AMIS-710223-A6: 200dpi CIS Module Data Sheet 1.0 General Description The AMIS-710223-A6 (PI223MC-A6) is a contact imaging sensor (CIS) module, which is composed of 13 AMIS-720033 (PI3020) sensor chips. The AMIS-720033 is a 200 dot per inch (dpi) solid-state line imaging array, also a product of AMI Semiconductor. This imaging device is fabricated using MOS imaging sensor technology for high-speed performance and high sensitivity. The AMIS710223-A6 is suitable for scanning A6 size (104mm) documents with 8 dots per millimeter (dpm) resolution. Applications include ticket, check and card scanners, a variety of mark readers, and other automation equipment. 2.0 Key Features • • • • • • • • • Light source, lens and sensor are integrated into a single module 8dpm resolution, 104mm scanning length High speed page scan - up to 167µsec/line @ 5MHz pixel rate with internal optical modification (optional feature) Wide dynamic range Analog output Yellow-Green LED light source Compact size ≅ 14mm x 19mm x 120mm Low power Light weight 3.0 Functional Description The AMIS-710223-A6 imaging array consists of 13 sensors that are cascaded to provide 832 photo-detectors with their associated multiplex switches, and a digital shift register that controls its sequential readout. Mounted in the module is a one-to-one graded indexed micro lens array that focuses the scanned documents to image onto its sensing plane. The on-board amplifier processes the video signal to produce a sequential stream of video at the video output pin of the AMIS-710223-A6 module. Illumination is accomplished by means of an integrated LED light source. All components are housed in a small plastic housing which has a cover glass which acts as the focal point for the object being scanned and protects the imaging array, micro lens assembly and LED light source from dust. I/O to the module is the 10-pin connector located on one end of the module. The cross section of the AMIS-710223-A6 is shown in Figure 1 and the block diagram in Figure 2. AMI Semiconductor – May 06, M-20541-001 www.amis.com 1 AMIS-710223-A6: 200dpi CIS Module Figure 1: Inside Pictorial of the Module Figure 2: AMIS-710223-A6 Module Block Diagram AMI Semiconductor – May 06, M-20541-001 www.amis.com 2 Data Sheet AMIS-710223-A6: 200dpi CIS Module Table 1: Pin Configuration Pin Number 1 2 3 4 5 6 7 8 9 10 Symbol Vout Gnd Vdd (+5V) Vn (-5V to -12V) Gnd SP Gnd CP GLED VLED Data Sheet Names and Functions Analog video output Ground; 0V Positive power supply Negative power supply Ground; 0V Shift register start pulse Ground; 0V Sampling clock pulse Ground for the light source; 0V Supply for the light source 4.0 Absolute Maximum Rating Table 2: Absolute Maximum Rating Parameter Power supply voltage Input clock pulse (high level) Input clock pulse (low level) Symbols Vdd Idd Vn In VLED ILED Vih Vil Maximum Rating 7.5 40 -15 15 5.5 500 Vdd – 0.5V -0.6 Units V ma V ma V ma V V Table 3: Operating Temperature Parameter Operating temperature Operating humidity Storage temperature Storage humidity Symbols Top Hop Tstg Hstg Maximum Rating 0 to 50 10 to 85 -25 to +75 5 to 95 Units ° C % ° C % AMI Semiconductor – May 06, M-20541-001 www.amis.com 3 AMIS-710223-A6: 200dpi CIS Module Data Sheet 5.0 Electro-Optical Characteristics ° Table 4: Electro-Optical Characteristics at 25 C Parameter Number of photo detectors Pixel-to-pixel spacing Line scanning rate (2) Clock frequency (3) Bright output voltage (4) Bright output non-uniformity (5) Adjacent pixel non-uniformity (6) Dark non-uniformity Dark output voltage (7) Modulation transfer function Symbol Parameter 832 125 420 Units Elements µm µsec f 2 MHz Video output 1.0 V Up Uadj Ud Vd MTF <+/-30 <25 <20 <200 >50 % % mV mV % Tint (1) Note @ 2MHz clock frequency See Note 2 for 5.0MHz operation Specified for 420µsec See Note 7 for MTF & DOF Definition: 1. 2. 3. 4. 5. 6. 7. 8. 9. Tint: line scanning rate or integration time; tint is determined by the interval of two SP. See Note 2 for the high scanning speed operation. f: main clock frequency; the call out is at 2.0MHz, but electrically it reliably operates to 5.0MHz. However, it must be optically modified to obtain the minimum integration time of 167µsec. This modification is offered as a user's option. Vpavg = ∑ Vp(n)/832 Up = [(Vpmax - Vp) / Vp] x 100% or [(Vp - Vpmin) / Vp] x 100% Upadj = MAX[ | (Vp(n) - Vp(n+l) | / Vp(n)] x 100% Upadj is the nonuniformity percentage pixel to pixel. Ud = Vdmax – Vdmin Vdmin is the minimum output on a black document(O.D.=0.8). Vdmax: maximum output voltage of black document (O.D.= 0.8) MTF = [(Vmax - Vmin) / (Vmax + Vmin)] x 100 [%]. DOF range is defined with the MTF. MTF is measure at glass surface and at 0.4mm from the glass > 50 percent and peaks at approximately mid-point of 0.2mm. Vmax: maximum output voltage at 50lp/inch (At 1/2 of the optical Nyquest Frequency). Vmin: minimum output voltage at 50lp/inch. O.D. = optical density lp / inch: line pair per inch Table 5: Recommended Operating Conditions Item Power supply Input voltage at digital high Input voltage at digital low Clock frequency Clock pulse high duty cycle Clock pulse high duration Integration time Operating temperature Symbol Vdd Vn VLED Idd In ILED Vih Vil f Min. 4.5 -4.5 370 Vdd-1.0 0 Mean 5.0 -5 5 22 6 400 Vdd-0.5 2.0 Max. 5.5 -12 5.5 40 15 450 Vdd 0.6 5.0 25 5.0 50 25 50 0.167 Tint Top * Tint (min.) is the lowest line integration time available at a 5.0MHz clock rate with internal optical modifications. See Note 2 under Table 4. AMI Semiconductor – May 06, M-20541-001 www.amis.com 4 Units V V V ma ma ma V V MHz % ns ms ° C AMIS-710223-A6: 200dpi CIS Module Data Sheet 6.0 Switching Characteristics (25oC) Figure 3: Module Timing Diagram The switching characteristics for the I/O clocks are shown in Figure 3. Its corresponding timing symbol definitions are given in Table 6. Table 6: Symbol Definition for the Above Timing Diagram Item Symbol Clock cycle time to Clock pulse width tw Clock duty cycle Prohibit crossing time of SP tprh Data setup time tds Data hold time tdh Signal delay time tdl Signal settling time tsh AMI Semiconductor – May 06, M-20541-001 www.amis.com Min. 0.2 50 25 15 20 20 50 120 5 Typ. Max. 4.0 75 Units µs ns % ns ns ns ns ns AMIS-710223-A6: 200dpi CIS Module Data Sheet 7.0 AMIS-710223-A6 Module and its Mechanical Dimensions The sketch of this module is to provide a pictorial of the module size and structure. A detailed drawing is available upon request. Figure 4: Pictorial of the Plastic Standard A6 Housing Size AMI Semiconductor – May 06, M-20541-001 www.amis.com 6 AMIS-710223-A6: 200dpi CIS Module Data Sheet 8.0 Company or Product Inquiries For more information about AMI Semiconductor, our technology and our product, visit our Web site at: http://www.amis.com North America Tel: +1.208.233.4690 Fax: +1.208.234.6795 Europe Tel: +32 (0) 55.33.22.11 Fax: +32 (0) 55.31.81.12 Production Technical Data - The information contained in this document applies to a product in production. AMI Semiconductor and its subsidiaries (“AMIS”) have made every effort to ensure that the information is accurate and reliable. However, the characteristics and specifications of the product are subject to change without notice and the information is provided “AS IS” without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify that data being relied on is the most current and complete. AMIS reserves the right to discontinue production and change specifications and prices at any time and without notice. Products sold by AMIS are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMIS makes no other warranty, express or implied, and disclaims the warranties of noninfringement, merchantability, or fitness for a particular purpose. AMI Semiconductor's products are intended for use in ordinary commercial applications. These products are not designed, authorized, or warranted to be suitable for use in life-support systems or other critical applications where malfunction may cause personal injury. Inclusion of AMIS products in such applications is understood to be fully at the customer’s risk. Applications requiring extended temperature range, operation in unusual environmental conditions, or high reliability, such as military or medical life-support, are specifically not recommended without additional processing by AMIS for such applications. Copyright © 2006 AMI Semiconductor, Inc. AMI Semiconductor – May 06, M-20541-001 www.amis.com 7