7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Features Description Serial-ATA is designed as a successor to the • RoHS compliant legacy SATA standard. The new standard is • Fully compatible with devices and OS that support the SATA 1.0a 1.5Gbps standard dedicated to achieve higher transfer rate with thinner cables and more reliable operation than Parallel ATA interface. SATA Flash Modules is perfect replacement storage device for PCs, Laptops, gaming systems, and handheld devices. • 7 pin female SATA connector with latch • Connect to motherboard directly without cable • Non-volatile Flash Memory for outstanding data retention • Placement The on-chip hardware 13/24 bit BCH-ECC engines can correct up to 24 bit errors per 1,024 byte data. • Support global wear-leveling algorithm which ensures maximum lifespan. • Supports Ultra DMA Mode 0 to 5 Multiword DMA mode 0 to 2 PIO Mode 0 to 4 • Supports ATA Security Commands • Support S.M.A.R.T function (self-definition) • Mechanical write-protect switch • Low Power Consumption • Power Supply: 3.3V ± 5%(UDMA mode 5) / 5.0V ± 10%(UDMA mode 4 or lower) • Shock resistance Dimensions Side Millimeters Inches A 40.0 ± 0.3 1.57 ± 0.012 B 30.0 ± 0.2 1.18 ± 0.008 C* 24.3 ± 0.5 0.96 ± 0.020 * Please refer to Mechanical Drawing Transcend Information Inc. 1 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Specifications Physical Specification Form Factor SATA Flash Module Horizontal Type Storage Capacities 128M~8GB Dimensions (mm) Length 40.0 ± 0.3 Width 30.0 ± 0.2 (Not including Write-Protect Switch and SATA connector) Height 24.3 ± 0.5 (refer to mechanical drawing) Input Voltage 5V ± 10% / 3.3V ± 5% Weight 8g Signal: SATA 7 pins female connector with latch Connector Power: 2P 1.5mm pitch wafer connector Environmental Specifications ℃ to 70 ℃ - 40 ℃ to 85 ℃ 0 Operating Temperature Storage Temperature Power Consumption 4GB SATA Flash Modules Power Consumption ℃ (DC 5V @25 ) Transcend Information Inc. Crystal Disk Mark 1.0.6 / 50MB Read 212.2 mA(peak) Write 207.3 mA(peak) Standby 111.8 mA 2 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Reliability 13bit/1K Byte BCH ECC(2k+64 / 4k+128 byte per page flash) Data Reliability 24bit/1K Byte BCH ECC(4k+208 byte per page flash) Data Retention 10 years Connector Durability 500 mating cycles Performance* Model P/N Read (KB/s) Write (KB/s) Random Read (KB/s) Random Write (KB/s) 2GB SATA Flash Module 53696 25491 51174 10518 * Note : The performance is based on Samsung K9F8G08U0M, single channel. Environment: at 25 ℃, tested with ® GA-8IG1000MK, 256 MB RAM, SATA interface support UDMA5, Windows XP Version 2002 SP2, benchmark utility : HDBENCH (version 3.4006), copied file 100MB Actual Capacity Model P/N Capacity C/H/S Capacity User capacity (Bytes) TS512MSDOM7H 512M 971 / 16 / 63 477MB 500,432,896 TS1GSDOM7H 1GB 1966 / 16 / 63 967MB 1,014,333,440 TS2GSDOM7H 2GB 3900 / 16 / 63 1.87GB 2,008,801,280 TS4GSDOM7H 4GB 7785 / 16 / 63 3.73GB 4,009,922,560 TS8GSDOM7H 8GB 15538 / 16 / 63 7.46GB 8,016,560,128 * Note: FAT format for <4GB, FAT32 format for 4~8GB Certification EMC CE, FCC and BSMI (T.B.D) Transcend Information Inc. 3 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Mechanical Drawing B A Bottom View (Normal Type) C Side View (Normal Type) Transcend Information Inc. 4 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules A B Bottom View (Reversed Type) C Side View (Reversed Type) Transcend Information Inc. 5 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Functionality Pin Assignments Pin No. Pin Name 01 GND 02 A+ 03 04 AGND 05 B- 06 07 B+ GND Disk Active Write-Protect Indicator Disabled Transcend Information Inc. 6 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Block Block Diagram SATA 7 PIN Connector Data bus PATA Data bus to SATA Control Signal Flash Memory -CE0, -CE1… D0 – D7 -CE0 ~ -CE3 -WE…-RE Others IDE Bridge D0 ~ D7 Flash Disk Controller D8 ~ D15 2 PIN 3.3V/1.8V 5V/3.3V -CE0, -CE1… Voltage Regulator Flash Memory D0 – D7 -CE0 ~ -CE3 -WE…-RE Flash Memory DC Characteristics Parameter Symbol Min. Max. Unit Supply Voltage VCC 2.97 5.5 V High level output voltage VOH VCC – 0.8 Low level output voltage VOL High level input voltage Low level input voltage Pull up resistance 2 Pull down resistance Transcend Information Inc. VIH Remark V 0.8 V 2.4 V Non-schmitt trigger 2.05 V Schmitt trigger 0.6 V Non-schmitt trigger 1.25 V Schmitt trigger VIL RPU 52.7 141 KOhm RPD 47.5 172 kOhm 1 1 7 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Command Set FR SC SN CY DH LBA E5 or 98h – – – – Y – Support Execute Drive Diagnostic 90h – – – – Y – Support 3 Erase Sector C0h – Y Y Y Y Y Support 4 Flush Cache E7h – – – – Y – Support 5 Format Track 50h – Y – Y Y Y Support 6 Identify Device ECh – – – – Y – Support 7 Idle E3h or 97h – Y – – Y – Support 8 Idle Immediate E1h or 95h – – – – Y – Support 9 Initialize Drive Parameters 91h – Y – – Y – Support 10 NOP 00h – – – – Y – Support 11 Read Buffer E4h – – – – Y – Support 12 Read DMA C8h – Y Y Y Y Y Support 13 Read Multiple C4h – Y Y Y Y Y Support 14 Read Sector(s) 20h or 21h – Y Y Y Y Y Support 15 Read Verify Sector(s) 40h or 41h – Y Y Y Y Y Support 16 Recalibrate 1Xh – – – – Y – Support 17 Request Sense 03h – – – – Y – Support 18 Security Disable Password F6h – – – – Y – Support 19 Security Erase Prepare F3h – – – – Y – Support 20 Security Erase Unit F4h – – – – Y – Support 21 Security Freeze Lock F5h – – – – Y – Support 22 Security Set Password F1h – – – – Y – Support 23 Security Unlock F2h – – – – Y – Support 24 Seek 7Xh – – Y Y Y Y Support 25 Set Feature EFh Y – – – Y – Support 26 Set Multiple Mode C6h – Y – – Y – Support 27 Set Sleep Mode E6h or 99h – – – – Y – Support 28 Standby E2 or 96h – – – – Y – Support 29 Standby Immediate E0 or 94h – – – – Y – Support Command Code 1 Check Power Mode 2 Transcend Information Inc. Status Note 8 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules 30 Translate Sector 87h – Y Y Y Y Y Support 31 Wear Level F5h – – – – Y – Support 32 Write Buffer E8h – – – – Y – Support 33 Write DMA CAh – Y Y Y Y Y Support 34 Write Multiple C5h – Y Y Y Y Y Support 35 Write Multiple w/o Erase CDh – Y Y Y Y Y Support 36 Write Sector(s) 30h or 31h – Y Y Y Y Y Support 37 Write Sector(s) w/o Erase 38h – Y Y Y Y Y Support 38 Write Verify 3Ch – Y Y Y Y Y Support Definitions FR = Features Register SC =Sector Count register (00H to FFH, 00H means 256 sectors) SN = Sector Number register CY = Cylinder Low/High register DH = Head No. (0 to 15) of Drive/Head register LBA = Logic Block Address Mode Support – = Not used for the command Y = Used for the command Transcend Information Inc. 9 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules SMART Command Set SMART Command Set SMART Feature Register Values D0h Read Data D5h Read Log D1h Read Attribute Threshold D6h Write Log D2h Enable/Disable Autosave D8h Enable SMART Operations D3h Save Attribute Values D9h Disable SMART Operations D4h Execute OFF-LINE Immediate DAh Return Status 1. If reserved size is below the Threshold, the status can be read from Cylinder register by Return Status command (DAh). SMART Data Structure BYTE F/V Decription 0-1 X Revision code 2-361 X Vendor specific 362 V Off line data collection status 363 X Self-test execution status byte 364-365 V Total time in seconds to complete off-line data collection activity 366 X Vendor specific 367 F Off-line data collection capability 368-369 F SMART capability Error logging capability 370 F 7-1 Reserved 0 1=Device error logging supported 371 X Vendor specific 372 F Short self-test routine recommended polling time (in minutes) 373 F Extended self-test routine recommended polling time (in minutes) 374 F Conveyance self-test routine recommended polling time (in minutes) 375-385 R Reserved 386-395 F Date Code 396-397 F Number of initial invalid block (396 = MSB, 397 = LSB) 398-399 V Number of run time bad block (398 = MSB, 399 = LSB) 400 V Number of spare block Transcend Information Inc. 10 V0.1 7P Horizontal Type TS128M~8GSDOM7H 511 V SATA Flash Modules Data structure checksum F=the content of the byte is fixed and does not change. V=the content of the byte is variable and may change depending on the state of the device or the commands executed by the device. X=the content of the byte is vendor specific and may be fixed or variable. R=the content of the byte is reserved and shall be zero. * 4 Byte value : [MSB] [2] [1] [LSB] Transcend Information Inc. 11 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules ID Table Table Information Word Address Default Value Total Bytes 044Ah 2 General configuration – Bit Significant with ATA-7 definitions. 1 XXXXh 2 Default number of cylinders 2 0000h 2 Reserved 3 00XXh 2 Default number of heads 4 0000h 2 Obsolete 5 0240h 2 Obsolete 6 XXXXh 2 Default number of sectors per track Data Field Type Information 7-8 XXXXh 4 Number of sectors per card (Word 7 = MSW, Word 8 = LSW) 9 XXXXh 2 Obsolete 10-19 aaaa 20 Serial number in ASCII (Right Justified) 20 0002h 2 Obsolete 21 0002h 2 Obsolete 22 0000h 2 Number of ECC bytes passed on Read/Write Long Commands 23-26 aaaa 8 Firmware revision in ASCII. Big Endian Byte Order in Word 27-46 aaaa 40 Model number in ASCII (Left Justified) Big Endian Byte Order in Word 47 XXXXh 2 Maximum number of sectors on Read/Write Multiple command 48 0000h 2 Reserved 49 0F00h 2 Capabilities ( Default) 50 0000h 2 Reserved 51 0200h 2 PIO data transfer cycle timing mode (PIO mode 2) 52 0000h 2 Obsolete 53 0007h 2 Field Validity 54 XXXXh 2 Current numbers of cylinders 55 XXXXh 2 Current numbers of heads 56 XXXXh 2 Current sectors per track 57-58 XXXXh 4 Current capacity in sectors (LBAs)(Word 57 = LSW, Word 58 = MSW) 59 0100h 2 Multiple sector setting 60-61 XXXXh 4 Total number of sectors addressable in LBA Mode 62 0000h 2 Reserved 63 0007h 2 Multiword DMA transfer. (Support Multiword mode 0-2) 64 0003h 2 Advanced PIO modes supported (Support PIO mode 3 and PIO mode 4) 65 0078h 2 Minimum Multiword DMA transfer cycle time per word. (120ns) 66 0078h 2 Recommended Multiword DMA transfer cycle time. (120ns) 67 0078h 2 Minimum PIO transfer cycle time without flow control (120ns) Transcend Information Inc. 12 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Word Address Default Value Total Bytes 68 0078h 2 Minimum PIO transfer cycle time with IORDY flow control (120ns) 69-79 0000h 22 Reserved 80 0080h 2 Major revision number Data Field Type Information 81 0000h 2 Mimor revision number 82 742Bh 2 Command sets supported 0 83 5008h 2 Command sets supported 1 84 4003h 2 Command sets supported 2 85 XXXXh 2 Command sets Enable 0 86 XXXXh 2 Command sets Enable 1 87 4003h 2 Command sets Enable 2 88 003Fh 2 Ultra DMA Mode Supported and Selected 89 0001h 2 Time required for Security erase unit completion (2 min) 90 0000h 2 Time required for Enhanced security erase unit completion 91 0000h 2 Current Advanced power management value 92 0000h 2 Reserved 93 XXXXh 2 Hardware configuration test result 94-127 0000h 68 Reserved 128 0001h 2 Security status (Default) 129-159 0000h 62 Vendor unique bytes 160 0000h 2 Power requirement description 161-255 0000h 190 Transcend Information Inc. Reserved 13 V0.1 7P Horizontal Type TS128M~8GSDOM7H SATA Flash Modules Ordering Information TS XG SDOM XX Connector type 7H = 7pin SATA horizontal 22V = 22pin SATA vertical 22H = 22pin SATA horizontal SATA Flash Module Transcend Product Capacity: 128M-8G 1. The above technical information is based on industry standard data and has been tested to be reliable. However, Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product. Transcend reserves the right to make changes to the specifications at any time without prior notice. 2. For specific capacity, performance, and reliability requirement, please contact with sales. TAIWAN No.70, XingZhong Rd., NeiHu Dist., Taipei, Taiwan, R.O.C TEL +886-2-2792-8000 Fax +886-2-2793-2222 E-mail: [email protected] www.transcend.com.tw Transcend Information Inc. USA Los Angeles: E-mail: [email protected] Maryland: E-mail: [email protected] www.transcendusa.com CHINA E-mail: [email protected] www.transcendchina.com GERMANY E-mail: [email protected] www.transcend.de HONG KONG E-mail: [email protected] www.transcendchina.com JAPAN E-mail: [email protected] www.transcend.jp THE NETHERLANDS E-mail: [email protected] www.transcend.nl United Kingdom E-mail: [email protected] www.transcend-uk.com Korea E-mail: [email protected] www.transcend.co.kr 14 V0.1