SOURCE SP-12-LR1-CDA

622 Mbps SFP Transceiver
SP-12-LR1
Features
• Compliant with OC12/STM-4 Standards
• Single 3.3 V supply
• 25 dB min. link budget
• 1310nm FP Laser, 40 km reach
• SFP MSA SFF-8074i compliant
• Bellcore GR-468 compliant
• Color coded bail latch: Red
• RoHS-5/6 compliant product(lead exemption)
• Digital Diagnostic SFF-8472 Compliant
General operating
Parameter
Supply Voltage
Total Current
Symbol
Min.
Typical
Max.
Unit
Vcc
3.135
3.3
3.465
V
Icc
-
-
300
mA
Power Supply Noise Rejectiona
PSR
100
-
-
mVp-p
Operating Temperature (-CXX)
Top
-5
-
70
ºC
Operating Temperature (-RXX)
Top
-20
-
85
ºC
Operating Temperature (-TXX)
Top
-40
-
85
ºC
Storage Temperature
Tst
-40
-
85
ºC
Data Rate OC12/STM-2
DR
-
622
-
Mbps
Symbol
Min
Typical
Max
Unit
POP
-3
0
+2
dBm
Average Launch Power Of Off Tx
POff
-
-
-30
dBm
Extinction Ratio
ER
8.2
-
-
dB
-
-
-
SONET/SDH compliant
a) 20Hz to 155MHz
Transmitter Specifications
Parameter
Optical Power
Eye Mask
Optical Jitter Generation
Jgen
-
-
0.002
UI
Optical Rise Timeb
tr
-
-
500
ps
Optical Fall Timeb
tf
-
500
ps
λ
1296
1310
1330
nm
∆λ
-
-
1.7
nm
-
0.5
1
dB
-
-
-120
dB/Hz
Mean Wavelength
Spectral Width (RMS)
Dispersion Penalty (at 40 Km)
Relative Intensity Noise
RIN
b) 20%-80% values
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS1501-Oct3105
Rev A.0
622 Mbps SFP Transceiver
SP-12-LR1
Transmitter Specifications (Electical)
Parameter
Input Differential Impedence
PECL Single Ended Data Input Swing
TxFault_Fault
TxFault_Normal
Symbol
Min
Typical
Max
Rin
80
100
120
Unit
Ω
Vin,p-p
250
-
1200
mV
Vfault
2
-
Vcc
V
Vnormal
Vee
-
Vee+0.5
V
TxDisable_Disable
Vd
2
-
Vcc
V
TxDisable_Enable
Ven
Vee
-
Vee+0.8
V
Parameter
Symbol
Min
Typical
Max
Unit
Receive Power Lowc
Rsens,low
-
-30
-28
dBm
Receive Power High
Rsens,high
-8
-
-
dBm
Damage Threshold For Receiver
Pin,damage
0
-
-
dBm
λ
1260
1310
1360
nm
-38
-
-
dBm
LOS De-assert
-
-
-28
dBm
LOS Hysteresis
0.5
-
-
dB
Receiver Specifications
Wavelengthd
LOS Assert
10-12
c)
at nominal wavelength
d) Operational over 1200 to 1625 nm range
Electrical Output
Parameter
Symbol
Min
Typical
Max
Unit
PECL Single Ended Data Output Swing
Vout, p-p
185
-
800
mV
Data Output Rise Time
tr
-
-
500
ps
Data Output Fall Time
tf
-
-
500
ps
Timing and Electrical
Parameter
Symbol
Min
Typical
Max
Unit
t_on
-
-
1
ms
Tx Disable Assert Time
t_off
-
-
10
µs
Time To Initialize, Including Reset Of Tx Fault
t_init
-
-
300
ms
Tx Disable Negate Time
Tx Fault Assert Time
t_fault
-
-
100
µs
Tx Disable To Reset
t_reset
10
-
-
µs
t_loss_on
-
-
100
µs
Los De-assert Time
t_loss_off
-
-
100
µs
Serial ID Clock Rate
f_serial_clock
-
-
100
KHz
2
-
-
V
Los Assert Time
RX_LOS Voltage (High)
RX_LOS Voltage (Low)
LOS Output Voltage-Fault
LOS Output Voltage-Normal
-
-
0.8
V
VLOS fault
2
-
Vcc
V
VLOSnormal
Vee
-
Vee+0.5
V
MOD_DEF (0:2)-High
Vh
2
-
Vcc
V
MOD_DEF (0:2)-LOW
Vl
Vee
-
Vee+0.5
V
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS1501-Oct3105
Rev A.0
622 Mbps SFP Transceiver
SP-12-LR1
Diagnostics
Parameter
Range
Accuracy
Unit
Calibration
Formula
Temperature (-CDA)
-5 to 70
±3
ºC
Internal
Tc(C)=Tad(16 bit signed twos complement)/256
Temperature (-RDA)
-20 to 85
±3
ºC
Internal
Tc(C)=Tad(16 bit signed twos complement)/256
Temperature (-TDA)
-40 to 85
±3
ºC
Internal
Tc(C)=Tad(16 bit signed twos complement)/256
Voltage
0 to Vcc
±0.1
V
Internal
V(Volts)=Vad(16 bit unsigned integer)*0.1
Bias current
0 to 120
±5
mA
External
I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset
TX Power
-3 to +2
±3 dB
dBm
External
TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer)
+TX_PWRoffset
RX Power
-28 to -8
±3 dB
dBm
External
RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4
EEPROM Serial ID
Name of Field
Vendor Name
Vendor OUI
Vendor PN
LUMINENTOIC.COM
Description of Field
SFP Vendor name(ASCII)
IEEE vendor OUI code for LuminentOIC
Inc.
Part number in ASCII, e.g.
SP-12-LR1-CNA
Address
Hex
ASCII
20
4C
L
21
55
U
22
4D
M
23
49
I
24
4E
N
25
45
E
26
4E
N
27
54
T
28
4F
O
29
49
I
30
43
C
37
00
38
06
39
B5
40
53
41
50
P
42
31
1
43
32
2
44
4C
L
45
52
R
46
31
1
47
43
C
48
4E
N
49
41
A
S
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS1501-Oct3105
Rev A.0
622 Mbps SFP Transceiver
SP-12-LR1
Pinout Definitions
Pin
Function
Notes
1
VeeT
TX Ground
2
TX_FAULT
Open Collector
3
TX_DISABLE
Internally Pulled High
4
MOD_DEF2
Serial Data Input
5
MOD_DEF1
Serial Clock Input
6
MOD_DEF0
Internally Grounded
7
NC
Not Connected
8
LOS
Open Collector
9
VeeR
RX Ground
10
VeeR
RX Ground
11
VeeR
RX Ground
12
RXD-
RX Data Negative
13
RXD+
RX Data Positive
14
VeeR
RX Ground
15
VccR
RX Power
16
VccT
TX Power
17
VeeT
TX Ground
18
TXD+
TX Data Positive
19
TXD-
TX Data Negative
20
VeeT
TX Ground
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS1501-Oct3105
Rev A.0
622 Mbps SFP Transceiver
SP-12-LR1
Suggested Transceiver Interface
1�H
Vcc
10�F
1�H
0.1�F
VCCT
.01�F
Protocol IC
R1
LuminentOIC
SFP
10K�
TX_DISABLE
TX_DISABLE
TX_FAULT
TX_FAULT
TD +
SerDes
Laser Driver
.01�F
100�
TD VEET
.01�F
VCCR
10�F
0.1�F
RD +
Receiver Amplifier
.01�F
100�
RD -
RX_LOS
RX_LOS
Vcc
R
VEER
1
R1
R1
.01�F
EEPROM
R1
MOD_DEF 2
MOD_DEF 1
MOD_DEF 0
R1=4.7K to 10K�
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS1501-Oct3105
Rev A.0
622 Mbps SFP Transceiver
SP-12-LR1
Outline drawing
Units in mm
Section A-A
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS1501-Oct3105
Rev A.0
622 Mbps SFP Transceiver
SP-12-LR1
Ordering Information
Available Options: SP-12-LR1-CNA
SP-12-LR1-CDA
SP-12-LR1-RNA
SP-12-LR1-RDA
SP-12-LR1-TNA
SP-12-LR1-TDA
Part numbering Definition:
SP - 12 - LR1 - Temperature Diagnostic
Revision
• SP = Small Form Pluggable
12 = OC12, 622 Mbps
LR1 = Long Reach 40 km
• Operating Temperature
C = Commercial (-5 to 70ºC)
R = Reduced (-20 to 85ºC)
T = Industrial (-40 to 85ºC)
• D = Digital Diagnostic
N = No Digital Diagnostic
• Design Revision
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS1501-Oct3105
Rev A.0