155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Features • Duplex LC Single Mode Transceiver • Small Form Factor Multi-sourced 2x5 Pin Package • Ultra Long reach SONET OC-3/SDH STM-1 Compliant • Single +3.3V Power Supply • LVPECL Differential Inputs and Outputs • LVPECL Signal Detection Output • Temperature Range: -40 to 85 ºC • Class 1 Laser International Safety Standard IEC 825 Compliant • Solder ability to MIL-STD-883, Method 2003 • Pin coating is Sn/Pb with minimum 2% Pb content • Flammability to UL94V0 • Humidity RH 5-85% (5-95% short term) to IEC 68-2-3 • Complies with Telcordia(Bellcore) GR-468-CORE • Uncooled laser diode with MQW structure • EMI Shielding Finger Optional • ATM 155 Mbps links • RoHS compliance available Absolute Maximum Rating Symbol Min. Max. Unit Power Supply Voltage Parameter Vcc 0 3.6 V Output Current Iout 0 30 mA Soldering Temperature - - 260 ºC Operating Temperature Topr -40 85 ºC Storage Temperature Tstg -40 85 ºC Note 10 seconds on leads only Recommended Operating Condition Symbol Min. Typ. Max. Unit Power Supply Voltage Parameter Vcc 3.1 3.3 3.5 V Operating Temperature (Case) Topr -40 - 85 ºC - - 155 - Mbps Data Rate LUMINENTOIC.COM Note 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Transmitter Specifications Parameter Symbol Min Typical Max Unit Notes Po -15 - -8 dBm C-13-155-F-SLC3A-12 Optical Optical Transmit Power Optical Transmit Power Po -5 - 0 dBm C-13-155-F-SLC5A-12 Output Center Wavelength λp 1261 1310 1360 nm C-13-155-F-SLC3A-12 Output Center Wavelength λp 1263 1310 1360 nm C-13-155-F-SLC5A-12 Output Spectrum Width ∆λrms - - 7.7 nm RMS(σ), C-13-155-F-SLC3A-12 Output Spectrum Width ∆λrms - - 3 nm RMS(σ), C-13-155-F-SLC5A-12 Extinction Ratio ER 8.2 - - dB C-13-155-F-SLC3A-12 Extinction Ratio ER 10 - - dB C-13-155-F-SLC5A-12 Output Eye Compliant with Bellcore GR-253-CORE and ITU recommendation G.957 Optical Rise Time tr - - 2 ns 10% to 90% Values Optical Fall Time tf - - 2 ns 10% to 90% Values RIN - - -116 dB/Hz TJ - - 1.2 ns Measured with 223-1 PRBS with 72 ones and 72 zeros. Symbol Min Typical Max Unit Notes Power Supply Current ICC - - 180 mA Transmitter Enable Voltage VEN 0 - 0.8 V Transmitter Disable Voltage VD 2 - Vcc V Data Input Current-Low IIL -200 - - µA Data Input Current-High IIH - - 200 µA Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Relative Intensity Noise Total Jitter Transmitter Specifications Parameter Electrical LUMINENTOIC.COM Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Receiver Specifications Parameter Symbol Min Typical Max Unit Notes Sensitivity1 - - - -32 dBm C-13-155-F-SLC3A-12 Sensitivity1 - - - -34 dBm C-13-155-F-SLC5A-12 Maximum Input Power Pin -7 - - dBm C-13-155-F-SLC3A-12 Maximum Input Power Pin -3 - - dBm C-13-155-F-SLC5A-12 Signal Detect-Asserted Pa - - -32 dBm Signal Detect-Asserted Pa - - -34 dbm Signal Detect-Deasserted Pd -48 - - dBm 1 - 4 dB 1100 - 1600 nm Symbol Min Typical Max Unit Note ICC - - 100 mA The current excludes the output load current VOL -Vcc -2.0 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V Signal Detect Output Voltage-Low VSDL -Vcc -2.0 -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 -0.74 V Optical Signal Detect-Hysteresis Wavelength of Operation Note1: Measured with 223-1 C-13-155-F-SLC3A-12 Measured on transition: low to high C-13-155-F-SLC5A-12 Measured on transition: low to high Measured on transition: high to low PRBS/BER=10-10 Receiver Specifications Parameter Electrical Power Supply Current Data Output Voltage-Low LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Connection Diagram PIN Symbol 1 RxGND Notes Directly connect this pin to the receiver ground plane 2 RxVcc +3.3V dc power for the receiver section 3 SD Active high on this indicates a received optical signal(LVPECL/LVTTL) 4 RD- Receiver Data Out Bar (LVPECL) 5 RD+ Receiver Data Out (LVPECL) 6 TxVcc +3.3V dc power for the trasmitter section 7 TxGND Directly connect this pin to the transmitter ground plane 8 Warnings TxDIS Transmitter disable (LVTTL) 9 TD+ Transmitter Data In (LVPECL) 10 TD- Transmitter Data In Bar (LVPECL) Attaching Posts LUMINENTOIC.COM The attaching posts are at case potential and may be connected to chassis ground. They are isolated from circuit ground. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Recommended Circuit Schematic PHY DEVICE TERMINATE AT TRANSCEIVER INPUTS Vcc(+3.3V) Z=50� TD- LVPECL 100� Z=50� TD+ 130� 1 3 TxGND TxVcc RD- RD+ 6 TxDIS TD+ 2 7 Tx Disable SD RxVcc Rx 8 TD- Tx 9 RxGND 10 4 130� 1�H Vcc(+3.3V) C2 C3 10�F Vcc(+3.3V) 1�H C1 5 LVTTL RD+ Z=50� LVPECL 100� RD- Z=50� 130� Vcc(+3.3V) 130� Z=50� 130� SD LVPECL 82� NOTE:C1=C2=C3=100nF TERMINATE AT DEVICE INPUTS The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Package Diagram C-13-155-F-SLC3(5)A-12 Units: mm (inches) (0.039±0.002) (0.070) (0.400) (0.020) ) (0.386) +( -(0.004) (0.150) (0.413) (0.374) (0.520) ) (0.535) +( -(0.004) ) (1.921) +( -(0.008) (0.280) (0.246) (0.200) (0.700) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Recommended Board Layout Hole Pattern DIMENSION IN MILLIMETER (INCHES) NOTES: 1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER. 2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS. 3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Recommended Panel mounting DIMENSION IN MILLIMETER (INCHES) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Ordering Information Available Options: C-13-155-F-SLC3A-12 C-13-155-F-SLC5A-12 C-13-155-F-SLC3A-12-G5 C-13-155-F-SLC5A-12-G5 Part numbering Definition: C - 13 - 155 - F - S LC TxPower Temperature Package -12 -RoHS • 13 = Wavelength 1310nm • Communication protocol (155Mbps) 155 = PECL Signal Detection Output • F = +3.3V SFF Transceiver, FP • Single mode fiber • Connector options • Tx Power range 3 = -15 to -8 dBm 5 = -5 to 0 dBm •Temperature A = -40 to 85 ºC • Package Blank = Standard package • -12 = Rubytech Customization • Ordering Information G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 9 LUMNDS1776-Nov1207 Rev A.0 155 Mbps Single Mode SFF LC Transceiver C-13-155-F-SLC3(5)A-12 Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 10 LUMNDS1776-Nov1207 Rev A.0