A-BRIGHT 61

A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Power White Surface Mount Device
Part Number: 61-23UWC
Package outlines & Re-flow Profile
„Reflow Temp/Time
„Soldering iron
Basic spec is U 5sec when 260℃. If temperature is higher,
time should be shorter (+10℃Æ -1sec ).Power dissipation
of iron should be smaller than 15W, and temperatures
should be controllable .Surface temperature of the device
should be under 230℃ .
ITEM
MATERIALS
Resin (mold)
Epoxy
Lens color
Yellow Diffused
Printed circuit board
BT
Emitted color
White
Material
InGaN
For reflow soldering (Propose)
NOTES:
1. All dimensions are in millimeters (inches);
2. Tolerances are ±0.1mm (0.004inch) unless otherwise
noted.
3. Polarity referring onto the cathode mark is reversed on the
red.
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: 61-23UWC
ELECTRO-OPTICAL CHARACTERISTICS
Parameter
(TA=25℃)
Test
Condition Symbol
Value
MIN. TYP. MAX.
120
Unit
Viewing angle at 50% IV
IF=10mA
2θ1/2
Forward voltage
IF=20mA
VF
2.8
IF=40mA*3line
IV
2600 3250 ---
mcd
IFP
100
mA
Luminous intensity
Peak pulsing current (1/10 duty f=1kHz)
---
Absolute maximum ratings
Parameter
Deg
3.8
V
(TA=25℃)
Symbol
Value
Unit
Forward current
IF
60
mA
Reverse voltage
VR
5
V
Reverse current
IR
10
µA
Power Consumptoin
PC
230
mW
Operating temperature range
Top
-40 ~+85
℃
Storage temperature range
Tstg
-40 ~+100
℃
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: 61-23UWC
CIE Chromaticity Diagram & Color Ranks
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: 61-23UWC
Typical Electro-Optical Characteristic Curves
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: 61-23UWC
Taping Dimension (Unit=mm)
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
SURFACE MOUNT LED LAMPS
Part Number: 61-23UWC
Precautions For Use
1. Over-current proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change (Burn out will happen).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded
the storage time, baking treatment should be performed using the following conditions.
Baking treatment︰60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3
seconds within once in less than soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is
often started at the time of the hand solder.