A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS 5630 Package Power Warm White Surface Mount Device Part Number: 62-217BSW1C1 Package outlines & Re-flow Profile Reflow Temp/Time Soldering iron Basic spec is U 5sec when 260℃. If temperature is higher, time should be shorter (+10℃Æ -1sec ).Power dissipation of iron should be smaller than 15W, and temperatures should be controllable .Surface temperature of the device should be under 230℃ . ITEM MATERIALS Resin (mold) Epoxy Lens color Yellow Diffused Printed circuit board BT Emitted color Warm White Material InGaN NOTES: 1. All dimensions are in millimeters (inches); 2. Tolerances are ±0.1mm (0.004inch) unless otherwise noted. 3. Polarity referring onto the cathode mark is reversed on the red. A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 ELECTRO-OPTICAL CHARACTERISTICS Parameter (TA=25℃) Test Condition Symbol Viewing angle at 50% IV IF=60mA 2θ1/2 Forward voltage IF=60mA VF Color Temperature IF=60mA CCT Luminous Flux IF=60mA Flux Pulse Forward Current Value MIN. TYP. MAX. 120 2.8 V 2750 3000 3250 K IFP (Pulse Width ≤ 10msec, and duty ≤1/10) 19 --- lm 150 Absolute maximum ratings Parameter Deg 3.5 --- --- Unit mA (TA=25℃) Symbol Value Unit Forward current IF 100 mA Reverse voltage VR 5 V Reverse current IR 1 μA Power dissipation PD 235 mW Operating temperature range Top -30 ~+80 ℃ Storage temperature range Tstg -40 ~+85 ℃ A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 Bin Code A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 Color Rank A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 CIE Chromaticity Diagram A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 Typical Electro-Optical Characteristic Curves A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 Packaging Tape, Reel, and Packing Model A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: 62-217BSW1C1 Precautions For Use 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment︰60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.