROM via a host command to the E2P_CMD register.
If a value of 0xA5h is not found in the first address of the EEPROM, the EEPROM is assumed to be
un-programmed and MAC Address Reload operation will fail. The “MAC Address Loaded” bit indicates
a successful load of the MAC address. The EPC_LOAD bit is set after a successful reload of the MAC
address.
3.9.2.3
EEPROM Command and Data Registers
Refer to Section 5.3.23, "E2P_CMD – EEPROM Command Register," on page 103 and Section 5.3.24,
"E2P_DATA – EEPROM Data Register," on page 105 for a detailed description of these registers.
Supported EEPROM operations are described in these sections.
3.9.2.4
EEPROM Timing
Refer to Section 6.10, "EEPROM Timing," on page 138 for detailed EEPROM timing specifications.
3.10
Power Management
The LAN9221/LAN9221i supports power-down modes to allow applications to minimize power
consumption. The following sections describe these modes.
3.10.1
System Description
Power is reduced to various modules by disabling the clocks as outlined in Table 3.10, “Power
Management States,” on page 46. All configuration data is saved when in either of the two low power
states. Register contents are not affected unless specifically indicated in the register description.
3.10.2
Functional Description
There is one normal operating power state, D0 and there are two power saving states: D1, and D2.
Upon entry into either of the two power saving states, only the PMT_CTRL register is accessible for
read operations. In either of the power saving states the READY bit in the PMT_CTRL register will be
cleared. Reads of any other addresses are forbidden until the READY bit is set. All writes, with the
exception of the wakeup write to BYTE_TEST, are also forbidden until the READY bit is set. Only when
in the D0 (Normal) state, when the READY bit is set, can the rest of the device be accessed.
Revision 2.6 (12-04-08)
44
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Note 3.10 The LAN9221/LAN9221i must always be read at least once after power-up, reset, or upon
return from a power-saving state, otherwise write operations will not function.
In system configurations where the PME signal is shared amongst multiple devices, the WUPS field
within the PMT_CTRL register can be read to determine which LAN9221/LAN9221i device is driving
the PME signal.
When the LAN9221/LAN9221i is in a power saving state (D1 or D2), a write cycle to the BYTE_TEST
register will return the LAN9221/LAN9221i to the D0 state. Table 7.2, “Power Consumption Device and
System Components,” on page 141 and Table 7.2, “Power Consumption Device and System
Components,” on page 141, shows the power consumption values for each power state.
Note 3.11 When the LAN9221/LAN9221i is in a power saving state, a write of any data to the
BYTE_TEST register will wake-up the device. DO NOT PERFORM WRITES TO OTHER
ADDRRESSES while the READY bit in the PMT_CTRL register is cleared.
3.10.2.1
D1 Sleep
Power consumption is reduced in this state by disabling clocks to portions of the internal logic as
shown in Table 3.10. In this mode the clock to the internal PHY and portions of the MAC are still
operational. This state is entered when the host writes a '01' to the PM_MODE bits in the Power
Management (PMT_CTRL) register. The READY bit in PMT_CTRL is cleared when entering the D1
state.
Wake-up frame and Magic Packet detection are automatically enabled in the D1 state. If properly
enabled via the WOL_EN and PME_EN bits, the LAN9221/LAN9221i will assert the PME hardware
signal upon the detection of the wake-up frame or magic packet. The LAN9221/LAN9221i can also
assert the host interrupt (IRQ) on detection of a wake-up frame or magic packet. Upon detection, the
WUPS field in PMT_CTRL will be set to a 10b.
Note 3.12 The PME interrupt status bit (PME_INT) in the INT_STS register is set regardless of the
setting of PME_EN.
Note 3.13 Wake-up frame and Magic Packet detection is automatically enabled when entering the D1
state. For wake-up frame detection, the wake-up frame filter must be programmed before
entering the D1 state (see Section 3.5, "Wake-up Frame Detection," on page 27). If used,
the host interrupt and PME signal must be enabled prior to entering the D1 state.
A write to the BYTE_TEST register, regardless of whether a wake-up frame or Magic Packet was
detected, will return LAN9221/LAN9221i to the D0 state and will reset the PM_MODE field to the D0
state. As noted above, the host is required to check the READY bit and verify that it is set before
attempting any other reads or writes of the device.
Note 3.14 The host must only perform read accesses prior to the ready bit being set.
Once the READY bit is set, the LAN9221/LAN9221i is ready to resume normal operation. At this time
the WUPS field can be cleared.
3.10.2.2
D2 Sleep
In this state, as shown in Table 3.10, all clocks to the MAC and host bus are disabled and the PHY is
placed in a reduced power state. To enter this state, the EDPWRDOWN bit in register 17 of the PHY
(Mode Control/Status register) must be set. This places the PHY in the Energy Detect mode. The
PM_MODE bits in the PMT_CTRL register must then be set to 10b. Upon setting the PM_MODE bits,
the LAN9221/LAN9221i will enter the D2 sleep state. The READY bit in PMT_CTRL is cleared when
entering the D2 state.
Note 3.15 If carrier is present when this state is entered detection will occur immediately.
If properly enabled via the ED_EN and PME_EN bits, the LAN9221/LAN9221i will assert the PME
hardware signal upon detection of a valid carrier. Upon detection, the WUPS field in PMT_CTRL will
be set to a 01b.
SMSC LAN9221/LAN9221i
45
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Note 3.16 The PME interrupt status bit on the INT_STS register (PME_INT) is set regardless of the
setting of PME_EN.
A write to the BYTE_TEST register, regardless of whether a carrier was detected, will return the
LAN9221/LAN9221i to the D0 state and will reset the PM_MODE field to the D0 state. As noted above,
the host is required to check the READY bit and verify that it is set before attempting any other reads
or writes of the device. Before the LAN9221/LAN9221i is fully awake from this state the EDPWRDOWN
bit in register 17 of the PHY must be cleared in order to wake the PHY. Do not attempt to clear the
EDPWRDOWN bit until the READY bit is set. After clearing the EDPWRDOWN bit the
LAN9221/LAN9221i is ready to resume normal operation. At this time the WUPS field can be cleared.
Table 3.10 Power Management States
Device
BLOCK
D0
(NORMAL OPERATION)
D1
(WOL)
D2
(ENERGY DETECT)
PHY
Full ON
Full ON
Energy Detect Power-Down
MAC Power
Management
Full ON
RX Power Mgmt. Block
On
OFF
MAC and Host
Interface
Full ON
OFF
OFF
Internal Clock
Full ON
Full ON
OFF
KEY
CLOCK ON
BLOCK DISABLED – CLOCK ON
FULL OFF
Revision 2.6 (12-04-08)
46
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.10.2.3
Power Management Event Indicators
Figure 3.12 is a simplified block diagram of the logic that controls the external PME, and internal
pme_interrupt signals. The pme_interrupt signal is used to set the PME_INT status bit in the INT_STS
register, which, if enabled, will generate a host interrupt upon detection of a power management event.
The PME_INT status bit in INT_STS will remain set until the internal pme_interrupt signal is cleared
by clearing the WUPS bits, or by clearing the corresponding WOL_EN or ED_EN bit. After clearing the
internal pme_interrupt signal, the PME_INT status bit may be cleared by writing a ‘1’ to this bit in the
INT_STS register. It should be noted that the LAN9221/LAN9221i can generate a host interrupt
regardless of the state of the PME_EN bit, or the external PME signal.
The external PME signal can be setup for pulsed, or static operation. When the PME_IND bit in the
PMT_CTRL register is set to a ‘1’, the external PME signal will be driven active for 50ms upon
detection of a wake-up event. When the PME_IND bit is cleared, the PME signal will be driven
continuously upon detection of a wake-up event. The PME signal is deactivated by clearing the WUPS
bits, or by clearing the corresponding WOL_EN or ED_EN bit. The PME signal can also be deactivated
by clearing the PME_EN bit.
WUFR
WOL_EN
WUEN
WUPS
MPR
ED_EN
MPEN
WUPS
phy_int
Other System
Interrupts
PME_INT
IRQ
Denotes a level-triggered "sticky" status bit
PME_INT_EN
IRQ_EN
50ms
PME_EN
PME
LOGIC
PME_IND
PME_POL
PME_TYPE
Figure 3.12 PME and PME_INT Signal Generation
3.10.3
Internal PHY Power-Down Modes
There are 2 power-down modes for the internal PHY:
3.10.3.1
General Power-Down
This power-down is controlled by register 0, bit 11. In this mode the internal PHY, except the
management interface, is powered-down and stays in that condition as long as Phy register bit 0.11 is
HIGH. When bit 0.11 is cleared, the PHY powers up and is automatically reset. Please refer to Section
5.5.1, "Basic Control Register," on page 119 for additional information on this register.
SMSC LAN9221/LAN9221i
47
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.10.3.2
Energy Detect Power-Down
This power-down mode is activated by setting the Phy register bit 17.13 to 1. Please refer to Section
5.5.8, "Mode Control/Status," on page 123 for additional information on this register. In this mode when
no energy is present on the line, the PHY is powered down, with the exception of the management
interface, the SQUELCH circuit and the ENERGYON logic. The ENERGYON logic is used to detect
the presence of valid energy from 100Base-TX, 10Base-T, or Auto-negotiation signals
In this mode, when the ENERGYON signal is low, the PHY is powered-down, and nothing is
transmitted. When energy is received - link pulses or packets - the ENERGYON signal goes high, and
the PHY powers-up. It automatically resets itself into the state it had prior to power-down, and asserts
the INT7.1 bit of the register defined in Section 5.5.11, "Interrupt Source Flag," on page 126. If the
ENERGYON interrupt is enabled, this event will cause an interrupt to the host. The first and possibly
the second packet to activate ENERGYON may be lost. When 17.13 is low, energy detect power-down
is disabled.
3.11
Detailed Reset Description
The LAN9221/LAN9221i has four reset sources:
„
Hardware Reset Input Pin (nRESET)
„
Soft Reset (SRST)
„
PHY Soft Reset via PMT_CTRL bit 10 (PHY_RST)
„
PHY Soft Reset via PHY Basic Control Register (PHY REG 0.15)
Table 3.11 shows the effect of the various reset sources on the LAN9221/LAN9221i's circuitry.
Note: For proper operation, the LAN9221/LAN9221i must be reset on power-up via the hardware
reset input (nRESET) or soft reset (SRST). To accomplish this, nRESET should be asserted
for the minimum period of 30ms at power-up. Alternatively, a soft reset may be performed
following power-up by setting the SRST bit of the HW_CFG register once the READY bit in the
PMT_CTRL register has been set. Refer to Section 3.11.1, "Hardware Reset Input (nRESET)"
and Section 3.11.3, "Soft Reset (SRST)" for additional information.
Table 3.11 Reset Sources and Affected Circuitry
RESET
SOURCE
nRESET
SRST
MAC
PHY
Note 3.17
EEPROM MAC
ADDR.
RELOAD
Note 3.18
CONFIG.
STRAPS
LATCHED
X
X
X
X
X
X
X
PLL
HBI
Note
3.19
NASR
REGISTERS
Note 3.19
MIL
X
X
X
X
X
PHY_RST
X
PHY REG 0.15
X
Note 3.17 After any PHY reset, the application must wait until the “Link Status” bit in the PHY’s “Basic
Status Register” (PHY Reg. 1.2) is set before attempting to transmit or receive data.
Note 3.18 After a power-up, nRESET or SRST, the LAN9221/LAN9221i will automatically check for
the presence of an external EEPROM. After any of these resets the application must verify
that the EPC Busy Bit (E2P_CMD, bit 31) is cleared before attempting to access the
EEPROM, or change the function of the GPO/GPIO signals, or before modifying the
ADDRH or ADDRL registers in the MAC.
Note 3.19 HBI - “Host Bus Interface”, NASR - Not affected by software reset.
Revision 2.6 (12-04-08)
48
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) after an internal
reset (22ms). If the software driver polls this bit and it is not set within 100ms, then an error
condition occurred.
3.11.1
Hardware Reset Input (nRESET)
A hardware reset will occur when the nRESET input signal is driven low. The READY bit in the
PMT_CTRL register can be read from the host interface, and will read back a ‘0’ until the hardware
reset is complete. Upon completion of the hardware reset, the READY bit in PMT_CTRL is set high.
After the “READY” bit is set, the LAN9221/LAN9221i can be configured via its control registers. The
nRESET signal is pulled-high internally by the LAN9221/LAN9221i and can be left unconnected if
unused. If used, nRESET must be driven low for a minimum period as defined in Section 6.9, "Reset
Timing," on page 137. If nRESET is unused, the device must be reset following power-up via a soft
reset (SRST).
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) immediately. If
the software driver polls this bit and it is not set within 100ms, then an error condition
occurred.
3.11.2
Resume Reset Timing
After issuing a write to the BYTE_TEST register to wake the LAN9221/LAN9221i from a power-down
state, the READY bit in PMT_CTRL will assert (set High) within 2ms.
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) within 2 ms. If
the software driver polls this bit and it is not set within 100ms, then an error condition
occurred.
3.11.3
Soft Reset (SRST)
Soft reset is initiated by writing a ‘1’ to bit 0 of the HW_CFG register (SRST). This self-clearing bit will
return to ‘0’ after approximately 2 μs, at which time the Soft Reset is complete. Soft reset does not
clear control register bits marked as NASR. Following power-on, a soft reset must not be performed
until the READY bit in the PMT_CTRL register has been set.
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) immediately,
(within 2μs). If the software driver polls this bit and it is not set within 100ms, then an error
condition occurred.
3.11.4
PHY Reset Timing
The following sections specify the operation and time required for the internal PHY to become
operational after various resets or when returning from the reduced power state.
3.11.4.1
PHY Soft Reset via PMT_CTRL bit 10 (PHY_RST)
The PHY soft reset is initiated by writing a ‘1’ to bit 10 of the PMT_CTRL register (PHY_RST). This
self-clearing bit will return to ‘0’ after approximately 100 μs, at which time the PHY reset is complete.
3.11.4.2
PHY Soft Reset via PHY Basic Control Register (PHY Reg. 0.15)
The PHY Reg. 0.15 Soft Reset is initiated by writing a ‘1’ to bit 15 of the PHY’s Basic Control Register.
This self-clearing bit will return to ‘0’ at which time the PHY reset is complete.
SMSC LAN9221/LAN9221i
49
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.12
TX Data Path Operation
Data is queued for transmission by writing it into the TX data FIFO. Each packet to be transmitted may
be divided among multiple buffers. Each buffer starts with a two DWORD TX command (TX command
‘A’ and TX command ‘B’). The TX command instructs the LAN9221/LAN9221i on the handling of the
associated buffer. Packet boundaries are delineated using control bits within the TX command.
The host provides a 16-bit Packet Tag field in the TX command. The Packet Tag value is appended
to the corresponding TX status DWORD. All Packet Tag fields must have the same value for all buffers
in a given packet. If tags differ between buffers in the same packet the TXE error will be asserted. Any
value may be chosen for a Packet Tag as long as all tags in the same Packet are identical. Packet
Tags also provide a method of synchronization between transmitted packets and their associated
status. Software can use unique Packet Tags to assist with validating matching status completions.
Note 3.20 The use of packet tags is not required by the hardware. This is a software LAN driver only
application example for use of this field.
A Packet Length field in the TX command specifies the number of bytes in the associated packet. All
Packet Length fields must have the same value for all buffers in a given packet. Hardware compares
the Packet Length field and the actual amount of data received by the Ethernet controller. If the actual
packet length count does not match the Packet Length field as defined in the TX command, the
Transmitter Error (TXE) flag is asserted.
The LAN9221/LAN9221i can be programmed to start payload transmission of a buffer on a byte
boundary by setting the “Data Start Offset” field in the TX command. The “Data Start Offset” field points
to the actual start of the payload data within the first 8 DWORDs of the buffer. Data before the “Data
Start Offset” pointer will be ignored. When a packet is split into multiple buffers, each successive buffer
may begin on any arbitrary byte.
The LAN9221/LAN9221i can be programmed to strip padding from the end of a transmit packet in the
event that the end of the packet does not align with the host burst boundary. This feature is necessary
when the LAN9221/LAN9221i is operating in a system that always performs multi-word bursts. In such
cases the LAN9221/LAN9221i must guarantee that it can accept data in multiples of the Burst length
regardless of the actual packet length. When configured to do so, the LAN9221/LAN9221i will accept
extra data at the end of the packet and will remove the extra padding before transmitting the packet.
The LAN9221/LAN9221i automatically removes data up to the boundary specified in the Buffer End
Alignment field specified in each TX command.
The host can instruct the LAN9221/LAN9221i to issue an interrupt when the buffer has been fully
loaded into the TX FIFO contained in the LAN9221/LAN9221i and transmitted. This feature is enabled
through the TX command ‘Interrupt on Completion’ field.
Upon completion of transmission, irrespective of success or failure, the status of the transmission is
written to the TX status FIFO. TX status is available to the host and may be read using PIO operations.
An interrupt can be optionally enabled by the host to indicate the availability of a programmable
number TX status DWORDS.
Before writing the TX command and payload data to the TX FIFO, the host must check the available
TX FIFO space by performing a PIO read of the TX_FIFO_INF register. The host must ensure that it
does not overfill the TX FIFO or the TX Error (TXE) flag will be asserted.
The host proceeds to write the TX command by first writing TX command ‘A’, then TX command ‘B’.
After writing the command, the host can then move the payload data into the TX FIFO. TX status
DWORD’s are stored in the TX status FIFO to be read by the host at a later time upon completion of
the data transmission onto the wire.
Revision 2.6 (12-04-08)
50
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
init
Idle
TX Status
Available
Check
available
FIFO
space
Read TX
Status
(optional)
Write
TX
Command
Write
Start
Padding
(optional)
Last Buffer in
Packet
Not Last Buffer
Write
Buffer
Figure 3.13 Simplified Host TX Flow Diagram
3.12.1
TX Buffer Format
TX buffers exist in the host’s memory in a given format. The host writes a TX command word into the
TX data buffer before moving the Ethernet packet data. The TX command A and command B are 32bit values that are used by the LAN9221/LAN9221i in the handling and processing of the associated
Ethernet packet data buffer. Buffer alignment, segmentation and other packet processing parameters
are included in the command structure. The following diagram illustrates the buffer format.
SMSC LAN9221/LAN9221i
51
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Host Write
31
Order
0
1st
TX Command 'A'
2nd
TX Command 'B'
3rd
Optional offset DWORD0
.
.
.
Optional offset DWORDn
Offset + Data DWORD0
.
.
.
.
.
Last Data & PAD
Optional Pad DWORD0
.
.
.
Optional Pad DWORDn
Last
Figure 3.14 TX Buffer Format
Figure 3.14, "TX Buffer Format", shows the TX Buffer as it is written into the LAN9221/LAN9221i. It
should be noted that not all of the data shown in this diagram is actually stored in the TX data FIFO.
This must be taken into account when calculating the actual TX data FIFO usage. Please refer to
Section 3.12.5, "Calculating Actual TX Data FIFO Usage," on page 56 for a detailed explanation on
calculating the actual TX data FIFO usage.
3.12.2
TX Command Format
The TX command instructs the TX FIFO controller on handling the subsequent buffer. The command
precedes the data to be transmitted. The TX command is divided into two, 32-bit words; TX command
‘A’ and TX command ‘B’.
There is a 16-bit packet tag in the TX command ‘B’ command word. Packet tags may, if host software
desires, be unique for each packet (i.e., an incrementing count). The value of the tag will be returned
in the RX status word for the associated packet. The Packet tag can be used by host software to
uniquely identify each status word as it is returned to the host.
Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX
command ‘B’ must be identical for every buffer in a given packet. If the TX command ‘B’ words do not
match, the Ethernet controller will assert the Transmitter Error (TXE) flag.
Revision 2.6 (12-04-08)
52
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
TX COMMAND ‘A’
Table 3.12 TX Command 'A' Format
BITS
DESCRIPTION
31
Interrupt on Completion. When set, the TXDONE flag will be asserted when the current buffer has
been fully loaded into the TX FIFO. This flag may be optionally mapped to a host interrupt.
30:26
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
25:24
Buffer End Alignment. This field specifies the alignment that must be maintained on the last data
transfer of a buffer. The host will add extra DWORDs of data up to the alignment specified in the
table below. The LAN9221/LAN9221i will remove the extra DWORDs. This mechanism can be used
to maintain cache line alignment on host processors.
[25]
[24]
End Alignment
0
0
4-byte alignment
0
1
16-byte alignment
1
0
32-byte alignment
1
1
Reserved
23:21
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility
20:16
Data Start Offset (bytes). This field specifies the offset of the first byte of TX data. The offset value
can be anywhere from 0 bytes to 31 a Byte offset.
15:14
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility
13
First Segment (FS). When set, this bit indicates that the associated buffer is the first segment of the
packet.
12
Last Segment. When set, this bit indicates that the associated buffer is the last segment of the
packet
11
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Buffer Size (bytes). This field indicates the number of bytes contained in the buffer following this
command. This value, along with the Buffer End Alignment field, is read and checked by the
LAN9221/LAN9221i and used to determine how many extra DWORD’s were added to the end of the
Buffer. A running count is also maintained in the LAN9221/LAN9221i of the cumulative buffer sizes
for a given packet. This cumulative value is compared against the Packet Length field in the TX
command ‘B’ word and if they do not correlate, the TXE flag is set.
Note:
SMSC LAN9221/LAN9221i
The buffer size specified does not include the buffer end alignment padding or data start
offset added to a buffer.
53
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
TX COMMAND ‘B’
Table 3.13 TX Command 'B' Format
BITS
DESCRIPTION
31:16
Packet Tag. The host should write a unique packet identifier to this field. This identifier is added to
the corresponding TX status word and can be used by the host to correlate TX status words with
their corresponding packets.
Note:
The use of packet tags is not required by the hardware. This field can be used by the LAN
software driver for any application. Packet Tags is one application example.
15
Reserved. This bit is reserved. Always write zeros to this bit to guarantee future compatibility.
14
TX Checksum Enable (CK). When this bit is set in conjunction with the first segment (FS) bit in TX
Command ‘A’ and the TX checksum offload engine enable bit (TXCOE_EN) in the
COE_CR—Checksum Offload Engine Control Register, the TX checksum offload engine (TXCOE)
will calculate a L3 checksum for the associated frame.
13
Add CRC Disable. When set, the automatic addition of the CRC is disabled.
12
Disable Ethernet Frame Padding. When set, this bit prevents the automatic addition of padding to
an Ethernet frame of less than 64 bytes. The CRC field is also added despite the state of the Add
CRC Disable field.
11
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Packet Length (bytes). This field indicates the total number of bytes in the current packet. This
length does not include the offset or padding. If the Packet Length field does not match the actual
number of bytes in the packet the Transmitter Error (TXE) flag will be set.
3.12.3
TX Data Format
The TX data section begins at the third DWORD in the TX buffer (after TX command ‘A’ and TX
command ‘B’). The location of the first byte of valid buffer data to be transmitted is specified in the
“Data Start Offset” field of the TX command ‘A’ word. Table 3.14, "TX DATA Start Offset", shows the
correlation between the setting of the LSB’s in the “Data Start Offset” field and the byte location of the
first valid data byte. Additionally, transmit buffer data can be offset by up to 7 additional DWORDS as
indicated by the upper three MSB’s (5:2) in the “Data Start Offset” field.
Table 3.14 TX DATA Start Offset
Data Start Offset [1:0]:
First TX Data Byte:
11
D[31:24]
10
D[23:16]
01
D[15:8]
00
D[7:0]
TX data is contiguous until the end of the buffer. The buffer may end on a byte boundary. Unused
bytes at the end of the packet will not be sent to the MIL for transmission.
The Buffer End Alignment field in TX command ‘A’ specifies the alignment that must be maintained for
the associated buffer. End alignment may be specified as 4-, 16-, or 32-byte. The host processor is
responsible for adding the additional data to the end of the buffer. The hardware will automatically
remove this extra data.
3.12.3.1
TX Buffer Fragmentation Rules
Transmit buffers must adhere to the following rules:
„
Each buffer can start and end on any arbitrary byte alignment
„
The first buffer of any transmit packet can be any length
Revision 2.6 (12-04-08)
54
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
„
Middle buffers (i.e., those with First Segment = Last Segment = 0) must be greater than, or equal
to 4 bytes in length
„
The final buffer of any transmit packet can be any length
The MIL operates in store-and-forward mode and has specific rules with respect to fragmented
packets. The total space consumed in the TX FIFO (MIL) must be limited to no more than 2KB - 3
DWORDs (2,036 bytes total). Any transmit packet that is so highly fragmented that it takes more space
than this must be un-fragmented (by copying to a driver-supplied buffer) before the transmit packet
can be sent to the LAN9221/LAN9221i.
One approach to determine whether a packet is too fragmented is to calculate the actual amount of
space that it will consume, and check it against 2,036 bytes. Another approach is to check the number
of buffers against a worst-case limit of 86 (see explanation below).
3.12.3.2
Calculating Worst-Case TX FIFO (MIL) Usage
The actual space consumed by a buffer in the MIL TX FIFO consists only of any partial DWORD offsets
in the first/last DWORD of the buffer, plus all of the whole DWORDs in between. Any whole DWORD
offsets and/or alignments are stripped off before the buffer is loaded into the TX Data FIFO, and TX
command words are stripped off before the buffer is written to the MIL TX FIFO, so none of those
DWORDs count as space consumed. The worst-case overhead for a TX buffer is 6 bytes, which
assumes that it started on the high byte of a DWORD and ended on the low byte of a DWORD. A TX
packet consisting of 86 such fragments would have an overhead of 516 bytes (6 * 86) which, when
added to a 1514-byte max-size transmit packet (1516 bytes, rounded up to the next whole DWORD),
would give a total space consumption of 2,032 bytes, leaving 4 bytes to spare; this is the basis for the
"86 fragment" rule mentioned above.
3.12.4
TX Status Format
TX status is passed to the host CPU through a separate FIFO mechanism. A status word is returned
for each packet transmitted. Data transmission is suspended if the TX status FIFO becomes full. Data
transmission will resume when the host reads the TX status and there is room in the FIFO for more
“TX Status” data.
The host can optionally choose to not read the TX status. The host can optionally ignore the TX status
by setting the “TX Status Discard Allow Overrun Enable” (TXSAO) bit in the TX Configuration Register
(TX_CFG). If this option is chosen TX status will not be written to the FIFO. Setting this bit high allows
the transmitter to continue operation with a full TX status FIFO. In this mode the status information is
still available in the TX status FIFO, and TX status interrupts still function. In the case of an overrun,
the TXSUSED counter will stay at zero and no further TX status will be written to the TX status FIFO
until the host frees space by reading TX status. If TXSAO is enabled, a TXE error will not be generated
if the TX status FIFO overruns. In this mode the host is responsible for re-synchronizing TX status in
the case of an overrun.
BITS
DESCRIPTION
31:16
Packet TAG. Unique identifier written by the host into the Packet Tag field of the TX command ‘B’
word. This field can be used by the host to correlate TX status words with the associated TX packets.
15
Error Status (ES). When set, this bit indicates that the Ethernet controller has reported an error. This
bit is the logical OR of bits 11, 10, 9, 8, 2, 1 in this status word.
14:12
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
11
Loss of Carrier. When set, this bit indicates the loss of carrier during transmission.
SMSC LAN9221/LAN9221i
55
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
10
DESCRIPTION
No Carrier. When set, this bit indicates that the carrier signal from the transceiver was not present
during transmission.
Note:
During 10/100 Mbps full-duplex transmission, the value of this bit is invalid and should be
ignored.
9
Late Collision. When set, indicates that the packet transmission was aborted after the collision
window of 64 bytes.
8
Excessive Collisions. When set, this bit indicates that the transmission was aborted after 16
collisions while attempting to transmit the current packet.
7
Reserved. This bit is reserved. Always write zeros to this field to guarantee future compatibility.
6:3
Collision Count. This counter indicates the number of collisions that occurred before the packet was
transmitted. It is not valid when excessive collisions (bit 8) is also set.
2
Excessive Deferral. If the deferred bit is set in the control register, the setting of the excessive
deferral bit indicates that the transmission has ended because of a deferral of over 24288 bit times
during transmission.
1
Reserved. This bit is reserved. Always write zero to this bit to guarantee future compatibility.
0
Deferred. When set, this bit indicates that the current packet transmission was deferred.
3.12.5
Calculating Actual TX Data FIFO Usage
The following rules are used to calculate the actual TX data FIFO space consumed by a TX Packet:
„
TX command 'A' is stored in the TX data FIFO for every TX buffer
„
TX command 'B' is written into the TX data FIFO when the First Segment (FS) bit is set in TX
command 'A'
„
When TX checksum is enabled, the 4-byte TX checksum preamble is written into TX Data FIFO.
„
Any DWORD-long data added as part of the “Data Start Offset” is removed from each buffer before
the data is written to the TX data FIFO. Any data that is less than 1 DWORD is passed to the TX
data FIFO.
„
Payload from each buffer within a Packet is written into the TX data FIFO.
„
Any DWORD-long data added as part of the End Padding is removed from each buffer before the
data is written to the TX data FIFO. Any end padding that is less than 1 DWORD is passed to the
TX data FIFO
Revision 2.6 (12-04-08)
56
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.12.6
Transmit Examples
3.12.6.1
TX Example 1
In this example a single, 111-Byte Ethernet packet will be transmitted. This packet is divided into three
buffers. The three buffers are as follows:
Buffer 0:
„
7-Byte “Data Start Offset”
„
79-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Buffer 1:
„
0-Byte “Data Start Offset”
„
15-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Buffer 2:
„
10-Byte “Data Start Offset”
„
17-Bytes of payload data
„
16-Byte “Buffer End Alignment”
SMSC LAN9221/LAN9221i
57
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Figure 3.15, "TX Example 1" illustrates the TX command structure for this example, and also shows
how data is passed to the TX data FIFO.
Data Written to the
Ethernet Controller
31
TX Com m and 'A'
Buffer End Alignment = 1
Data Start Offset = 7
First Segment = 1
Last Segment = 0
Buffer Size = 79
0
TX Command'A'
Data Passed to the
TX Data FIFO
TX Command'B'
7-Byte Data Start Offset
TX Command'A'
TX Com m and 'B'
Packet Length = 111
TX Command'B'
79-Byte Payload
79-Byte Payload
Pad DWORD 1
10-Byte
EndPadding
TX Command'A'
31
TX Com m and 'A'
Buffer End Alignment = 1
Data Start Offset = 0
First Segment = 0
Last Segment = 0
Buffer Size = 15
0
TX Command'A'
15-Byte Payload
TX Command'B'
TX Command'A'
15-Byte Payload
TX Com m and 'B'
Packet Length = 111
1B
17-Byte Payload
31
TX Com m and 'A'
Buffer End Alignment = 1
Data Start Offset = 10
First Segment = 0
Last Segment = 1
Buffer Size = 17
10-Byte
TXOffset
Command
'A'
End
Padding
TX Command'B'
0
10-Byte
Data Start Offset
NOTE: Extra bytes
betw een buffers are
not transmitted
TX Com m and 'B'
Packet Length = 111
17-Byte PayloadData
5-Byte EndPadding
Figure 3.15 TX Example 1
Revision 2.6 (12-04-08)
58
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.12.6.2
TX Example 2
In this example, a single 183-Byte Ethernet packet will be transmitted. This packet is in a single buffer
as follows:
„
2-Byte “Data Start Offset”
„
183-Bytes of payload data
„
4-Byte “Buffer End Alignment”
Figure 3.16, "TX Example 2" illustrates the TX command structure for this example, and also shows
how data is passed to the TX data FIFO. Note that the packet resides in a single TX Buffer, therefore
both the FS and LS bits are set in TX command ‘A’.
Data Passed to the
TX Data FIFO
Data Written to the
Ethernet Controller
TX Command 'A'
Buffer End Alignment = 0
Data Start Offset = 6
First Segment = 1
Last Segment = 1
Buffer Size =183
31
0
TX Command 'A'
TX Command 'A'
TX Command 'B'
TX Command 'B'
6-Byte Data Start Offset
TX Command 'B'
Packet Length = 183
183-Byte Payload Data
183-Byte Payload Data
3B End Padding
NOTE: Extra bytes between buffers
are not transmitted
Figure 3.16 TX Example 2
SMSC LAN9221/LAN9221i
59
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.12.6.3
TX Example 3
In this example a single, 111-Byte Ethernet packet will be transmitted with a TX checksum. This packet
is divided into four buffers. The four buffers are as follows:
Buffer 0:
„
4-Byte “Data Start Offset”
„
4-Byte Checksum Preamble
„
16-Byte “Buffer End Alignment”
Buffer 1:
„
7-Byte “Data Start Offset”
„
79-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Buffer 2:
„
0-Byte “Data Start Offset”
„
15-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Buffer 3:
„
10-Byte “Data Start Offset”
„
17-Bytes of payload data
„
16-Byte “Buffer End Alignment”
Figure 3.15, "TX Example 1" illustrates the TX command structure for this example, and also shows
how data is passed to the TX data FIFO.
Note: In order to perform a TX checksum calculation on the associated packet, bit 14 (CK) of the TX
Command ‘B’ must be set in conjunction with bit 13 (FS) of TX Command ‘A’ and bit 16
(TXCOE_EN) of the COE_CR register. For more information, refer to Section 3.6.2, "Transmit
Checksum Offload Engine (TXCOE)".
Revision 2.6 (12-04-08)
60
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Data Written to the
Ethernet Controller
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 4
First Segment = 1
Last Segment = 0
Buffer Size = 4
31
NOTE: When enabled, the TX Checksum
Preamble is pre-pended to data to be
transmitted. The FS bit in TX Command 'A', the
CK bit in TX Command 'B' and the TXCOE_EN
bit in the COE_CR register must all be set for
the TX checksum to be generated. FS must
not be set for subsequent fragments of the
same packet.
0
TX Command 'A'
TX Command 'B'
4-Byte Data Start Offset
TX Checksum Preamble
TX Command 'B'
Packet Length = 115
TX Checksum Enable = 1
Data Passed to the
TX Data FIFO
8-Byte End Padding
Checksum Preamble
TX Checksum Location = 50
TX Checksum Start Pointer = 14
TX Command 'A'
31
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 7
First Segment = 0
Last Segment = 0
Buffer Size = 79
TX Command 'B'
0
TX Command 'A'
TX Checksum Preamble
TX Command 'B'
TX Command 'A'
7-Byte Data Start Offset
TX Command 'B'
Packet Length = 115
TX Checksum Enable = 1
79-Byte Payload
79-Byte Payload
Pad DWORD 1
TX Command 'A'
10-Byte
End Padding
15-Byte Payload
31
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 0
First Segment = 0
Last Segment = 0
Buffer Size = 15
0
TX Command 'B'
17-Byte Payload
15-Byte Payload
TX Command 'B'
Packet Length = 115
TX Checksum Enable = 1
1B
31
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 10
First Segment = 0
Last Segment = 1
Buffer Size = 17
TX Command 'A'
TX Command 'A'
10-Byte
TX Offset
Command
'A'
End
Padding
0
TX Command 'B'
NOTE: Extra bytes
between buffers are
not transmitted
10-Byte
Data Start Offset
TX Command 'B'
Packet Length = 115
TX Checksum Enable = 1
17-Byte Payload Data
5-Byte End Padding
Figure 3.17 TX Example 3
SMSC LAN9221/LAN9221i
61
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.12.7
Transmitter Errors
If the Transmitter Error (TXE) flag is asserted for any reason, the transmitter will continue operation.
TX Error (TXE) will be asserted under the following conditions:
3.12.8
„
If the actual packet length count does not match the Packet Length field as defined in the TX
command.
„
Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX
command ‘B’ must be identical for every buffer in a given packet. If the TX command ‘B’ words do
not match, the Ethernet controller will assert the Transmitter Error (TXE) flag.
„
Host overrun of the TX data FIFO.
„
Overrun of the TX status FIFO (unless TXSAO is enabled)
Stopping and Starting the Transmitter
To halt the transmitter, the host must set the TX_STOP bit in the TX_CFG register. The transmitter will
finish sending the current frame (if there is a frame transmission in progress). When the transmitter
has received the TX status for this frame, it will clear the TX_STOP and TX_ON bits, and will pulse
the TXSTOP_INT.
Once stopped, the host can optionally clear the TX status and TX data FIFOs. The host must re-enable
the transmitter by setting the TX_ON bit. If the there are frames pending in the TX data FIFO (i.e., TX
data FIFO was not purged), the transmission will resume with this data.
3.13
RX Data Path Operation
When an Ethernet Packet is received, the MIL first begins to transfer the RX data. This data is loaded
into the RX data FIFO. The RX data FIFO pointers are updated as data is written into the FIFO.
The last transfer from the MIL is the RX status word. The LAN9221/LAN9221i implements a separate
FIFO for the RX status words. The total available RX data and status queued in the RX FIFO can be
read from the RX_FIFO_INF register. The host may read any number of available RX status words
before reading the RX data FIFO.
The host must use caution when reading the RX data and status. The host must never read more data
than what is available in the FIFOs. If this is attempted an underrun condition will occur. If this error
occurs, the Ethernet controller will assert the Receiver Error (RXE) interrupt. If an underrun condition
occurs, a soft reset is required to regain host synchronization.
A configurable beginning offset is supported in the LAN9221/LAN9221i. The RX data Offset field in the
RX_CFG register controls the number of bytes that the beginning of the RX data buffer is shifted. The
host can set an offset from 0-31 bytes. The offset may be changed in between RX packets, but it must
not be changed during an RX packet read.
The LAN9221/LAN9221i can be programmed to add padding at the end of a receive packet in the
event that the end of the packet does not align with the host burst boundary. This feature is necessary
when the LAN9221/LAN9221i is operating in a system that always performs multi-DWORD bursts. In
such cases the LAN9221/LAN9221i must guarantee that it can transfer data in multiples of the Burst
length regardless of the actual packet length. When configured to do so, the LAN9221/LAN9221i will
add extra data at the end of the packet to allow the host to perform the necessary number of reads
so that the Burst length is not cut short. Once a packet has been padded by the H/W, it is the
responsibility of the host to interrogate the Packet length field in the RX status and determine how
much padding to discard at the end of the Packet.
It is possible to read multiple packets out of the RX data FIFO in one continuous stream. It should be
noted that the programmed Offset and Padding will be added to each individual packet in the stream,
since packet boundaries are maintained.
Revision 2.6 (12-04-08)
62
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.13.1
RX Slave PIO Operation
Using PIO mode, the host can either implement a polling or interrupt scheme to empty the received
packet out of the RX data FIFO. The host will remain in the idle state until it receives an indication
(interrupt or polling) that data is available in the RX data FIFO. The host will then read the RX status
FIFO to get the packet status, which will contain the packet length and any other status information.
The host should perform the proper number of reads, as indicated by the packet length plus the start
offset and the amount of optional padding added to the end of the frame, from the RX data FIFO.
init
Idle
RX Interrupt
Read RX
Status
DWORD
Not Last Packet
Last Packet
Read RX
Packet
Figure 3.18 Host Receive Routine Using Interrupts
init
Read
RX_FIFO_
INf
Valid Status DWORD
Read RX
Status
DWORD
Not Last Packet
Last Packet
Read RX
Packet
Figure 3.19 Host Receive Routine with Polling
SMSC LAN9221/LAN9221i
63
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.13.1.1
Receive Data FIFO Fast Forward
The RX data path implements an automatic data discard function. Using the RX data FIFO Fast
Forward bit (RX_FFWD) in the RX_DP_CTRL register, the host can instruct the LAN9221/LAN9221i
to skip the packet at the head of the RX data FIFO. The RX data FIFO pointers are automatically
incremented to the beginning of the next RX packet.
When performing a fast-forward, there must be at least 4 DWORDs of data in the RX data FIFO for
the packet being discarded. For less than 4 DWORDs do not use RX_FFWD. In this case data must
be read from the RX data FIFO and discarded using standard PIO read operations.
After initiating a fast-forward operation, do not perform any reads of the RX data FIFO until the
RX_FFWD bit is cleared. Other resources can be accessed during this time (i.e., any registers and/or
the other three FIFOs). Also note that the RX_FFWD will only fast-forward the RX data FIFO, not the
RX status FIFO.
The receiver does not have to be stopped to perform a fast-forward operation.
3.13.1.2
Force Receiver Discard (Receiver Dump)
In addition to the Receive data Fast Forward feature, LAN9221/LAN9221i also implements a receiver
"dump" feature. This feature allows the host processor to flush the entire contents of the RX data and
RX status FIFOs. When activated, the read and write pointers for the RX data and status FIFOs will
be returned to their reset state. To perform a receiver dump, the LAN9221/LAN9221i receiver must be
halted. Once the receiver stop completion is confirmed, the RX_DUMP bit can be set in the RX_CFG
register. The RX_DUMP bit is cleared when the dump is complete. For more information on stopping
the receiver, please refer to Section 3.13.4, "Stopping and Starting the Receiver," on page 67. For more
information on the RX_DUMP bit, please refer to Section 5.3.7, "RX_CFG—Receive Configuration
Register," on page 87.
Revision 2.6 (12-04-08)
64
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
3.13.2
RX Packet Format
The RX status words can be read from the RX status FIFO port, while the RX data packets can be
read from the RX data FIFO. RX data packets are formatted in a specific manner before the host can
read them as shown in Figure 3.20. It is assumed that the host has previously read the associated
status word from the RX status FIFO, to ascertain the data size and any error conditions.
Host Read
Order
31
0
1st
Optional offset DWORD0
2nd
.
.
Optional offset DWORDn
ofs + First Data DWORD
.
.
.
.
Last Data DWORD
Optional Pad DWORD0
.
.
Last
Optional Pad DWORDn
Figure 3.20 RX Packet Format
Figure 3.21 shows the RX packet format when the RX checksum is enabled. The RX checksum data
appended to the data payload is treated just as an additional 4-bytes within the RX Data FIFO. The
RX checksum is enabled by setting the RXCOE_EN bit in the COE_CR—Checksum Offload Engine
Control Register. For more information on the RX checksum, refer to Section 3.6.1, "Receive
Checksum Offload Engine (RXCOE)".
SMSC LAN9221/LAN9221i
65
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Host Read
Order
31
0
1st
Optional offset DWORD0
2nd
.
.
Optional offset DWORDn
ofs + First Data DWORD
.
.
.
.
Last Data DWORD
RX
Checksum
Optional Pad DWORD0
.
.
Last
Optional Pad DWORDn
Figure 3.21 RX Packet Format with RX Checksum
3.13.3
RX Status Format
BITS
DESCRIPTION
31
Reserved. This bit is reserved. Reads 0.
30
Filtering Fail. When set, this bit indicates that the associated frame failed the address recognizing
filtering.
29:16
Packet Length. The size, in bytes, of the corresponding received frame.
15
Error Status (ES). When set this bit indicates that the MIL has reported an error. This bit is the
Internal logical “or” of bits 11,7,6 and 1.
14
Reserved. These bits are reserved. Reads 0.
13
Broadcast Frame. When set, this bit indicates that the received frame has a Broadcast address.
12
Length Error (LE). When set, this bit indicates that the actual length does not match with the
length/type field of the received frame.
11
Runt Frame. When set, this bit indicates that frame was prematurely terminated before the collision
window (64 bytes). Runt frames are passed on to the host only if the Pass Bad Frames bit MAC_CR
Bit [16] is set.
10
Multicast Frame. When set, this bit indicates that the received frame has a Multicast address.
9:8
Reserved. These bits are reserved. Reads 0.
Revision 2.6 (12-04-08)
66
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
7
Frame Too Long. When set, this bit indicates that the frame length exceeds the maximum Ethernet
specification of 1518 bytes. This is only a frame too long indication and will not cause the frame
reception to be truncated.
6
Collision Seen. When set, this bit indicates that the frame has seen a collision after the collision
window. This indicates that a late collision has occurred.
5
Frame Type. When set, this bit indicates that the frame is an Ethernet-type frame (Length/Type field
in the frame is greater than 1500). When reset, it indicates the incoming frame was an 802.3 type
frame. This bit is not set for Runt frames less than 14 bytes.
4
Receive Watchdog time-out. When set, this bit indicates that the incoming frame is greater than
2048 bytes through 2560 bytes, therefore expiring the Receive Watchdog Timer.
3
MII Error. When set, this bit indicates that a receive error (RX_ER asserted) was detected during
frame reception.
2
Dribbling Bit. When set, this bit indicates that the frame contained a non-integer multiple of 8 bits.
This error is reported only if the number of dribbling bits in the last byte is 4 in the MII operating mode,
or at least 3 in the 10 Mbps operating mode. This bit will not be set when the collision seen bit[6] is
set. If set and the CRC error bit[1] is cleared, then the packet is considered to be valid.
1
CRC Error. When set, this bit indicates that a CRC error was detected. This bit is also set when the
RX_ER pin is asserted during the reception of a frame even though the CRC may be correct. This bit
is not valid if the received frame is a Runt frame, or a late collision was detected or when the
Watchdog Time-out occurs.
0
Reserved. These bits are reserved. Reads 0
3.13.4
Stopping and Starting the Receiver
To stop the receiver, the host must clear the RXEN bit in the MAC Control Register. When the receiver
is halted, the RXSTOP_INT will be pulsed. Once stopped, the host can optionally clear the RX status
and RX data FIFOs. The host must re-enable the receiver by setting the RXEN bit.
3.13.5
Receiver Errors
If the Receiver Error (RXE) flag is asserted for any reason, the receiver will continue operation. RX
Error (RXE) will be asserted under the following conditions:
„
A host underrun of RX data FIFO
„
A host underrun of the RX status FIFO
„
An overrun of the RX status FIFO
It is the duty of the host to identify and resolve any error conditions.
SMSC LAN9221/LAN9221i
67
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 4 Internal Ethernet PHY
4.1
Top Level Functional Description
Functionally, the internal PHY can be divided into the following sections:
„
100Base-TX transmit and receive
„
10Base-T transmit and receive
„
Internal MII interface to the Ethernet Media Access Controller
„
Auto-negotiation to automatically determine the best speed and duplex possible
„
Management Control to read status registers and write control registers
100M
PLL
TX_CLK
MAC
Internal
MII 25 MHz by 4 bits
25MHz
by 4 bits
MII
4B/5B
Encoder
25MHz by
5 bits
MLT-3
Magnetics
Scrambler
and PISO
125 Mbps Serial
NRZI
Converter
NRZI
MLT-3
Converter
MLT-3
Tx
Driver
MLT-3
RJ45
MLT-3
CAT-5
Figure 4.1 100Base-TX Data Path
4.2
100Base-TX Transmit
The data path of the 100Base-TX is shown in Figure 4.1. Each major block is explained below.
4.2.1
4B/5B Encoding
The transmit data passes from the MII block to the 4B/5B encoder. This block encodes the data from
4-bit nibbles to 5-bit symbols (known as “code-groups”) according to Table 4.1. Each 4-bit data-nibble
is mapped to 16 of the 32 possible code-groups. The remaining 16 code-groups are either used for
control information or are not valid.
The first 16 code-groups are referred to by the hexadecimal values of their corresponding data nibbles,
0 through F. The remaining code-groups are given letter designations with slashes on either side. For
example, an IDLE code-group is /I/, a transmit error code-group is /H/, etc.
The encoding process may be bypassed by clearing bit 6 of register 31. When the encoding is
bypassed the 5th transmit data bit is equivalent to TX_ER.
Revision 2.6 (12-04-08)
68
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 4.1 4B/5B Code Table
CODE
GROUP
SYM
RECEIVER
INTERPRETATION
11110
0
0
0000
01001
1
1
10100
2
10101
TRANSMITTER
INTERPRETATION
0
0000
0001
1
0001
2
0010
2
0010
3
3
0011
3
0011
01010
4
4
0100
4
0100
01011
5
5
0101
5
0101
01110
6
6
0110
6
0110
01111
7
7
0111
7
0111
10010
8
8
1000
8
1000
10011
9
9
1001
9
1001
10110
A
A
1010
A
1010
10111
B
B
1011
B
1011
11010
C
C
1100
C
1100
11011
D
D
1101
D
1101
11100
E
E
1110
E
1110
11101
F
F
1111
F
1111
11111
I
IDLE
Sent after /T/R until TX_EN
11000
J
First nibble of SSD, translated to “0101”
following IDLE, else RX_ER
Sent for rising TX_EN
10001
K
Second nibble of SSD, translated to
“0101” following J, else RX_ER
Sent for rising TX_EN
01101
T
First nibble of ESD, causes de-assertion
of CRS if followed by /R/, else assertion
of RX_ER
Sent for falling TX_EN
00111
R
Second nibble of ESD, causes
deassertion of CRS if following /T/, else
assertion of RX_ER
Sent for falling TX_EN
00100
H
Transmit Error Symbol
Sent for rising TX_ER
00110
V
INVALID, RX_ER if during RX_DV
INVALID
11001
V
INVALID, RX_ER if during RX_DV
INVALID
00000
V
INVALID, RX_ER if during RX_DV
INVALID
00001
V
INVALID, RX_ER if during RX_DV
INVALID
00010
V
INVALID, RX_ER if during RX_DV
INVALID
00011
V
INVALID, RX_ER if during RX_DV
INVALID
00101
V
INVALID, RX_ER if during RX_DV
INVALID
SMSC LAN9221/LAN9221i
DATA
69
DATASHEET
DATA
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 4.1 4B/5B Code Table (continued)
CODE
GROUP
SYM
01000
V
INVALID, RX_ER if during RX_DV
INVALID
01100
V
INVALID, RX_ER if during RX_DV
INVALID
10000
V
INVALID, RX_ER if during RX_DV
INVALID
4.2.2
RECEIVER
INTERPRETATION
TRANSMITTER
INTERPRETATION
Scrambling
Repeated data patterns (especially the IDLE code-group) can have power spectral densities with large
narrow-band peaks. Scrambling the data helps eliminate these peaks and spread the signal power
more uniformly over the entire channel bandwidth. This uniform spectral density is required by FCC
regulations to prevent excessive EMI from being radiated by the physical wiring.
The scrambler also performs the Parallel In Serial Out conversion (PISO) of the data.
4.2.3
NRZI and MLT3 Encoding
The scrambler block passes the 5-bit wide parallel data to the NRZI converter where it becomes a
serial 125MHz NRZI data stream. The NRZI is encoded to MLT-3. MLT3 is a tri-level code where a
change in the logic level represents a code bit “1” and the logic output remaining at the same level
represents a code bit “0”.
4.2.4
100M Transmit Driver
The MLT3 data is then passed to the analog transmitter, which launches the differential MLT-3 signal,
on outputs TXP and TXN, to the twisted pair media via a 1:1 ratio isolation transformer. The 10BaseT and 100Base-TX signals pass through the same transformer so that common “magnetics” can be
used for both. The transmitter drives into the 100Ω impedance of the CAT-5 cable. Cable termination
and impedance matching require external components.
4.2.5
100M Phase Lock Loop (PLL)
The 100M PLL locks onto reference clock and generates the 125MHz clock used to drive the 125 MHz
logic and the 100Base-Tx Transmitter.
Revision 2.6 (12-04-08)
70
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
100M
PLL
RX_CLK
MAC
Internal
MII 25MHz by 4 bits
25MHz
by 4 bits
MII
4B/5B
Decoder
25MHz by
5 bits
Descrambler
and SIPO
125 Mbps Serial
NRZI
Converter
A/D
Converter
NRZI
MLT-3
MLT-3
Converter
Magnetics
DSP: Timing
recovery, Equalizer
and BLW Correction
MLT-3
RJ45
MLT-3
MLT-3
CAT-5
6 bit Data
Figure 4.2 Receive Data Path
4.3
100Base-TX Receive
The receive data path is shown in Figure 4.2. Detailed descriptions are given below.
4.3.1
100M Receive Input
The MLT-3 from the cable is fed into the PHY (on inputs RXP and RXN) via a 1:1 ratio transformer.
The ADC samples the incoming differential signal at a rate of 125M samples per second. Using a 64level quanitizer it generates 6 digital bits to represent each sample. The DSP adjusts the gain of the
ADC according to the observed signal levels such that the full dynamic range of the ADC can be used.
4.3.2
Equalizer, Baseline Wander Correction and Clock and Data Recovery
The 6 bits from the ADC are fed into the DSP block. The equalizer in the DSP section compensates
for phase and amplitude distortion caused by the physical channel consisting of magnetics, connectors,
and CAT- 5 cable. The equalizer can restore the signal for any good-quality CAT-5 cable between 1m
and 150m.
If the DC content of the signal is such that the low-frequency components fall below the low frequency
pole of the isolation transformer, then the droop characteristics of the transformer will become
significant and Baseline Wander (BLW) on the received signal will result. To prevent corruption of the
received data, the PHY corrects for BLW and can receive the ANSI X3.263-1995 FDDI TP-PMD
defined “killer packet” with no bit errors.
The 100M PLL generates multiple phases of the 125MHz clock. A multiplexer, controlled by the timing
unit of the DSP, selects the optimum phase for sampling the data. This is used as the received
recovered clock. This clock is used to extract the serial data from the received signal.
4.3.3
NRZI and MLT-3 Decoding
The DSP generates the MLT-3 recovered levels that are fed to the MLT-3 converter. The MLT-3 is then
converted to an NRZI data stream.
SMSC LAN9221/LAN9221i
71
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
4.3.4
Descrambling
The descrambler performs an inverse function to the scrambler in the transmitter and also performs
the Serial In Parallel Out (SIPO) conversion of the data.
During reception of IDLE (/I/) symbols. the descrambler synchronizes its descrambler key to the
incoming stream. Once synchronization is achieved, the descrambler locks on this key and is able to
descramble incoming data.
Special logic in the descrambler ensures synchronization with the remote PHY by searching for IDLE
symbols within a window of 4000 bytes (40us). This window ensures that a maximum packet size of
1514 bytes, allowed by the IEEE 802.3 standard, can be received with no interference. If no IDLEsymbols are detected within this time-period, receive operation is aborted and the descrambler re-starts
the synchronization process.
The descrambler can be bypassed by setting bit 0 of register 31.
4.3.5
Alignment
The de-scrambled signal is then aligned into 5-bit code-groups by recognizing the /J/K/ Start-of-Stream
Delimiter (SSD) pair at the start of a packet. Once the code-word alignment is determined, it is stored
and utilized until the next start of frame.
4.3.6
5B/4B Decoding
The 5-bit code-groups are translated into 4-bit data nibbles according to the 4B/5B table. The SSD,
/J/K/, is translated to “0101 0101” as the first 2 nibbles of the MAC preamble. Reception of the SSD
causes the PHY to assert the internal RX_DV signal, indicating that valid data is available on the
Internal RXD bus. Successive valid code-groups are translated to data nibbles. Reception of either the
End of Stream Delimiter (ESD) consisting of the /T/R/ symbols, or at least two /I/ symbols causes the
PHY to de-assert the internal carrier sense and RX_DV.
These symbols are not translated into data.
4.4
10Base-T Transmit
Data to be transmitted comes from the MAC layer controller. The 10Base-T transmitter receives 4-bit
nibbles from the MII at a rate of 2.5MHz and converts them to a 10Mbps serial data stream. The data
stream is then Manchester-encoded and sent to the analog transmitter, which drives a signal onto the
twisted pair via the external magnetics.
The 10M transmitter uses the following blocks:
4.4.1
„
MII (digital)
„
TX 10M (digital)
„
10M Transmitter (analog)
„
10M PLL (analog)
10M Transmit Data across the internal MII bus
The MAC controller drives the transmit data onto the internal TXD BUS. When the controller has driven
TX_EN high to indicate valid data, the data is latched by the MII block on the rising edge of TX_CLK.
The data is in the form of 4-bit wide 2.5MHz data.
4.4.2
Manchester Encoding
The 4-bit wide data is sent to the TX10M block. The nibbles are converted to a 10Mbps serial NRZI
data stream. The 10M PLL locks onto the external clock or internal oscillator and produces a 20MHz
Revision 2.6 (12-04-08)
72
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
clock. This is used to Manchester encode the NRZ data stream. When no data is being transmitted
(TX_EN is low), the TX10M block outputs Normal Link Pulses (NLPs) to maintain communications with
the remote link partner.
4.4.3
10M Transmit Drivers
The Manchester encoded data is sent to the analog transmitter where it is shaped and filtered before
being driven out as a differential signal across the TXP and TXN outputs.
4.5
10Base-T Receive
The 10Base-T receiver gets the Manchester- encoded analog signal from the cable via the magnetics.
It recovers the receive clock from the signal and uses this clock to recover the NRZI data stream. This
10M serial data is converted to 4-bit data nibbles which are passed to the controller across the MII at
a rate of 2.5MHz.
This 10M receiver uses the following blocks:
4.5.1
„
Filter and SQUELCH (analog)
„
10M PLL (analog)
„
RX 10M (digital)
„
MII (digital)
10M Receive Input and Squelch
The Manchester signal from the cable is fed into the PHY (on inputs RXP and RXN) via 1:1 ratio
magnetics. It is first filtered to reduce any out-of-band noise. It then passes through a SQUELCH
circuit. The SQUELCH is a set of amplitude and timing comparators that normally reject differential
voltage levels below 300mV and detect and recognize differential voltages above 585mV.
4.5.2
Manchester Decoding
The output of the SQUELCH goes to the RX10M block where it is validated as Manchester encoded
data. The polarity of the signal is also checked. If the polarity is reversed (local RXP is connected to
RXN of the remote partner and vice versa), then this is identified and corrected. The reversed condition
is indicated by the flag “XPOL“, bit 4 in register 27. The 10M PLL is locked onto the received
Manchester signal and from this, generates the received 20MHz clock. Using this clock, the
Manchester encoded data is extracted and converted to a 10MHz NRZI data stream. It is then
converted from serial to 4-bit wide parallel data.
The RX10M block also detects valid 10Base-T IDLE signals - Normal Link Pulses (NLPs) - to maintain
the link.
4.5.3
Jabber Detection
Jabber is a condition in which a station transmits for a period of time longer than the maximum
permissible packet length, usually due to a fault condition, that results in holding the TX_EN input for
a long period. Special logic is used to detect the jabber state and abort the transmission to the line,
within 45ms. Once TX_EN is deasserted, the logic resets the jabber condition.
4.6
Auto-negotiation
The purpose of the Auto-negotiation function is to automatically configure the PHY to the optimum link
parameters based on the capabilities of its link partner. Auto-negotiation is a mechanism for
exchanging configuration information between two link-partners and automatically selecting the highest
performance mode of operation supported by both sides. Auto-negotiation is fully defined in clause 28
of the IEEE 802.3 specification.
SMSC LAN9221/LAN9221i
73
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Once auto-negotiation has completed, information about the resolved link can be passed back to the
controller via the internal Serial Management Interface (SMI). The results of the negotiation process
are reflected in the Speed Indication bits in register 31, as well as the Link Partner Ability Register
(Register 5).
The auto-negotiation protocol is a purely physical layer activity and proceeds independently of the MAC
controller.
The advertised capabilities of the PHY are stored in register 4 of the SMI registers. The default
advertised by the PHY is determined by user-defined on-chip signal options.
The following blocks are activated during an Auto-negotiation session:
„
Auto-negotiation (digital)
„
100M ADC (analog)
„
100M PLL (analog)
„
100M equalizer/BLW/clock recovery (DSP)
„
10M SQUELCH (analog)
„
10M PLL (analog)
„
10M Transmitter (analog)
When enabled, auto-negotiation is started by the occurrence of one of the following events:
„
Hardware reset
„
Software reset
„
Power-down reset
„
Link status down
„
Setting register 0, bit 9 high (auto-negotiation restart)
On detection of one of these events, the PHY begins auto-negotiation by transmitting bursts of Fast
Link Pulses (FLP). These are bursts of link pulses from the 10M transmitter. They are shaped as
Normal Link Pulses and can pass uncorrupted down CAT-3 or CAT-5 cable. A Fast Link Pulse Burst
consists of up to 33 pulses. The 17 odd-numbered pulses, which are always present, frame the FLP
burst. The 16 even-numbered pulses, which may be present or absent, contain the data word being
transmitted. Presence of a data pulse represents a “1”, while absence represents a “0”.
The data transmitted by an FLP burst is known as a “Link Code Word.” These are defined fully in IEEE
802.3 clause 28. In summary, the PHY advertises 802.3 compliance in its selector field (the first 5 bits
of the Link Code Word). It advertises its technology ability according to the bits set in register 4 of the
SMI registers.
There are 4 possible matches of the technology abilities. In the order of priority these are:
„
100M full-duplex (Highest priority)
„
100M half-duplex
„
10M full-duplex
„
10M half-duplex
If the full capabilities of the PHY are advertised (100M, full-duplex), and if the link partner is capable
of 10M and 100M, then auto-negotiation selects 100M as the highest performance mode. If the link
partner is capable of half and full-duplex modes, then auto-negotiation selects full-duplex as the highest
performance operation.
Once a capability match has been determined, the link code words are repeated with the acknowledge
bit set. Any difference in the main content of the link code words at this time will cause auto-negotiation
to re-start. Auto-negotiation will also re-start if not all of the required FLP bursts are received.
Revision 2.6 (12-04-08)
74
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Writing register 4 bits [8:5] allows software control of the capabilities advertised by the PHY. Writing
register 4 does not automatically re-start auto-negotiation. Register 0, bit 9 must be set before the new
abilities will be advertised. Auto-negotiation can also be disabled via software by clearing register 0,
bit 12.
The LAN9221/LAN9221i does not support “Next Page" capability.
4.7
Parallel Detection
If the LAN9221/LAN9221i is connected to a device lacking the ability to auto-negotiate (i.e. no FLPs
are detected), it is able to determine the speed of the link based on either 100M MLT-3 symbols or
10M Normal Link Pulses. In this case the link is presumed to be half-duplex per the IEEE standard.
This ability is known as “Parallel Detection. This feature ensures inter operability with legacy link
partners. If a link is formed via parallel detection, then bit 0 in register 6 is cleared to indicate that the
Link Partner is not capable of auto-negotiation. The Ethernet MAC has access to this information via
the management interface. If a fault occurs during parallel detection, bit 4 of register 6 is set.
Register 5 is used to store the Link Partner Ability information, which is coded in the received FLPs.
If the Link Partner is not auto-negotiation capable, then register 5 is updated after completion of parallel
detection to reflect the speed capability of the Link Partner.
4.7.1
Re-starting Auto-negotiation
Auto-negotiation can be re-started at any time by setting register 0, bit 9. Auto-negotiation will also restart if the link is broken at any time. A broken link is caused by signal loss. This may occur because
of a cable break, or because of an interruption in the signal transmitted by the Link Partner. Autonegotiation resumes in an attempt to determine the new link configuration.
If the management entity re-starts Auto-negotiation by writing to bit 9 of the control register, the
LAN9221/LAN9221i will respond by stopping all transmission/receiving operations. Once the
break_link_timer is done, in the Auto-negotiation state-machine (approximately 1200ms) the autonegotiation will re-start. The Link Partner will have also dropped the link due to lack of a received
signal, so it too will resume auto-negotiation.
4.7.2
Disabling Auto-negotiation
Auto-negotiation can be disabled by setting register 0, bit 12 to zero. The device will then force its
speed of operation to reflect the information in register 0, bit 13 (speed) and register 0, bit 8 (duplex).
The speed and duplex bits in register 0 should be ignored when auto-negotiation is enabled.
4.7.3
Half vs. Full-Duplex
Half-duplex operation relies on the CSMA/CD (Carrier Sense Multiple Access / Collision Detect)
protocol to handle network traffic and collisions. In this mode, the internal carrier sense signal, CRS,
responds to both transmit and receive activity. In this mode, If data is received while the PHY is
transmitting, a collision results.
In full-duplex mode, the PHY is able to transmit and receive data simultaneously. In this mode, the
internal CRS responds only to receive activity. The CSMA/CD protocol does not apply and collision
detection is disabled.
Table 4.2 describes the behavior of the internal CRS bit under all receive/transmit conditions. The
internal CRS signal is used to trigger bit 10 (No Carrier) of the TX Status word (See Section 3.12.4,
"TX Status Format"). The CRS value, and subsequently the No Carrier value, are invalid during any
full-duplex transmission. Therefore, these signals cannot be used as a verification method of
transmitted packets when transmitting in 10/100 Mbps full-duplex modes.
SMSC LAN9221/LAN9221i
75
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 4.2 CRS Behavior
MODE
SPEED
DUPLEX
ACTIVITY
CRS BEHAVIOR
(Note 4.1)
Manual
10 Mbps
Half-Duplex
Transmitting
Active
Manual
10 Mbps
Half-Duplex
Receiving
Active
Manual
10 Mbps
Full-Duplex
Transmitting
Low
Manual
10 Mbps
Full-Duplex
Receiving
Active
Manual
100 Mbps
Half-Duplex
Transmitting
Active
Manual
100 Mbps
Half-Duplex
Receiving
Active
Manual
100 Mbps
Full-Duplex
Transmitting
Low
Manual
100 Mbps
Full-Duplex
Receiving
Active
Auto-Negotiation
10 Mbps
Half-Duplex
Transmitting
Active
Auto-Negotiation
10 Mbps
Half-Duplex
Receiving
Active
Auto-Negotiation
10 Mbps
Full-Duplex
Transmitting
Low
Auto-Negotiation
10 Mbps
Full-Duplex
Receiving
Active
Auto-Negotiation
100 Mbps
Half-Duplex
Transmitting
Active
Auto-Negotiation
100 Mbps
Half-Duplex
Receiving
Active
Auto-Negotiation
100 Mbps
Full-Duplex
Transmitting
Low
Auto-Negotiation
100 Mbps
Full-Duplex
Receiving
Active
Note 4.1
4.8
The LAN9221/LAN9221i 10/100 PHY internal CRS signal operates in two modes: Active
and Low. When in Active mode, the internal CRS will transition high and low upon line
activity, where a high value indicates a carrier has been detected. In Low mode, the
internal CRS stays low and does not indicate carrier detection. The internal CRS signal
and No Carrier (bit 10 of the TX Status word) cannot be used as a verification method of
transmitted packets when transmitting in 10/100 Mbps full-duplex mode.
HP Auto-MDIX
HP Auto-MDIX facilitates the use of CAT-3 (10 Base-T) or CAT-5 (100 Base-T) media UTP interconnect
cable without consideration of interface wiring scheme. If a user plugs in either a direct connect LAN
cable, or a cross-over patch cable, as shown in Figure 4.3, the SMSC LAN9221/LAN9221i Auto-MDIX
PHY is capable of configuring the TPO and TPI twisted pair pins for correct transceiver operation.
The internal logic of the device detects the TX and RX pins of the connecting device. Since the RX
and TX line pairs are interchangeable, special PCB design considerations are needed to accommodate
the symmetrical magnetics and termination of an Auto-MDIX design.
The Auto-MDIX function can be disabled through an internal register 27.15, or the external control pins
AMDIX_EN. When disabled the TX and RX pins can be configured with the Channel Select
(CH_SELECT) pin as desired.
Revision 2.6 (12-04-08)
76
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
The figure below shows the signal names at the RJ-45 connector, The mapping of these signals to the pins on
the LAN9221/LAN9221i is as follows:
TXP = TPO+
TXN = TPORXP = TPI+
RXN = TPI-
Figure 4.3 Direct cable connection vs. Cross-over cable connection.
SMSC LAN9221/LAN9221i
77
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 5 Register Description
The following section describes all LAN9221/LAN9221i registers and data ports.
FCh
RESERVED
B4h
B0h
ACh
A8h
A4h
A0h
50h
4Ch
48h
44h
40h
3Ch
EEPROM Port
MAC CSRPort
TX Status
TX Status
RX Status
RX Status
FIFO PEEK
FIFO Port
FIFO PEEK
FIFO Port
TX Data FIFO Alias Ports
24h
20h
1Ch
TX Data FIFO Port
RX Data FIFO Alias Ports
04h
Base + 00h
RX Data FIFO Port
Figure 5.1 Memory Map
Revision 2.6 (12-04-08)
78
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.1
Register Nomenclature and Access Attributes
SYMBOL
DESCRIPTION
RO
Read Only: If a register is read only, writes to this register have no effect.
WO
Write Only: If a register is write only, reads always return 0.
R/W
Read/Write: A register with this attribute can be read and written
R/WC
Read/Write Clear: A register bit with this attribute can be read and written. However, a write of a 1
clears (sets to 0) the corresponding bit and a write of a 0 has no effect.
RC
Read to Clear: A register bit with this attribute is cleared when read.
LL
Latch Low: Clear on read of register
LH
Latch High: Clear on read of register
SC
Self-Clearing
NASR
Not Affected by Software Reset
Reserved
Bits
Certain bits within registers are listed as “Reserved”. Unless stated otherwise, these bits must be
written with zeros for future compatibility. The values of these bits are not guaranteed when read.
Reserved
Registers
Certain configuration registers within the LAN9221/LAN9221i are listed as “Reserved”. These
registers are not guaranteed to return any particular value when read. These registers must not be
written to or modified by system failure; doing so could result in failure of the device and system.
Default
States
At Reset - System reset or Software Reset - internal registers are set to their default states.
The default states provide a minimum level of functionality needed to successfully bring up a system,
but do not necessarily provide desired or optimal configuration of the device. It is the responsibility
of the system initialization software to properly determine the operating parameters and optional
system features that are applicable, and to program the LAN9221/LAN9221i registers accordingly.
5.2
RX and TX FIFO Ports
The LAN9221/LAN9221i contains four host-accessible FIFOs: RX Status, RX Data, TX Status, and TX
Data FIFOs. The sizes Data FIFOs and the RX Status FIFO are configurable through the CSRs.
5.2.1
RX FIFO Ports
The RX Data Path contains two Read-Only FIFOs: RX Status and RX Data. The RX Status FIFO has
two ports at different address locations. The RX Status FIFO Port causes the top of the RX Status
FIFO to be “popped”, and is destructive. The RX Status FIFO PEEK Port allows the top of the RX
Status FIFO to be read without “popping” it.
The RX Data FIFO has a single port; reading data from this port always causes the top of the RX Data
FIFO to be “popped”. This port is aliased to 16 DWORD locations. The host may access the top of
the RX Data FIFO through any of these locations.
5.2.2
TX FIFO Ports
The TX Data Path consists of two FIFOs, TX Status and RX Data. The TX Status FIFO also has two
ports at different locations. When the TX Status FIFO Port is read, the top of the TX Status FIFO is
popped. When the TX Status FIFO PEEK Port is read, the top of the TX Status FIFO is not popped.
The TX data FIFO is Write Only. It is aliased to 16 DWORD locations. The host may access the top
of the TX Data FIFO through any of these locations.
SMSC LAN9221/LAN9221i
79
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3
System Control and Status Registers
Table 5.1, "Direct Address Register Map", lists the registers that are directly addressable by the host
bus.
Table 5.1 Direct Address Register Map
CONTROL AND STATUS REGISTERS
BASE ADDRESS
+ OFFSET
SYMBOL
50h
ID_REV
54h
IRQ_CFG
Main Interrupt Configuration
00000000h
58h
INT_STS
Interrupt Status
00000000h
5Ch
INT_EN
Interrupt Enable Register
00000000h
60h
RESERVED
Reserved for future use
-
64h
BYTE_TEST
Read-only byte order testing register
87654321h
68h
FIFO_INT
FIFO Level Interrupts
48000000h
6Ch
RX_CFG
Receive Configuration
00000000h
70h
TX_CFG
Transmit Configuration
00000000h
74h
HW_CFG
Hardware Configuration
00050000h
78h
RX_DP_CTL
RX Datapath Control
00000000h
7Ch
RX_FIFO_INF
Receive FIFO Information
00000000h
80h
TX_FIFO_INF
Transmit FIFO Information
00001200h
84h
PMT_CTRL
Power Management Control
00000000h
88h
GPIO_CFG
General Purpose IO Configuration
00000000h
8Ch
GPT_CFG
General Purpose Timer Configuration
0000FFFFh
90h
GPT_CNT
General Purpose Timer Count
0000FFFFh
94h
RESERVED
Reserved for future use
-
98h
WORD_SWAP
WORD SWAP Register
00000000h
9Ch
FREE_RUN
Free Run Counter
A0h
RX_DROP
RX Dropped Frames Counter
00000000h
A4h
MAC_CSR_CMD
MAC CSR Synchronizer Command (MAC
CSR’s are indexed through this register)
00000000h
A8h
MAC_CSR_DATA
MAC CSR Synchronizer Data
00000000h
ACh
AFC_CFG
Automatic Flow Control Configuration
00000000h
B0h
E2P_CMD
EEPROM Command
00000000h
B4h
E2P_DATA
EEPROM Data
00000000h
B8h - FCh
RESERVED
Reserved for future use
Revision 2.6 (12-04-08)
REGISTER NAME
Chip ID and Revision.
80
DATASHEET
DEFAULT
See Page 81.
-
-
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.1
ID_REV—Chip ID and Revision
Offset:
50h
Size:
32 bits
This register contains the ID and Revision fields for this design.
BITS
DESCRIPTION
TYPE
DEFAULT
31-16
Chip ID. This read-only field identifies this design
RO
9221h
15-0
Chip Revision
RO
0000h
5.3.2
IRQ_CFG—Interrupt Configuration Register
Offset:
54h
Size:
32 bits
This register configures and indicates the state of the IRQ signal.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
Interrupt Deassertion Interval (INT_DEAS). This field determines the
Interrupt Request Deassertion Interval in multiples of 10 microseconds.
R/W
0
Reserved
RO
-
14
Interrupt Deassertion Interval Clear (INT_DEAS_CLR). Writing a one
to this register clears the de-assertion counter in the IRQ Controller, thus
causing a new de-assertion interval to begin (regardless of whether or
not the IRQ Controller is currently in an active de-assertion interval).
SC
0
13
Interrupt Deassertion Status (INT_DEAS_STS). When set, this bit
indicates that interrupts are currently in a deassertion interval, and will
not be delivered to the IRQ pin. When this bit is clear, interrupts are not
currently in a deassertion interval, and will be delivered to the IRQ pin.
SC
0
12
Master Interrupt (IRQ_INT). This read-only bit indicates the state of the
internal IRQ line, regardless of the setting of the IRQ_EN bit, or the state
of the interrupt de-assertion function. When this bit is high, one of the
enabled interrupts is currently active.
RO
0
Reserved
RO
-
IRQ Enable (IRQ_EN) – This bit controls the final interrupt output to the
IRQ pin. When clear, the IRQ output is disabled and permanently
deasserted. This bit has no effect on any internal interrupt status bits.
R/W
0
Reserved
RO
-
Setting this field to zero causes the device to disable the INT_DEAS
Interval, reset the interval counter, and issue any pending interrupts. If a
new, non-zero value is written to this field, any subsequent interrupts will
obey the new setting.
Note:
23-15
11-9
8
7-5
SMSC LAN9221/LAN9221i
This field does not apply to the PME interrupt.
81
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
4
IRQ Polarity (IRQ_POL) – When cleared, enables the IRQ line to
function as an active low output. When set, the IRQ output is active high.
When IRQ is configured as an open-drain output this field is ignored,
and the interrupt output is always active low.
R/W
NASR
0
RO
-
R/W
NASR
0
3-1
0
Reserved
IRQ Buffer Type (IRQ_TYPE) – When cleared, enables IRQ to function
as an open-drain buffer for use in a Wired-Or Interrupt configuration.
When set, the IRQ output is a Push-Pull driver. When configured as an
open-drain output the IRQ_POL field is ignored, and the interrupt output
is always active low.
Revision 2.6 (12-04-08)
82
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.3
INT_STS—Interrupt Status Register
Offset:
58h
Size:
32 bits
This register contains the current status of the generated interrupts. Writing a 1 to the corresponding
bits acknowledges and clears the interrupt.
BITS
31
30-26
DESCRIPTION
Software Interrupt (SW_INT). This interrupt is generated when the
SW_INT_EN bit is set high. Writing a one clears this interrupt.
Reserved
TYPE
DEFAULT
R/WC
0
RO
-
25
TX Stopped (TXSTOP_INT). This interrupt is issued when STOP_TX bit
in TX_CFG is set, and the transmitter is halted.
R/WC
0
24
RX Stopped (RXSTOP_INT). This interrupt is issued when the receiver is
halted.
R/WC
0
23
RX Dropped Frame Counter Halfway (RXDFH_INT). This interrupt is
issued when the RX Dropped Frames Counter counts past its halfway
point (7FFFFFFFh to 80000000h).
R/WC
0
22
Reserved
RO
0
21
TX IOC Interrupt (TX_IOC). When a buffer with the IOC flag set has
finished being loaded into the TX FIFO, this interrupt is generated.
R/WC
0
20
RX DMA Interrupt (RXD_INT). This interrupt is issued when the amount
of data programmed in the RX DMA Count (RX_DMA_CNT) field of the
RX_CFG register has been transferred out of the RX FIFO.
R/WC
0
19
GP Timer (GPT_INT). This interrupt is issued when the General Purpose
timer wraps past zero to FFFFh.
R/WC
0
18
PHY (PHY_INT). Indicates a PHY Interrupt event.
RO
0
17
Power Management Event Interrupt (PME_INT). This interrupt is issued
when a Power Management Event is detected as configured in the
PMT_CTRL register. This interrupt functions independent of the PME
signal, and will still function if the PME signal is disabled. Writing a '1'
clears this bit regardless of the state of the PME hardware signal.
Notes:
„ Detection of a Power Management Event, and assertion of the PME
signal will not wakeup the LAN9221/LAN9221i. The LAN9221/LAN9221i
will only wake up when it detects a host write cycle of any data to the
BYTE_TEST register.
„ The Interrupt Deassertion interval does not apply to the PME interrupt.
R/WC
0
TX Status FIFO Overflow (TXSO). Generated when the TX Status
R/WC
0
15
Receive Watchdog Time-out (RWT). Interrupt is generated when a
R/WC
0
14
Receiver Error (RXE). Indicates that the receiver has encountered an
R/WC
0
13
Transmitter Error (TXE). When generated, indicates that the
R/WC
0
16
FIFO overflows.
packet larger than 2048 bytes has been received.
error. Please refer to Section 3.13.5, "Receiver Errors," on page 67 for a
description of the conditions that will cause an RXE.
transmitter has encountered an error. Please refer to Section 3.12.7,
"Transmitter Errors," on page 62, for a description of the conditions that
will cause a TXE.
SMSC LAN9221/LAN9221i
83
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
12:11
DESCRIPTION
Reserved
TYPE
DEFAULT
RO
-
10
TX Data FIFO Overrun Interrupt (TDFO). Generated when the TX data
FIFO is full, and another write is attempted.
R/WC
0
9
TX Data FIFO Available Interrupt (TDFA). Generated when the TX data
FIFO available space is greater than the programmed level.
R/WC
0
8
TX Status FIFO Full Interrupt (TSFF). Generated when the TX Status
FIFO is full.
R/WC
0
7
TX Status FIFO Level Interrupt (TSFL). Generated when the TX Status
FIFO reaches the programmed level.
R/WC
0
6
RX Dropped Frame Interrupt (RXDF_INT). This interrupt is issued
whenever a receive frame is dropped.
R/WC
0
5
Reserved
RO
-
4
RX Status FIFO Full Interrupt (RSFF). Generated when the RX Status
FIFO is full.
R/WC
0
3
RX Status FIFO Level Interrupt (RSFL). Generated when the RX Status
FIFO reaches the programmed level.
R/WC
0
GPIO [2:0] (GPIOx_INT). Interrupts are generated from the GPIO’s.
These interrupts are configured through the GPIO_CFG register.
R/WC
000
2-0
Revision 2.6 (12-04-08)
84
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.4
INT_EN—Interrupt Enable Register
Offset:
5Ch
Size:
32 bits
This register contains the interrupt masks for IRQ. Writing 1 to any of the bits enables the
corresponding interrupt as a source for IRQ. Bits in the INT_STS register will still reflect the status of
the interrupt source regardless of whether the source is enabled as an interrupt in this register.
BITS
TYPE
DEFAULT
Software Interrupt (SW_INT_EN)
R/W
0
Reserved
RO
-
25
TX Stopped Interrupt Enable (TXSTOP_INT_EN)
R/W
0
24
RX Stopped Interrupt Enable (RXSTOP_INT_EN)
R/W
0
23
RX Dropped Frame Counter Halfway Interrupt Enable (RXDFH_INT_EN).
R/W
0
22
Reserved
RO
0
21
TX IOC Interrupt Enable (TIOC_INT_EN)
R/W
0
20
RX DMA Interrupt (RXD_INT).
R/W
0
19
GP Timer (GPT_INT_EN)
R/W
0
18
PHY (PHY_INT_EN)
R/W
0
17
Power Management Event Interrupt Enable (PME_INT_EN)
R/W
0
16
TX Status FIFO Overflow (TXSO_EN)
R/W
0
15
Receive Watchdog Time-out Interrupt (RWT_INT_EN)
R/W
0
14
Receiver Error Interrupt (RXE_INT_EN)
R/W
0
13
Transmitter Error Interrupt (TXE_INT_EN)
R/W
0
Reserved
RO
-
10
TX Data FIFO Overrun Interrupt (TDFO_INT_EN)
R/W
0
9
TX Data FIFO Available Interrupt (TDFA_INT_EN)
R/W
0
8
TX Status FIFO Full Interrupt (TSFF_INT_EN)
R/W
0
7
TX Status FIFO Level Interrupt (TSFL_INT_EN)
R/W
0
6
RX Dropped Frame Interrupt Enable (RXDF_INT_EN)
R/W
0
5
Reserved
RO
-
4
RX Status FIFO Full Interrupt (RSFF_INT_EN)
R/W
0
3
RX Status FIFO Level Interrupt (RSFL_INT_EN)
R/W
0
GPIO [2:0] (GPIOx_INT_EN).
R/W
000
31
30:26
12:11
2-0
DESCRIPTION
SMSC LAN9221/LAN9221i
85
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.5
BYTE_TEST—Byte Order Test Register
Offset:
64h
Size:
32 bits
This register can be used to determine the byte ordering of the current configuration
BITS
31:0
5.3.6
DESCRIPTION
Byte Test
TYPE
DEFAULT
RO
87654321h
FIFO_INT—FIFO Level Interrupts
Offset:
68h
Size:
32 bits
This register configures the limits where the FIFO Controllers will generate system interrupts.
BITS
DESCRIPTION
TYPE
DEFAULT
31-24
TX Data Available Level. The value in this field sets the level, in number
of 64 Byte blocks, at which the TX FIFO Available interrupt (TFDA) will be
generated. When the TX data FIFO free space is greater than this value a
TX FIFO Available interrupt (TDFA) will be generated.
R/W
48h
23-16
TX Status Level. The value in this field sets the level, in number of
DWORDs, at which the TX Status FIFO Level interrupt (TSFL) will be
generated. When the TX Status FIFO used space is greater than this value
an TX Status FIFO Level interrupt (TSFL) will be generated.
R/W
00h
15-8
Reserved
RO
-
7-0
RX Status Level. The value in this field sets the level, in number of
DWORDs, at which the RX Status FIFO Level interrupt (RSFL) will be
generated. When the RX Status FIFO used space is greater than this value
an RX Status FIFO Level interrupt (RSFL) will be generated.
R/W
00h
Revision 2.6 (12-04-08)
86
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.7
RX_CFG—Receive Configuration Register
Offset:
6Ch
Size:
32 bits
This register controls the LAN9221/LAN9221i receive engine.
BITS
DESCRIPTION
TYPE
DEFAULT
31:30
RX End Alignment. This field specifies the alignment that must be
maintained on the last data transfer of a buffer. The LAN9221/LAN9221i
will add extra DWORDs of data up to the alignment specified in the table
below. The host is responsible for removing these extra DWORDs. This
mechanism can be used to maintain cache line alignment on host
processors.
Please refer to Table 5.2 for bit definitions
R/W
00b
Note:
The desired RX End Alignment must be set before reading a
packet. The RX end alignment can be changed between reading
receive packets, but must not be changed if the packet is
partially read.
29-28
Reserved
RO
-
27-16
RX DMA Count (RX_DMA_CNT). This 12-bit field indicates the amount
of data, in DWORDS, to be transferred out of the RX data FIFO before
asserting the RXD_INT. After being set, this field is decremented for each
DWORD of data that is read from the RX data FIFO. This field can be
overwritten with a new value before it reaches zero.
R/W
000h
15
Force RX Discard (RX_DUMP). This self-clearing bit clears the RX data
and status FIFOs of all pending data. When a ‘1’ is written, the RX data
and status pointers are cleared to zero.
SC
0
Note:
Please refer to section “Force Receiver Discard (Receiver
Dump)” on page 64 for a detailed description regarding the use
of RX_DUMP.
14-13
Reserved
RO
-
12-8
RX Data Offset (RXDOFF). This field controls the offset value, in bytes,
that is added to the beginning of an RX data packet. The start of the valid
data will be shifted by the number of bytes specified in this field. An offset
of 0-31 bytes is a valid number of offset bytes.
R/W
00000
RO
-
Note:
7-0
The two LSBs of this field (D[9:8]) must not be modified while
the RX is running. The receiver must be halted, and all data
purged before these two bits can be modified. The upper three
bits (DWORD offset) may be modified while the receiver is
running. Modifications to the upper bits will take affect on the
next DWORD read.
Reserved
Table 5.2 RX Alignment Bit Definitions
[31]
[30]
End Alignment
0
0
4-byte alignment
0
1
16-byte alignment
1
0
32-byte alignment
1
1
Reserved
SMSC LAN9221/LAN9221i
87
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.8
TX_CFG—Transmit Configuration Register
Offset:
70h
Size:
32 bits
This register controls the transmit functions on the LAN9221/LAN9221i Ethernet Controller.
BITS
TYPE
DEFAULT
Reserved.
RO
-
15
Force TX Status Discard (TXS_DUMP). This self-clearing bit clears the TX
status FIFO of all pending status DWORD’s. When a ‘1’ is written, the TX
status pointers are cleared to zero.
SC
0
14
Force TX Data Discard (TXD_DUMP). This self-clearing bit clears the TX
data FIFO of all pending data. When a ‘1’ is written, the TX data pointers
are cleared to zero.
SC
0
Reserved
RO
-
TX Status Allow Overrun (TXSAO). When this bit is cleared, data
transmission is suspended if the TX Status FIFO becomes full. Setting this
bit high allows the transmitter to continue operation with a full TX Status
FIFO.
R/W
0
31-16
13-3
2
DESCRIPTION
Note:
This bit does not affect the operation of the TX Status FIFO Full
interrupt.
1
Transmitter Enable (TX_ON). When this bit is set (1), the transmitter is
enabled. Any data in the TX FIFO will be sent. This bit is cleared
automatically when STOP_TX is set and the transmitter is halted.
R/W
0
0
Stop Transmitter (STOP_TX). When this bit is set (1), the transmitter will
finish the current frame, and will then stop transmitting. When the transmitter
has stopped this bit will clear. All writes to this bit are ignored while this bit
is high.
SC
0
Revision 2.6 (12-04-08)
88
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.9
HW_CFG—Hardware Configuration Register
Offset:
74h
Size:
32 bits
Note: The transmitter and receiver must be stopped before writing to this register. Refer to Section
3.12.8, "Stopping and Starting the Transmitter," on page 62 and Section 3.13.4, "Stopping and
Starting the Receiver," on page 67 for details on stopping the transmitter and receiver.
BITS
DESCRIPTION
TYPE
DEFAULT
31
Reserved
RO
-
30
Reserved
RO
-
29
FIFO Port Endian Ordering (FPORTEND). This control bit determines the
endianess of RX and TX data FIFO host accesses when accessed through
the RX/TX Data FIFO ports, including the alias addresses (any access from
00h to 3Ch). When this bit is cleared, data FIFO port accesses utilize little
endian byte ordering. When this bit is set, data FIFO port accesses utilize
big endian byte ordering. Please refer to section Section 3.7.3, "Mixed
Endian Support," on page 35 for more information on this feature.
R/W
NASR
0
28
Direct FIFO Access Endian Ordering (FSELEND). This control bit
determines the endianess of RX and TX data FIFO host accesses when
accessed using the FIFO_SEL signal. When this bit is cleared, FIFO_SEL
accesses utilize little endian byte ordering. When this bit is set, FIFO_SEL
accesses utilize big endian byte ordering. Please refer to section Section
3.7.3, "Mixed Endian Support," on page 35 for more information on this
feature.
R/W
NASR
0
Reserved
RO
-
AMDIX_EN Strap State. This read-only bit reflects the state of the
AMDIX_EN strap pin (pin 73). This pin can be overridden by PHY Registers
27.15 and 27.13
RO
AMDIX
Strap
Pin
Reserved
RO
Must Be One (MBO). This bit must be set to “1” for normal device
operation.
R/W
0
TX FIFO Size (TX_FIF_SZ). Sets the size of the TX FIFOs in 1KB values
to a maximum of 14KB. The TX Status FIFO consumes 512 bytes of the
space allocated by TX_FIF_SIZ, and the TX data FIFO consumes the
remaining space specified by TX_FIF_SZ. The minimum size of the TX
FIFOs is 2KB (TX data and status combined). The TX data FIFO is used for
both TX data and TX commands.
R/W
5h
Reserved
RO
-
Soft Reset Timeout (SRST_TO). If a software reset is attempted when the PHY
RO
0
27-25
24
23-21
20
16-19
The RX Status and data FIFOs consume the remaining space, which is
equal to 16KB – TX_FIF_SIZ. See Section 5.3.9.1, "Allowable settings for
Configurable FIFO Memory Allocation," on page 91 for more information.
15-2
1
is not in the operational state (RX_CLK and TX_CLK running), the reset will not
complete and the soft reset operation will timeout and this bit will be set to a ‘1’. The
host processor must correct the problem and issue another soft reset.
SMSC LAN9221/LAN9221i
89
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
0
Soft Reset (SRST). Writing 1 generates a software initiated reset. This reset
generates a full reset of the MAC CSR’s. The SCSR’s (system command
and status registers) are reset except for any NASR bits. Soft reset also
clears any TX or RX errors (TXE/RXE). This bit is self-clearing.
SC
0
Notes:
„ Do not attempt a soft reset unless the PHY is fully awake and operational.
After a PHY reset, or when returning from a reduced power state, the PHY
must given adequate time to return to the operational state before a soft
reset can be issued.
„ The LAN9221/LAN9221i must always be read at least once after powerup, reset, or upon return from a power-saving state or write operations will
not function.
Revision 2.6 (12-04-08)
90
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.9.1
Allowable settings for Configurable FIFO Memory Allocation
TX and RX FIFO space is configurable through the CSR - HW_CFG register defined above. The user
must select the FIFO allocation by setting the TX FIFO Size (TX_FIF_SZ) field in the hardware
configuration (HW_CFG) register. The TX_FIF_SZ field selects the total allocation for the TX data path,
including the TX Status FIFO size. The TX Status FIFO size is fixed at 512 Bytes (128 TX Status
DWORDs). The TX Status FIFO length is subtracted from the total TX FIFO size with the remainder
being the TX data FIFO Size. Note that TX data FIFO space includes both commands and payload
data.
RX FIFO Size is the remainder of the unallocated FIFO space (16384 bytes – TX FIFO Size). The RX
Status FIFO size is always equal to 1/16 of the RX FIFO Size. The RX Status FIFO length is subtracted
from the total RX FIFO size with the remainder being the RX data FIFO Size.
For example, if TX_FIF_SZ = 6 then:
Total TX FIFO Size = 6144 Bytes (6KB)
TX Status FIFO Size = 512 Bytes (Fixed)
TX Data FIFO Size = 6144 – 512 = 5632 Bytes
RX FIFO Size = 16384 – 6144 = 10240 Bytes (10KB)
RX Status FIFO Size = 10240 / 16 = 640 Bytes (160 RX Status DWORDs)
RX Data FIFO Size = 10240 – 640 = 9600 Bytes
Table 5.3 shows every valid setting for the TX_FIF_SZ field. Note that settings not shown in this table
are reserved and should not be used.
Note: The RX data FIFO is considered full 4 DWORDs before the length that is specified in the
HW_CFG register.
Table 5.3 Valid TX/RX FIFO Allocations
TX_FIF_SZ
TX DATA FIFO
SIZE (BYTES)
TX STATUS FIFO
SIZE (BYTES)
RX DATA FIFO
SIZE (BYTES)
RX STATUS FIFO
SIZE (BYTES)
2
1536
512
13440
896
3
2560
512
12480
832
4
3584
512
11520
768
5
4608
512
10560
704
6
5632
512
9600
640
7
6656
512
8640
576
8
7680
512
7680
512
9
8704
512
6720
448
10
9728
512
5760
384
11
10752
512
4800
320
12
11776
512
3840
256
13
12800
512
2880
192
14
13824
512
1920
128
SMSC LAN9221/LAN9221i
91
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
In addition to the host-accessible FIFOs, the MAC Interface Layer (MIL) contains an additional 2K
bytes of TX, and 128 bytes of RX FIFO buffering. These sizes are fixed, and cannot be adjusted by
the host.
As space in the TX MIL (Mac Interface Layer) FIFO frees, data is moved into it from the TX data FIFO.
Depending on the size of the frames to be transmitted, the MIL can hold up to two Ethernet frames.
This is in addition to any TX data that may be queued in the TX data FIFO.
Conversely, as data is received by the LAN9221/LAN9221i, it is moved from the MAC to the RX MIL
FIFO, and then into the RX data FIFO. When the RX data FIFO fills up, data will continue to collect
in the RX MIL FIFO. If the RX MIL FIFO fills up and overruns, subsequent RX frames will be lost until
room is made in the RX data FIFO. For each frame of data that is lost, the RX Dropped Frames
Counter (RX_DROP) is incremented.
RX and TX MIL FIFO levels are not visible to the host processor. RX and TX MIL FIFOs operate
independent of the TX data and RX data and status FIFOs. FIFO levels set for the RX and TX data
and Status FIFOs do not take into consideration the MIL FIFOs.
5.3.10
RX_DP_CTRL—Receive Datapath Control Register
Offset:
78h
Size:
32 bits
This register is used to discard unwanted receive frames.
BITS
DESCRIPTION
TYPE
DEFAULT
31
RX Data FIFO Fast Forward (RX_FFWD): Writing a ‘1’ to this bit causes
the RX data FIFO to fast-forward to the start of the next frame. This bit will
remain high until the RX data FIFO fast-forward operation has completed.
No reads should be issued to the RX data FIFO while this bit is high.
R/W
SC
0b
RO
-
Note:
30-0
Please refer to section “Receive Data FIFO Fast Forward” on
page 64 for detailed information regarding the use of RX_FFWD.
Reserved
Revision 2.6 (12-04-08)
92
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.11
RX_FIFO_INF—Receive FIFO Information Register
Offset:
7Ch
Size:
32 bits
This register contains the used space in the receive FIFOs of the LAN9221/LAN9221i Ethernet
Controller.
BITS
DESCRIPTION
TYPE
DEFAULT
31-24
Reserved
RO
-
23-16
RX Status FIFO Used Space (RXSUSED). Indicates the amount of space
in DWORDs, used in the RX Status FIFO.
RO
00h
15-0
RX Data FIFO Used Space (RXDUSED).). Reads the amount of space in
bytes, used in the RX data FIFO. For each receive frame, this field is
incremented by the length of the receive data rounded up to the nearest
DWORD (if the payload does not end on a DWORD boundary).
RO
0000h
5.3.12
TX_FIFO_INF—Transmit FIFO Information Register
Offset:
80h
Size:
32 bits
This register contains the free space in the transmit data FIFO and the used space in the transmit
status FIFO in the LAN9221/LAN9221i.
BITS
DESCRIPTION
TYPE
DEFAULT
31-24
Reserved
RO
-
23-16
TX Status FIFO Used Space (TXSUSED). Indicates the amount of space
in DWORDS used in the TX Status FIFO.
RO
00h
15-0
TX Data FIFO Free Space (TDFREE). Reads the amount of space in bytes,
available in the TX data FIFO. The application should never write more data
than is available, as indicated by this value.
RO
1200h
SMSC LAN9221/LAN9221i
93
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.13
PMT_CTRL— Power Management Control Register
Offset:
84h
Size:
32 bits
This register controls the Power Management features. This register can be read while the
LAN9221/LAN9221i is in a power saving mode.
Note: The LAN9221/LAN9221i must always be read at least once after power-up, reset, or upon
return from a power-saving state or write operations will not function.
BITS
DESCRIPTION
TYPE
DEFAULT
31:14
RESERVED
RO
-
13-12
Power Management Mode (PM_MODE) – These bits set the
LAN9221/LAN9221i into the appropriate Power Management mode. Special
care must be taken when modifying these bits.
SC
00b
Encoding:
00b – D0 (normal operation)
01b – D1 (wake-up frame and magic packet detection are enabled)
10b – D2 (can perform energy detect)
11b – RESERVED - Do not set in this mode
Note:
When the LAN9221/LAN9221i is in any of the reduced power
modes, a write of any data to the BYTE_TEST register will wakeup the device. DO NOT PERFORM WRITES TO OTHER
ADDRRESSES while the READY bit in this register is cleared.
11
RESERVED
RO
-
10
PHY Reset (PHY_RST) – Writing a ‘1’ to this bit resets the PHY. The internal
logic automatically holds the PHY reset for a minimum of 100us. When the
PHY is released from reset, this bit is automatically cleared. All writes to this
bit are ignored while this bit is high.
SC
0b
9
Wake-On-Lan Enable (WOL_EN) – When set, the PME signal (if enabled
with PME_EN) will be asserted in accordance with the PME_IND bit upon a
WOL event. When set, the PME_INT will also be asserted upon a WOL
event, regardless of the setting of the PME_EN bit.
R/W
0b
8
Energy-Detect Enable (ED_EN) - When set, the PME signal (if enabled with
PME_EN) will be asserted in accordance with the PME_IND bit upon an
Energy-Detect event. When set, the PME_INT will also be asserted upon an
Energy Detect event, regardless of the setting of the PME_EN bit.
R/W
0b
7
RESERVED
RO
-
6
PME Buffer Type (PME_TYPE) – When cleared, enables PME to function
as an open-drain buffer for use in a Wired-Or configuration. When set, the
PME output is a Push-Pull driver. When configured as an open-drain output
the PME_POL field is ignored, and the output is always active low.
R/W
NASR
0b
Revision 2.6 (12-04-08)
94
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
5-4
DESCRIPTION
WAKE-UP Status (WUPS) – This field indicates the cause of a wake-up
event detection as follows
TYPE
DEFAULT
R/WC
00
R/W
0b
00b -- No wake-up event detected
01b -- Energy detected
10b -- Wake-up frame or magic packet detected
11b -- Indicates multiple events occurred
WUPS bits are cleared by writing a ‘1’ to the appropriate bit. The device must
return to the D0 state (READY bit set) before these bits can be cleared.
Note:
3
In order to clear this bit, it is required that all event sources be
cleared as well. The event sources are described in Figure 3.12
PME and PME_INT Signal Generationon page 47.
PME indication (PME_IND). The PME signal can be configured as a pulsed
output or a static signal, which is asserted upon detection of a wake-up
event.
When set, the PME signal will pulse active for 50mS upon detection of a
wake-up event.
When clear, the PME signal is driven continuously upon detection of a wakeup event.
The PME signal can be deactivated by clearing the WUPS bits, or by
clearing the appropriate enable (refer to Section 3.10.2.3, "Power
Management Event Indicators," on page 47).
2
PME Polarity (PME_POL). This bit controls the polarity of the PME signal.
When set, the PME output is an active high signal. When reset, it is active
low. When PME is configured as an open-drain output this field is ignored,
and the output is always active low.
R/W
NASR
0b
1
PME Enable (PME_EN). When set, this bit enables the external PME signal.
This bit does not affect the PME interrupt (PME_INT).
R/W
0b
0
Device Ready (READY). When set, this bit indicates that
LAN9221/LAN9221i is ready to be accessed. This register can be read when
LAN9221/LAN9221i is in any power management mode. Upon waking from
any power management mode, including power-up, the host processor can
interrogate this field as an indication when LAN9221/LAN9221i has stabilized
and is fully alive. Reads and writes of any other address are invalid until this
bit is set.
RO
-
Note:
With the exception of HW_CFG and PMT_CTRL, read access to
any internal resources is forbidden while the READY bit is cleared.
Note:
On power-up, this bit can be polled to indicate when a valid soft
reset (SRST) can be performed.
SMSC LAN9221/LAN9221i
95
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.14
GPIO_CFG—General Purpose IO Configuration Register
Offset:
88h
Size:
32 bits
This register configures the GPIO and LED functions.
BITS
TYPE
DEFAULT
Reserved
RO
-
LED[3:1] enable (LEDx_EN). A ‘1’ sets the associated pin as an LED
output. When cleared low, the pin functions as a GPIO signal.
LED1/GPIO0 – bit 28
LED2/GPIO1 – bit 29
LED3/GPIO2 – bit 30
R/W
000
Reserved
RO
-
GPIO Interrupt Polarity 0-2 (GPIO_INT_POL). When set high, a high logic
level on the corresponding GPIO pin will set the corresponding INT_STS
register bit. When cleared low, a low logic level on the corresponding GPIO
pin will set the corresponding INT_STS register bit.
GPIO Interrupts must also be enabled in GPIOx_INT_EN in the INT_EN
register.
R/W
000
Reserved
RO
-
EEPROM Enable (EEPR_EN). The value of this field determines the
function of the external EEDIO and EECLK:
Please refer to Table 5.4 for the EEPROM Enable bit function definitions.
R/W
000
Reserved
RO
-
18:16
GPIO Buffer Type 0-2 (GPIOBUFn). When set, the output buffer for the
corresponding GPIO signal is configured as a push/pull driver. When
cleared, the corresponding GPIO set configured as an open-drain driver.
GPIO0 – bit 16
GPIO1 – bit 17
GPIO2 – bit 18
R/W
000
15:11
Reserved
RO
-
10:8
GPIO Direction 0-2 (GPDIRn). When set, enables the corresponding GPIO
as output. When cleared the GPIO is enabled as an input.
GPIO0 – bit 8
GPIO1 – bit 9
GPIO2 – bit 10
R/W
0000
7:5
Reserved
RO
-
31
30:28
27
26:24
DESCRIPTION
GPIO0 – bit 24
GPIO1 – bit 25
GPIO2 – bit 26
Note:
23
22:20
Note:
19
Revision 2.6 (12-04-08)
GPIO inputs must be active for greater than 40nS to be recognized
as interrupt inputs.
The host must not change the function of the EEDIO and EECLK
pins when an EEPROM read or write cycle is in progress. Do not
use reserved settings.
96
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
4:3
GPO Data 3-4 (GPODn). The value written is reflected on GPOn.
GPO3 – bit 3
GPO4 – bit 4
R/W
00
2:0
GPIO Data 0-2 (GPIODn). When enabled as an output, the value written is
reflected on GPIOn. When read, GPIOn reflects the current state of the
corresponding GPIO pin.
GPIO0 – bit 0
GPIO1 – bit 1
GPIO2 – bit 2
R/W
000
Table 5.4 EEPROM Enable Bit Definitions
[22]
[21]
[20]
EEDIO FUNCTION
EECLK FUNCTION
0
0
0
EEDIO
EECLK
0
0
1
GPO3
GPO4
0
1
0
0
1
1
1
0
0
1
0
1
TX_EN
GPO4
1
1
0
TX_EN
RX_DV
1
1
1
TX_CLK
RX_CLK
5.3.15
Reserved
GPO3
RX_DV
Reserved
GPT_CFG-General Purpose Timer Configuration Register
Offset:
8Ch
Size:
32 bits
This register configures the General Purpose timer. The GP Timer can be configured to generate host
interrupts at intervals defined in this register.
BITS
TYPE
DEFAULT
Reserved
RO
-
GP Timer Enable (TIMER_EN). When a one is written to this bit the GP
Timer is put into the run state. When cleared, the GP Timer is halted. On
the 1 to 0 transition of this bit the GPT_LOAD field will be preset to FFFFh.
R/W
0
28-16
Reserved
RO
-
15-0
General Purpose Timer Pre-Load (GPT_LOAD). This value is pre-loaded
into the GP-Timer.
R/W
FFFFh
31-30
29
DESCRIPTION
SMSC LAN9221/LAN9221i
97
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.16
GPT_CNT-General Purpose Timer Current Count Register
Offset:
90h
Size:
32 bits
This register reflects the current value of the GP Timer.
BITS
DESCRIPTION
TYPE
DEFAULT
31-16
Reserved
RO
-
15-0
General Purpose Timer Current Count (GPT_CNT). This 16-bit field
reflects the current value of the GP Timer.
RO
FFFFh
5.3.17
WORD_SWAP—Word Swap Control
Offset:
98h
Size:
32 bits
This register controls how words from the host data bus are mapped to the CSRs and Data FIFOs
inside the LAN9221/LAN9221i. The LAN9221/LAN9221i always sends data from the Transmit Data
FIFO to the network so that the low order word is sent first, and always receives data from the network
to the Receive Data FIFO so that the low order word is received first.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Word Swap. If this field is set to 00000000h, or anything except
0xFFFFFFFFh, the LAN9221/LAN9221i maps words with address bit A[1]=1
to the high order words of the CSRs and Data FIFOs, and words with
address bit A[1]=0 to the low order words of the CSRs and Data FIFOs. If
this field is set to 0xFFFFFFFFh, the LAN9221/LAN9221i maps words with
address bit A[1]=1 to the low order words of the CSRs and Data FIFOs, and
words with address bit A[1]=0 to the high order words of the CSRs and Data
FIFOs.
R/W
NASR
00000000h
Note:
Revision 2.6 (12-04-08)
Word swap is used in conjunction with the mixed endian
functionality to determine the final byte ordering. Refer to Section
3.7.3, "Mixed Endian Support" for more information.
98
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.18
FREE_RUN—Free-Run 25MHz Counter
Offset:
9Ch
Size:
32 bits
This register reflects the value of the free-running 25MHz counter.
BITS
31:0
5.3.19
DESCRIPTION
TYPE
DEFAULT
RO
-
Free Running SCLK Counter (FR_CNT):
Note:
This field reflects the value of a free-running 32-bit counter. At reset
the counter starts at zero and is incremented for every 25MHz
cycle. When the maximum count has been reached the counter will
rollover. Since the bus interface is 16-bits wide, and this is a 32-bit
counter, the count value is latched on the first read. The
FREE_RUN counter can take up to 160nS to clear after a reset
event.
Note:
This counter will run regardless of the power management states
D0, D1 or D2.
RX_DROP– Receiver Dropped Frames Counter
Offset:
A0h
Size:
32 bits
This register indicates the number of receive frames that have been dropped.
BITS
DESCRIPTION
TYPE
DEFAULT
31-0
RX Dropped Frame Counter (RX_DFC). This counter is incremented every
time a receive frame is dropped. RX_DFC is cleared on any read of this
register.
RC
00000000h
An interrupt can be issued when this counter passes through its halfway
point (7FFFFFFFh to 80000000h).
SMSC LAN9221/LAN9221i
99
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.20
MAC_CSR_CMD – MAC CSR Synchronizer Command Register
Offset:
A4h
Size:
32 bits
This register is used to control the read and write operations with the MAC CSR’s
BITS
DESCRIPTION
TYPE
DEFAULT
31
CSR Busy. When a 1 is written into this bit, the read or write operation is
performed to the specified MAC CSR. This bit will remain set until the
operation is complete. In the case of a read this means that the host can
read valid data from the data register. The MAC_CSR_CMD and
MAC_CSR_DATA registers should not be modified until this bit is cleared.
SC
0
30
R/nW. When set, this bit indicates that the host is requesting a read
operation. When clear, the host is performing a write.
R/W
0
29-8
Reserved.
RO
-
7-0
CSR Address. The 8-bit value in this field selects which MAC CSR will be
accessed with the read or write operation.
R/W
00h
5.3.21
MAC_CSR_DATA – MAC CSR Synchronizer Data Register
Offset:
A8h
Size:
32 bits
This register is used in conjunction with the MAC_CSR_CMD register to perform read and write
operations with the MAC CSR’s
BITS
31-0
DESCRIPTION
MAC CSR Data. Value read from or written to the MAC CSR’s.
Revision 2.6 (12-04-08)
100
DATASHEET
TYPE
DEFAULT
R/W
00000000h
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.22
AFC_CFG – Automatic Flow Control Configuration Register
Offset:
ACh
Size:
32 bits
This register configures the mechanism that controls both the automatic, and software-initiated
transmission of pause frames and back pressure.
Note: The LAN9221/LAN9221i will not transmit pause frames or assert back pressure if the
transmitter is disabled.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
Reserved
RO
-
23:16
Automatic Flow Control High Level (AFC_HI). Specifies, in multiples of
64 bytes, the level at which flow control will trigger. When this limit is
reached the chip will apply back pressure or will transmit a pause frame as
programmed in bits [3:0] of this register.
R/W
00h
R/W
00h
During full-duplex operation only a single pause frame is transmitted when
this level is reached. The pause time transmitted in this frame is
programmed in the FCPT field of the FLOW register in the MAC CSR space.
During half-duplex operation each incoming frame that matches the criteria
in bits [3:0] of this register will be jammed for the period set in the
BACK_DUR field.
15:8
Automatic Flow Control Low Level (AFC_LO). Specifies, in multiples of
64 bytes, the level at which a pause frame is transmitted with a pause time
setting of zero. When the amount of data in the RX data FIFO falls below
this level the pause frame is transmitted. A pause time value of zero
instructs the other transmitting device to immediately resume transmission.
The zero time pause frame will only be transmitted if the RX data FIFO had
reached the AFC_HI level and a pause frame was sent. A zero pause time
frame is sent whenever automatic flow control in enabled in bits [3:0] of this
register.
Note:
When automatic flow control is enabled the AFC_LO setting must
always be less than the AFC_HI setting.
7:4
Backpressure Duration (BACK_DUR). When the LAN9221/LAN9221i
automatically asserts back pressure, it will be asserted for this period of
time. This field has no function and is not used in full-duplex mode. Please
refer to Table 5.5, describing Backpressure Duration bit mapping for more
information.
R/W
0h
3
Flow Control on Multicast Frame (FCMULT). When this bit is set, the
LAN9221/LAN9221i will assert back pressure when the AFC level is
reached and a multicast frame is received. This field has no function in fullduplex mode.
R/W
0
2
Flow Control on Broadcast Frame (FCBRD). When this bit is set, the
LAN9221/LAN9221i will assert back pressure when the AFC level is
reached and a broadcast frame is received. This field has no function in fullduplex mode.
R/W
0
1
Flow Control on Address Decode (FCADD). When this bit is set, the
LAN9221/LAN9221i will assert back pressure when the AFC level is
reached and a frame addressed to the LAN9221/LAN9221i is received. This
field has no function in full-duplex mode.
R/W
0
SMSC LAN9221/LAN9221i
101
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
0
Flow Control on Any Frame (FCANY). When this bit is set, the
LAN9221/LAN9221i will assert back pressure, or transmit a pause frame
when the AFC level is reached and any frame is received. Setting this bit
enables full-duplex flow control when the LAN9221/LAN9221i is operating in
full-duplex mode.
R/W
0
When this mode is enabled during half-duplex operation, the Flow Controller
does not decode the MAC address and will send a pause frame upon
receipt of a valid preamble (i.e., immediately at the beginning of the next
frame after the RX data FIFO level is reached).
When this mode is enabled during full-duplex operation, the Flow Controller
will immediately instruct the MAC to send a pause frame when the RX data
FIFO level is reached. The MAC will queue the pause frame transmission
for the next available window.
Setting this bit overrides bits [3:1] of this register.
Table 5.5 Backpressure Duration Bit Mapping
BACKPRESSURE DURATION
[19:16]
100Mbs Mode
10Mbs Mode
0h
5uS
7.2uS
1h
10uS
12.2uS
2h
15uS
17.2uS
3h
25uS
27.2uS
4h
50uS
52.2uS
5h
100uS
102.2uS
6h
150uS
152.2uS
7h
200uS
202.2uS
8h
250uS
252.2uS
9h
300uS
302.2uS
Ah
350uS
352.2uS
Bh
400uS
402.2uS
Ch
450uS
452.2uS
Dh
500uS
502.2uS
Eh
550uS
552.2uS
Fh
600uS
602.2uS
Revision 2.6 (12-04-08)
102
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.3.23
E2P_CMD – EEPROM Command Register
Offset:
B0h
Size:
32 bits
This register is used to control the read and write operations with the Serial EEPROM.
BITS
DESCRIPTION
TYPE
DEFAULT
31
EPC Busy: When a 1 is written into this bit, the operation specified in the
EPC command field is performed at the specified EEPROM address. This
bit will remain set until the operation is complete. In the case of a read this
means that the host can read valid data from the E2P data register. The
E2P_CMD and E2P_DATA registers should not be modified until this bit is
cleared. In the case where a write is attempted and an EEPROM is not
present, the EPC Busy remains busy until the EPC Time-out occurs. At that
time the busy bit is cleared.
SC
0
Note:
EPC busy will be high immediately following power-up or reset.
After the EEPROM controller has finished reading (or attempting to
read) the MAC address from the EEPROM the EPC Busy bit is
cleared.
SMSC LAN9221/LAN9221i
103
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
30-28
EPC command. This field is used to issue commands to the EEPROM
controller. The EPC will execute commands when the EPC Busy bit is set.
A new command must not be issued until the previous command completes.
This field is encoded as follows:
R/W
0
RO
-
[30]
[29]
[28]
OPERATION
0
0
0
READ
0
0
1
EWDS
0
1
0
EWEN
0
1
1
WRITE
1
0
0
WRAL
1
0
1
ERASE
1
1
0
ERAL
1
1
1
Reload
READ (Read Location): This command will cause a read of the EEPROM
location pointed to by EPC Address. The result of the read is available in
the E2P_DATA register.
EWDS (Erase/Write Disable): After issued, the EEPROM will ignore erase
and write commands. To re-enable erase/write operations issue the EWEN
command.
EWEN (Erase/Write Enable): Enables the EEPROM for erase and write
operations. The EEPROM will allow erase and write operations until the
Erase/Write Disable command is sent, or until power is cycled.
Note:
The EEPROM device will power-up in the erase/write-disabled
state. Any erase or write operations will fail until an Erase/Write
Enable command is issued.
WRITE (Write Location): If erase/write operations are enabled in the
EEPROM, this command will cause the contents of the E2P_DATA register
to be written to the EEPROM location selected by the EPC Address field.
WRAL (Write All): If erase/write operations are enabled in the EEPROM,
this command will cause the contents of the E2P_DATA register to be
written to every EEPROM memory location.
ERASE (Erase Location): If erase/write operations are enabled in the
EEPROM, this command will erase the location selected by the EPC
Address field.
ERAL (Erase All): If erase/write operations are enabled in the EEPROM,
this command will initiate a bulk erase of the entire EEPROM.
RELOAD (MAC Address Reload): Instructs the EEPROM controller to
reload the MAC address from the EEPROM. If a value of 0xA5 is not found
in the first address of the EEPROM, the EEPROM is assumed to be unprogrammed and MAC Address Reload operation will fail. The “MAC
Address Loaded” bit indicates a successful load of the MAC address.
27-10
Reserved.
Revision 2.6 (12-04-08)
104
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
9
DESCRIPTION
EPC Time-out. If an EEPROM operation is performed, and there is no
response from the EEPROM within 30mS, the EEPROM controller will timeout and return to its idle state. This bit is set when a time-out occurs
indicating that the last operation was unsuccessful.
Note:
8
7-0
TYPE
DEFAULT
R/WC
0
R/WC
-
R/W
00h
If the EEDIO signal pin is externally pulled-high, EPC commands
will not time out if the EEPROM device is missing. In this case the
EPC Busy bit will be cleared as soon as the command sequence
is complete. It should also be noted that the ERASE, ERAL,
WRITE and WRAL commands are the only EPC commands that
will time-out if an EEPROM device is not present -and- the EEDIO
signal is pulled low
MAC Address Loaded. When set, this bit indicates that a valid EEPROM
was found, and that the MAC address programming has completed
normally. This bit is set after a successful load of the MAC address after
power-up, or after a RELOAD command has completed
EPC Address. The 8-bit value in this field is used by the EEPROM
Controller to address the specific memory location in the Serial EEPROM.
This is a Byte aligned address.
5.3.24
E2P_DATA – EEPROM Data Register
Offset:
B4h
Size:
32 bits
This register is used in conjunction with the E2P_CMD register to perform read and write operations
with the Serial EEPROM.
BITS
31-8
7:0
DESCRIPTION
TYPE
DEFAULT
Reserved
RO
-
EEPROM Data. Value read from or written to the EEPROM.
R/W
00h
SMSC LAN9221/LAN9221i
105
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4
MAC Control and Status Registers
These registers are located in the MAC module and are accessed indirectly through the MAC-CSR
synchronizer port. Table 5.6, "MAC CSR Register Map", shown below, lists the MAC registers that are
accessible through the indexing method using the MAC_CSR_CMD and MAC_CSR_DATA registers
(see sections MAC_CSR_CMD – MAC CSR Synchronizer Command Register and MAC_CSR_DATA
– MAC CSR Synchronizer Data Register).
Table 5.6 MAC CSR Register Map
MAC CONTROL AND STATUS REGISTERS
INDEX
SYMBOL
1
MAC_CR
2
REGISTER NAME
DEFAULT
MAC Control Register
00040000h
ADDRH
MAC Address High
0000FFFFh
3
ADDRL
MAC Address Low
FFFFFFFFh
4
HASHH
Multicast Hash Table High
00000000h
5
HASHL
Multicast Hash Table Low
00000000h
6
MII_ACC
MII Access
00000000h
7
MII_DATA
MII Data
00000000h
8
FLOW
Flow Control
00000000h
9
VLAN1
VLAN1 Tag
00000000h
A
VLAN2
VLAN2 Tag
00000000h
B
WUFF
Wake-up Frame Filter
00000000h
C
WUCSR
Wake-up Control and Status
00000000h
D
COE_CR
Checksum Offload Engine Control
00000000h
Revision 2.6 (12-04-08)
106
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.1
MAC_CR—MAC Control Register
Offset:
1
Attribute:
R/W
Default Value:
00040000h
Size:
32 bits
This register establishes the RX and TX operation modes and controls for address filtering and packet
filtering.
BITS
DESCRIPTION
31
Receive All Mode (RXALL). When set, all incoming packets will be received and passed on to the
address filtering Function for processing of the selected filtering mode on the received frame. Address
filtering then occurs and is reported in Receive Status. When reset, only frames that pass Destination
Address filtering will be sent to the Application.
30-24
Reserved
23
Disable Receive Own (RCVOWN). When set, the MAC disables the reception of frames when the
MII TX_EN signal is asserted. The MAC blocks the transmitted frame on the receive path. When reset,
the MAC receives all packets the PHY gives, including those transmitted by the MAC.This bit should
be reset when the Full Duplex Mode bit is set.
22
Reserved
21
Loopback operation Mode (LOOPBK). Selects the loop back operation modes for the MAC. This is
only for full duplex mode
1’b0: Normal: No feedback
1’b1: Internal: Through MII
In internal loopback mode, the TX frame is received by the Internal MII interface, and sent back to
the MAC without being sent to the PHY.
Note:
When enabling or disabling the loopback mode it can take up to 10μs for the mode change
to occur. The transmitter and receiver must be stopped and disabled when modifying the
LOOPBK bit. The transmitter or receiver should not be enabled within10μs of modifying the
LOOPBK bit.
20
Full Duplex Mode (FDPX). When set, the MAC operates in Full-Duplex mode, in which it can transmit
and receive simultaneously. In Full-Duplex mode, the heartbeat check is disabled and the heartbeat
fail status should thus be ignored.
19
Pass All Multicast (MCPAS). When set, indicates that all incoming frames with a Multicast destination
address (first bit in the destination address field is 1) are received. Incoming frames with physical
address (Individual Address/Unicast) destinations are filtered and received only if the address matches
the MAC Address.
18
Promiscuous Mode (PRMS). When set, indicates that any incoming frame is received regardless of
its destination address.
17
Inverse filtering (INVFILT). When set, the address check Function operates in Inverse filtering mode.
This is valid only during Perfect filtering mode.
16
Pass Bad Frames (PASSBAD). When set, all incoming frames that passed address filtering are
received, including runt frames and collided frames.
15
Hash Only Filtering mode (HO). When set, the address check Function operates in the Imperfect
Address Filtering mode both for physical and multicast addresses
14
Reserved
SMSC LAN9221/LAN9221i
107
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
13
Hash/Perfect Filtering Mode (HPFILT). When reset (0), the LAN9221/LAN9221i will implement a
perfect address filter on incoming frames according the address specified in the MAC address register.
When set (1), the address check Function does imperfect address filtering of multicast incoming
frames according to the hash table specified in the multicast hash table register.
If the Hash Only Filtering mode (HO) bit is set (1), then the physical (IA) are imperfect filtered too. If
the Hash Only Filtering mode (HO) bit is reset (0), then the IA addresses are perfect address filtered
according to the MAC Address register
12
Late Collision Control (LCOLL). When set, enables retransmission of the collided frame even after
the collision period (late collision). When reset, the MAC disables frame transmission on a late
collision. In any case, the Late Collision status is appropriately updated in the Transmit Packet status.
11
Disable Broadcast Frames (BCAST). When set, disables the reception of broadcast frames. When
reset, forwards all broadcast frames to the application.
Note:
When wake-up frame detection is enabled via the WUEN bit of the WUCSR—Wake-up
Control and Status Register, a broadcast wake-up frame will wake-up the device despite the
state of this bit.
10
Disable Retry (DISRTY). When set, the MAC attempts only one transmission. When a collision is
seen on the bus, the MAC ignores the current frame and goes to the next frame and a retry error is
reported in the Transmit status. When reset, the MAC attempts 16 transmissions before signaling a
retry error.
9
Reserved
8
Automatic Pad Stripping (PADSTR). When set, the MAC strips the pad field on all incoming frames,
if the length field is less than 46 bytes. The FCS field is also stripped, since it is computed at the
transmitting station based on the data and pad field characters, and is invalid for a received frame
that has had the pad characters stripped. Receive frames with a 46-byte or greater length field are
passed to the Application unmodified (FCS is not stripped). When reset, the MAC passes all incoming
frames to the host unmodified.
Note:
Revision 2.6 (12-04-08)
When PADSTR is enabled, the RX Checksum Offload Engine must be disabled (bit 0
(RXCOE_EN) of the COE_CR—Checksum Offload Engine Control Register) and vice versa.
These functions cannot be enabled simultaneously.
108
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
BITS
DESCRIPTION
7-6
BackOff Limit (BOLMT). The BOLMT bits allow the user to set its back-off limit in a relaxed or
aggressive mode. According to IEEE 802.3, the MAC has to wait for a random number [r] of slottimes** after it detects a collision, where:
(eq.1)0 < r < 2K
The exponent K is dependent on how many times the current frame to be transmitted has been retried,
as follows:
(eq.2)K = min (n, 10) where n is the current number of retries.
If a frame has been retried three times, then K = 3 and r= 8 slot-times maximum. If it has been retried
12 times, then K = 10, and r = 1024 slot-times maximum.
An LFSR (linear feedback shift register) 20-bit counter emulates a 20bit random number generator,
from which r is obtained. Once a collision is detected, the number of the current retry of the current
frame is used to obtain K (eq.2). This value of K translates into the number of bits to use from the
LFSR counter. If the value of K is 3, the MAC takes the value in the first three bits of the LFSR counter
and uses it to count down to zero on every slot-time. This effectively causes the MAC to wait eight
slot-times. To give the user more flexibility, the BOLMT value forces the number of bits to be used
from the LFSR counter to a predetermined value as in the table below.
BOLMT Value
# Bits Used from LFSR Counter
2’b00
10
2’b01
8
2’b10
4
2’b11
1
Thus, if the value of K = 10, the MAC will look at the BOLMT if it is 00, then use the lower ten bits of the LFSR
counter for the wait countdown. If the BOLMT is 10, then it will only use the value in the first four bits for the
wait countdown, etc.
**Slot-time = 512 bit times. (See IEEE 802.3 Spec., Secs. 4.2.3.25 and 4.4.2.1)
5
Deferral Check (DFCHK). When set, enables the deferral check in the MAC. The MAC will abort the
transmission attempt if it has deferred for more than 24,288 bit times. Deferral starts when the
transmitter is ready to transmit, but is prevented from doing so because the CRS is active. Defer time
is not cumulative. If the transmitter defers for 10,000 bit times, then transmits, collides, backs off, and
then has to defer again after completion of back-off, the deferral timer resets to 0 and restarts. When
reset, the deferral check is disabled in the MAC and the MAC defers indefinitely.
4
Reserved
3
Transmitter enable (TXEN). When set, the MAC’s transmitter is enabled and it will transmit frames
from the buffer onto the cable.
When reset, the MAC’s transmitter is disabled and will not transmit any frames.
2
Receiver Enable (RXEN). When set (1), the MAC’s receiver is enabled and will receive frames from
the internal PHY.
When reset, the MAC’s receiver is disabled and will not receive any frames from the internal PHY.
1-0
Reserved
SMSC LAN9221/LAN9221i
109
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.2
ADDRH—MAC Address High Register
Offset:
2
Attribute:
R/W
Default Value:
0000FFFFh
Size:
32 bits
The MAC Address High register contains the upper 16-bits of the physical address of the MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Controller if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0])
is loaded from address 0x05 of the EEPROM. The second byte (bits [15:8]) is loaded from address
0x06 of the EEPROM. Please refer to Section 4.6 for more information on the EEPROM. Section 5.4.3
details the byte ordering of the ADDRL and ADDRH registers with respect to the reception of the
Ethernet physical address.
BITS
DESCRIPTION
31-16
Reserved
15-0
Physical Address [47:32]. This field contains the upper 16-bits (47:32) of the Physical Address of
the LAN9221/LAN9221i device. The content of this field is undefined until loaded from the EEPROM
at power-on. The host can update the contents of this field after the initialization process has
completed.
Revision 2.6 (12-04-08)
110
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.3
ADDRL—MAC Address Low Register
Offset:
3
Attribute:
R/W
Default Value:
FFFFFFFFh
Size:
32 bits
The MAC Address Low register contains the lower 32 bits of the physical address of the MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Controller if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0])
is loaded from address 0x01 of the EEPROM. The most significant byte of this register is loaded from
address 0x04 of the EEPROM. Please refer to Section 4.6 for more information on the EEPROM.
BITS
DESCRIPTION
31-0
Physical Address [31:0]. This field contains the lower 32 bits (31:0) of the Physical Address of the
LAN9221/LAN9221i device. The content of this field is undefined until loaded from the EEPROM at
power-on. The host can update the contents of this field after the initialization process has completed.
Table 5.7 below illustrates the byte ordering of the ADDRL and ADDRH registers with respect to the
reception of the Ethernet physical address. Also shown is the correlation between the EEPROM
addresses and ADDRL and ADDRH registers.
Table 5.7 ADDRL, ADDRH and EEPROM Byte Ordering
EEPROM ADDRESS
ADDRN
ORDER OF RECEPTION ON
ETHERNET
0x01
ADDRL[7:0]
1st
0x02
ADDRL[15:8]
2nd
0x03
ADDRL[23:16]
3rd
0x04
ADDRL[31:24]
4th
0x05
ADDRH[7:0]
5th
0x06
ADDRH[15:8]
6th
As an example, if the desired Ethernet physical address is 12-34-56-78-9A-BC, the ADDRL and
ADDRH registers would be programmed as shown in Figure 5.2. The values required to automatically
load this configuration from the EEPROM are also shown.
31
24 23
xx
16 15
xx
8 7
0xBC
0
0x9A
ADDRH
31
0x78
24 23
16 15
0x56
8 7
0x34
0
0x12
0x06
0xBC
0x05
0x9A
0x04
0x78
0x03
0x56
0x02
0x34
0x01
0x12
0x00
0xA5
EEPROM
ADDRL
Figure 5.2 Example ADDRL, ADDRH and EEPROM Setup
Note: By convention, the left most byte of the Ethernet address (in this example 0x12) is the most
significant byte and is transmitted/received first.
SMSC LAN9221/LAN9221i
111
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.4
HASHH—Multicast Hash Table High Register
Offset:
4
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
The 64-bit Multicast table is used for group address filtering. For hash filtering, the contents of the
destination address in the incoming frame is used to index the contents of the Hash table. The most
significant bit determines the register to be used (Hi/Low), while the other five bits determine the bit
within the register. A value of 00000 selects Bit 0 of the Multicast Hash Table Lo register and a value
of 11111 selects the Bit 31 of the Multicast Hash Table Hi register.
If the corresponding bit is 1, then the multicast frame is accepted. Otherwise, it is rejected. If the “Pass All
Multicast” (MCPAS) bit is set (1), then all multicast frames are accepted regardless of the multicast hash
values.
The Multicast Hash Table Hi register contains the higher 32 bits of the hash table and the Multicast
Hash Table Low register contains the lower 32 bits of the hash table.
BITS
31-0
5.4.5
DESCRIPTION
Upper 32 bits of the 64-bit Hash Table
HASHL—Multicast Hash Table Low Register
Offset:
5
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register defines the lower 32-bits of the Multicast Hash Table. Please refer to Table 5.4.4,
"HASHH—Multicast Hash Table High Register" for further details.
BITS
31-0
DESCRIPTION
Lower 32 bits of the 64-bit Hash Table
Revision 2.6 (12-04-08)
112
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.6
MII_ACC—MII Access Register
Offset:
6
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register is used to control the Management cycles to the PHY.
BITS
DESCRIPTION
31-16
Reserved
15-11
PHY Address: For every access to this register, this field must be set to 00001b.
10-6
MII Register Index (MIIRINDA): These bits select the desired MII register in the PHY.
5-2
Reserved
1
MII Write (MIIWnR): Setting this bit tells the PHY that this will be a write operation using the MII data
register. If this bit is not set, this will be a read operation, packing the data in the MII data register.
0
MII Busy (MIIBZY): This bit must be polled to determine when the MII register access is complete.
This bit must read a logical 0 before writing to this register and MII data register.
The LAN driver software must set (1) this bit in order for the LAN9221/LAN9221i to read or write any
of the MII PHY registers.
During a MII register access, this bit will be set, signifying a read or write access is in progress. The
MII data register must be kept valid until the MAC clears this bit during a PHY write operation. The
MII data register is invalid until the MAC has cleared this bit during a PHY read operation.
5.4.7
MII_DATA—MII Data Register
Offset:
7
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains either the data to be written to the PHY register specified in the MII Access
Register, or the read data from the PHY register whose index is specified in the MII Access Register.
BITS
DESCRIPTION
31-16
Reserved
15-0
MII Data. This contains the 16-bit value read from the PHY read operation or the 16-bit data value to
be written to the PHY before an MII write operation.
SMSC LAN9221/LAN9221i
113
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.8
FLOW—Flow Control Register
Offset:
8
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register controls the generation and reception of the Control (Pause command) frames by the
MAC’s flow control block. The control frame fields are selected as specified in the 802.3x Specification
and the Pause-Time value from this register is used in the “Pause Time” field of the control frame. In
full-duplex mode the FCBSY bit is set until the control frame is transferred onto the cable. In halfduplex mode FCBSY is set while back pressure is being asserted. The host has to make sure that the
Busy bit is cleared before writing the register. The Pass Control Frame bit (FCPASS) does not affect
the sending of the frames, including Control Frames, to the Application Interface. The Flow Control
Enable (FCEN) bit enables the receive portion of the Flow Control block.
This register is used in conjunction with the AFC_CFG register in the Slave CSRs to configure flow
control. Software flow control is initiated using the AFC_CFG register.
Note: The LAN9221/LAN9221i will not transmit pause frames or assert back pressure if the
transmitter is disabled.
BITS
DESCRIPTION
31-16
Pause Time (FCPT). This field indicates the value to be used in the PAUSE TIME field in the control
frame. This field must be initialized before full-duplex automatic flow control is enabled.
15-3
Reserved
2
Pass Control Frames (FCPASS). When set, the MAC sets the Packet Filter bit in the Receive packet
status to indicate to the Application that a valid Pause frame has been received. The Application must
accept or discard a received frame based on the Packet Filter control bit. The MAC receives, decodes
and performs the Pause function when a valid Pause frame is received in Full-Duplex mode and when
flow control is enabled (FCE bit set). When reset, the MAC resets the Packet Filter bit in the Receive
packet status.
The MAC always passes the data of all frames it receives (including Flow Control frames) to the
Application. Frames that do not pass Address filtering, as well as frames with errors, are passed to
the Application. The Application must discard or retain the received frame’s data based on the
received frame’s STATUS field. Filtering modes (Promiscuous mode, for example) take precedence
over the FCPASS bit.
1
Flow Control Enable (FCEN). When set, enables the MAC Flow Control function. The MAC decodes
all incoming frames for control frames; if it receives a valid control frame (PAUSE command), it
disables the transmitter for a specified time (Decoded pause time x slot time). When reset, the MAC
flow control function is disabled; the MAC does not decode frames for control frames.
Note:
0
Flow Control is applicable when the MAC is set in Full Duplex Mode. In Half-Duplex mode,
this bit enables the Backpressure function to control the flow of received frames to the MAC.
Flow Control Busy (FCBSY). This bit is set high whenever a pause frame or back pressure is being
transmitted. This bit should read logical 0 before writing to the Flow Control (FLOW) register. During
a transfer of Control Frame, this bit continues to be set, signifying that a frame transmission is in
progress. After the PAUSE control frame’s transmission is complete, the MAC resets to 0.
Notes:
„ When writing this register the FCBSY bit must always be zero.
„ Applications must always write a zero to this bit
Revision 2.6 (12-04-08)
114
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.9
VLAN1—VLAN1 Tag Register
Offset:
9
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains the VLAN tag field to identify VLAN1 frames. For VLAN frames the legal frame
length is increased from 1518 bytes to 1522 bytes.
BITS
DESCRIPTION
31-16
Reserved
15-0
VLAN1 Tag Identifier (VTI1). This contains the VLAN Tag field to identify the VLAN1 frames. This
field is compared with the 13th and 14th bytes of the incoming frames for VLAN1 frame detection.
If used, this register must be set to 0x8100.
5.4.10
VLAN2—VLAN2 Tag Register
Offset:
A
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains the VLAN tag field to identify VLAN2 frames. For VLAN frames the legal frame
length is increased from 1518 bytes to 1522 bytes.
BITS
DESCRIPTION
31-16
Reserved
15-0
VLAN2 Tag Identifier (VTI2). This contains the VLAN Tag field to identify the VLAN2 frames. This
field is compared with the 13th and 14th bytes of the incoming frames for VLAN2 frame detection.If
used, this register must be set to 0x8100.
SMSC LAN9221/LAN9221i
115
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.11
WUFF—Wake-up Frame Filter
Offset:
B
Attribute:
WO
Default Value:
00000000h
Size:
32 bits
This register is used to configure the wake up frame filter.
BITS
DESCRIPTION
31-0
Wake-Up Frame Filter (WFF). Wake-Up Frame Filter (WFF). The Wake-up frame filter is configured
through this register using an indexing mechanism. After hardware reset, or soft reset, the MAC loads
the first value written to this location to the first DWORD in the Wake-up frame filter (filter 0 byte
mask). The second value written to this location is loaded to the second DWORD in the wake-up
frame filter (filter 1 byte mask) and so on. Once all eight DWORDs have been written, the internal
pointer will once again point to the first entry and the filter entries can be modified in the same manner.
Note:
5.4.12
This is a write-only register.
WUCSR—Wake-up Control and Status Register
Offset:
C
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register contains data pertaining to the MAC’s remote wake-up status and capabilities.
BITS
31-10
9
8-7
DESCRIPTION
Reserved
Global Unicast Enable (GUE). When set, the MAC wakes up from power-saving mode on receipt of
a global unicast frame. A global unicast frame has the MAC Address [0] bit set to 0.
Reserved
6
Remote Wake-Up Frame Received (WUFR). The MAC, upon receiving a valid Remote Wake-up
frame, sets this bit.
5
Magic Packet Received (MPR). The MAC, upon receiving a valid Magic Packet, sets this bit.
4-3
Reserved
2
Wake-Up Frame enabled (WUEN). When set, Remote Wake-Up mode is enabled and the MAC is
capable of detecting wake-up frames as programmed in the wake-up frame filter.
1
Magic Packet Enable (MPEN). When set, Magic Packet Wake-up mode is enabled.
0
Reserved
Revision 2.6 (12-04-08)
116
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.4.13
COE_CR—Checksum Offload Engine Control Register
Offset:
D
Attribute:
R/W
Default Value:
00000000h
Size:
32 bits
This register controls the transmit and receive checksum offload engines.
BITS
31-17
16
DESCRIPTION
Reserved
TX Checksum Offload Engine Enable (TXCOE_EN). This bit enables/disables the Transmit COE.
This bit may only be changed if the TX data path is disabled.
0: The TXCOE is bypassed
1: The TXCOE is enabled
15-2
1
Reserved
RX Checksum Offload Engine Mode (RXCOE_MODE) This register indicates whether the RXCOE
will check for VLAN tags or a SNAP header prior to beginning its checksum calculation. In its default
mode, the calculation will always begin 14 bytes into the frame.
The RXCOE_MODE may only be changed if the ESS RX path is disabled.
0: Begin checksum calculation after first 14 bytes of Ethernet Frame
1: Begin checksum calculation at start of L3 packet by adjusting for VLAN tags and/or SNAP header.
0
RX Checksum Offload Engine Enable (RXCOE_EN). This bit enables/disables the Receive COE.
This bit may only be changed if the RX data path is disabled.
0: The RXCOE is bypassed
1: The RXCOE is enabled
Note:
SMSC LAN9221/LAN9221i
When the RXCOE is enabled, automatic pad stripping must be disabled (bit 8 (PADSTR) of
the MAC_CR—MAC Control Register) and vice versa. These functions cannot be enabled
simultaneously.
117
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5
PHY Registers
The PHY registers are not memory mapped. These registers are accessed indirectly through the MAC
via the MII_ACC and MII_DATA registers. An index must be used to access individual PHY registers.
PHY Register Indexes are shown in Table 5.8, "LAN9221/LAN9221i PHY Control and Status Register".
Note: The NASR (Not Affected by Software Reset) designation is only applicable when bit 15 of
the PHY Basic Control Register (Reset) is set.
Table 5.8 LAN9221/LAN9221i PHY Control and Status Register
PHY CONTROL AND STATUS REGISTERS
INDEX
(IN DECIMAL)
REGISTER NAME
0
Basic Control Register
1
Basic Status Register
2
PHY Identifier 1
3
PHY Identifier 2
4
Auto-Negotiation Advertisement Register
5
Auto-Negotiation Link Partner Ability Register
6
Auto-Negotiation Expansion Register
17
Mode Control/Status Register
18
Special Modes Register
27
Special Control/Status Indications
29
Interrupt Source Register
30
Interrupt Mask Register
31
PHY Special Control/Status Register
Revision 2.6 (12-04-08)
118
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.1
Basic Control Register
Index (In Decimal):
0
Size:
16-bits
BITS
DESCRIPTION
TYPE
DEFAULT
15
Reset. 1 = software reset. Bit is self-clearing. For best results, when setting
this bit do not set other bits in this register.
RW/SC
0
14
Loopback. 1 = loopback mode, 0 = normal operation
RW
0
13
Speed Select. 1 = 100Mbps, 0 = 10Mbps. Ignored if Auto Negotiation is
enabled (0.12 = 1).
RW
See Note 5.1
12
Auto-Negotiation Enable. 1 = enable auto-negotiate process (overrides
0.13 and 0.8) 0 = disable auto-negotiate process.
RW
1
11
Power Down. 1 = General power down-mode, 0 = normal operation.
RW
0
RO
0
RW/SC
0
Note:
After this bit is cleared, the PHY may auto-negotiate with it's
partner station. This process may take a few seconds to complete.
Once auto-negotiation is complete, bit 5 of the PHY's Basic Status
Register will be set.
10
Reserved
9
Restart Auto-Negotiate. 1 = restart auto-negotiate process 0 = normal
operation. Bit is self-clearing.
8
Duplex Mode. 1 = full duplex, 0 = half duplex. Ignored if Auto Negotiation
is enabled (0.12 = 1).
RW
See Note 5.1
7
Collision Test. 1 = enable COL test, 0 = disable COL test
RW
0
Reserved
RO
0
6-0
Note 5.1
SMSC LAN9221/LAN9221i
The default value of this bit is determined by the auto-negotiation process.
119
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.2
Basic Status Register
Index (In Decimal):
BITS
1
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15
100Base-T4. 1 = T4 able, 0 = no T4 ability
RO
0
14
100Base-TX Full Duplex. 1 = TX with full duplex, 0 = no TX full duplex
ability.
RO
1
13
100Base-TX Half Duplex. 1 = TX with half duplex, 0 = no TX half duplex
ability.
RO
1
12
10Base-T Full Duplex. 1 = 10Mbps with full duplex 0 = no 10Mbps with full
duplex ability
RO
1
11
10Base-T Half Duplex. 1 = 10Mbps with half duplex 0 = no 10Mbps with
half duplex ability
RO
1
Reserved
RO
0
5
Auto-Negotiate Complete. 1 = auto-negotiate process completed 0 = autonegotiate process not completed
RO
0
4
Remote Fault. 1 = remote fault condition detected 0 = no remote fault
RO/LH
0
3
Auto-Negotiate Ability. 1 = able to perform auto-negotiation function 0 =
unable to perform auto-negotiation function
RO
1
2
Link Status. 1 = link is up, 0 = link is down
RO/LL
0
1
Jabber Detect. 1 = jabber condition detected 0 = no jabber condition
detected
RO/LH
0
0
Extended Capabilities. 1 = supports extended capabilities registers 0 =
does not support extended capabilities registers.
RO
1
TYPE
DEFAULT
RO
0x0007h
10-6
5.5.3
PHY Identifier 1
Index (In Decimal):
BITS
15-0
2
Size:
DESCRIPTION
PHY ID Number. Assigned to the 3rd through 18th bits of the
Organizationally Unique Identifier (OUI), respectively.
Revision 2.6 (12-04-08)
120
DATASHEET
16-bits
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.4
PHY Identifier 2
Index (In Decimal):
BITS
3
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
0xC0C3h
15-10
PHY ID Number b. Assigned to the 19th through 24th bits of the OUI.
RO
9-4
Model Number. Six-bit manufacturer’s model number.
RO
3-0
Revision Number. Four-bit manufacturer’s revision number.
RO
5.5.5
Auto-negotiation Advertisement
Index (In Decimal):
BITS
4
Size:
16-bits
TYPE
DEFAULT
Reserved
RO
00
13
Remote Fault. 1 = remote fault detected, 0 = no remote fault
R/W
0
12
Reserved
R/W
0
Pause Operation. (See Note 5.2)
00 No PAUSE
01 Symmetric PAUSE
10 Asymmetric PAUSE
11 Advertise support for both Symmetric PAUSE and Asymmetric PAUSE
R/W
00
9
Reserved
RO
0
8
100Base-TX Full Duplex. 1 = TX with full duplex, 0 = no TX full duplex
ability
R/W
1
7
100Base-TX. 1 = TX able, 0 = no TX ability
R/W
1
6
10Base-T Full Duplex.
1 = 10Mbps with full duplex
0 = no 10Mbps with full duplex ability
R/W
1
5
10Base-T. 1 = 10Mbps able, 0 = no 10Mbps ability
R/W
1
Selector Field. [00001] = IEEE 802.3
R/W
00001
15:14
11:10
4:0
DESCRIPTION
Note 5.2
SMSC LAN9221/LAN9221i
When both symmetric PAUSE and asymmetric PAUSE support are advertised (value of
11), the device will only be configured to, at most, one of the two settings upon autonegotiation completion.
121
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.6
Auto-negotiation Link Partner Ability
Index (In Decimal):
BITS
5
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15
Next Page. 1 = next page capable, 0 = no next page ability. This device
does not support next page ability.
RO
0
14
Acknowledge. 1 = link code word received from partner 0 = link code word
not yet received
RO
0
Note:
This bit will always read 0
13
Remote Fault. 1 = remote fault detected, 0 = no remote fault
RO
0
12
Reserved
RO
0
Pause Operation.
00 No PAUSE supported by partner station
01 Symmetric PAUSE supported by partner station
10 Asymmetric PAUSE supported by partner station
11 Both Symmetric PAUSE and Asymmetric PAUSE supported by partner
station
RO
00
9
100Base-T4. 1 = T4 able, 0 = no T4 ability
RO
0
8
100Base-TX Full Duplex. 1 = TX with full duplex, 0 = no TX full duplex
ability
RO
0
7
100Base-TX. 1 = TX able, 0 = no TX ability
RO
0
6
10Base-T Full Duplex.
1 = 10Mbps with full duplex
0 = no 10Mbps with full duplex ability
RO
0
5
10Base-T. 1 = 10Mbps able, 0 = no 10Mbps ability
RO
0
Selector Field. [00001] = IEEE 802.3
RO
00001
11-10
4:0
Revision 2.6 (12-04-08)
122
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.7
Auto-negotiation Expansion
Index (In Decimal):
BITS
15:5
6
Size:
16-bits
DESCRIPTION
Reserved
TYPE
DEFAULT
RO
0
4
Parallel Detection Fault.
1 = fault detected by parallel detection logic
0 = no fault detected by parallel detection logic
RO/LH
0
3
Link Partner Next Page Able.
1 = link partner has next page ability
0 = link partner does not have next page ability
RO
0
2
Next Page Able.
1 = local device has next page ability
0 = local device does not have next page ability
RO
0
1
Page Received.
1 = new page received
0 = new page not yet received
RO/LH
0
0
Link Partner Auto-Negotiation Able.
1 = link partner has auto-negotiation ability
0 = link partner does not have auto-negotiation ability
RO
0
TYPE
DEFAULT
Reserved. Write as 0; ignore on read.
RW
0
EDPWRDOWN. Enable the Energy Detect Power-Down mode:
0=Energy Detect Power-Down is disabled
1=Energy Detect Power-Down is enabled
RW
0
Reserved. Write as 0, ignore on read
RW
0
1
ENERGYON. Indicates whether energy is detected. This bit goes to a “0” if
no valid energy is detected within 256ms. Reset to “1” by hardware reset,
unaffected by SW reset.
RO
See Note 5.3
0
Reserved. Write as “0”. Ignore on read.
RW
0
5.5.8
Mode Control/Status
Index (In Decimal):
BITS
15-14
13
12-2
17
Size:
16-bits
DESCRIPTION
Note 5.3
SMSC LAN9221/LAN9221i
The default value of this bit will vary dependant on the current link state of the line.
123
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.9
Special Modes
Index (In Decimal):
ADDRESS
18
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15-8
Reserved
RW,
NASR
7:5
MODE: PHY Mode of operation. Refer to Table 5.9 for more details.
RW,
NASR
111
4:0
PHYAD: PHY Address:
The PHY Address is used for the SMI address.
RW,
NASR
00001b
Table 5.9 MODE Control
DEFAULT REGISTER BIT VALUES
MODE
MODE DEFINITIONS
REGISTER 0
REGISTER 4
[13,12,10,8]
[8,7,6,5]
000
10Base-T Half Duplex. Auto-negotiation disabled.
0000
N/A
001
10Base-T Full Duplex. Auto-negotiation disabled.
0001
N/A
010
100Base-TX Half Duplex. Auto-negotiation disabled.
CRS is active during Transmit & Receive.
1000
N/A
011
100Base-TX Full Duplex. Auto-negotiation disabled.
CRS is active during Receive.
1001
N/A
100
100ase-TX Half Duplex is advertised. Autonegotiation enabled.
CRS is active during Transmit & Receive.
1100
0100
101
Repeater mode. Auto-negotiation enabled.
100Base-TX Half Duplex is advertised.
CRS is active during Receive.
1100
0100
110
Reserved - Do not set the LAN9221/LAN9221i in
this mode.
N/A
N/A
111
All capable. Auto-negotiation enabled.
X10X
Note 5.4
1111
Note 5.4
Revision 2.6 (12-04-08)
When MODE=111, the register 0 bits 13 and 8 are variable dependant on the autonegotiated speed and duplex.
124
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.10
Special Control/Status Indications
Index (In Decimal):
ADDRESS
27
Size:
16-bits
DESCRIPTION
MODE
DEFAULT
15
Override AMDIX Strap
0 - AMDIX_EN (pin 52) enables or disables HP Auto MDIX
1 - Override pin 52. PHY Register 27.14 and 27.13 determine MDIX
function
RW
0
14
Auto-MDIX Enable: Only effective when 27.15=1, otherwise ignored.
0 = Disable Auto-MDIX. 27.13 determines normal or reversed connection.
1 = Enable Auto-MDIX. 27.13 must be set to 0.
RW
0
13
Auto-MDIX State. Only effective when 27.15=1, otherwise ignored.
When 27.14 = 0 (manually set MDIX state):
0 = no crossover (TPO = output, TPI = input)
1 = crossover (TPO = input, TPI = output)
When 27.14 = 1 (automatic MDIX) this bit must be set to 0.
Do not use the combination 27.15=1, 27.14=1, 27.13=1.
RW
0
Reserved: Write as 0. Ignore on read.
RW
0
RW,
NASR
0
12:11
10
VCOOFF_LP: Forces the Receive PLL 10M to lock on the reference clock
at all times:
0 - Receive PLL 10M can lock on reference or line as needed (normal
operation)
1 - Receive PLL 10M is locked on the reference clock.
In this mode 10M data packets cannot be received.
9-5
Reserved: Write as 0. Ignore on read.
RW
0
4
XPOL: Polarity state of the 10Base-T:
0 - Normal polarity
1 - Reversed polarity
RO
0
Reserved: Read only - Writing to these bits have no effect.
RO
XXXXb
3:0
SMSC LAN9221/LAN9221i
125
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.11
Interrupt Source Flag
Index (In Decimal):
BITS
29
Size:
16-bits
TYPE
DEFAULT
Reserved. Ignore on read.
RO/LH
0
7
INT7. 1= ENERGYON generated, 0= not source of interrupt
RO/LH
0
6
INT6. 1= Auto-Negotiation complete, 0= not source of interrupt
RO/LH
0
5
INT5. 1= Remote Fault Detected, 0= not source of interrupt
RO/LH
0
4
INT4. 1= Link Down (link status negated), 0= not source of interrupt
RO/LH
See Note 5.5
3
INT3. 1= Auto-Negotiation LP Acknowledge, 0= not source of interrupt
RO/LH
0
2
INT2. 1= Parallel Detection Fault, 0= not source of interrupt
RO/LH
0
1
INT1. 1= Auto-Negotiation Page Received, 0= not source of interrupt
RO/LH
0
0
Reserved.
RO/LH
0
15-8
DESCRIPTION
Note 5.5
5.5.12
The default value of this bit will vary dependant on the current link state of the line.
Interrupt Mask
Index (In Decimal):
BITS
30
Size:
16-bits
DESCRIPTION
TYPE
DEFAULT
15-8
Reserved. Write as 0; ignore on read.
RO
0
7-0
Mask Bits. 1 = interrupt source is enabled 0 = interrupt source is masked
RW
0
Revision 2.6 (12-04-08)
126
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
5.5.13
PHY Special Control/Status
Index (In Decimal):
BITS
31
Size:
TYPE
DEFAULT
Reserved
RO
000b
Autodone. Auto-negotiation done indication:
0 = Auto-negotiation is not done or disabled (or not active)
1 = Auto-negotiation is done
RO
0b
11-5
Reserved. Write as 0000010b, ignore on Read.
RW
0000010b
4-2
Speed Indication. HCDSPEED value:
[001]=10Mbps half-duplex
[101]=10Mbps full-duplex
[010]=100Base-TX half-duplex
[110]=100Base-TX full-duplex
RO
See Note 5.6
1-0
Reserved. Write as 0; ignore on Read
RO
00b
15 - 13
12
DESCRIPTION
16-bits
Note 5.6
SMSC LAN9221/LAN9221i
The default value of this bit is determined by the auto-negotiation process.
127
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 6 Timing Diagrams
6.1
Equivalent Test Load
Output timing specifications assume an equivalent test load as illustrated in Figure 6.1 below.
OUTPUT
Test load varies dependent on VDDVARIO:
VDDVARIO = 3.3V ± 300mV: 25pF
VDDVARIO = 2.5V ± 10%: 10pF
VDDVARIO=1.8V ± 10%: 10pF
Figure 6.1 Equivalent Test Load
6.2
Host Interface Timing
The LAN9221/LAN9221i supports the following host cycles:
Read Cycles:
„
PIO Reads (nCS or nRD controlled)
„
PIO Burst Reads (nCS or nRD controlled)
„
RX Data FIFO Direct PIO Reads (nCS or nRD controlled)
„
RX Data FIFO Direct PIO Burst Reads (nCS or nRD controlled)
Write Cycles:
„
PIO writes (nCS and nWR controlled)
„
TX Data FIFO direct PIO writes (nCS or nWR controlled)
All timing measurements were verified under the following conditions:
Note: The specified test load used for output timing is dependant on VDDVARIO.
Temperature: ................................................................................................................................ Note 6.1
Load Capacitance (VDDVARIO = 3.3V +/- 300mV):........................................................................ 25pF
Load Capacitance (VDDVARIO = 2.5V +/- 10%): ............................................................................ 10pF
Load Capacitance (VDDVARIO = 1.8V +/- 10%): ............................................................................ 10pF
Note 6.1
Revision 2.6 (12-04-08)
0oC to +70oC for commercial version, -40oC to +85oC for industrial version.
128
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.2.1
Special Restrictions on Back-to-Back Write/Read Cycles
It is important to note that there are specific restrictions on the timing of back-to-back write-read
operations. These restrictions concern reading the control registers after any write cycle to the
LAN9221/LAN9221i device. In many cases there is a required minimum delay between writing to the
LAN9221/LAN9221i, and the subsequent side effect (change in the control register value). For
example, when writing to the TX Data FIFO, it takes up to 135ns for the level indication to change in
the TX_FIFO_INF register.
In order to prevent the host from reading stale data after a write operation, minimum wait periods must
be enforced. These periods are specified in Table 6.1, "Read After Write Timing Rules". The host
processor is required to wait the specified period of time after any write to the LAN9221/LAN9221i
before reading the resource specified in the table. These wait periods are for read operations that
immediately follow any write cycle. Note that the required wait period is dependant upon the register
being read after the write.
Performing "dummy" reads of the BYTE_TEST register is a convenient way to guarantee that the
minimum write-to-read timing restriction is met. Table 6.1 also shows the number of dummy reads that
are required before reading the register indicated. The number of BYTE_TEST reads in this table is
based on the minimum timing for Tcycle (45ns). For microprocessors with slower busses the number
of reads may be reduced as long as the total time is equal to, or greater than the time specified in the
table. Note that dummy reads of the BYTE_TEST register are not required as long as the minimum
time period is met.
Table 6.1 Read After Write Timing Rules
REGISTER NAME
MINIMUM WAIT TIME FOR READ
FOLLOWING ANY WRITE CYCLE
(IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYCLE OF 45NS)
ID_REV
0
0
IRQ_CFG
135
3
INT_STS
90
2
INT_EN
45
1
BYTE_TEST
0
0
FIFO_INT
45
1
RX_CFG
45
1
TX_CFG
45
1
HW_CFG
45
1
RX_DP_CTRL
45
1
RX_FIFO_INF
0
0
TX_FIFO_INF
135
3
PMT_CTRL
315
7
GPIO_CFG
45
1
GPT_CFG
45
1
GPT_CNT
135
3
WORD_SWAP
45
1
FREE_RUN
180
4
SMSC LAN9221/LAN9221i
129
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 6.1 Read After Write Timing Rules (continued)
6.2.2
REGISTER NAME
MINIMUM WAIT TIME FOR READ
FOLLOWING ANY WRITE CYCLE
(IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYCLE OF 45NS)
RX_DROP
0
0
MAC_CSR_CMD
45
1
MAC_CSR_DATA
45
1
AFC_CFG
45
1
E2P_CMD
45
1
E2P_DATA
45
1
Special Restrictions on Back-to-Back Read Cycles
There are also restrictions on specific back-to-back read operations. These restrictions concern
reading specific registers after reading resources that have side effects. In many cases there is a delay
between reading the LAN9221/LAN9221i, and the subsequent indication of the expected change in the
control register values.
In order to prevent the host from reading stale data on back-to-back reads, minimum wait periods have
been established. These periods are specified in Table 6.2, "Read After Read Timing Rules". The host
processor is required to wait the specified period of time between read operations of specific
combinations of resources. The wait period is dependant upon the combination of registers being read.
Performing "dummy" reads of the BYTE_TEST register is a convenient way to guarantee that the
minimum wait time restriction is met. Table 6.2 also shows the number of dummy reads that are
required for back-to-back read operations. The number of BYTE_TEST reads in this table is based on
the minimum timing for Tcycle (45ns). For microprocessors with slower busses the number of reads
may be reduced as long as the total time is equal to, or greater than the time specified in the table.
Dummy reads of the BYTE_TEST register are not required as long as the minimum time period is met.
Table 6.2 Read After Read Timing Rules
AFTER
READING...
WAIT FOR THIS MANY
NS…
OR PERFORM THIS MANY
READS OF BYTE_TEST…
(ASSUMING Tcycle OF 45NS)
BEFORE READING...
RX Data FIFO
135
3
RX_FIFO_INF
RX Status FIFO
135
3
RX_FIFO_INF
TX Status FIFO
135
3
TX_FIFO_INF
RX_DROP
180
4
RX_DROP
Revision 2.6 (12-04-08)
130
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.3
PIO Reads
PIO reads can be used to access CSRs or RX Data and RX/TX status FIFOs. In this mode, counters
in the CSRs are latched at the beginning of the read cycle. Read data is valid as indicated in the timing
diagram. PIO reads can be performed using Chip Select (nCS) or Read Enable (nRD). Either or both
of these control signals must go high between cycles for the period specified.
Note: Some registers have restrictions on the timing of back-to-back, write-read and read-read
cycles.
A[7:1]
nCS, nRD
Data Bus
Figure 6.2 PIO Read Cycle Timing
Note: The “Data Bus” width is 16 bits
Table 6.3 PIO Read Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
Read Cycle Time
45
ns
tcsl
nCS, nRD Assertion Time
32
ns
tcsh
nCS, nRD Deassertion Time
13
ns
tcsdv
nCS, nRD Valid to Data Valid
tasu
Address Setup to nCS, nRD Valid
0
ns
tah
Address Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
tcycle
Note 6.2
30
Note 6.2
0
ns
ns
ns
When VDDVARIO is 3.3V or 2.5V, the maximum Tdoff time is 7ns. When VDDVARIO is
1.8V, the maximum Tdoff time is 9ns.
Note: A PIO Read cycle begins when both nCS and nRD are asserted. The cycle ends when either
or both nCS and nRD are deasserted. They may be asserted and deasserted in any order.
SMSC LAN9221/LAN9221i
131
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.4
PIO Burst Reads
In this mode, performance is improved by allowing up to 16 WORD read cycles back-to-back. PIO
Burst Reads can be performed using Chip Select (nCS) or Read Enable (nRD). Either or both of these
control signals must go high between bursts for the period specified.
A[7:5]
A[4:1]
nCS, nRD
Data Bus
Figure 6.3 PIO Burst Read Cycle Timing
Note: The “Data Bus” width is 16 bits
Table 6.4 PIO Burst Read Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tcsh
nCS, nRD Deassertion Time
tcsdv
nCS, nRD Valid to Data Valid
tacyc
Address Cycle Time
45
tasu
Address Setup to nCS, nRD valid
0
tadv
Address Stable to Data Valid
tah
Address Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
Note 6.3
13
ns
30
ns
ns
40
Note 6.3
0
ns
ns
When VDDVARIO is 3.3V or 2.5V, the maximum Tdoff time is 7ns. When VDDVARIO is
1.8V, the maximum Tdoff time is 9ns.
Note: A PIO Burst Read cycle begins when both nCS and nRD are asserted. The cycle ends when
either or both nCS and nRD are deasserted. They may be asserted and deasserted in any
order.
Revision 2.6 (12-04-08)
132
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.5
RX Data FIFO Direct PIO Reads
In this mode the upper address inputs are not decoded, and any read of the LAN9221/LAN9221i will
read the RX Data FIFO. This mode is enabled when FIFO_SEL is driven high during a read access.
This is normally accomplished by connecting the FIFO_SEL signal to high-order address line. This
mode is useful when the host processor must increment its address when accessing the
LAN9221/LAN9221i. Timing is identical to a PIO read, and the FIFO_SEL signal has the same timing
characteristics as the address lines.
Note that address lines A[2:1] are still used, and address bits A[7:3] are ignored.
FIFO_SEL
A[2:1]
nCS, nRD
Data Bus
Figure 6.4 RX Data FIFO Direct PIO Read Cycle Timing
Note: The “Data Bus” width is 16 bits.
Table 6.5 RX Data FIFO Direct PIO Read Timing
SYMBOL
tcycle
DESCRIPTION
MIN
TYP
MAX
UNITS
Read Cycle Time
45
ns
tcsl
nCS, nRD Assertion Time
32
ns
tcsh
nCS, nRD Deassertion Time
13
ns
tcsdv
nCS, nRD Valid to Data Valid
tasu
Address, FIFO_SEL Setup to nCS, nRD Valid
0
ns
tah
Address, FIFO_SEL Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
Note 6.4
30
Note 6.4
0
ns
ns
ns
When VDDVARIO is 3.3V or 2.5V, the maximum Tdoff time is 7ns. When VDDVARIO is
1.8V, the maximum Tdoff time is 9ns.
Note: An RX Data FIFO Direct PIO Read cycle begins when both nCS and nRD are asserted. The
cycle ends when either or both nCS and nRD are de-asserted. They may be asserted and deasserted in any order.
SMSC LAN9221/LAN9221i
133
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.6
RX Data FIFO Direct PIO Burst Reads
In this mode the upper address inputs are not decoded, and any burst read of the LAN9221/LAN9221i
will read the RX Data FIFO. This mode is enabled when FIFO_SEL is driven high during a read
access. This is normally accomplished by connecting the FIFO_SEL signal to a high-order address
line. This mode is useful when the host processor must increment its address when accessing the
LAN9221/LAN9221i. Timing is identical to a PIO Burst Read, and the FIFO_SEL signal has the same
timing characteristics as the address lines.
In this mode, performance is improved by allowing an unlimited number of back-to-back read cycles.
RX Data FIFO Direct PIO Burst Reads can be performed using Chip Select (nCS) or Read Enable
(nRD). When either or both of these control signals go high, they must remain high for the period
specified.
Note that address lines A[2:1] are still used, and address bits A[7:3] are ignored.
FIFO_SEL
A[2:1]
nCS, nRD
Data Bus
Figure 6.5 RX Data FIFO Direct PIO Burst Read Cycle Timing
Note: The “Data Bus” width is 16 bits.
Table 6.6 RX Data FIFO Direct PIO Burst Read Cycle Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
tcsh
nCS, nRD Deassertion Time
tcsdv
nCS, nRD Valid to Data Valid
tacyc
Address Cycle Time
45
tasu
Address, FIFO_SEL Setup to nCS, nRD Valid
0
tadv
Address Stable to Data Valid
tah
Address, FIFO_SEL Hold Time
0
ns
tdon
Data Buffer Turn On Time
0
ns
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
Note 6.5
13
UNITS
ns
30
ns
ns
40
Note 6.5
0
ns
ns
When VDDVARIO is 3.3V or 2.5V, the maximum Tdoff time is 7ns. When VDDVARIO is
1.8V, the maximum Tdoff time is 9ns.
Note: An RX Data FIFO Direct PIO Burst Read cycle begins when both nCS and nRD are asserted.
The cycle ends when either or both nCS and nRD are deasserted. They may be asserted and
deasserted in any order.
Revision 2.6 (12-04-08)
134
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.7
PIO Writes
PIO writes are used for all LAN9221/LAN9221i write cycles. PIO writes can be performed using Chip
Select (nCS) or Write Enable (nWR). Either or both of these control signals must go high between
cycles for the period specified.
A[7:1]
nCS, nWR
Data Bus
Figure 6.6 PIO Write Cycle Timing
Note: The “Data Bus” width is 16 bits.
Table 6.7 PIO Write Cycle Timing
SYMBOL
tcycle
DESCRIPTION
MIN
Write Cycle Time
TYP
MAX
UNITS
45
ns
tcsl
nCS, nWR Assertion Time
32
ns
tcsh
nCS, nWR Deassertion Time
13
ns
tasu
Address Setup to nCS, nWR Assertion
0
ns
tah
Address Hold Time
0
ns
tdsu
Data Setup to nCS, nWR Deassertion
7
ns
tdh
Data Hold Time
0
ns
Note: A PIO Write cycle begins when both nCS and nWR are asserted. The cycle ends when either
or both nCS and nWR are deasserted. They may be asserted and deasserted in any order.
SMSC LAN9221/LAN9221i
135
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.8
TX Data FIFO Direct PIO Writes
In this mode the upper address inputs are not decoded, and any write to the LAN9221/LAN9221i will
write the TX Data FIFO. This mode is enabled when FIFO_SEL is driven high during a write access.
This is normally accomplished by connecting the FIFO_SEL signal to a high-order address line. This
mode is useful when the host processor must increment its address when accessing the
LAN9221/LAN9221i. Timing is identical to a PIO write, and the FIFO_SEL signal has the same timing
characteristics as the address lines.
FIFO_SEL
A[2:1]
nCS, nWR
Data Bus
Figure 6.7 TX Data FIFO Direct PIO Write Timing
Note: The “Data Bus” width is 16 bits.
Table 6.8 TX Data FIFO Direct PIO Write Timing
SYMBOL
tcycle
DESCRIPTION
MIN
TYP
MAX
UNITS
Write Cycle Time
45
ns
tcsl
nCS, nWR Assertion Time
32
ns
tcsh
nCS, nWR Deassertion Time
13
ns
tasu
Address, FIFO_SEL Setup to nCS, nWR Assertion
0
ns
tah
Address, FIFO_SEL Hold Time
0
ns
tdsu
Data Setup to nCS, nWR Deassertion
7
ns
tdh
Data Hold Time
0
ns
Note: A TX Data FIFO Direct PIO Write cycle begins when both nCS and nWR are asserted. The
cycle ends when either or both nCS and nWR are deasserted. They may be asserted and
deasserted in any order.
Revision 2.6 (12-04-08)
136
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.9
Reset Timing
T6.1
nRESET
T6.2
T6.3
Configuration
signals
T6.4
Output drive
Table 6.9 Reset Timing
PARAMETER
DESCRIPTION
MIN
TYP
MAX
UNITS
T6.1
Reset Pulse Width
30
ms
T6.2
Configuration input setup to
nRESET rising
200
ns
T6.3
Configuration input hold after
nRESET rising
10
ns
T6.4
Output Drive after nRESET
rising
SMSC LAN9221/LAN9221i
16
137
DATASHEET
NOTES
ns
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
6.10
EEPROM Timing
The following specifies the EEPROM timing requirements for the LAN9221/LAN9221i:
Figure 6.8 EEPROM Timing
Table 6.10 EEPROM Timing Values
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tCKCYC
EECLK Cycle time
1110
1130
ns
tCKH
EECLK High time
550
570
ns
tCKL
EECLK Low time
550
570
ns
tCSHCKH
EECS high before rising edge of EECLK
1070
ns
tCKLCSL
EECLK falling edge to EECS low
30
ns
tDVCKH
EEDIO valid before rising edge of EECLK
(OUTPUT)
550
ns
tCKHDIS
EEDIO disable after rising edge EECLK
(OUTPUT)
550
ns
tDSCKH
EEDIO setup to rising edge of EECLK (INPUT)
90
ns
tDHCKH
EEDIO hold after rising edge of EECLK
(INPUT)
0
ns
tCKLDIS
EECLK low to data disable (OUTPUT)
580
ns
tCSHDV
EEDIO valid after EECS high (VERIFY)
tDHCSL
EEDIO hold after EECS low (VERIFY)
tCSL
EECS low
Revision 2.6 (12-04-08)
138
DATASHEET
600
ns
0
ns
1070
ns
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 7 Operational Characteristics
7.1
Absolute Maximum Ratings*
Supply Voltage (VDDVARIO, VDD33REG, VDD33A) (Note 7.1) . . . . . . . . . . . . . . . . . . . . . 0V to +3.6V
Positive voltage on signal pins, with respect to ground (Note 7.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
Negative voltage on signal pins, with respect to ground (Note 7.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
Positive voltage on XTAL1/CLKIN, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XTAL2, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 7.4
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65oC to +150oC
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 7.1
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
Note 7.2
This rating does not apply to the following pins: XTAL1/CLKIN, XTAL2, EXRES.
Note 7.3
This rating does not apply to the following pins: EXRES.
Note 7.4
0oC to +70oC for commercial version, -40oC to +85oC for industrial version.
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 7.2, "Operating Conditions**", Section 7.6, "DC Electrical Specifications", or any other
applicable section of this specification is not implied.
7.2
Operating Conditions**
Supply Voltage (VDDVARIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1.62V to +3.6V
Supply Voltage (VDD33REG, VDD33A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V+/-300mV
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 7.4
**Proper operation of the LAN9221/LAN9221i is guaranteed only within the ranges specified in this
section.
SMSC LAN9221/LAN9221i
139
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
7.3
Power Consumption (Device Only)
This section provides typical power consumption values for the LAN9221/LAN9221i in various modes
of operation. These measurements were taken under the following conditions:
Temperature: ................................................................................................................................... +25°C
Device VDD (VDDVARIO, VDD33REG, VDD33A): ....................................................................... +3.30V
Note: Power dissipation is determined by operating frequency, temperature, and supply voltage, as
well as external source/sink requirements.
Table 7.1 Power Consumption Device Only
Total Power - Typical (mW)
MODE
10BASE-T Operation
D0, 10BASE-T /w traffic
249
D0, Idle
243
D1, Idle
146
D2, Energy Detect Power Down
64
D2, General Power Down
11
100BASE-TX Operation
D0, 100BASE-TX /w traffic
380
D0, Idle
370
D1, Idle
272
D2, Energy Detect Power Down (Cable disconnected)
64
D2, General Power Down
11
Note 7.5
Revision 2.6 (12-04-08)
D0 = Normal Operation, D1 = WOL (Wake On LAN mode), D2= Low Power Energy Detect.
140
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
7.4
Power Consumption (Device and System Components)
This section provides typical power consumption values for a complete Ethernet interface based on
the LAN9221/LAN9221i, including the power dissipated by the magnetics and other passive
components.
Note: The power measurements list below were taken under the following conditions:
Temperature: ................................................................................................................................... +25°C
Device VDD (VDDVARIO, VDD33REG, VDD33A): ....................................................................... +3.30V
Note: Power dissipation is determined by operating frequency, temperature, and supply voltage, as
well as external source/sink requirements.
Table 7.2 Power Consumption Device and System Components
Total Power - Typical (mW)
MODE
10BASE-T Operation
D0, 10BASE-T /w traffic
596
D0, Idle
591
D1, Idle
492
D2, Energy Detect Power Down
64
D2, General Power Down
11
100BASE-TX Operation
D0, 100BASE-TX /w traffic
522
D0, Idle
510
D1, Idle
416
D2, Energy Detect Power Down
64
D2, General Power Down
11
SMSC LAN9221/LAN9221i
141
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
7.5
Worst Case Current Consumption
This section details the worst case current consumption for each device power supply. These values
are provided to assist system designers with proper power supply design. These values cannot be
used to determine typical power consumption of the device. The maximum supply current for each
power supply is provided for the maximum VDDVARIO voltage in all supported ranges as detailed in
Table 7.3, Table 7.4, and Table 7.5.
Note: The current measurements listed below were taken under the following conditions:
Temperature: ................................................................................................................................ Note 7.6
Device VDD (VDDVARIO, VDD33REG, VDD33A): .................................................................... Note 7.7
Note: Current consumption is determined by operating frequency, temperature, and supply voltage,
as well as external source/sink requirements.
Note 7.6
0oC to +70oC for commercial version, -40oC to +85oC for industrial version.
Note 7.7
The device VDD voltage levels are indicated in the supply current tables below.
Table 7.3 Maximum Supply Current Characteristics VDDVARIO=3.3V + 300mV
PARAMETER
SUPPLY NAME
SUPPLY VOLTAGE
MAX CURRENT
UNITS
Variable Voltage Supply Current
VDDVARIO
3.6V
12
mA
+3.3V Regulator Supply Current
VDD33REG
3.6V
85
mA
VDD33A
3.6V
48
mA
+3.3V Analog Supply Current
Table 7.4 Maximum Supply Current Characteristics VDDVARIO=2.5V + 10%
PARAMETER
SUPPLY NAME
SUPPLY VOLTAGE
MAX CURRENT
UNITS
Variable Voltage Supply Current
VDDVARIO
2.75V
9
mA
+3.3V Regulator Supply Current
VDD33REG
3.6V
85
mA
VDD33A
3.6V
48
mA
+3.3V Analog Supply Current
Table 7.5 Maximum Supply Current Characteristics VDDVARIO=1.8V + 10%
PARAMETER
SUPPLY NAME
SUPPLY VOLTAGE
MAX CURRENT
UNITS
Variable Voltage Supply Current
VDDVARIO
1.98V
7
mA
+3.3V Regulator Supply Current
VDD33REG
3.6V
85
mA
VDD33A
3.6V
48
mA
+3.3V Analog Supply Current
Note: Above values do not include the supply current for the magnetics. Based on the recommended
implementation, the maximum supply current needed for the magnetics is 108mA.
Revision 2.6 (12-04-08)
142
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
7.6
DC Electrical Specifications
This section details the DC electrical specifications of the LAN9221/LAN9221i I/O buffers. The
electrical specifications in this section are valid over the indicated voltage range and the temperature
range specified in Section 7.2, "Operating Conditions**".
Note: When operating at reduced VDDVARIO voltage levels (less than 3.0V), do not rely on internal
pull-up and pull-down resistors to determine signal state. Refer to the individual signal
descriptions in Chapter 2, Pin Description and Configuration for more information.
Table 7.6 I/O Buffer Characteristics VDDVARIO=3.3V +/- 300mV
PARAMETER
SYMBOL
MIN
Low Input Level
VILI
-0.3
High Input Level
VIHI
Negative-Going Threshold
VILT
1.01
Positive-Going Threshold
VIHT
Schmitt Trigger Hysteresis
(VIHT - VILT)
TYP
MAX
UNITS
NOTES
VIS Type Input Buffer
V
5.5
V
1.18
1.35
V
Schmitt Trigger
1.40
1.61
1.81
V
Schmitt Trigger
VHYS
350
423
492
mV
Input Leakage
(VIN = VSS or VDDVARIO)
IIH
-10
+10
uA
Note 7.8
Input Leakage
(VIN = 5.5V)
IIH
120
uA
Note 7.8, Note 7.9
Input Capacitance
CIN
2.5
pF
Low Output Level
VOL
0.4
V
IOL = 12mA
High Output Level
VOH
V
IOH = -12mA
VO12 Type Buffer
VDDVARIO - 0.4
VOD12 Type Buffer
VOL
0.4
V
IOL = 12mA
VOL
0.4
V
IOL = 8mA
Low Output Level
VOL
0.4
V
IOL = 8mA
High Output Level
VOH
VDDVARIO - 0.4
V
IOH = -8mA
Low Input Level
VILCK
-0.3
0.5
V
High Input Level
VIHCK
1.4
3.6
V
Low Output Level
VOD8 Type Buffer
Low Output Level
VO8 Type Buffer
ICLK Input Buffer
SMSC LAN9221/LAN9221i
143
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 7.7 I/O Buffer Characteristics VDDVARIO=2.5V +/- 10%
PARAMETER
SYMBOL
MIN
Low Input Level
VILI
-0.3
High Input Level
VIHI
Negative-Going Threshold
VILT
0.78
Positive-Going Threshold
VIHT
Schmitt Trigger Hysteresis
(VIHT - VILT)
TYP
MAX
UNITS
NOTES
VIS Type Input Buffer
V
5.5
V
0.94
1.1
V
Schmitt Trigger
1.13
1.32
1.51
V
Schmitt Trigger
VHYS
304
384
472
mV
Input Leakage
(VIN = VSS or VDDVARIO)
IIH
-10
+10
uA
Note 7.8
Input Leakage
(VIN = 5.5V)
IIH
120
uA
Note 7.8, Note 7.9
Input Capacitance
CIN
2.5
pF
Low Output Level
VOL
0.4
V
IOL = 9mA
High Output Level
VOH
V
IOH = -9mA
VO12 Type Buffer
VDDVARIO - 0.4
VOD12 Type Buffer
Low Output Level
VOL
0.4
V
IOL = 9mA
VOL
0.4
V
IOL = 6mA
Low Output Level
VOL
0.4
V
IOL = 6mA
High Output Level
VOH
VDDVARIO - 0.4
V
IOH = -6mA
Low Input Level
VILCK
-0.3
0.5
V
High Input Level
VIHCK
1.4
3.6
V
VOD8 Type Buffer
Low Output Level
VO8 Type Buffer
ICLK Input Buffer
Revision 2.6 (12-04-08)
144
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 7.8 I/O Buffer Characteristics VDDVARIO=1.8V +/- 10%
PARAMETER
SYMBOL
MIN
Low Input Level
VILI
-0.3
High Input Level
VIHI
Negative-Going Threshold
VILT
0.54
Positive-Going Threshold
VIHT
Schmitt Trigger Hysteresis
(VIHT - VILT)
TYP
MAX
UNITS
NOTES
VIS Type Input Buffer
V
5.25
V
0.69
0.83
V
Schmitt Trigger
0.878
1.06
1.24
V
Schmitt Trigger
VHYS
277
368
525
mV
Input Leakage
(VIN = VSS or VDDVARIO)
IIH
-10
+10
uA
Note 7.8
Input Leakage
(VIN = 5.25V)
IIH
120
uA
Note 7.8, Note 7.9
Input Capacitance
CIN
2.5
pF
Low Output Level
VOL
0.4
V
IOL = 4mA
High Output Level
VOH
V
IOH = -4mA
VO12 Type Buffer
VDDVARIO - 0.4
VOD12 Type Buffer
Low Output Level
VOL
0.4
V
IOL = 4mA
VOL
0.4
V
IOL = 3mA
Low Output Level
VOL
0.4
V
IOL = 3mA
High Output Level
VOH
VDDVARIO - 0.4
V
IOH = -3mA
Low Input Level
VILCK
-0.3
0.5
V
High Input Level
VIHCK
1.4
3.6
V
VOD8 Type Buffer
Low Output Level
VO8 Type Buffer
ICLK Input Buffer
Note 7.8
This specification applies to all inputs and tri-stated bi-directional pins. Internal pull-down
and pull-up resistors add +/- 50uA per-pin (typical). When operating at reduced VDDVARIO
voltage levels (less than 3.0V), do not rely on internal pull-up and pull-down resistors to
determine signal state. Refer to the individual signal descriptions in Chapter 2, Pin
Description and Configuration for more information.
Note 7.9
This is the total VIN input leakage for the entire device. This value should be divided by
the number of pins driven to VIN MAX to calculate per-pin leakage. For example, if 10 pins
are driven to the maximum operational limit for V IN (5.5V or 5.25V, dependant on
VDDVARIO), the per-pin input leakage is the maximum input leakage current divided by
10.
SMSC LAN9221/LAN9221i
145
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 7.9 100BASE-TX Transceiver Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Peak Differential Output Voltage
High
VPPH
950
-
1050
mVpk
Note 7.10
Peak Differential Output Voltage
Low
VPPL
-950
-
-1050
mVpk
Note 7.10
Signal Amplitude Symmetry
VSS
98
-
102
%
Note 7.10
Signal Rise & Fall Time
TRF
3.0
-
5.0
nS
Note 7.10
Rise & Fall Time Symmetry
TRFS
-
-
0.5
nS
Note 7.10
Duty Cycle Distortion
DCD
35
50
65
%
Note 7.11
Overshoot & Undershoot
VOS
-
-
5
%
1.4
nS
Jitter
Note 7.12
Note 7.10 Measured at the line side of the transformer, line replaced by 100Ω (+/- 1%) resistor.
Note 7.11 Offset from16 nS pulse width at 50% of pulse peak
Note 7.12 Measured differentially.
Table 7.10 10BASE-T Transceiver Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Transmitter Peak Differential
Output Voltage
VOUT
2.2
2.5
2.8
V
Note 7.13
Receiver Differential Squelch
Threshold
VDS
300
420
585
mV
Note 7.13 Min/Max voltages guaranteed as measured with 100Ω resistive load.
Revision 2.6 (12-04-08)
146
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
7.7
Clock Circuit
The LAN9221/LAN9221i can accept either a 25MHz crystal (preferred) or a 25 MHz single-ended clock
oscillator (±50 PPM) input. The LAN9221/LAN9221i shares the 25MHz clock oscillator input (CLKIN)
with the crystal input XTAL1/CLKIN. If the single-ended clock oscillator method is implemented, XTAL2
should be left unconnected and CLKIN should be driven with a nominal 0-3.3V clock signal. The input
clock duty cycle is 40% minimum, 50% typical and 60% maximum.
It is recommended that a crystal utilizing matching parallel load capacitors be used for the
LAN9221/LAN9221i crystal input/output signals (XTAL1, XTAL2). See Table 7.11, "LAN9221/LAN9221i
Crystal Specifications" for crystal specifications. Refer to application note AN10.7 - “Parallel Crystal
Circuit Input Voltage Control” for additional information.
Table 7.11 LAN9221/LAN9221i Crystal Specifications
PARAMETER
SYMBOL
MIN
NOM
Crystal Cut
MAX
UNITS
NOTES
AT, typ
Crystal Oscillation Mode
Fundamental Mode
Crystal Calibration Mode
Parallel Resonant Mode
Frequency
Ffund
-
25.000
-
MHz
Ftol
-
-
+/-50
PPM
Note 7.14
Frequency Stability Over Temp
Ftemp
-
-
+/-50
PPM
Note 7.14
Frequency Deviation Over Time
Fage
-
+/-3 to 5
-
PPM
Note 7.15
-
-
+/-50
PPM
Note 7.16
oC
Frequency Tolerance @ 25
Total Allowable PPM Budget
Shunt Capacitance
CO
-
7 typ
-
pF
Load Capacitance
CL
-
20 typ
-
pF
Drive Level
PW
300
-
-
uW
Equivalent Series Resistance
R1
-
-
50
Ohm
Operating Temperature Range
Note 7.17
-
Note 7.18
oC
LAN9221/LAN9221i
XTAL1/CLKIN Pin Capacitance
-
3 typ
-
pF
Note 7.19
LAN9221/LAN9221i XTAL2 Pin
Capacitance
-
3 typ
-
pF
Note 7.19
Note 7.14 The maximum allowable values for Frequency Tolerance and Frequency Stability are
application dependant. Since any particular application must meet the IEEE +/-50 PPM
Total PPM Budget, the combination of these two values must be approximately +/-45 PPM
(allowing for aging).
Note 7.15 Frequency Deviation Over Time is also referred to as Aging.
Note 7.16 The total deviation for the Transmitter Clock Frequency is specified by IEEE 802.3u as
+/- 50 PPM.
Note 7.17 0oC for commercial version, -40oC for industrial version.
Note 7.18 +70oC for commercial version, +85oC for industrial version.
Note 7.19 This number includes the pad, the bond wire and the lead frame. PCB capacitance is not
included in this value. The XTAL1/CLKIN and XTAL2 pin and PCB capacitance values are
required to accurately calculate the value of the two external load capacitors. These two
external load capacitors determine the accuracy of the 25.000 MHz frequency.
SMSC LAN9221/LAN9221i
147
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 8 Package Outline
8.1
56-QFN Package
Figure 8.1 56 Pin QFN Package Definition
Table 8.1 56 Pin QFN Package Parameters
A
A1
A2
D/E
D1/E1
D2/E2
L
b
e
MIN
0.70
0.00
~
7.85
7.55
5.75
0.30
0.18
NOMINAL
~
0.02
~
8.00
~
5.90
~
0.25
0.50 Basic
MAX
1.00
0.05
0.90
8.15
7.95
6.05
0.50
0.30
REMARKS
Overall Package Height
Standoff
Mold Cap Thickness
X/Y Body Size
X/Y Mold Cap Size
X/Y Exposed Pad Size
Terminal Length
Terminal Width
Terminal Pitch
Notes:
1. All dimensions are in millimeters.
2. Position tolerance of each terminal and exposed pad is ± 0.05 mm at maximum material condition.
Dimension “b” applies to plated terminals and is measured between 0.15 and 0.30 mm from the
terminal tip.
3. The pin 1 identifier may vary, but is always located within the zone indicated.
Revision 2.6 (12-04-08)
148
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Figure 8.2 56 Pin QFN Recommended PCB Land Pattern
SMSC LAN9221/LAN9221i
149
DATASHEET
Revision 2.6 (12-04-08)
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Chapter 9 Revision History
Table 9.1 Customer Revision History
REVISION LEVEL & DATE
SECTION/FIGURE/ENTRY
CORRECTION
Rev. 2.5
(11-13-08)
All
Fixed various typos
Rev. 2.4
(10-24-08)
All
Fixed various typos
Table 7.1 on page 140 and
Table 7.2 on page 141
Added power consumption values.
Section 7.5, "Worst Case
Current Consumption," on
page 142
Updated with current consumption values for
various VDDVARIO values.
Section 7.6, "DC Electrical
Specifications," on page 143
Added input capacitance and input leakage values.
Section 3.8, "General
Purpose Timer (GP Timer),"
on page 38
Changed incorrect “GPT_CNT” reference to
“GPT_LOAD”: “On a reset, or when the
TIMER_EN bit changes from set ‘1’ to cleared ‘0,’
the GPT_LOAD field is initialized to FFFFh.”
Section 5.3.23, "E2P_CMD
– EEPROM Command
Register," on page 103
Corrected MAC Address Loaded (bit 8) type from
“RO” to “R/WC”
Table 7.11 on page 147
Updated crystal specifications:
Drive Level: 300uW
ESR: 50 Ohms.
Note 7.9 on page 145
Note following I/O Buffer Characteristics table
modified:
Rev. 2.3
(08-18-08)
Changed from: ".....the per-pin input leakage is 10
divided by the maximum input leakage current."
to: ".....the per-pin input leakage is the maximum
input leakage current divided by 10."
Rev. 2.2
(06-19-08)
Revision 2.6 (12-04-08)
Figure 1.2, "Internal Block
Diagram"
Diagram redone.
The word “Core” was added to the regulator block
title.
Table 2.4, “System and
Power Signals,” on page 18
Changed VDD_CORE/VDD18CORE bulk
capacitor value from 10uF to 4.7uF.
150
DATASHEET
SMSC LAN9221/LAN9221i
High-Performance 16-bit Non-PCI 10/100 Ethernet Controller with Variable Voltage I/O
Datasheet
Table 9.1 Customer Revision History (continued)
REVISION LEVEL & DATE
SECTION/FIGURE/ENTRY
Rev. 2.2
(06-10-08)
Auto-negotiation
Advertisement on page 121
Bits 9 and 15 relabeled as Reserved, Read-Only
(RO), with a default of 0.
Auto-negotiation
Advertisement on page 121
Fixed definition of bits 11:10 when equal to “11” by
adding “advertise support for..” to beginning of
definition. Also added note stating “When both
symmetric PAUSE and asymmetric PAUSE
support are advertised, the device will only be
configured to, at most, one of the two settings
upon auto-negotiation completion.”
Section 3.5, "Wake-up
Frame Detection," on
page 27 and Section 5.4.1,
"MAC_CR—MAC Control
Register," on page 107
Added note: “When wake-up frame detection is
enabled via the WUEN bit of the WUCSR—Wakeup Control and Status Register, a broadcast wakeup frame will wake-up the device despite the state
of the Disable Broadcast Frame (BCAST) bit in the
MAC_CR—MAC Control Register.”
Section 5.4.12,
"WUCSR—Wake-up Control
and Status Register," on
page 116
Fixed typo in bit 9: “... Mac Address [1:0] bit set to
0.” was changed to “...Mac Address [0] bit set to 0.”
Section 3.6.1.1, "RX
Checksum Calculation," on
page 33
“checksum = [B0, B1] + C0 + [B2, B3] + C1 + …
+ [0, BN] + CN-1” changed to “checksum = [B1,
B0] + C0 + [B3, B2] + C1 + … + [0, BN] + CN-1”
Section 2.2, “External PullUp/Pull-Down Resistors
Added section. Added references to this section
throughout the pin description tables as applicable.
Rev. 2.1
(05-13-08)
Section 1.1, "Block
Diagram"
Removed the system memory block and arrow
above the microprocessor/ microcontroller
Rev. 1.92
(10-22-07)
Chapter 2 Pin Description
and Configurationon
page 15
Pin assignment information re-organized into
separate table.
EECLK pin description in
Chapter 2 Pin Description
and Configurationon
page 15
Note added to EECLK pin description to indicate
proper usage.
SMSC LAN9221/LAN9221i
151
CORRECTION
DATASHEET
Revision 2.6 (12-04-08)