TI SN74LV74AMPWREP

SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
FEATURES
•
•
•
•
•
•
•
•
•
•
•
(1)
Controlled Baseline
– One Assembly/Test Site, One Fabrication
Site
Extended Temperature Performance of– 55°C
to 125°C
Enhanced Diminishing Manufacturing
Sources (DMS) Support
Enhanced Product-Change Notification
Qualification Pedigree (1)
2-V to 5.5-V VCC Operation
Max tpd of 13 ns at 5 V
Typical VOLP (Output Ground Bounce)
<0.8 V at VCC = 3.3 V, TA = 25°C
Typical VOHV (Output VOH Undershoot)
>2.3 V at VCC = 3.3 V, TA = 25°C
Supports Mixed-Mode Voltage Operation on
All Ports
Ioff Supports Partial-Power-Down Mode
Operation
•
•
Latch-Up Performance Exceeds 250 mA Per
JESD 17
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
PW PACKAGE
(TOP VIEW)
1CLR
1D
1CLK
1PRE
1Q
1Q
GND
1
14 VCC
2
13 2CLR
3
12 2D
4
11 2CLK
5
10 2PRE
6
7
9 2Q
8 2Q
Component qualification in accordance with JEDEC and
industry standards to ensure reliable operation over an
extended temperature range. This includes, but is not limited
to, Highly Accelerated Stress Test (HAST) or biased 85/85,
temperature cycle, autoclave or unbiased HAST,
electromigration, bond intermetallic life, and mold compound
life. Such qualification testing should not be viewed as
justifying use of this component beyond specified
performance and environmental limits.
DESCRIPTION/ORDERING INFORMATION
These dual positive-edge-triggered D-type flip-flops are designed for 2-V to 5.5-V VCC operation.
A low level at the preset (PRE) or clear (CLR) inputs sets or resets the outputs, regardless of the levels of the
other inputs. When PRE and CLR are inactive (high), data at the data (D) inputs meeting the setup-time
requirements is transferred to the outputs on the positive-going edge of the clock pulse. Clock triggering occurs
at a voltage level and is not directly related to the rise time of the clock pulse. Following the hold-time interval,
data at the D input can be changed without affecting the levels at the outputs.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the devices when they are powered down.
ORDERING INFORMATION
PACKAGE (1)
TA
–55°C to 125°C
(1)
TSSOP – PW
Reel of 2000
ORDERABLE PART NUMBER
SN74LV74AMPWREP
TOP-SIDE MARKING
LV74AEP
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains ADVANCE
INFORMATION on new products in the sampling or preproduction
phase of development. Characteristic data and other specifications
are subject to change without notice.
Copyright © 2006, Texas Instruments Incorporated
SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
FUNCTION TABLE
INPUTS
(1)
OUTPUTS
PRE
CLR
CLK
D
Q
L
H
X
X
H
Q
L
H
L
X
X
L
H
L
L
X
X
H (1)
H (1)
H
H
↑
H
H
L
H
H
↑
L
L
H
H
H
L
X
Q0
Q0
This configuration is nonstable; that is, it does not persist when
PRE or CLR returns to its inactive (high) level.
LOGIC DIAGRAM, EACH FLIP-FLOP (POSITIVE LOGIC)
PRE
CLK
C
C
C
Q
TG
C
C
C
C
D
TG
TG
TG
C
C
C
Q
CLR
2
SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
Absolute Maximum Ratings
(1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
–0.5
7
V
VI
Input voltage range (2)
–0.5
7
V
–0.5
7
V
–0.5
VCC + 0.5
state (2)
UNIT
VO
Voltage range applied to any output in the high-impedance or power-off
VO
Output voltage range (2) (3)
IIK
Input clamp current
VI < 0
–20
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
VO = 0 to VCC
±25
mA
±50
mA
113
°C/W
150
°C
Continuous current through VCC or GND
θJA
Package thermal
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
impedance (4)
–65
V
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
This value is limited to 5.5 V maximum.
The package thermal impedance is calculated in accordance with JESD 51-7.
3
SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
Recommended Operating Conditions (1)
VCC
Supply voltage
VCC = 2 V
VIH
High-level input voltage
MIN
MAX
2
5.5
Low-level input voltage
VI
Input voltage
VO
Output voltage
VCC = 2.3 V to 2.7 V
VCC × 0.7
VCC = 3 V to 3.6 V
VCC × 0.7
VCC = 4.5 V to 5.5 V
VCC × 0.7
V
0.5
VCC = 2.3 V to 2.7 V
VCC × 0.3
VCC = 3 V to 3.6 V
VCC × 0.3
0
5.5
0
VCC
V
–50
µA
VCC = 2 V
VCC = 2.3 V to 2.7 V
High-level output current
VCC = 3 V to 3.6 V
–6
∆t/∆v
2
VCC = 3 V to 3.6 V
6
VCC = 4.5 V to 5.5 V
12
VCC = 2.3 V to 2.7 V
200
VCC = 3 V to 3.6 V
100
VCC = 4.5 V to 5.5 V
TA
(1)
µA
50
VCC = 2.3 V to 2.7 V
Input transition rise or fall rate
mA
–12
VCC = 2 V
Low-level output current
V
–2
VCC = 4.5 V to 5.5 V
IOL
V
VCC × 0.3
VCC = 4.5 V to 5.5 V
IOH
V
1.5
VCC = 2 V
VIL
UNIT
mA
ns/V
20
Operating free-air temperature
–55
°C
125
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
VOH
TEST CONDITIONS
IOH = –2 mA
2.3 V
IOH = –6 mA
3V
2.48
4.5 V
3.8
4
MAX
2
IOL = 2 mA
2.3 V
0.4
IOL = 6 mA
3V
0.44
4.5 V
0.55
VI = 5.5 V or GND
VI = VCC or GND, IO = 0
Ioff
VI or VO = 0 to 5.5 V
VI = VCC or GND
UNIT
V
2 V to 5.5 V
ICC
Ci
TYP
VCC – 0.1
IOL = 50 µA
IOL = 12 mA
II
MIN
2 V to 5.5 V
IOH = –12 mA
VOL
VCC
IOH = –50 µA
0.1
V
0 to 5.5 V
±1
µA
5.5 V
20
µA
0
5
µA
3.3 V
2
5V
2
pF
SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
Timing Requirements
over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1)
TA = 25°C
PARAMETER
tw
Pulse duration
tsu
Setup time before CLK↑
th
Hold time, data after CLK↑
MIN
MAX
MIN
PRE or CLR low
8
9
CLK
8
9
Data
8
9
PRE or CLR inactive
7
7
0.5
0.5
MAX
UNIT
ns
ns
ns
Timing Requirements
over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1)
TA = 25°C
PARAMETER
tw
Pulse duration
tsu
Setup time before CLK↑
th
Hold time, data after CLK↑
MIN
MAX
MIN
PRE or CLR low
6
7
CLK
6
7
Data
6
7
PRE or CLR inactive
5
5
1.45
2.15
MAX
UNIT
ns
ns
ns
Timing Requirements
over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1)
TA = 25°C
PARAMETER
tw
Pulse duration
tsu
Setup time before CLK↑
th
Hold time, data after CLK↑
MIN
MAX
MIN
PRE or CLR low
5
5
CLK
5
5
Data
5
5
PRE or CLR inactive
3
3
1.45
2.15
MAX
UNIT
ns
ns
ns
Switching Characteristics
over recommended operating free-air temperature range,VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
fmax
tpd
LOAD
CAPACITANCE
CL = 50 pF
PRE or CLR
CLK
Q or Q
CL = 50 pF
TA = 25°C
MIN
TYP
30
70
MAX
MIN
MAX
25
UNIT
MHz
13
17.4
1
20
14.2
20
1
23
ns
5
SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
Switching Characteristics
over recommended operating free-air temperature range,VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
fmax
tpd
CL = 50 pF
PRE or CLR
Q or Q
CLK
TA = 25°C
MIN
TYP
50
90
CL = 50 pF
MIN
MAX
MAX
UNIT
45
MHz
9.2
15.8
1
18
10.2
15.4
1
18
ns
Switching Characteristics
over recommended operating free-air temperature range,VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
fmax
tpd
CL = 50 pF
PRE or CLR
CLK
Q or Q
CL = 50 pF
TA = 25°C
MIN
TYP
90
140
MIN
MAX
MAX
UNIT
75
MHz
6.6
9.7
1
12
7.2
9.9
1
13
ns
Noise Characteristics (1)
VCC = 3.3 V, CL = 50 pF, TA = 25°C
PARAMETER
TYP
MAX
0.1
0.8
V
Quiet output, minimum dynamic VOL
0
–0.8
V
Quiet output, minimum dynamic VOH
3.2
VOL(P)
Quiet output, maximum dynamic VOL
VOL(V)
VOH(V)
VIH(D)
High-level dynamic input voltage
VIL(D)
Low-level dynamic input voltage
(1)
MIN
UNIT
V
2.31
V
0.99
V
Characteristics are for surface-mount packages only.
Operating Characteristics
TA = 25°C
PARAMETER
Cpd
6
Power dissipation capacitance
TEST CONDITIONS
CL = 50 pF,
f = 10 MHz
VCC
TYP
3.3 V
21
5V
23
UNIT
pF
SN74LV74A-EP
DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS
www.ti.com
SCLS696 – JANUARY 2006
PARAMETER MEASUREMENT INFORMATION
VCC
From Output
Under Test
Test
Point
RL = 1 kΩ
From Output
Under Test
CL
(see Note A)
S1
Open
TEST
GND
CL
(see Note A)
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open Drain
Open
VCC
GND
VCC
LOAD CIRCUIT FOR
3-STATE AND OPEN-DRAIN OUTPUTS
VCC
50% VCC
Timing Input
0V
tw
tsu
VCC
50% VCC
Input
50% VCC
th
VCC
50% VCC
Data Input
50% VCC
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VCC
50% VCC
Input
50% VCC
tPLH
tPHL
50% VCC
tPHL
50% VCC
VOL
50% VCC
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
tPLZ
≈VCC
50% VCC
tPZH
VOH
50% VCC
0V
Output
Waveform 1
S1 at VCC
(see Note B)
tPLH
50% VCC
50% VCC
tPZL
VOH
In-Phase
Output
Out-of-Phase
Output
0V
VCC
Output
Control
Output
Waveform 2
S1 at GND
(see Note B)
VOL + 0.3 V
VOL
tPHZ
50% VCC
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns.
D. The outputs are measured one at a time, with one input transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPHL and tPLH are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuits and Voltage Waveforms
7
PACKAGE OPTION ADDENDUM
www.ti.com
9-May-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
SN74LV74AMPWREP
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Add to cart
V62/06605-01XE
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Add to cart
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN74LV74A-EP :
• Catalog: SN74LV74A
• Automotive: SN74LV74A-Q1
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
9-May-2012
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
SN74LV74AMPWREP
Package Package Pins
Type Drawing
TSSOP
PW
14
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
12.4
Pack Materials-Page 1
6.9
B0
(mm)
K0
(mm)
P1
(mm)
5.6
1.6
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN74LV74AMPWREP
TSSOP
PW
14
2000
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated