KPBC1005 THRU KPBC110 AND BR305 THRU BR310 SILICON BRIDGE RECTIFIERS Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes BR-3 FEATURES The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Ideal for printed circuit boards Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260 C/10 seconds,at 5 lbs. (2.3kg) tension 0.213(5.4) 0.193(4.9) 0.750 (19.1) 0.035(0.9) DIA. 0.028(0.7) TYP. 0.620(15.7) 0.580(14.7) MIN. HOLE FOR NO.6 SCREW MECHANICAL DATA 0.445(11.3) 0.405(10.3) AC 0.445(11.3) 0.405(10.3) Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting: Thru hole for #6 screw,5in.-lbs. torque max. Weight:0.093 ounce, 2.62 grams 0.620(15.7) 0.580(14.7) AC Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load, for current capacitive load derate by 20%. SYMBOLS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward TA=50 C(Note 2) output rectified current at TA=25 C(Note 3) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Rating for Fusing(t<8.3ms) Maximum instantaneous forward voltage drop per birdge element at 1.5A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating junction temperature range storage temperature range VRRM VRMS VDC KPBC 1005 BR305 50 35 50 KPBC 101 BR31 100 70 100 KPBC 102 BR32 200 140 200 I(AV) KPBC 104 BR34 KPBC 106 BR36 400 280 400 3.0 2.0 600 420 600 KPBC 108 BR38 800 560 800 KPBC 110 BR310 UNITS 1000 700 1000 VOLTS VOLTS VOLTS Amps IFSM 60 Amps I2t 15 1.0 A2s VF IR CJ RqJA TJ TSTG 10 0.5 20 12 -55 to +125 -55 to +150 NOTES: 1.Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on 4.0” x 4.0” x0.11” thick(10.5x10.5x0.3cm)Al.plate. 3.Unit mounted on P.C. board with 0.5” x 0.5”(12x12mm) copper pads,0.375”(9.5mm) lead length. www.shunyegroup.com Volts uA mA pF C/W C C RATINGS AND CHARACTERISTIC CURVES KPBC1005 THRU KPBC110 AND BR305 THRU BR310 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE 2.5 2.0 Single Phase Half Wave 60Hz Resistive or inductive Load 1.5 1.0 5 0 25 50 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 60 £PEAK FORWARD SURGE CURRENT, AMPERES 3.0 75 100 125 150 50 40 30 20 175 10 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 AMBIENT TEMPERATURE, C FIG. 4-TYPICAL REVERSE CHARACTERISTICS FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1,000 10 1 TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE 0.1 0.01 0.6 0.8 1.0 1.2 1.4 1.5 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 20 100 10 TJ=100 C 1 TJ=25 C 0.1 0.01 INSTANTANEOUS FORWARD VOLEAGE, VOLTS 0 20 40 60 80 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/W FIG. 5-TYPICAL JUNCTION CAPACITANCE 100 10 TJ=25 C 100 10 1 0.1 0.01 0.1 1 10 1 0.1 1.0 10 100 PERCENT OF PEAK REVERSE VOLTAGE,% 200 JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz 100 REVERSE VOLTAGE,VOLTS www.shunyegroup.com t,PULSE DURATION,sec. 100