SOURCE C-15-1250C-FDFB

1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-sourced 2x5 Pin Package
• Complies with IEEE 802.3 Gigabit Ethernet
• 1310 nm/1550 nm Wavelength, DFB Laser
• Single +3.3V Power Supply
• LVPECL Differential Inputs and Outputs
• LVTTL Signal Detection Output [C-1x-1250C-FDFB-SLC2(4)]
• LVPECL Signal Detection Output [C-1x-1250-FDFB-SLC2(4)]
• Class 1 Laser International Safety Standard IEC 825
compliant
• Solderability to MIL-STD-883, Method 2003
• Pin Coating is Sn/Pb with minimum 2% Pb content
• Flammability to UL94V0
• Humidity RH 5-85% (5-90% short term) to IEC 68-2-3
• Complies with Bellcore TA-NWT-000983
• Uncooled laser diode with MQW structure
• 1.25 Gbps Ethernet Links application
• 1.06 Gbps Fiber Channel application
• RoHS compliance available
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Power Supply Voltage
Vcc
0
3.6
V
Output Current
Iout
0
30
mA
-
-
260
ºC
Tstg
-40
85
ºC
Symbol
Min.
Typ.
Max.
Unit
Vcc
3.1
3.3
3.5
V
1
Operating Temperature (Case)
Topr
-40
-
85
ºC
Operating Temperature (Case)1
Topr
0
-
70
ºC
-
-
1250
-
Mbps
Soldering Temperature
Storage Temperature
Unit
Note
10 seconds on leads only
Recommended Operating Condition
Parameter
Power Supply Voltage
Data Rate
Note 1 : Please refer to ordering information
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Optical Transmit Power
Po
-5
Optical Transmit Power
Po
0
Output center Wavelength
λ
Output center Wavelength
λ
Notes
-
0
dBm
C-1x-1250(C)-FDFB-SLC2
-
+5
dBm
C-1x-1250(C)-FDFB-SLC4
1280
1310
1340
nm
C-13-1250(C)-FDFB-SLC2(4)
1480
1550
1580
nm
C-15-1250(C)-FDFB-SLC2(4)
Optical
Output Spectrum Width
∆λ
-
-
1
nm
-20 dB width
Side Mode Suppression Ratio
Sr
30
35
-
dBm
CW
Extinction Ratio
ER
9
-
-
dB
Output Eye
Compliant with IEEE 802.3
Optical Rise Time
tr
-
-
0.26
ns
20% to 80% Values
Optical Fall Time
tf
-
-
0.26
ns
20% to 80% Values
RIN
-
-
-120
dB/Hz
TJ
-
-
0.27
ns
Relative Intensity Noise
Total Jitter
LUMINENTOIC.COM
Measured with 27-1 PRBS
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Power Supply Current
ICC
-
-
180
mA
Transmit Enable Voltage
VEN
0
-
0.8
V
VD
2.0
-
Vcc
V
Data Input Current-Low
IIL
-200
-
-
µA
Data Input Current-High
IIH
-
-
200
µA
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
These inputs are compatible with 10K, 10KH
and 100K ECL and PECL inputs
Symbol
Min
Typical
Max
Unit
Notes
-
-
-
-24
dBm
Maximum Input Power
Pin
-3
-
-
dBm
Signal Detect-Asserted
Pa
-
-
-24
dBm
Measured on transition: low to high
Signal Detect-Deasserted
Pd
-38
-
-
dBm
Measured on transition: high to low
1.0
-
-
dB
1100
-
1600
nm
Symbol
Min
Typical
Max
Unit
ICC
-
-
120
mA
Electrical
Transmit Disable Voltage
Maximum current is specified at
Vcc= Maximum @ maximum temperature
Receiver Specifications
Parameter
Optical
Sensitivity
Signal Detect-Hysteresis
Wavelength of Operation
Measured with 27-1 PRBS, BER = 10-12
Receiver Specifications
Parameter
Note
Electrical
Power Supply Current
Data Output Voltage-Low
VOL -Vcc
-2
-
-1.58
V
Data Output Voltage-High
VOH- Vcc
-1.1
-
-0.74
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-2
-
-1.58
V
Signal Detect Output Voltage-High
VSDH- Vcc
-1.1
-
-0.74
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-
-
0.5
V
Signal Detect Output Voltage-High
VSDH- Vcc
2.0
-
-
V
LUMINENTOIC.COM
The current excludes the output load
current
These outputs are compatible with 10K,
10KH and 100K ECL and LVPECL outputs
C-1x-1250-FDFB-SLC2(4)
C-1x-1250C-FDFB-SLC2(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Connection Diagram
Legal Notice
PIN
Symbol
1
RxGND
2
TxVcc
Notes
Directly connect this pin to the receiver ground plane
+3.3 V dc power for the receiver section
3
SD
Active high on this indicates a received optical signal(LVPECL/LVTTL)
4
RD-
Receiver Data Out Bar (LVPECL)
5
RD+
Receiver Dat Out (LVPECL)
6
TxVcc
+3.3 V dc power for the transmitter section
7
TxGND
Directly connect this pin to the transmitter ground plane
8
TxDIS
Transmitter disable (LVTTL)
9
TD+
Transmitter Data In (LVPECL)
10
TD-
Transmitter Data In Bar (LVPECL)
Attaching Posts
LUMINENTOIC.COM
The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Recommended Circuit Schematic
C-1x-1250-FDFB-SLC2(4)
PHY DEVICE
TERMINATE AT
TRANSCEIVER INPUTS
Vcc(+3.3V)
Z=50�
TD-
LVPECL
100�
Z=50�
1
2
3
130�
TxGND
TxVcc
RD-
RD+
6
TxDIS
7
SD
TD+
RxVcc
Rx
8
TD-
Tx
9
RxGND
10
4
TD+
1�H
Vcc(+3.3V)
C2
C3
130�
10�F
Vcc(+3.3V)
1�H
C1
5
RD+
Z=50�
LVPECL
100�
RD-
Z=50�
130�
Vcc(+3.3V)
130�
Z=50�
130�
SD
82�
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Recommended Circuit Schematic
C-1x-1250C-FDFB-SLC2(4)
Vcc(+3.3V)
TERMINATE AT
TRANSCEIVER INPUTS
Z=50
TD-
LVPECL
100
Z=50
1
2
3
130
TxGND
TxVcc
RD-
RD+
6
TxDIS
7
SD
TD+
RxVcc
Rx
8
TD-
Tx
9
RxGND
10
4
TD
1H
Vcc(+3.3V)
C2
C3
130
10F
Vcc(+3.3V)
1H
C1
5
RD+
Z=50
LVPECL
100
RD-
Z=50
130
130
Z=50
SD
TERMINATE AT
DEVICE INPUTS
NOTE:C1=C2=C3=100nF
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Printed Circuit Board Layout Consideration
A fiber-optic receiver employs a very high gain, wide bandwidth transimpedance amplifier. This amplifier detects and amplifies
signals that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the
receiver circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit.
To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must
be used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of
power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of
signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high
speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi filter
be used in both transmitter and receiver power supplies.
EMI and ESC Consideration
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs flush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis
ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the
gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of
the panel.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Recommended Board Layout Hole Pattern
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Package Diagram
Units: mm (inches)



(0.400)
)
(0.535) +(
-(0.004)
 


(0.520)
(0.)

)
(1.921) +(
-(0.008)


(0.150)


(0.020)


(0.039)±(0.002)
(0.070)


(0.280)


(0.386)
)
(0.386) +(
-(0.004)


(0.413)
 

(0.374)
(0.)

(0.)


(0.)
(0.086)
(0.)

(0.246)
(0.200)
(0.700)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
9
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Ordering Information
Available Options:
C-13-1250-FDFB-SLC2
C-13-1250C-FDFB-SLC2
C-15-1250-FDFB-SLC2
C-15-1250C-FDFB-SLC2
C-13-1250-FDFB-SLC2A
C-13-1250C-FDFB-SLC2A
C-15-1250-FDFB-SLC2A
C-15-1250C-FDFB-SLC2A
C-13-1250-FDFB-SLC4
C-13-1250C-FDFB-SLC4
C-15-1250-FDFB-SLC4
C-15-1250C-FDFB-SLC4
C-13-1250-FDFB-SLC4A
C-13-1250C-FDFB-SLC4A
C-15-1250-FDFB-SLC4A
C-15-1250C-FDFB-SLC4A
C-13-1250-FDFB-SLC2-G5
C-13-1250C-FDFB-SLC2-G5
C-15-1250-FDFB-SLC2-G5
C-15-1250C-FDFB-SLC2-G5
C-13-1250-FDFB-SLC2A-G5
C-13-1250C-FDFB-SLC2A-G5
C-15-1250-FDFB-SLC2A-G5
C-15-1250C-FDFB-SLC2A-G5
C-13-1250-FDFB-SLC4-G5
C-13-1250C-FDFB-SLC4-G5
C-15-1250-FDFB-SLC4-G5
C-15-1250C-FDFB-SLC4-G5
C-13-1250-FDFB-SLC4A-G5
C-13-1250C-FDFB-SLC4A-G5
C-15-1250-FDFB-SLC4A-G5
C-15-1250C-FDFB-SLC4A-G5
Part numbering Definition:
C - 1x - 1250(C) - FDFB - S LC Tx Power Temperature and packge
-RoHS
• 13 = Wavelength 1310 nm
15 = Wavelength 1550 nm
• Communication protocol
1250 = LVPEVL SD Output
1250C = LVTTL SD Output
• +3.3V SFF Transceiver, DFB
• Single mode fiber
• Connector options
• Tx Power Range
2 = Tx Power -5 to 0 dBm
4 = Tx Power 0 to +5 dBm
• Temperature and package
Blank = Commercial temperature (0 to 70℃)
A = Commercial temperature (-40 to 85℃)
• Ordering Information
Blank = RoHS non-compliant product
G5 = RoHS 5/6-compliant product (lead exemption)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
10
LUMNDS613-Oct2406
Rev. A.2
1.25 Gbps Single Mode SFF LC Transceiver
C-1x-1250(C)-FDFB-SLC2(4)
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
11
LUMNDS613-Oct2406
Rev. A.2