ZMM5225B - ZMM5267B ZENER DIODES VZ : 3.0 to 75V PD : 500mW MiniMELF (SOD-80C) Cathode Mark φ 0.063 (1.64) FEATURES : 0.055 (1.40) • Silicon planar zener diodes • Standard Zener voltage tolerance is ±5% • Other tolerances are available upon request. • These diodes are also available in the DO-35 case with the type designation 1N5225B … 1N5267B, • Pb / RoHS Free 0.019(0.48) 0.011(0.28) 0.142(3.6) 0.134(3.4) Mounting Pad Layout 0.098 (2.50) Max. MECHANICAL DATA : 0.049 (1.25)Min. * Case : MiniMELF Glass Case (SOD-80C) * Weight : 0.05 gram (approximately) 0.079 (2.00)Min. 0.197 (5.00) REF Dimensions in inches and ( millimeters ) Maximum Ratings and Thermal Characteristics Rating at 25 °C ambient temperature unless otherwise specifie. Parameter Symbol Value Unit VF 1.25 V Zener Current see Table "Characteristics" Maximum Forward Voltage at I F = 200 mA. Power Dissipation at Tflange = 75°C Thermal Resistance Junction to Ambient Air PD RθJA (1) mW (1) °C/W 500 300 Junction temperature TJ 175 °C Storage temperature range TS -65 to + 150 °C Note: (1) Valid provided that electrodes are kept at ambient temperature Page 1 of 2 Rev. 02 : March 25, 2005 ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specifie Nominal Zener Test (3) Current Voltage Type ZMM5225B ZMM5226B ZMM5227B ZMM5228B ZMM5229B ZMM5230B ZMM5231B ZMM5232B ZMM5233B ZMM5234B ZMM5235B ZMM5236B ZMM5237B ZMM5238B ZMM5239B ZMM5240B ZMM5241B ZMM5242B ZMM5243B ZMM5244B ZMM5245B ZMM5246B ZMM5247B ZMM5248B ZMM5249B ZMM5250B ZMM5251B ZMM5252B ZMM5253B ZMM5254B ZMM5255B ZMM5256B ZMM5257B ZMM5258B ZMM5259B ZMM5260B ZMM5261B ZMM5262B ZMM5263B ZMM5264B ZMM5265B ZMM5266B ZMM5267B VZ @ I ZT IZT (V) (mA) 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.0 6.2 6.8 7.5 8.2 8.7 9.1 10 11 12 13 14 15 16 17 18 19 20 22 24 25 27 28 30 33 36 39 43 47 51 56 60 62 68 75 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 9.5 9.0 8.5 7.8 7.4 7.0 6.6 6.2 5.6 5.2 5 4.6 4.5 4.2 3.8 3.4 3.2 3.0 2.7 2.5 2.2 2.1 2.0 1.8 1.7 Maximum Zener Impedance (1) ZZK @ ZZT @ I ZT IZK = 0.25mA (Ω) (Ω) 29 28 24 23 22 19 17 11 7 7 5 6 8 8 10 17 22 30 13 15 16 17 19 21 23 25 29 33 35 41 44 49 58 70 80 93 105 125 150 170 185 230 270 1600 1600 1700 1900 2000 1900 1600 1600 1600 1000 750 500 500 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 600 700 700 800 900 1000 1100 1300 1400 1400 1600 1700 Maximum Reverse Leakage Current IR @ V R (μA) (V) 50 25 15 10 5.0 5.0 5.0 5.0 5.0 5.0 3.0 3.0 3.0 3.0 3.0 3.0 2.0 1.0 0.5 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 1.0 1.0 1.0 1.0 1.0 2.0 2.0 3.0 3.5 4.0 5.0 6.0 6.5 6.5 7.0 7.0 8.4 9.1 9.9 10.0 11 12 13 14 14 15 17 18 19 21 21 23 25 27 30 33 36 39 43 46 47 52 56 Typical Temperature Coefficient αVZ(%/ °C) Maximum Regulator Current(2) IZM (mA) -0.075 -0.070 -0.065 -0.060 -0.055 ±0.030 ±0.030 +0.038 +0.038 +0.045 +0.050 +0.058 +0.062 +0.065 +0.068 +0.075 +0.076 +0.077 +0.079 +0.082 +0.082 +0.083 +0.084 +0.085 +0.086 +0.086 +0.087 +0.088 +0.089 +0.090 +0.091 +0.091 +0.092 +0.093 +0.094 +0.095 +0.095 +0.096 +0.096 +0.097 +0.098 +0.097 +0.098 152 138 126 115 106 97 89 81 76 73 67 61 55 52 50 45 41 38 35 32 30 28 27 25 24 23 21 19.1 18.2 16.8 16.2 15.1 13.8 12.6 11.6 10.6 9.7 8.9 - Notes : (1) The Zener impedance is derived from the 1kHz AC voltage which results when an AC current having an RMS value equal to 10% of the Zener current (I ZT or IZK) is superimposed on IZT or IZK. Zener impedance is measured at two points to insure a sharp knee on the breakdown curve and to eliminate unstable units (2) Valid provided that electrodes are kept at ambient temperature (3) Standard Zener voltage tolerance is ± 5% tolerance. Page 2 of 2 Rev. 02 : March 25, 2005