XPPOWER PBM200PQ02-C

AC-DC
200 Watts
xppower.com
PBM200 Series
•
Worldwide Medical Approvals
•
Single, Dual, Triple and Quad Outputs
•
Small Size - Only 7” x 4” x 1.5”
•
Power Fail Detect & Remote On/Off
•
Universal AC Input with Active PFC
•
High Reliability - 350k Hours MTBF
•
100 Watt Convection-Cooled Rating
Specification
Input
General
Input Voltage
Input Frequency
Input Current
• 90-264 VAC
• 47-63 Hz
• 3.2 A rms at 115 VAC,
1.6 A rms at 230 VAC
Inrush Current
• 20 A at 115 VAC, 40 A at 230 VAC
cold start 25 ºC
Power Factor
• 0.98 typical
Earth Leakage Current • 90 µA max at 115 VAC, 60 Hz
150 µA max at 230 VAC, 50 Hz
Input Protection
• Both line and neutral fused
Output
Output Voltage
Output Voltage Trim
Initial Set Accuracy
Minimum Load
Start Up Delay
Start Up Rise Time
Hold Up Time
Drift
Line Regulation
Load Regulation
Transient Response
•
•
•
•
•
•
•
•
•
•
•
Ripple & Noise
•
Overvoltage Protection •
Overtemperature
Protection
•
Overload Protection
Short Circuit Protection
Temperature
Coefficient
Remote Sense
•
•
•
Remote On/Off
See table
Not user-adjustable
±2%
See table & note 5
2 s max
18 ms typical
20 ms minimum at full load & 110 VAC
±0.2%
±0.5% max
See note 7
4% max deviation, recovery to within
1% in 500 µs for a 25% load change
2% max pk-pk, 20 MHz BW with a 22 µF
electrolytic & a 0.47 µF tantalum capacitor
112-140% Vnom output 1 only, recycle
input to reset
Shutdown at +85 ºC (singles) or +105 ºC
(multi outputs) with auto recovery,
measured internally
140-200% typical, auto recovery
Trip and restart (Hiccup mode)
0.04%/˚C
• Single output models only.
Compensates for up to 0.5 V drop
• On = Logic low or open circuit
Off = Logic high
Efficiency
Isolation
Switching Frequency
Power Density
Power Fail Detect
MTBF
• Up to 80%
• 4000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
• 100 kHz ±12 kHz
• 4.76 W/In3
• AC OK = TTL logic high
AC not OK = TTL logic low
• 350 kHrs per MIL-HDBK-217F at +25 ˚C
Environmental
Operating Temperature • 0 ˚C to +70 ˚C, derate linearly from 100%
power at +50 ˚C to 50% power at +70 ˚C
Cooling
• ‘C’ versions have internal fan,
‘B’ versions are derated with convection
cooling or require 25 CFM (see note 4)
Operating Humidity
• Up to 95% RH, non-condensing
Storage Temperature
• -40 ˚C to +85 ˚C
Operating Altitude
• 2500 m
Shock
• Half sine pulse. acceleration 50 g, 11 ms
duration, 3 shocks in each direction,
unpackaged, non-operating
Vibration
• Sinusoidal 10-55 Hz, amplitude 0.15 mm,
30 min/axis, unpackaged, non-operating
EMC & Safety
Emissions
Harmonic Currents
Voltage Flicker
ESD Immunity
Radiated Immunity
EFT/Burst
Surge
Conducted Immunity
Dips & Interruptions
Safety Approvals
• EN55011 & FCC Class B conducted
& radiated
• EN61000-3-2
• EN61000-3-3
• EN61000-4-2, level 3 Perf Criteria A
• EN61000-4-3, level 3 Perf Criteria A
• EN61000-4-4, level 3 Perf Criteria A
• EN61000-4-5, level 3 Perf Criteria A
• EN61000-4-6 3 V, Perf Criteria A
• EN61000-4-11, 30% 10 ms,
60% 100 ms, >95% 5000 ms,
Perf Criteria A, B, B
• EN60601-1, UL60601-1,
CSA22.2 No. 601-1 per cUL, CE Mark
Output 1(8)
Output
Power(4)
Vnom
(5)
Output 2(2,5)
(7)
Imin
Imax
Reg
Vnom
Output 3(5)
(7)
Imax
Reg
Vnom
Output 4(3,5)
(7)
Imax
Reg
Vnom
Imax
Model
Number(1)
Reg(7)
150 W
3.3 V
3.0 A
46.0 A
3%
PBM200PS3V3-C†
175 W
5.1 V
3.0 A
35.0 A
2%
PBM200PS05-C†
200 W
12.0 V
1.2 A
16.7 A
2%
PBM200PS12-C†
200 W
15.0 V
1.0 A
13.4 A
2%
PBM200PS15-C†
200 W
24.0 V
0.6 A
8.4 A
2%
PBM200PS24-C†
200 W
30.0 V
0.5 A
6.7 A
2%
PBM200PS30-C
200 W
48.0 V
0.5 A
4.2 A
2%
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
4%
PBM200PD01-C
200 W
+5.1 V
3.0 A
30.0 A
2%
+15 V
6.0 A
4%
PBM200PD02-C
200 W
+5.1 V
3.0 A
30.0 A
2%
+24 V
4.0 A
4%
PBM200PD03-C
200 W
+12.0 V
1.0 A
8.7 A
2%
+24 V
4.0 A
4%
PBM200PD04-C
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
4%
-5 V
6.0 A
4%
PBM200PT01-C
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
4%
-12 V
4.0 A
4%
PBM200PT02-C†
200 W
+5.1 V
3.0 A
30.0 A
2%
+15 V
6.0 A
4%
-15 V
4.0 A
4%
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
4%
200 W
+5.1 V
3.0 A
30.0 A
2%
+15 V
6.0 A
4%
-12 V
4.0 A
4%
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
4%
-12 V
4.0 A
200 W
+5.1 V
3.0 A
30.0 A
2%
+15 V
6.0 A
4%
-15 V
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
4%
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
8.0 A
200 W
+5.1 V
3.0 A
30.0 A
2%
+12 V
175 W
+3.3 V
3.0 A
30.0 A
3%
+5.1 V
PBM200PS48-C†
4%
PBM200PT03-C†
F 24 V
4.0 A
4%
PBM200PT04-C
4%
F5V
6.0 A
4%
PBM200PQ01-C
4.0 A
4%
F 24 V
4.0 A
4%
PBM200PQ02-C†
-12 V
4.0 A
4%
F 12 V
4.0 A
4%
PBM200PQ03-C
4%
-15 V
4.0 A
4%
F 15 V
4.0 A
4%
PBM200PQ04-C
8.0 A
4%
-12 V
4.0 A
4%
F 24 V
4.0 A
4%
PBM200PQ05-C†
8.0 A
4%
-12 V
4.0 A
4%
F 12 V
4.0 A
4%
PBM200PQ06-C†
PBM200PT05-C
Notes
1. For U-bracket format, replace suffix ‘-C’ with suffix ‘-B’.
2. Output 2 peak current is 12 A on +12 V, 9 A on +15 V, and 6 A on +24 V.
Maximum 2 s duration with total load <200 W.
3. Output 4 is floating and can be connected externally for positive or negative
output.
4. 200 W for ‘-C’ version with a cover and fan assembly. 100 W for ‘-B’ version
with convection cooling (maximum current of output 1 & 2 derated
to 50%). 200 W for ‘-B’ version with 25 CFM forced air provided by user.
5. Zero minimum load for outputs 2, 3 & 4. All models may be operated at noload on output 1, but voltage total regulation increases to 10%.
6. When the Remote Sense facility is not used, +Sense must be connected to
+V, and –Sense to return, on P2 connector.
7. Total regulation includes initial tolerance, line regulation and load regulation.
8. Peak current for single output models is 140% of Imax. Maximum 2 s duration
with 10% duty cycle.
9. † Available from Farnell. See pages 204-206.
Mechanical Details
Model Number(s)
B: Mounting holes. Threaded inserts for 6.32" screws (8 places)
A: Mounting holes. Threaded inserts for M3 0.5 screws (8 places)
Conn
B
B
A
A
1.00
(25.4)
P2
0.50
(12.7)
6.00 (152.4)
A
A
B
B
1
P2
P4
1
3.00
(76.2)
2.30
(58.4)
P3
P3
1
4.00
(101.6)
P5
P1
B
G
1.00
(25.4)
A
A
A
A
B
B
0.85
(21.6)
1.50
(38.1)
0.65
(16.5)
PDXX
PTXX
(except 04)
-SENSE
OP1
OP1
Return
OP1
OP1
Return Com Ret Com Ret
Return Com Ret Com Ret
Return Com Ret Com Ret
OP1
OP2
OP2
OP1
N.C.
OP3
OP1
N.C.
N.C.
+SENSE
N.C.
N.C.
Fan
Com Ret
Com Ret
PFD
PFD
PFD
PT04
PQXX
OP1
OP1
Com Ret
Com Ret
Com Ret
OP2
N.C.
OP4 Ret
OP4
OP1
OP1
Com Ret
Com Ret
Com Ret
OP2
OP3
OP4 Ret
OP4
PFD
PFD
Notes
B
9
0.50
(12.7)
PSXX
1
L
N
Pin
1
2
3
4
5
6
7
8
9
1
2
3
4
7.00 (177.8)
1. Dimensions shown in inches (mm).
2. Tolerance 0.02 [0.5] maximum.
3. Input connector P1 is Dinkle DT-35-B01W-03, output connector
P2 is Dinkle DT-35-B01W-09 screws are M3, Nickel plated.
4. Connector P3 mates with Molex housing 22-01-1043 & Molex
40445 series crimp terminal.
5. Connectors P4 & P5 mate with Molex housing 22-01-1023 &
Molex 40445 series crimp terminal.
6. P4 is for DC fan rated at 24 V/0.2 A (models PBM200PD03 &
PD04), 5 V/0.38 A (PBM200PQ06), or 12 V/0.2 A (all other
models). Pin 1 Fan+, pin 2 Fan-.
7. P5 is for Remote On/Off. Pin 1 is positive, pin 2 is return.
8. Weight:1.83 lb (0.82kg) approx. for ‘-B’ version, 2.14 lb (0.96kg)
approx. for ‘-C’ version.
17-Apr-07
AC-DC
PBM200
Models and Ratings