1N4001 THRU 1N4007 Voltage Range 50 to 1000 Volts Current 1.0 Amperes 1.0 AMP. SILICON RECTIFIERS DO-41 Features *Low forward voltage drop *High current capability *High reliability 1.0(25.4) MIN. *High surge current capability .107(2.7) .080(2.0) DIA. Mechanical Data *Cases:Molded plastic *Epoxy:UL 94V-0 rate flame retardant .205(5.2) .166(4.2) *Lead:Axial leads,solderable per MIL-STD-202, Method 208 guaranteed *Polarity:Color band denotes cathode end *High temperature soldering guaranteed: 1.0(25.4) MIN. 2500C/10 seconds/.375",(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension *Weight:0.35 gram .034(.86) .028(.71) DIA. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number 1N4005 1N4006 1N4007 UNITS 1N4001 1N4002 1N4003 1N4004 Maximum Repetitive Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage VRMS VDC 35 70 140 280 420 560 700 V 50 100 200 400 600 800 1000 V Maximum DC Blocking Voltage Maximum Average Forward Rectified oCurrent .375"(9.5mm) Lead Length @TA = 75 C IF(AV) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) IFSM Maximum Instantaneous Forward Voltage @1.0A o Maximun DC Reverse Current @ TA = 25 Co at Rated DC Blocking Voltage @ TA = 125 C Maximun Full Load Reverse Current, Full Cycle Average .375"(9.5mm) Lead Length 0 @TL=75 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating and Storage Temperature Range A 1.0 A 30 VF 1.0 V IR 5.0 50 uA uA IR 30 uA CJ 15 R*JA 50 TJ,TSTG NOTES: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 2.Thermal Resistance from Junction to Ambient .375"(9.5mm) Lead Length. -55 to+125 pF o C/W o C RATING AND CHARACTERISTIC CURVES 1N4001 THRU 1N4007 FIG.1- TYPICAL FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT.(A) AVERAGE FORWARD CURRENT AMPERES FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1.0 .8 .6 Single Phase Half Wave 60Hz Resistive or Inductive Load .375"(9.5mm) Lead Length .4 .2 0 0 25 50 75 100 125 150 175 20 10 2 1.0 .4 .2 0 Tj=25 C Pulse Width=300us 1% Duty Cycle .1 .04 .02 .01 .6 .8 0 FIG.3-MAXIMUN NON-REPETITIVE FORWARD SURGE CURRENT 1.4 1.5 100 40 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT.(A) 1.2 FIG.4- TYPICAL JUNCTION CAPACITANCE 50 8.3ms Single Half-Sine-Wave JEDEC Method 30 20 10 0 1 2 4 6 8 10 20 40 FIG.5-TYPICAL REVERSE CHARACTERISTICS 10 Tj=100oC 4 1.0 .4 .1 .04 Tj=25oC .01 0 20 40 60 80 100 120 60 80 100 60 40 20 10 0 Tj=25 C 6 4 2 1 NUMBER OF CYCLES AT 60Hz INSTANTANEOUS FORWARD CURRENT.(A) 1.0 FORWARD VOLTAGE.(V) AMBIENT TEMPERA TURE. ( C) 140 PERCENT OF RATED PEAK REVERSE VOLTAGE.(%) .1 .2 .4 1.0 2 4 10 REVERSE VOLTAGE.(V) 20 40 100