AC-DC 800 Watts xppower.com SMR Series • Up to 900 W Peak Output Power • Single Outputs from 12 V to 60 V • Active PFC • Remote On/Off • Semi F47 Compliant • Optional Current Share • Optional Input & Output Connectors Specification Input Input Voltage Input Frequency Input Current Inrush Current Power Factor Earth Leakage Current Input Protection General • • • • • • • 90-264 VAC (120-370 VDC) 47-63 Hz 12 A at 90 VAC, 6 A at 230 VAC 70 A at 230 VAC 0.99 typical <2.4 mA max at 264 VAC Fitted with a T12 A/250 V fuse Efficiency Isolation Switching Frequency Power Density Signals Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Line Regulation Load Regulation Over/Undershoot Transient Response • • • • • • • • • • • See tables ±5% ±1% 1% to meet ripple & noise spec 1.0 s at 230 VAC 40 ms typical 16 ms min at 120 VAC ±0.5%, low line to high line ±1%, 1-100% load (see note 4) 5% max 5% max deviation, 500 µs recovery to within 1% for a 50% load change Ripple & Noise • 50 mV (Vo ≤ 5 V), 1% (Vo ≥ 12 V) (see note 2) Overvoltage Protection • 110-130% recycle input to reset Overtemperature • Measured internally with auto recovery Protection Overload Protection • 110-140% with auto recovery Short Circuit Protection • Trip and restart (Hiccup mode) Remote Sense • Compensates for up to 0.5 V line drop Remote On/Off • On = TTL Logic HIGH, or open circuit Off = TTL Logic LOW or short circuit Current Share • Optional single wire current share within 10% for up to 4 units (add suffix ‘-I’ to model number) Note that this option includes output blocking diodes. Remote sense is not available with current share. Current Monitor MTBF • 80% min for 12 V model 82% min for others models at 230 VAC • 3000 VAC Input to Output 1500 VAC Input to Ground 250 VDC Output to Ground • 25 kHz PWM, 60 kHz PFC • 8.2 W/In3 • Green LED for Power On, Power Good TTL HIGH within 100-500 ms and LOW ≤1 ms before loss of regulation • 0.5 V to 3 V output denoting 0-100% output current • 150 kHrs min per MIL-HDBK-217F Environmental Operating Temperature • 0 to +70 ˚C, derates from 100% load at +50 ˚C to 50% load at +70 ˚C Cooling • Internal fan Operating Humidity • 5-90%, non-condensing Storage Temperature • -20 ˚C to +85 ˚C Operating Altitude • 3000 m Vibration • 5-50 Hz, acceleration 7.35 ms2 on X, Y and Z axis EMC & Safety Emissions Harmonic Currents ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • FCC Part 15 & EN55022 Level B conducted • EN61000-3-2-3-3 • EN61000-4-2, level 3 Perf Criteria A • EN61000-4-3, 3 V/m Perf Criteria A • EN61000-4-4, level 2 Perf Criteria A • EN61000-4-5, level 3 Perf Criteria A • EN61000-4-6, 3V Perf Criteria A • EN61000-4-11 70% UT for 10 ms, 40% UT for 100 ms, <5% UT for 5000 ms Perf Criteria A, B, B • UL60950, CSA C22.2 No. 950, EN60950-1:2001, CE Mark LVD, SEMI F47 compliant (high line only) at 100% rated power output Output Power Output Current Maximum Peak(1) 62.50 A 75.00 A 50.00 A 56.00 A 41.67 A 50.00 A 33.39 A 37.50 A 29.62 A 33.33 A 25.00 A 29.60 A 16.67 A 18.75 A 14.81 A 16.67 A 13.33 A 15.00 A Output Voltage(3,4) 12 V 15 V 18 V 24 V 27 V 36 V 48 V 54 V 60 V 750 W 800 W Model Number SMR800PS12 SMR800PS15 SMR800PS18 SMR800PS24 SMR800PS27 SMR800PS36 SMR800PS48 SMR800PS54 SMR800PS60 Ripple & Noise(2) 120 150 180 240 270 360 480 540 600 mV mV mV mV mV mV mV mV mV Notes 1. This peak can be taken for 500 µs only, average power should not exceed the maximum power. 2. Ripple & Noise is measured using 0.1 µF ceramic and 22 µF electrolytic capacitor, 20 MHz bandwidth. 3. Alternative output voltages available. Consult sales. 4. Load regulation increases to 2% for 0-100% load change. Mechanical Details 0.22 (5.6) M4 (Zn (yellow) -plated) A 0.25 (6.4) 0.07 (1.9) 0.02 (0.6) 0.02 (0.6) 2.00 (50.8) 2.50 (63.5) 0.22 (5.6) 0.25 (6.4) 0.07 (1.9) Pin 1 2* 3 4 5 6* 7* A Mounting Hole 8 Places B Mounting Hole 8 Places UNC6-32 (Zn-plated) B B 2.09 (53.0) A 1.59 (40.4) 5.00 (127.0) CN3 Pin 7 0.59 (15.0) L N OPTION ‘-D’ IEC320 or equivalent FAN A A B B 1.75 (44.45) 2.50 (63.6) B 1.62 0.32 (8.25) (41.25) VO- 2.50 (63.5) 6.00 (152.4) *If optional current share if fitted then remote sense function is excluded. 2.50 (63.5) For SMS Version only B A 1.25 (31.9) STANDARD Terminal Block M3 Screw 3 Pins 8.25 mm center A 0.88 (22.25) Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center 9.17 (233.0) A 4.25 (108.0) Pin 1 VO+ 2.50 (63.5) 1.59 (40.3) CN3 (Signals) Function Current monitor Current share Return Power good Remote On/Off -Remote sense +Remote sense B B All dimensions are in inches (mm). Weight: 3.30 lbs (1.5 kg) approx. Logic connector CN3 mates with: JST XHP-7 or equivalent & JST SXH-002T-P0.6 crimp terminals. Maximum mounting screw penetration: 0.12 (3.0) on base & 0.25 (6.3) on each side. 2.50 (63.5) A 2.00 (50.8) 9.17 (233.0) Options • Current share and internal oring diode add suffix ‘-I’ to model number. Note that this option includes output blocking diodes. Remote sense is not available with current share. • Optional IEC320 inlet add suffix‘-D’ to model number. • Optional Molex output connector add suffix ‘-E’ to model number. • For U-Channel version replace ‘SMR’ in the model number with ‘SMS’ e.g. SMS800PS12 (note that 25 CFM cooling air is required). Dimensions are 8.00(l) x 4.33(w) x 2.56(h) (203.2 x 110.0 x 65.0). • For top mounting fan version replace ‘SMR’ in the model number with ‘SMT’ e;g; SMT800PS12. Dimensions are 8.00(l) x 4.33(w) x 3.40(h) (203.2 x 110.0 x 86.4). • For multiple option codes place codes in alphabetical order. e.g. SMR800PS12-DI. Application Notes Parallel Connect with Current Share Option Remote On/Off Power Good +5 V Supply 1 Output Return CN3 Pin 2 Current Share PSU V1 CN3 Pin 5, control connector ON/OFF 1K CN3 Pin 4, control connector Power Good POWER GOOD LOAD Comm Supply 2 Output Return CN3 Pin 2 Current Share CN3 Pin 3, control connector Return Note: Applying <0.3 V or short between pins 5 and 3 turns the output OFF. Applying >4.5 V or open circuit between pins 5 and 3 turns output ON. CN3 Pin 3, control connector Return POWER NOT GOOD Sink current = 6 mA Source current = 4 mA 17-Apr-07 AC-DC SMR Series Models and Ratings