A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Full Color Chip LED Lamps Part Number: AL-HUBG6B433T Package outlines & Re-flow Profile Reflow Temp/Time Soldering iron Basic spec is U 5sec when 260℃. If temperature is higher, time should be shorter (+10℃Æ -1sec ).Power dissipation of iron should be smaller than 15W, and temperatures should be controllable .Surface temperature of the device should be under 230℃ . ITEM MATERIALS Resin (mold) Epoxy Lens color Water Clear Printed circuit board BT AlGaInP Dice InGaN InGaN For Reflow Soldering Brilliant Red Emitted color Brilliant Green Super Blue NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerances are ±0.1mm (0.004inch) unless otherwise noted. 3. Polarity referring onto the cathode mark is reversed on the red. A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T ELECTRO-OPTICAL CHARACTERISTICS Parameter Forward voltage Luminous intensity Wavelength Spectral Line Half-Width Peak pulsing current (1/10 duty f=1kHz) Power Dissipation Emitted Color R G B R G B R G B R G B R G B R G B R G B (TA=25℃) Value Test Symbol Condition MIN. TYP. MAX. IF=20mA VF IF=20mA IV − − − − − − λp IF=20mA λd IF=20mA △λ IF=20mA IFP IF=20mA PD − − − 2.0 3.5 3.5 140 180 70 632 518 468 625 525 470 20 30 30 60 100 100 60 110 110 Absolute maximum ratings Parameter 2.6 4.0 4.0 − − − Unit V mcd nm − − − nm mA mW (TA=25℃) Symbol Value Unit 2θ1/2 120 Deg Forward current IF 25 mA Reverse voltage VR 5 V Reverse current IR 100 μA Operating temperature range Top -40 ~+80 ℃ Storage temperature range Tstg -40 ~+85 ℃ Viewing angle at 50% Iv A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Test items and results of reliability Test Sample Size Ac/Re Hours/Cycle NO Item Test Conditions 1 Solder Heat TEMP：260±5℃ 5 Sec. 76 PCS 0/1 2 Temperature Cycle H：+85℃ 30min ∫ 5min L：-55℃ 30min 50 CYCLES 76 PCS 0/1 3 Thermal Shock H：+100℃ 5min ∫ 10set L：-10℃ 5min 50 CYCLES 76 PCS 0/1 4 High Temperature Storage TEMP：100℃ 1000 HRS 76 PCS 0/1 5 Low Temperature Storage TEMP：-55℃ 1000 HRS 76 PCS 0/1 6 DC Operating Life IF=20mA 1000 HRS 76 PCS 0/1 7 High Temperature / High Humidity 85℃ / 85%RH 1000 HRS 76 PCS 0/1 ＊Refer to reliability test standard specification for in this line. A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Typical Electro-Optical Characteristics Curves A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Typical Electro-Optical Characteristics Curves A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Precautions For Use 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment︰60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.