PSM Series Open Frame 40~65 Watts Single Output AC/DC Medical Power Supply FEATURES ● Open Frame ● Single Output ● Universal AC Input: 90~264VAC ● Output Voltages from 5 to 52VDC ● Over Voltage/ Over Load/ Short Circuit Protected ● 4(L) x 2(W) x 1.18(H) inches (101.6 x 50.8 x 30 mm) SPECIFICATIONS: PSM Series All specifications are based on 25oC, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage Input Frequency Input Current Inrush Current OUTPUT SPECIFICATIONS Output Voltage Output Power Range Output Regulation Output Current Ripple & Noise (20MHz BW) Hold-Up Time Temperature Coefficient PROTECTION Short Circuit Protection Over Voltage Protection Over Load Protection GENERAL SPECIFICATIONS Efficiency ENVIRONMENTAL SPECIFICATIONS 90 – 264VAC 47 to 63Hz 2A(rms) @ 115VAC < 40A @ 115VAC at 25°C cold start, < 80A @ 230VAC at 25°C cold start Operating Temperature Humidity (non-condensing) Cooling MTBF PHYSICAL SPECIFICATIONS Weight 0°C to +50°C ambient, each output derates at 2.5% per degree from +50°C to 70°C. 20% to 90% Free air convection 100,000 hrs at full load and 25°C ambient. Dimensions SAFETY & EMC Safety Standards EMC Standards See Table 65 Watts max with convection cooling. See table See Table 1% 10ms at max watt load and 115VAC nominal line. All outputs ±0.04%/°C max. Auto recover Output 110% to 130% above following nominal output. Latching Type. AC recycle. Over load protected @ 120% to 180% above following maximum rating. Auto recover. 80% typical at full output 7oz 4(L) x 2(W) x 1.18(H) inches 101.6(L) x 50.8(W) x 30(H) mm UL/cUL UL60601-1, TUV EN60601-1, CB IEC 60601-1 EN60601-1-2, FCC Part 18 Class B, EN55011 Class B, CE Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSM Series Open Frame 40~65 Watts Single Output AC/DC Medical Power Supply OUTPUT VOLTAGE / CURRENT RATING CHART Model PSM040B-1Y050 PSM060B-1Y120 PSM060B-1Y150 PSM065B-1Y190 PSM065B-1Y240 PSM065B-1Y360 PSM065B-1Y480 Output Voltage Range 5 - 7VDC 11-13VDC 14-17VDC 18-21VDC 22-26VDC 33-39VDC 44-52VDC Preset Voltage 5VDC 12VDC 15VDC 19VDC 24VDC 36VDC 48VDC Max. Output Current (convection cooling) 8A 5A 4A 3.43A 2.71A 1.81A 1.36A Output Power 40W 60W 60W 65W 65W 65W 65W Output Regulation 5% 3% 3% 3% 3% 2% 2% Ripple & Noise 50mVp-p 120mVp-p 150mVp-p 190mVp-p 240mVp-p 360mVp-p 480mVp-p NOTES 1. At 25°C including initial tolerance, line voltage, load currents, and output voltages adjusted to factory settings. 2. Ripple and Noise: Peak-to-peak with 20mHz bandwidth with a tantalum 10uF capacitor in parallel with a 0.1uF ceramic capacitor. 3. Other DC outputs available for 40W (5 to 7V), 60W (11 to 13V and 14 to 17V), 65W (18 to 21V, 22 to 26V, 33 to 39V, and 44 to 52V), set at factory. To determine part numbers for output voltages not listed see the “Part Number Guide” table below. 4. All output ranges are covered in agency certification and the preset voltage will be set as standard models. If any request is not standard output, please contact us prior to ordering. Part Number Guide PSM040B-1YW (5-7V) PSM060B-1YX (11-13V) PSM060B-1YX (14-17V) PSM065B-1YZ (18-21V) PSM065B-1YZ (22-26V) PSM065B-1YZ (33-39V) PSM065B-1YZ (44-52V) W= 050-070 X = 110-170 Z = 180-520 Ex: For a 6V output the part number would be PSM040B-1Y060 For a 12.2V output the part number would be PSM060B-1Y122 For a 33.4V output the part number would be PSM065B-1Y334 MECHANICAL DRAWING MATCHING CONNECTORS CN1 = AC INPUT MOLEX P/N: 09-65-2029 (OR EQUIVALENT) FEMALE HOUSING MOLEX P/N: 09-76-1020 (OR EQUIVALENT) CN2 = DC OUTPUT MOLEX P/N: 09-65-2048 (OR EQUIVALENT) FEMALE HOUSING MOLEX P/N: 09-52-4044 (OR EQUIVALENT) Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797