SP9T/10T Antenna Switch Module for GSM and UMTS/CDMA Dual Mode Handset CXM3519ER Description The CXM3519ER is a SP9T/SP10T antenna switch module for GSM and UMTS/CDMA dual-mode handset. This IC has a built-in dual low pass filter and a +1.8V CMOS compatible decoder. The Sony GaAs junction gate pHEMT (JPHEMT) MMIC process is used for low insertion loss and high linearity. The device has low BOM and small mount Area with no DC blocking capacitor. Features Low insertion loss (SP10T): 0.85dB (Typ.) Tx1 (GSM Low Band Tx) 0.88dB (Typ.) Tx2 (GSM High Band Tx) 0.50dB (Typ.) TRx1 (UMTS Band I) Low insertion loss (SP9T): 0.85dB (Typ.) Tx1 (GSM Low Band Tx) 0.85dB (Typ.) Tx2 (GSM High Band Tx) 0.47dB (Typ.) TRx1 (UMTS Band I) High attenuation: 35dB (Typ.) On Tx1 path @1648 – 1830MHz 33dB (Typ.) On Tx2 path @3420 – 3820MHz Low voltage operation: VDD = +2.5V No DC blocking capacitors Small package: VQFN-26P (3.0mm × 3.8mm × 0.8mm Typ.) Lead-Free and RoHS compliant Structure GaAs Junction-gate PHEMT MMIC Switch, CMOS Decoder and Dual-LPF. Note on Handling - GaAs MMIC’s are ESD sensitive devices. Special handling precautions are required. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E07Y05C86 CXM3519ER Block Diagram (SP9T/SP10T) TRx1 TRx2 TRx3 LPF1 Ant TRx4/GND Tx1 Tx2 Decoder Logic LPF2 Rx1 Rx2 Rx3 Rx4 Tx1 GND GND Tx2 GND Pin Configuration 13 12 11 10 9 15 7 Ant Rx4 16 6 GND Rx3 17 VQFN-26P PKG (3.0mm × 3.8mm × 0.8mm Typ.) 5∗ TRx4/GND Rx2 18 Top View 4 TRx3 Rx1 19 3 GND TRx1 20 2 TRx2 GND 21 1 GND 22 23 24 25 26 CTLA GND CTLB GND CTLC 8 CTLD 14 VDD GND ∗ Pin 5 SP9T : Connect to GND directly SP10T : TRx4 -2- CXM3519ER Pin Description Pin No. Symbol Pin No. Symbol 1 GND 14 GND 2 TRx2 15 GND 3 GND 16 Rx4 4 TRx3 17 Rx3 5 TRx4/GND 18 Rx2 6 GND 19 Rx1 7 Ant 20 TRx1 8 GND 21 GND 9 GND 22 VDD 10 Tx2 (DCS/PCS) 23 CTLD 11 GND 24 CTLC 12 GND 25 CTLB 13 Tx1 (GSM850/900M) 26 CTLA -3- CXM3519ER RF Switch (SP9T/SP10T) Ant F1 F2 F14 F8 F16 F18 F20 F15 F17 F19 F21 F9 F3 LPF1 F7 F10 LPF2 Tx1 F4 F11 Rx1 Tx2 F5 F6 F12 Rx2 F13 Rx3 Rx4 TRx2 TRx1 TRx3 TRx4/GND Truth Table State *1 *2 Active path Switch state*2 Vctl state A B C D F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 1 Tx1 H H L L H L L L L L L L H H H H H L H L H L H L H 2 Tx2 H L L L L H L L L L L H L H H H H L H L H L H L H 3 Rx1*1 L L L L L L H L L L L H H L H H H H H L H L H L H 4 Rx2*1 L L H L L L L H L L L H H H L H H H H L H L H L H 5 Rx3*1 L H H L L L L L H L L H H H H L H H H L H L H L H 6 Rx4*1 L H L L L L L L L H L H H H H H L H H L H L H L H 7 TRx1 H L H L L L L L L L H H H H H H H L L L H L H L H 8 TRx2 H H H L L L L L L L L H H H H H H L H H L L H L H 9 TRx3 H L H H L L L L L L L H H H H H H L H L H H L L H 10 TRx4 H H H H L L L L L L L H H H H H H L H L H L H H L Each Rx path can be used from 869MHz to 1990MHz frequency, user can select these Rx paths changeably. State “L” means a switch “OFF”, state “H” means a switch “ON”. -4- CXM3519ER Electrical Characteristics Supply Voltage (Ta = 25°C) Item Min. Typ. Max. Unit 2.5 2.65 3.3 V State Min. Typ. Max. High 1.5 1.80 3.3 Low 0 — 0.3 Bias voltage (VDD) Logic Value (Ta = 25°C) Item Control voltage (CTL-A/B/C/D) Absolute Maximum Ratings Item Ratings Bias voltage (VDD) 4V (Ta: +25°C) Control voltage (CTL-A/B/C/D) 4V (Ta: +25°C) Maximum input power (Tx1) +36dBm (Duty cycle = 12.5%) (Ta: +25°C) Maximum input power (Tx2) +34dBm (Duty cycle = 12.5%) (Ta: +25°C) Maximum input power (TRx1, 2, 3, 4) +32dBm (Ta: +25°C) Maximum input power (Rx1, 2, 3, 4) +13dBm (Ta: +25°C) Operating temperature –20 to +90°C Storage temperature –65 to +150°C -5- Unit V CXM3519ER Recommended Circuit 1 (SP9T) 13 Rx2 Rx1 TRx1 GND GND GND Tx2 9 14 8 15 7 16 6 17 VQFN-26P PKG (3.0mm × 3.8mm × 0.8mm Typ.) 5 18 Top View 4 19 3 20 2 21 1 VDD 22 23 24 25 GND C1 ANT GND L1 ∗GND TRx3 GND TRx2 GND 26 CTLA Rx3 10 CTLB Rx4 11 CTLC GND 12 CTLD GND GND Tx1 Ex.) GSM (4 bands) / UMTS (3 bands) C2 Note) 1. No DC blocking capacitors are required on all RF ports. 2. The DC levels of all RF ports are GND. 3. L1 inductor (22nH) and C1 capacitor (22pF) are recommended on Ant port for ESD protection. 4. C2 capacitor (100pF) is recommended. 5. Connect Pin 5 to GND directly. -6- CXM3519ER Electrical Characteristics (Recommended Circuit 1 (SP9T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Insertion loss Symbol I.L Min. Typ. Max. Ant-Tx1 Path *1 — 0.85 1.00 Ant-Tx2 *2 — 0.85 1.05 Ant-TRx1 (Tx) *3 — 0.47 0.62 Ant-TRx1 (Rx) *4 — 0.48 0.63 Ant-TRx2 (Tx) *5 — 0.51 0.61 Ant-TRx2 (Rx) *6 — 0.57 0.72 Ant-TRx3 (Tx) *5 — 0.48 0.58 Ant-TRx3 (Rx) *6 — 0.56 0.71 *7 — 0.66 0.76 1.02 1.17 Ant-Rx1 Conditions *8 *7 Ant-Rx2 — *8 *7 Ant-Rx3 — *8 *7 Ant-Rx4 — *8 0.65 0.75 1.01 1.16 0.65 0.75 0.98 1.13 0.65 0.75 0.94 1.09 Unit dB Electrical characteristics are measured with all RF ports terminated in 50Ω and recommended circuit 1 (SP9T). *1 *2 *3 *4 *5 *6 *7 *8 Frequency = 824 to 915MHz, Frequency = 1710 to 1910MHz, Frequency = 1920 to 1980MHz, Frequency = 2110 to 2170MHz, Frequency = 824 to 894MHz, Frequency = 1710 to 1990MHz, Frequency = 869 to 960MHz, Frequency = 1805 to 1990MHz, Item Symbol Pin on Tx1: +34dBm C.W. Pin on Tx2: +32dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on Ant: +10dBm C.W. Pin on Ant: +10dBm C.W. Path Conditions Min. Typ. Max. Unit Active path: Tx1-Ant (State1) Tx1-Rx1 35 42 — Tx1-Rx2 35 42 — Tx1-Rx3 35 42 — 35 42 — 35 39 — 45 54 — Tx1-Rx4 Tx1-TRx1 824 to 915MHz Tx1-TRx2 Tx1-TRx3 Tx1-Tx2 Isolation ISO. Tx2-Ant 1648 to 1830MHz 45 57 — 20 23 — 20 22 — 25 28 — Active path: Tx2-Ant (State2) Tx2-Rx1 32 37 — Tx2-Rx2 32 37 — Tx2-Rx3 32 37 — 32 38 — 30 33 — Tx2-TRx2 40 49 — Tx2-TRx3 40 44 — Tx2-Tx1 20 26 — Tx2-Rx4 Tx2-TRx1 1710 to 1910MHz -7- dB CXM3519ER Electrical Characteristics (Recommended Circuit 1 (SP9T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Symbol Path Conditions Min. Typ. Max. TRx1-Rx1 17 19 — TRx1-Rx2 20 27 — TRx1-Rx3 30 34 — 35 41 — 35 42 — TRx1-Tx2 25 30 — TRx1-TRx2 40 45 — TRx1-TRx3 35 42 — Unit Active path: TRx1-Ant (State7) TRx1-Rx4 TRx1-Tx1 1920 to 1980MHz Active path: TRx2-Ant (State8) TRx2-Rx1 35 40 — TRx2-Rx2 35 41 — TRx2-Rx3 35 43 — TRx2-Rx4 40 45 — 35 40 — TRx2-Tx2 35 42 — TRx2-TRx1 30 37 — TRx2-TRx3 30 36 — TRx2-Tx1 Isolation ISO. 824 to 849MHz TRx2-Rx1 25 32 — TRx2-Rx2 25 33 — TRx2-Rx3 30 35 — TRx2-Rx4 30 38 — 45 56 — TRx2-Tx2 25 32 — TRx2-TRx1 25 29 — TRx2-TRx3 25 31 — TRx3-Rx1 35 41 — TRx3-Rx2 35 42 — TRx3-Rx3 35 43 — 40 46 — TRx2-Tx1 1710 to 1910MHz Active path: TRx3-Ant (State9) TRx3-Rx4 TRx3-Tx1 824 to 849MHz 35 40 — TRx3-Tx2 40 43 — TRx3-TRx1 30 37 — TRx3-TRx2 30 37 — TRx3-Rx1 25 33 — TRx3-Rx2 25 33 — TRx3-Rx3 30 35 — 30 38 — TRx3-Rx4 TRx3-Tx1 1710 to 1910MHz 45 52 — TRx3-Tx2 25 33 — TRx3-TRx1 25 30 — TRx3-TRx2 25 30 — -8- dB CXM3519ER Electrical Characteristics (Recommended Circuit 1 (SP9T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Symbol Path Conditions TRx: 835MHz State7 TRx1-Ant IMD2 TRx2-Ant TRx3-Ant Intermodulation distortion level in Rx band TRx1-Ant IMD3 TRx2-Ant TRx3-Ant Min. Typ. Max. Ant: 45MHz *1 — –119 –105 Ant: 1715MHz *2 — –118 –105 TRx: 1880MHz State7 Ant: 80MHz *3 — –108 –103 Ant: 3840MHz *4 — –110 –105 TRx: 1950MHz State7 Ant: 190MHz *5 — –108 –103 Ant: 4090MHz *6 — –117 –105 TRx: 835MHz State8 Ant: 45MHz *1 — –119 –105 Ant: 1715MHz *2 — –117 –105 TRx: 1880MHz State8 Ant: 80MHz *3 — –107 –102 Ant: 3840MHz *4 — –107 –102 TRx: 1950MHz State8 Ant: 190MHz *5 — –109 –104 Ant: 4090MHz *6 — –116 –105 TRx: 835MHz State9 Ant: 45MHz *1 — –118 –105 Ant: 1715MHz *2 — –117 –105 TRx: 1880MHz State9 Ant: 80MHz *3 — –106 –101 Ant: 3840MHz *4 — –110 –105 TRx: 1950MHz State9 Ant: 190MHz *5 — –107 –102 Ant: 4090MHz *6 — –118 –105 TRx: 835MHz State7 Ant: 790MHz *7 — –108 –103 Ant: 2550MHz *8 — –110 –105 TRx: 1880MHz State7 Ant: 1800MHz *9 — –107 –102 Ant: 5720MHz *10 — –112 –105 TRx: 1950MHz State7 Ant: 1760MHz *11 — –107 –102 Ant: 6040MHz *12 — –115 –105 TRx: 835MHz State8 Ant: 790MHz *7 — –106 –101 Ant: 2550MHz *8 — –110 –105 TRx: 1880MHz State8 Ant: 1800MHz *9 — –105 –100 Ant: 5720MHz *10 — –110 –105 TRx: 1950MHz State8 Ant: 1760MHz *11 — –105 –100 Ant: 6040MHz *12 — –112 –105 TRx: 835MHz State9 Ant: 790MHz *7 — –108 –103 Ant: 2550MHz *8 — –110 –105 TRx: 1880MHz State9 Ant: 1800MHz *9 — –105 –100 Ant: 5720MHz *10 — –106 –101 TRx: 1950MHz State9 Ant: 1760MHz *11 — –105 –100 Ant: 6040MHz *12 — –110 –105 Unit dBm Electrical characteristics are measured with all RF ports terminated in 50Ω and recommended circuit 1 (SP9T). *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz, Ant port: –15dBm, 45MHz Ant port: –15dBm, 1715MHz Ant port: –15dBm, 80MHz Ant port: –15dBm, 3840MHz Ant port: –15dBm, 190MHz Ant port: –15dBm, 4090MHz Ant port: –15dBm, 790MHz Ant port: –15dBm, 2550MHz Ant port: –15dBm, 1800MHz Ant port: –15dBm, 5720MHz Ant port: –15dBm, 1760MHz Ant port: –15dBm, 6040MHz -9- CXM3519ER Electrical Characteristics (Recommended Circuit 1 (SP9T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Symbol Path Tx1-Ant *1 Tx2-Ant *2 Harmonics TRx1-Ant *3 Harm TRx2-Ant *3 TRx3-Ant *3 Conditions 2nd harmonic 1648 to 1698MHz 1780 to 1830MHz 3rd harmonic 2472 to 2547MHz 2670 to 2745MHz 2nd harmonic 3420 to 3570MHz 3700 to 3820MHz 3rd harmonic 5130 to 5355MHz 5550 to 5730MHz 2nd harmonic 3840 to 3960MHz 3rd harmonic 5760 to 5940MHz 2nd harmonic 3840 to 3960MHz 3rd harmonic 5760 to 5940MHz 2nd harmonic 3840 to 3960MHz 3rd harmonic 5760 to 5940MHz Min. Typ. Max. — –49 –36 — –44 –36 — –53 –36 — –45 –36 — –65 –36 — –63 –36 — –63 –36 — –61 –36 — –65 –36 — –58 –36 C.W. Pin = +34dBm C.W. Pin = +32dBm C.W. Pin = +26dBm Unit dBm C.W. Pin = +26dBm C.W. Pin = +26dBm Electrical characteristics are measured with all RF ports terminated in 50Ω and recommended circuit 1 (SP9T). *1 *2 *3 Frequency = 824 to 915MHz, Pin on Tx1: +34dBm C.W. Frequency = 1710 to 1910MHz, Pin on Tx2: +32dBm C.W. Frequency = 1920 to 1980MHz, Pin on TRx1 or TRx2 or TRx3: +26dBm C.W. Item Symbol Path Tx1-Ant Attenuation ATT Tx2-Ant Item Symbol Switching time Ts Control current Ictl Supply current IDD V.S.W.R. V.S.W.R. Conditions Min. Typ. Max. Unit 1648 to 1830MHz 2fo 25 35 — 2472 to 2745MHz 3fo 25 35 — 3296 to 3660MHz 4fo 20 24 — 3420 to 3820MHz 2fo 25 33 — 5130 to 5730MHz 3fo 25 32 — Min. Typ. Max. Unit 2 5 μs — 10 μA Active mode 0.22 0.4 mA 824 to 2170MHz 1.2 Path Conditions 90% OFF to 90% ON All ports in active paths - 10 - dB — CXM3519ER Recommended Circuit 2 (SP10T) 13 Rx2 Rx1 TRx1 GND GND Tx2 GND 15 7 16 6 17 VQFN-26P PKG (3.0mm × 3.8mm × 0.8mm Typ.) 5 18 Top View 4 19 3 20 2 21 1 VDD 22 23 24 25 GND C1 ANT GND L1 TRx4 TRx3 GND TRx2 GND 26 CTLA Rx3 9 8 CTLB Rx4 10 14 CTLC GND 11 12 CTLD GND GND Tx1 Ex.) GSM (4 bands) / UMTS (4 bands) C2 Note) 1. No DC blocking capacitors are required on all RF ports. 2. DC levels of all RF ports are GND. 3. L1 inductor (22nH) and C1 capacitor (22pF) are recommended on Ant port for ESD protection. 4. C2 capacitor (100pF) is recommended. - 11 - CXM3519ER Electrical Characteristics (Recommended Circuit 2 (SP10T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Insertion loss Symbol I.L Path Min. Typ. Max. Ant-Tx1 *1 — 0.85 1.00 Ant-Tx2 *2 — 0.88 1.08 Ant-TRx1 (Tx) *3 — 0.50 0.65 Ant-TRx1 (Rx) *4 — 0.52 0.67 Ant-TRx2 (Tx) *5 — 0.53 0.63 Ant-TRx2 (Rx) *6 — 0.59 0.74 Ant-TRx3 (Tx) *5 — 0.49 0.59 Ant-TRx3 (Rx) *6 — 0.61 0.76 Ant-TRx4 (Tx) *7 — 0.40 0.50 Ant-TRx4 (Rx) *8 — 0.40 0.50 *9 — Ant-Rx1 Conditions *10 *9 Ant-Rx2 — *10 — *9 Ant-Rx3 *10 — *9 Ant-Rx4 *10 0.67 0.77 1.04 1.19 0.64 0.74 1.03 1.18 0.65 0.75 0.98 1.13 0.65 0.75 0.95 1.10 Unit dB Electrical characteristics are measured with all RF ports terminated in 50Ω and recommended circuit 2 (SP10T). *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 Frequency = 824 to 915MHz, Frequency = 1710 to 1910MHz, Frequency = 1920 to 1980MHz, Frequency = 2110 to 2170MHz, Frequency = 824 to 894MHz, Frequency = 1710 to 1990MHz, Frequency = 824 to 849MHz, Frequency = 869 to 894MHz, Frequency = 869 to 960MHz, Frequency = 1805 to 1990MHz, Item Pin on Tx1: +34dBm C.W. Pin on Tx2: +32dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx1: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on TRx2 or 3: +26dBm C.W. Pin on TRx4: +26dBm C.W. Pin on TRx4: +26dBm C.W. Pin on Ant: +10dBm C.W. Pin on Ant: +10dBm C.W. Min. Typ. Max. Tx1-Rx1 35 42 — Tx1-Rx2 35 42 — Tx1-Rx3 35 42 — Tx1-Rx4 35 42 — 35 39 — Tx1-TRx2 45 54 — Tx1-TRx3 45 57 — Tx1-TRx4 30 36 — 20 23 — Symbol Path Conditions Unit Active path: Tx1-Ant (State1) Tx1-TRx1 824 to 915MHz Tx1-Tx2 Isolation ISO. Tx2-Ant 1648 to 1830MHz 20 23 — 25 28 — Active path: Tx2-Ant (State2) Tx2-Rx1 32 37 — Tx2-Rx2 32 37 — Tx2-Rx3 32 37 — Tx2-Rx4 32 38 — 30 33 — Tx2-TRx2 40 49 — Tx2-TRx3 40 44 — Tx2-TRx4 20 26 — Tx2-Tx1 20 26 — Tx2-TRx1 1710 to 1910MHz - 12 - dB CXM3519ER Electrical Characteristics (Recommended Circuit 2 (SP10T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Symbol ISO. Isolation ISO. Path Conditions Active path: TRx1-Ant (State7) TRx1-Rx1 TRx1-Rx2 TRx1-Rx3 TRx1-Rx4 TRx1-Tx1 1920 to 1980MHz TRx1-Tx2 TRx1-TRx2 TRx1-TRx3 TRx1-TRx4 Active path: TRx2-Ant (State8) TRx2-Rx1 TRx2-Rx2 TRx2-Rx3 TRx2-Rx4 TRx2-Tx1 824 to 849MHz TRx2-Tx2 TRx2-TRx1 TRx2-TRx3 TRx2-TRx4 TRx2-Rx1 TRx2-Rx2 TRx2-Rx3 TRx2-Rx4 TRx2-Tx1 1710 to 1910MHz TRx2-Tx2 TRx2-TRx1 TRx2-TRx3 TRx2-TRx4 Active path: TRx3-Ant (State9) TRx3-Rx1 TRx3-Rx2 TRx3-Rx3 TRx3-Rx4 824 to 849MHz TRx3-Tx1 TRx3-Tx2 TRx3-TRx1 TRx3-TRx2 TRx3-TRx4 TRx3-Rx1 TRx3-Rx2 TRx3-Rx3 TRx3-Rx4 1710 to 1910MHz TRx3-Tx1 TRx3-Tx2 TRx3-TRx1 TRx3-TRx2 TRx3-TRx4 Active path: TRx4-Ant (State10) TRx4-Rx1 TRx4-Rx2 TRx4-Rx3 TRx4-Rx4 TRx4-Tx1 824 to 849MHz TRx4-Tx2 TRx4-TRx1 TRx4-TRx2 TRx4-TRx3 - 13 - Min. Typ. Max. 17 20 30 35 35 25 40 35 20 19 27 34 41 42 30 45 42 25 — — — — — — — — — 35 35 35 40 35 35 30 30 30 25 25 30 30 45 25 25 25 20 41 41 43 45 40 42 37 36 36 32 33 35 38 56 32 29 31 25 — — — — — — — — — — — — — — — — — — 35 35 35 40 35 40 30 30 30 25 25 30 30 45 25 25 25 17 41 42 43 46 40 44 37 37 34 33 33 35 38 52 34 30 30 21 — — — — — — — — — — — — — — — — — — 35 35 35 40 35 40 30 40 30 41 42 43 46 40 44 37 47 34 — — — — — — — — — Unit dB dB CXM3519ER Electrical Characteristics (Recommended Circuit 2 (SP10T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Symbol Path TRx1-Ant TRx2-Ant IMD2 TRx3-Ant TRx4-Ant Intermodulation distortion level in Rx band TRx1-Ant TRx2-Ant IMD3 TRx3-Ant TRx4-Ant TRx: 835MHz State7 TRx: 1880MHz State7 TRx: 1950MHz State7 TRx: 835MHz State8 TRx: 1880MHz State8 TRx: 1950MHz State8 TRx: 835MHz State9 TRx: 1880MHz State9 TRx: 1950MHz State9 TRx: 835MHz State10 TRx: 1880MHz State10 TRx: 1950MHz State10 TRx: 835MHz State7 TRx: 1880MHz State7 TRx: 1950MHz State7 TRx: 835MHz State8 TRx: 1880MHz State8 TRx: 1950MHz State8 TRx: 835MHz State9 TRx: 1880MHz State9 TRx: 1950MHz State9 TRx: 835MHz State10 TRx: 1880MHz State10 TRx: 1950MHz State10 Conditions Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 45MHz *1 Ant: 1715MHz *2 Ant: 80MHz *3 Ant: 3840MHz *4 Ant: 190MHz *5 Ant: 4090MHz *6 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Ant: 790MHz *7 Ant: 2550MHz *8 Ant: 1800MHz *9 Ant: 5720MHz *10 Ant: 1760MHz *11 Ant: 6040MHz *12 Min. — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Typ. –119 –118 –108 –110 –108 –117 –119 –117 –107 –107 –109 –116 –118 –117 –106 –110 –107 –118 –117 –116 –105 –110 –106 –118 –108 –110 –107 –112 –107 –115 –106 –110 –105 –110 –105 –112 –108 –110 –105 –106 –105 –110 –108 –110 –105 –105 –105 –110 Max. –105 –105 –103 –105 –103 –105 –105 –105 –102 –102 –104 –105 –105 –105 –101 –105 –102 –105 –105 –105 –100 –105 –101 –105 –103 –105 –102 –105 –102 –105 –101 –105 –100 –105 –100 –105 –103 –105 –100 –101 –100 –105 –103 –105 –100 –100 –100 –105 Unit dBm dBm Electrical characteristics are measured with all RF ports terminated in 50Ω and recommended circuit 2 (SP10T). *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 835MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1880MHz, TRx port: +20dBm, 1950MHz, TRx port: +20dBm, 1950MHz, Ant port: –15dBm, 45MHz Ant port: –15dBm, 1715MHz Ant port: –15dBm, 80MHz Ant port: –15dBm, 3840MHz Ant port: –15dBm, 190MHz Ant port: –15dBm, 4090MHz Ant port: –15dBm, 790MHz Ant port: –15dBm, 2550MHz Ant port: –15dBm, 1800MHz Ant port: –15dBm, 5720MHz Ant port: –15dBm, 1760MHz Ant port: –15dBm, 6040MHz - 14 - CXM3519ER Electrical Characteristics (Recommended Circuit 2 (SP10T)) (VDD = 2.65V, Vctl = 1.80V, Ta = 25°C) Item Symbol Path Tx1-Ant *1 Tx2-Ant *2 TRx1-Ant *3 Harmonics Harm TRx2-Ant *3 TRx3-Ant *3 TRx4-Ant *4 Conditions 2nd harmonic 1648 to 1698MHz 1780 to 1830MHz 3rd harmonic 2472 to 2547MHz 2670 to 2745MHz 2nd harmonic 3420 to 3570MHz 3700 to 3820MHz 3rd harmonic 5130 to 5355MHz 5550 to 5730MHz 2nd harmonic 3840 to 3960MHz 3rd harmonic 5760 to 5940MHz 2nd harmonic 3840 to 3960MHz 3rd harmonic 5760 to 5940MHz 2nd harmonic 3840 to 3960MHz 3rd harmonic 5760 to 5940MHz 2nd harmonic 1648 to 1698MHz 3rd harmonic 2472 to 2547MHz C.W. Pin = +34dBm C.W. Pin = +32dBm C.W. Pin = +26dBm Min. Typ. Max — –49 –36 — –44 –36 — –53 –36 — –45 –36 — –65 –36 — –63 –36 — –65 –36 — –62 –36 — –65 –36 — –60 –36 — –65 –36 — –65 –36 Unit dBm C.W. Pin = +26dBm C.W. Pin = +26dBm C.W. Pin = +26dBm Electrical characteristics are measured with all RF ports terminated in 50Ω and recommended circuit 2 (SP10T). *1 *2 *3 *4 Frequency = 824 to 915MHz, Frequency = 1710 to 1910MHz, Frequency = 1920 to 1980MHz, Frequency = 824 to 849MHz, Item Symbol Pin on Tx1: +34dBm C.W. Pin on Tx2: +32dBm C.W. Pin on TRx1 or TRx2 or TRx3: +26dBm C.W. Pin on TRx4: +26dBm C.W. Path Conditions Tx1-Ant Attenuation ATT Tx2-Ant Item Symbol Switching time Ts Control current Ictl Supply current IDD V.S.W.R. V.S.W.R. Typ. Max. Unit 1648 to 1830MHz 2fo 25 35 — 2472 to 2745MHz 3fo 25 35 — 3296 to 3660MHz 4fo 20 24 — 3420 to 3820MHz 2fo 25 33 — 5130 to 5730MHz 3fo 25 32 — Min. Typ. Max. Unit 2 5 μs — 10 μA Active mode 0.22 0.4 mA 824 to 2170MHz 1.2 Path Conditions 90% OFF to 90% ON All ports in active paths - 15 - Min. dB — CXM3519ER PCB Layout Template VQFN-26P-01 Macro (Reference) • PKG size : 3.8mm × 3.0mm • Pin pitch : 0.4mm : Land ∗ Metal mask thickness: 110µm : Mask (Open area) : Resist (Open area) PKG line 4.2 3.8 (PKG line) 0.62 [Detailed view A] 0.72 0.52 0.62 0.31 0.37 0.3 R0.2 C0.1 0.3 0.5 R0.05 3.4 1.9 1.5 0.99 1.8 1.04 3.0 (PKG line) 0.05 R0.2 0.2 0.1 R0.2 0.21 R0.2 0.15 0.26 0.4 ∗ Mask corner R = 0.05mm A - 16 - CXM3519ER Recommended PCB Design 1 (SP9T) Ex.) GSM (4 bands) / UMTS (3 bands) The positions of the light blue via holes and relative GND patterns are strongly recommended for getting stable attenuation. 0.78 1.20 1.67 1.72 (Unit: mm) 0.71 IC (VQFN-26P package) 0.28 PCB metal pattern GND via hole for LPF (Light blue) GND via hole for switch Independent GND with via hole The positions of these via holes are recommended for stable attenuation. - 17 - CXM3519ER Recommended PCB Design 2 (SP10T) Ex.) GSM (4 bands) / UMTS (4 bands) The positions of the light blue via holes and relative GND patterns are strongly recommended for getting stable attenuation. 0.78 1.20 1.67 1.72 (Unit: mm) 0.71 IC (VQFN-26P package) 0.28 PCB metal pattern GND via hole for LPF (Light blue) GND via hole for switch Independent GND with via hole The positions of these via holes are recommended for stable attenuation. - 18 - CXM3519ER Package Outline (Unit: mm) LEAD PLATING SPECIFICATIONS ITEM LEAD MATERIAL - 19 - SPEC. COPPER ALLOY SOLDER COMPOSITION Sn-Bi Bi:1-4wt% PLATING THICKNESS 5-18µm Sony Corporation