TAIYO-YUDEN NRH2410T6R8MN

Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2009. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called“TAIYO YUDEN’
s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
Should you have any question or inquiry on this matter, please contact our sales staff.
1
notice_e-01
SMD INDUCTORS SMALL AND LARGE CURRENT TYPE
REFLOW
■ FEATURES
■ APPLICATIONS
◦Small and Low profile inductor.
◦For small DC/DC converter
(cellular Phone, HDD, DVC, DSC, PDA, LCD display etc).
◦It corresponds to High current.
◦Simple and original magnetic shield structure.
◦Durable structure against dropping impact.
■ ORDERING CODE
N
R
H
2
4
❶
1
T △ 1
0
❷
❶Type
NRH
NRS Coating resin specification
NRV
❸
❷External dimensions
（W×L×H）
T△
M ○ ○ ○
0
❹
❸Packaging
Tape & Reel
example
2410
3010
3012
5012
5014
5020
6010
0
❺
❺Inductance tolerance
M
±20%
N
±30%
❹Nominal inductance
〔μH〕
example
△＝Blank Space
2.4×2.4×1.0mm
3.0×3.0×1.0mm
3.0×3.0×1.2mm
5.0×5.0×1.2mm
5.0×5.0×1.4mm
5.0×5.0×2.0mm
6.0×6.0×1.0mm
2R2
100
101
❻
2.2
10
100
❻Internal code
○○○ Standard products
○＝Blank Space
※R＝decimal point
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
Δℓ
H
L
H
L
Δe
e
e
W
f
f
W
e
Type
L
W
H
e
f
e
Standard
Quantity [pcs]
Tape & Reel
Type
2500
NRS5012
2000
NRS5014
2000
NRS5020
2.4±0.1
2.4±0.1
1.0 max
0.6±0.2
1.45±0.2
（0.095±0.004）（0.095±0.004）（0.039 max）（0.024±0.008）（0.057±0.008）
1.0 max
NRH3010
3.0±0.1 （0.039 max） 0.9±0.2
1.9±0.2
3.0±0.1
NRH3012 （0.118±0.004） （0.118±0.004） 1.2 max （0.035±0.008）（0.075±0.008）
NRV3012
（0.047 max）
NRH2410
Unit：mm
（inch）
NRS6010
L
W
H
Δe
Δe
e
Δℓ
f
1.2 max
（0.047 max）
4.9±0.2
4.9±0.2
1.4 max
1.2±0.2
0.3±0.2
3.3±0.2
1.3±0.3
（0.193±0.008） （0.193±0.008） （0.055 max） （0.047±0.008） （0.011±0.008） （0.130±0.008） （0.051±0.011）
2.0 max
（0.079 max）
0.3±0.2
4.0±0.2
2.3±0.3
6.0±0.2
6.0±0.2
1.0 max
1.35±0.2
（0.236±0.008）（0.236±0.008） （0.039 max） （0.053±0.008） （0.011±0.008） （0.157±0.008） （0.091±0.011）
Recommended Land Patterns
【NRH2410】
【NRS5012, NRS5014, NRS5020】
800
1000
4.7
2.7
4.0
0.7
1000
【NRS6010】
3.6
2.2
2.0
0.7
1000
Unit：mm
（inch）
【NR3010, NRH3012, NRV3012】
1.45
Standard
Quantity [pcs]
Tape & Reel
0.8
5.7
0.8
1.5
1.5
1.6
1.6
■ AVAILABLE INDUCTANCE RANGE
Range
Type
NRH2410
Inductance［μH］
Imax
[mA]
1.0
1410
2.2
4.7
10
22
450
300
NRH3010
NRH3012
Rdc±20％ Imax
［Ω］[mA]
Rdc±20％ Imax
［Ω］[mA]
0.070 1480
0.065 1710
NRV3012
Rdc±20％ Imax
［Ω］[mA]
0.048
0.350 720
0.770
0.270
500
0.630
NRS5014
Rdc±20％ Imax
［Ω］[mA]
2300
1100
0.690 600
1.47 380
NRS5012
Rdc±20％ Imax
［Ω］[mA]
NRS5020
Rdc±20％ Imax
［Ω］[mA]
3600
0.053
2800
0.045
1800
0.100
NRS6010
Rdc±20％ Imax
［Ω］[mA]
Rdc±20％
［Ω］
0.021
1900
0.090
1300
0.120 1000
0.270
900
0.260
0.120
850
0.420
100
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
128
1
wound05_e-01
■ PART NUMBERS
●NRH 2410 Shielded type
Ordering code
NRH2410T
NRH2410T
NRH2410T
NRH2410T
NRH2410T
NRH2410T
NRH2410T
NRH2410T
NRH2410T
NRH2410T
R68NN 4
1R0NN 4
1R5MN
2R2MN
3R3MN
4R7MN
6R8MN
100MN
150MN
220MN
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20%)
120
106
94
77
56
50
43
32
27
22
0.060
0.070
0.110
0.150
0.220
0.290
0.410
0.690
1.02
1.47
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20%)
120
99
86
64
50
44
34
25
22
0.065
0.075
0.083
0.130
0.170
0.250
0.350
0.550
0.770
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20％)
111
95
78
61
50
43
32
26
22
0.048
0.055
0.075
0.100
0.130
0.190
0.270
0.450
0.630
Inductance
Tolerance
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20％)
2.2
±20％
70
0.120
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
Inductance
Tolerance
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20％)
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
1.0
1.5
2.2
3.3
4.7
6.8
10
100
86
70
48
40
36
26
0.053
0.070
0.085
0.160
0.180
0.260
0.420
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20％)
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
1.2
1.5
2.2
3.3
4.7
6.8
10
15
22
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
RoHS
Inductance
Tolerance
±30％
±20％
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
2,200
1,570
1,800
1,410
1,550
1,160
1,290
970
1,000
770
880
670
750
570
550
450
470
370
390
300
Measuring
frequency
〔kHz〕
100
●NRH 3010 Type
NRH3010T
NRH3010T
NRH3010T
NRH3010T
NRH3010T
NRH3010T
NRH3010T
NRH3010T
NRH3010T
1R2N
1R5N
2R2M
3R3M
4R7M
6R8M
100M
150M
220M
Inductance
Tolerance
±30％
±20％
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
1,700
1,480
1,440
1,370
1,300
1,300
1,000
1,030
850
900
700
745
600
620
450
480
380
410
Measuring
frequency
〔kHz〕
100
FERRITE PRODUCTS
Ordering code
●NRH 3012 Type
Ordering code
NRH3012T
NRH3012T
NRH3012T
NRH3012T
NRH3012T
NRH3012T
NRH3012T
NRH3012T
NRH3012T
1R0N
1R5N
2R2M
3R3M
4R7M
6R8M
100M
150M
220M
Inductance
Tolerance
±30％
±20％
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
2,200
1,710
1,700
1,600
1,500
1,370
1,200
1,210
1,000
1,060
850
890
730
720
530
570
500
500
Measuring
frequency
〔kHz〕
100
●NRV 3012 Type
Ordering code
NRV3012T 2R2M
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
1,800
1,100
Measuring
frequency
〔kHz〕
100
●NRS 5012 Type
Ordering code
NRS5012T
NRS5012T
NRS5012T
NRS5012T
NRS5012T
NRS5012T
NRS5012T
1R0N
1R5N
2R2M
3R3M
4R7M
6R8M
100M
±30％
±20％
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
4,500
2,300
3,800
2,200
3,100
2,000
2,400
1,450
2,200
1,400
1,700
1,100
1,400
850
Measuring
frequency
〔kHz〕
100
●NRS 5014 Type
Ordering code
NRS5014T 1R2N
NRS5014T 2R2N
NRS5014T 3R3N
NRS5014T 4R7N
RoHS
RoHS
RoHS
RoHS
Inductance
Tolerance
1.2
2.2
3.3
4.7
±30％
86
56
48
41
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
0.045
3,800
2,800
0.065
2,800
2,300
0.080
0.100
2,350
2,100
2,050
1,800
Measuring
frequency
〔kHz〕
100
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound05_e-01
1
129
■ PART NUMBERS
●NRS 5020 Type
Ordering code
NRS5020T
NRS5020T
NRS5020T
NRS5020T
NRS5020T
NRS5020T
NRS5020T
NRS5020T
NRS5020T
1R0N
1R5N
2R2N
3R3N
4R7M
6R8M
100M
150M
220M
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
EHS (Environmental
Hazardous
Substances)
Inductance
[μH]
Inductance
Tolerance
±30％
±20％
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20％)
81
68
57
46
37
30
24
20
17
0.021
0.026
0.035
0.048
0.060
0.090
0.120
0.165
0.260
Self-resonant
frequency
〔MHz〕(min.)
DC Resistance
[Ω] (±20％)
90
65
50
38
30
25
0.090
0.110
0.135
0.165
0.220
0.270
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
4,000
3,600
3,350
3,200
2,900
2,900
2,400
2,400
2,000
2,000
1,600
1,650
1,300
1,450
1,100
1,200
900
1,000
Measuring
frequency
〔kHz〕
100
●NRS 6010 Type
Ordering code
NRS6010T
NRS6010T
NRS6010T
NRS6010T
NRS6010T
NRS6010T
1R5N
2R2N
3R3N
4R7N
6R8N
100M
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
Tolerance
1.5
2.2
3.3
±30％
4.7
6.8
10
±20％
〔mA〕
Rated current ※）
Saturation
Temperature rise
current
current
Idc1
Idc2
1,900
2,400
1,900
1,700
1,600
1,500
1,300
1,400
1,200
1,200
1,000
1,100
Measuring
frequency
〔kHz〕
100
※）The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃)
※）The temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃)
※）The rated current is the DC current value that satisfies both of current value saturation current value and temperature rise current value.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
130
1
wound05_e-01
■ ELECTRICAL CHARACTERISTICS
■ DC Bias characteristics
（Measured by HP4285A）
NRH 2410
NRH 3010
220M
220M
4R7M
2R2M
1
220M
100M
4R7M
2R2M
1
1R0N
100
10
Inductance
〔μH〕
100M
NRV 3012
100
10
Inductance
〔μH〕
Inductance
〔μH〕
10
NRH 3012
100
10
Inductance
〔μH〕
100
100M
4R7M
2R2M
1
2R2M
1
1R0N
100
1,000
0.1
10
10,000
DC Bias
〔mA〕
100
1,000
0.1
10
10,000
100
DC Bias
〔mA〕
NRS 5012
1,000
0.1
10
10,000
DC Bias
〔mA〕
NRS 5014
100
NRS 5020
100
100
100
10
10
10
1,000
10,000
DC Bias
〔mA〕
NRS 6010
100
2R2M
1
4R7M
1
4R7M
2R2N
1
1R2N
100M
Inductance
〔μH〕
4R7M
10
100M
Inductance
〔μH〕
100M
Inductance
〔μH〕
Inductance
〔μH〕
200M
FERRITE PRODUCTS
0.1
10
4R7M
2R2N
1
1R0N
1R0N
0.1
10
100
1,000
DC Bias
〔mA〕
10,000
0.1
10
100
1,000
10,000
0.1
10
100
DC Bias
〔mA〕
1,000
DC Bias
〔mA〕
10,000
0.1
10
100
1,000
10,000
DC Bias
〔mA〕
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound05_e-01
1
131
■ PACKAGING
①Minimum Quantity
Type
NRH 2410
NR 3010/NRH 3010
NR 3012/NRH3012/NRV3012
NR 3015
NR 4010
NR 4012
NR 4018
NRG4026
NRS5012
NRS5014
NRS5020
NR 5040
NRS6010
NR 6012
NR 6020
NR 6028
NR 6045
NR 8040
Chip cavity
Type
Standard Quantity [pcs]
Tape ＆ Reel
2500
2000
2000
2000
5000
4500
3500
2000
1000
1000
800
1500
1000
1000
2500
2000
1500
1000
A
Insertion pitch
B
Tape thickness
F
T
K
1.4±0.1
（0.055±0.004）
NR 4010
NR 4012
NR 4018
1.6±0.1
（0.063±0.004）
4.3±0.1
4.3±0.1
（0.169±0.004）（0.169±0.004）
2.1±0.1
（0.083±0.004）
0.3±0.05
3.1±0.1
（0.012±0.002）（0.122±0.004）
NRG 4026
1.4±0.1
（0.055±0.004）
1.6±0.1
（0.063±0.004）
2.3±0.1
（0.091±0.004）
4.2±0.1
（0.165±0.004）
1.4±0.1
（0.055±0.004）
1.6±0.1
（0.063±0.004）
NRS 5012
NRS 5014
5.25±0.1
5.25±0.1
（0.207±0.004）（0.207±0.004）
8.0±0.1
（0.315±0.004）
5.15±0.1
5.15±0.1
NR 5040
（0.203±0.004）（0.203±0.004）
NRS 5020
NRS 6010
NR 6012
NR 6020
②Tape Material
0.4±0.1
（0.016±0.004） 2.3±0.1
（0.090±0.004）
6.3±0.1
6.3±0.1
（0.248±0.004）（0.248±0.004）
NR 6028
3.1±0.1
（0.122±0.004）
NR 6045
4.7±0.1
（0.185±0.004）
Unit : mm (inch)
◦Embossed tape 16mm wide (0.63 inches wide)
F
CHIP cavity
K
1.75±0.1
（0.069±0.004）
16.0±0.3
（0.630±0.012）
φ1.5±0.1
（0.059±0.004）
T
B
2.0±0.1
（0.079±0.004）
4.0±0.1
（0.157±0.004）
7.5±0.1
（0.295±0.004）
A
Electrode
（bottom view）
③Taping dimensions
◦Embossed tape 8mm wide (0.315 inches wide)
＋0.004
1.75±0.1
K
（0.069±0.004）
T
3.5±0.1
（0.138±0.004）
）
B
A
NR 8040
A
B
Insertion pitch
F
8.3±0.1
12.0±0.1
8.3±0.1
(0.327±0.004) (0.327±0.004) (0.472±0.004)
Tape thickness
T
K
0.5±0.1
(0.020±0.004)
4.5±0.1
(0.177±0.004)
Unit : mm (inch)
8.0±0.2
（0.315±0.008）
CHIP cavity
＋0.1
φ1.5ー0
（0.059ー0
Chip cavity
Type
④Leader and Blank portion
◦NR, NRH, NRS, NRG, NRV
Electrode
（bottom view）
F
Chip cavity
Blank portions
Blank portions
Leader
2.0±0.05
4.0±0.1
（0.079±0.002） （0.157±0.004）
Chip cavity
Type
NRH 2410
A
Insertion pitch
F
B
2.6±0.1
2.6±0.1
（0.102±0.004）（0.102±0.004）
Tape thickness
T
K
0.25±0.05
1.3±0.1
（0.009±0.002）（0.051±0.004）
160mm or more
(6.3 inches or more)
1.4±0.1
（0.055±0.004）
4.0±0.1
NR 3012
3.2±0.1
3.2±0.1 （0.157±0.004） 0.3±0.05
1.6±0.1
NRH 3012
（0.126±0.004）（0.126±0.004）
（0.012±0.002）（0.063±0.004）
NRV3012
100mm or more
(3.94 inches or more)
NR 3010
NRH 3010
400mm or more
(15.8 inches or more)
Direction of tape feed
1.9±0.1
（0.075±0.004）
NR 3015
Unit : mm (inch)
◦Embossed tape 12mm wide (0.47 inches wide)
1.75±0.1
K
（0.069±0.004）
T
B
A
F
12.0±0.3
（0.472±0.012）
CHIP cavity
5.5±0.1
（0.217±0.004）
＋0.1
φ1.5ー0
＋0.004
（0.059ー0
）
Electrode
（bottom view）
2.0±0.1
4.0±0.1
（0.079±0.004） （0.157±0.004）
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0405_pack-P1
1
wound0405_pack_e-01
■ PACKAGING
⑤Reel size
W
φD
φd
2±0.5
φ13±0.5
2.5 or less
（0.098inches
or less）
φD
Reel size (Reference values)
φd
W
180±0.5
（7.087±0.019）
60±1.0
（2.36±0.04）
10.0±1.5
（0.394±0.059）
180±3.0
（7.087±0.118）
60±2.0
（2.36±0.08）
14.0±1.5
（0.551±0.059）
Type
NRH2410
NR 3010
NRH 3010
NR 3012
NRH 3012
NRV 3012
NR 3015
NRS 5012
NRS 5014
NRS 5020
NRS 6010
NR 6012
Unit : mm (inch)
W
φD
φd
2±0.5
φ13±0.5
t
Type
φD
Reel size (Reference values)
φd
t (max.)
W
NR 4010
NR 4012
NR 4018
NRG 4026
NR 5040
330±3.0
80±2.0
（12.99±0.118） （3.15±0.078）
NR 6020
NR 6028
NR 6045
18.5
（0.72）
13.5±1.0
（0.531±0.04）
NR 8040
22.5
（0.89）
17.5±1.0
（0.689±0.04）
Unit : mm (inch)
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as
illustrated below.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0405_pack_e-01
1
wound0405_pack-P2
■ RELIABILITY DATA
1. Operating Temperature Range
BRC1608, BRL2012, BRC2016, BRC2518,
ー25∼＋105℃
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
ー25∼＋120℃
NRH24/30, NRS50/60 Type
NR10050 Type
ー25∼＋105℃
【Test Method and Remarks】
Including self-generated heat
2. Storage Temperature Range
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
ー40∼＋85℃
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : 0 to 40℃ for the product with taping.
NR10050 Type : 0∼40℃ for the product with taping.
3. Rated current
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
Within the specified tolerance
NRH24/30, NRS50/60 Type
NR10050 Type
4. Inductance
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
Within the specified tolerance
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : LCR Meter : HP 4285A or equivalent, Measuring frequency : Specified frequency
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : LCR Meter : HP 4285A or equivalent, 100KHz, 1V
NR10050 Type
: LCR Meter : HP 4263A or equivalent, 100KHz, 1V
5. DC Resistance
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
Within the specified tolerance
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
DC ohmmeter : HIOKI 3227 or equivalent
6. Self resonance frequency
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
Within the specification
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type :
Inpedance analyzer/material analyzer : HP4291A or equivalent HP4191A, 4192A or equivalent
7. Temperature characteristic
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
BRL2012, BRC2016, BRL2518, BRL3225, BRC2518, BRFL2518
Inductance change : Within ±15%
BRC1608
Inductance change : Within ±20%
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
Inductance change : Within ±20%
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type :
Measurement of inductance shall be taken at temperature range within −25℃∼＋85℃.
With reference to inductance value at ＋20℃., change rate shall be calculated.
Change of maximum inductance deviation in step 1 to 5
Temperature at step 1
Temperature at step 2
Temperature at step 3
Temperature at step 4
Temperature at step 5
20℃
Minimum operating temperature
20℃ (Standard temperature)
Maximum oparating temperature
20℃
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0407_reli-RP1
1
wound0407_reli_e-01
■ RELIABILITY DATA
8. Resistance to flexure of substrate
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
No damage.
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type :
The test samples shall be soldered to the test board by the reflow. As illustrated below, apply force in the direction of the arrow indicating until deflection of the test board
reaches to 2 mm.
Force Rod
20
10
Test board size
: 100×40×1.0
R230
Test board material
: glass epoxy-resin
Solder cream thickness : 0.12 (BR Series)
Board
0.10 (NR30/40, NRV30, NRH24/30,NRG40)
Test Sample
R5
0.15 (NR50/60/80, NRS50/60)
45±2mm
Land dimension
（BRC1608）
Land dimension
（BRL2012）
0.9
Land dimension
（BRL3225）
1.4
0.55 0.8 0.55
0.65 0.9 0.65
Land dimension
（ＢＲＣ2016）
Land dimension
（NR30, NRH30, NRV30）
2.7
1.0
1.6
Land dimension
（BRL2518,BRC2518,BRFL2518） Land dimension
（NRH24）
1.95
1.8
0.7 0.8 0.7
0.65 1.5 0.65
4.0
1.5 2.1 1.5
1.6 3.1 1.6
Land dimension
（NR40, NRG40）
Land dimension
（NR80）
3.7
2.0
0.7 0.75 0.7
Land dimension
（NR, NRS50）
5.7
2.7
0.8 1.4 0.8
1.0
45±2mm
Land dimension
（NR60, NRS60）
1.2 1.6 1.2
7.5
1.8 3.8 1.8
Printed board thickness : 1.0mm
Unit : mm
9. Insulation resistance : between wires
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
NR10050 Type
10. Insulation resistance : between wire and core
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
NR10050 Type
11. Withstanding voltage : between wires and core
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
NR10050 Type
12. Adhesion of terminal electrode
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
Shall not come off PC board.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type :
The test samples shall be soldered to the test board by the reflow.
・Applied force
: 10N to X and Y directions.
・Duration
: 5s.
10N, 5s
・Solder cream thickness : 0.15mm.
BRC1608, NR10050 Type :
・Applied force : 5N to X and Y directions.
・Duration
: 5s.
13. Resistance to vibration
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
Inductance change : Within ±10%
NR30/40/50/60/80, NRV30, NRG40,
No significant abnormality in appearance.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type :
The test samples shall be soldered to the test board by the reflow.
Then it shall be submitted to below test conditions.
Frequency Range
Total Amplitude
Sweeping Method
Time
10∼55Hz
1.5mm (May not exceed acceleration 196m/s2)
10Hz to 55Hz to 10Hz for 1min.
X
Y
For 2 hours on each X, Y, and Z axis.
Z
Recovery : At least 2hrs of recovery under the standard condition sfter the test, followed by the measurement within 48hrs.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0407_reli_e-01
1
wound0407_reli-RP2
■ RELIABILITY DATA
14. Solderability
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
At least 90％ of surface of terminal electrode is covered by new solder.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050Type :
The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table.
Flux : Methanol solution containing rosin 25%.
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type :
Solder Temperature
Time
245±5℃
5±1.0 sec.
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type :
Solder Temperature
Time
245±5℃
5±0.5 sec.
※Immersion depth : All sides of mounting terminal shall be immersed.
15. Resistance to soldering heat
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
Inductance change : Within ±10%
NR30/40/50/60/80, NRV30, NRG40,
No significant abnormality in appearance.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type :
3 times of reflow oven at 230℃ MIN. for 40sec. with peak temperature at 260＋0
ー5 ℃ for 5sec.
:
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type
The test sample shall be exposed to reflow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times.
NR6020 Type :
The test sample shall be exposed to reflow oven at 230±5℃ for 40 seconds, with peak temperature at 250＋0
ー5 ℃ for 5 seconds, 2 times.
Test board thickness : 1.0mm
Test board material : glass epoxy-resin
16. Thermal shock
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
Inductance change : Within ±10%
NR30/40/50/60/80, NRV30, NRG40,
No significant abnormality in appearance.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type :
The test samples shall be soldered to the test board by the reflow. The test samples shall be placed at specified temperature for specified time by step 1 to step 4 as shown
in below table in sequence. The temperature cycle shall be repeated 100 cycles.
Step
Conditions of 1 cycle
Temperature (℃)
Duration (min)
1
2
ー40±3
Room temperature
30±3
Within 3
3
4
＋85±2
Room temperature
30±3
Within 3
17. Damp heat
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
Inductance change : Within ±10%
No significant abnormality in appearance.
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type :
Temperature
Humidity
Time
60±2℃
90∼95%RH
1000 hours.
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type :
The test samples shall be soldered to the test board by the reflow.
The test samples shall be placed in thermostatic oven set at specified temperature and humidity as shown in below table.
Temperature
Humidity
Time
60±2℃
90∼95%RH
500±24hour
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0407_reli-RP3
1
wound0407_reli_e-01
■ RELIABILITY DATA
18. Loading under damp heat
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
Inductance change : Within ±10%
NR30/40/50/60/80, NRV30, NRG40,
No significant abnormality in appearance.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type :
Temperature
Humidity
Applied current
Time
60±2℃
90∼95％RH
Rated current
1000hours.
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type :
The test samples shall be soldered to the test board by the reflow.
The test samples shall be placed in thermostatic oven set at specified temperature and humidity and applied the rated current continuously as shown in below table.
Temperature
Humidity
Applied current
Time
60±2℃
90∼95％RH
Rated current
500±2hour
19. Low temperature life test
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
Inductance change : Within ±10%
NR30/40/50/60/80, NRV30, NRG40,
No significant abnormality in appearance.
NRH24/30, NRS50/60 Type
NR10050 Type
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type :
Temperature
Duration
ー40±2℃
1000hours
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type :
The test samples shall be soldered to the test board by the reflow.
After that, the test samples shall be placed at test conditions as shown in below table.
Temperature
Time
−40±3℃
500±24hour
20. High temperature life test
BRC1608, BRL2012, BRC2016, BRC2518, Inductance change : Within ±10%
BRFL2518, BRL2518, BRL3225 Type
No significant abnormality in appearance.
NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
Inductance change : Within ±10%
NR10050 Type
No significant abnormality in appearance.
【Test Method and Remarks】
BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type :
Temperature
Duration
85±2℃
1000hours
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
NR10050 Type :
Temperature
Time
105±3℃
500±24hour
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
21. Loading at high temperature life test
BRC1608, BRL2012, BRC2016, BRC2518,
BRFL2518, BRL2518, BRL3225 Type
NR30/40/50/60/80, NRV30, NRG40,
Inductance change : Within ±10%
NRH24/30, NRS50/60 Type
No significant abnormality in appearance.
NR10050 Type
【Test Method and Remarks】
NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type :
The test samples shall be soldered to the test board by the reflow soldering.
Temperature
Applied current
Time
85±2℃
Rated current
500±24hour
22. Standard condition
BRC1608, BRL2012, BRC2016, BRC2518, Standard test condition :
BRFL2518, BRL2518, BRL3225 Type
Unless otherwise specified, temperature is 20±15％ and 65±20％of relative humidity.
When there are question concerning measurement result : In order to provide correlation date, the test shall be condition of 20±2℃
NR30/40/50/60/80, NRV30, NRG40,
of temperature, 65±5% relative humidity.
NRH24/30, NRS50/60 Type
Inductance is in accordance with our measured value.
NR10050 Type
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0407_reli_e-01
1
wound0407_reli-RP4
■ PRECAUTIONS
SMD Inductors
1. Circuit Design
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
Precautions
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
◆Land pattern design
1. Please refer to a recommended land pattern.
◆Land pattern design
Technical
Surface Mounting
consider・Mounting and soldering conditions should be checked beforehand.
ations
・Applicable soldering process to this products is reflow soldering only.
Precautions
3. Considerations for automatic placement
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
Precautions
2. Mounting and soldering conditions should be checked beforehand.
Technical
◆Adjustment of mounting machine
consider1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
ations
4. Soldering
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
2. This products is reflow soldering only.
3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, soldering etc
Precautions
sufficiently.
◆Recommended conditions for using a soldering iron (NR10050 Type)
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
300
200
100
0
150∼180
90±30sec
5sec max
Peak：
260＋0/ー5℃
30±10sec
230℃ min
Ｈeating Time【sec】
5sec max
300
200
100
0
Peak：
250＋5/ー0℃
150∼180
90±30sec
30±10sec
230℃ min
Ｈeating Time【sec】
・NR10050 Type
Recommended reflow condition (Pb free solder)
Temperature
［℃］
Temperature
［℃］
Technical
considerations
・NR30/40/50/60/80, NRV30, NRG40,
NRH24/30, NRS50/60 Type
Recommended reflow condition (Pb free solder)
Temperature
［℃］
・BRC1608, BRL2012, BRL2518,
BRC2016, BRL3225 Type BRC2518, BRFL2518
Recommended reflow condition (Pb free solder)
5sec max
300
200
100
0
Peak：
250＋0/ー5℃
150∼180
90±30sec
30±10sec
230℃ min
Ｈeating Time【sec】
5. Cleaning
Precautions
Technical
considerations
◆Cleaning conditions
1. Washing by supersonic waves shall be avoided.
◆Cleaning conditions
1. If washing by supersonic waves, supersonic waves may cause broken products.
6. Handling
◆Handling
1. Keep the product away from all magnets and magnetic objects.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
Precautions
1. Please do not give the product any excessive mechanical shocks.
2. Please do not add any shock and power to a product in transportation.
◆Pick-up pressure
1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part.。
◆Packing
1. Please avoid accumulation of a packing box as much as possible.
◆Breakaway PC boards (splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
Technical
2. There is a case to be broken by the handling in transportation.
considerations
◆Pick-up pressure
1. Damage and a characteristic can vary with an excessive shock or stress.
◆Packing
1. There is a case that transformation and a product of tape are damaged by accumulation of a packing box.
7. Storage conditions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
・Recommended conditions
Ambient temperature : 0∼40℃
Humidity
: Below 70% RH
Precautions
Technical
considerations
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, product should be used within 6 months from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0407_reli-RP5
1
wound0407_reli_e-01