a u s t ri a m i c r o s y s t e m s A S 11 5 0 , A S 11 5 1 Q u a d LV D S R e c e i v e r s D a ta S he e t 1 General Description 2 Key Features The AS1150 and AS1151 are quad flow-through LVDS (low-voltage differential signaling) receivers which accept LVDS differential inputs and convert them to LVCMOS outputs. The receivers are perfect for lowpower low-noise applications requiring high signaling rates and reduced EMI emissions. The devices are guaranteed to receive data at speeds up to 500Mbps (250MHz) over controlled impedance media of approximately 100Ω. Supported transmission media are PCB traces, backplanes, and cables. The AS1150 uses high impedance inputs and requires an external termination resistor when used in a point-topoint connection. The AS1151 features integrated parallel termination resistors (nominally 107Ω), which eliminate the requirement for discrete termination resistors, and reduce stub lengths. The integrated failsafe feature sets the output high if the inputs are open, undriven and terminated, or undriven and shorted. Enable inputs (EN and ENn – internally pulled down to GND) control the high-impedance output and are common to all four receivers. All inputs conform to the ANSI TIA/EIA- 644 LVDS standards. Flow-through pinout simplifies PC board layout and reduces crosstalk by separating the LVDS inputs and LVCMOS outputs. ! Flow-Through Pinout ! Guaranteed 500Mbps Data Rate ! 300ps Pulse Skew (Max) ! Conform to ANSI TIA/EIA-644 LVDS Standards ! Single +3.3V Supply ! Operating Temperature Range: -40 to +85ºC ! Failsafe Circuit ! Integrated Termination (AS1151) ! 16-pin TSSOP Package 3 Applications The devices are ideal for digital copiers, laser printers, cellular phone base stations, add/drop muxes, digital cross-connects, dslams, network switches/routers, backplane interconnect, clock distribution computers, intelligent instruments, controllers, critical microprocessors and microcontrollers, power monitoring, and portable/battery-powered equipment. The devices are available in a 16-pin TSSOP package. Figure 1. Block Diagrams VCC IN1+ Rx VCC IN1+ OUT1 IN1- IN2+ Rx IN2+ OUT2 Rx IN3+ OUT3 Rx IN4+ OUT4 IN4- EN EN www.austriamicrosystems.com Rx 107Ω Rx 107Ω Rx OUT2 OUT3 IN3- IN4- ENn 107Ω OUT1 IN2- IN3- IN4+ Rx IN1- IN2- IN3+ 107Ω ENn AS1150 Revision 1.19 OUT4 AS1151 1 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet 4 Absolute Maximum Ratings Stresses beyond those listed in Table 1 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 5 Electrical Characteristics on page 3 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 1. Absolute Maximum Ratings Parameter Min Max Units VCC to GND -0.3 +5.0 V INx+, INx- to GND -0.3 +5.0 V EN, ENn to GND -0.3 VCC + 0.3 V OUTx to GND -0.3 VCC + 0.3 V 750 mW +150 ºC +150 ºC Continuous Power Dissipation (TAMB = +70ºC) Storage Temperature Range -65 Maximum Junction Temperature Notes Derate 9.4mW/°C Above +70°C Operating Temperature Range -40 +85 ºC ESD Protection -4 +4 kV Human Body Model, INx+, INx- ºC The reflow peak soldering temperature (body temperature) specified is in compliance with IPC/JEDEC J-STD-020C “Moisture/ Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices”. Package Body Temperature www.austriamicrosystems.com 260 Revision 1.19 2 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet DC Electrical Characteristics 5 Electrical Characteristics DC Electrical Characteristics VCC = +3.0 to +3.6V, Differential Input Voltage |VID| = 0.1 to 1.0V, Common-Mode Voltage VCM = |VID/2| to 1 2.4V - |VID/2|,TAMB = -40 to +85ºC. Typical values are at VCC = +3.3V, TAMB = +25ºC (unless otherwise specified). Table 2. DC Electrical Characteristics Parameter Symbol Conditions Min Typ Max Unit 100 mV LVDS Inputs (INx+, INx-) Differential Input High Threshold VTH Differential Input Low Threshold VTL Input Current (AS1150) IINx+, IINx- Power-Off Input Current (AS1150) IINOFF -100 mV 0.1V ≤ |VID| ≤ 0.6V -20 20 µA 0.6V ≤ |VID| ≤ 1.0V -25 25 µA 0.1V ≤ |VID| ≤ 0.6V, VCC = 0 -20 20 µA 0.6V ≤ |VID| ≤ 1.0V, VCC = 0 -25 25 µA 1 35 kΩ 1 132 kΩ kΩ Input Resistor 1 (AS1150) RIN1 VCC = 3.6V or 0, Figure 16 on page 9 Input Resistor 2 (AS1150) RIN2 VCC = 3.6V or 0, Figure 16 on page 9 Common Mode Input Resistance RINCM AS1151: Input = 0 150 Differential Input Resistance RDIFF AS1151: VCC = 3.6V or 0, Figure 16 on page 9 90 107 Open, undriven short, or undriven 100Ω parallel termination 2.7 3.2 VID = +100mV 2.7 3.2 Open or Undriven Short 2.7 3.2 VID = +100mV 2.7 132 Ω LVCMOS/LVTTL Outputs (OUTx) Output High Voltage (Table 5) IOH = -4.0mA (AS1150) VOH IOH = -4.0mA (AS1151) Output Low Voltage VOL IOL = +4.0mA, VID = -100mV Output Short-Circuit 2 Current IOS Enabled, VID = 0.1V, VOUTx = 0 Output High-Impedance Current IOZ Disabled, VOUTx = 0 or VCC V 3.2 0.1 0.25 V 15 160 mA -10 10 µA 2.0 VCC V 0 0.8 V -15 15 µA Logic Inputs (EN, ENn) Input High Voltage VIH Input Low Voltage VIL Input Current IIN VINx = VCC or 0 Supply Supply Current ICC Disabled Supply Current ICCZ Enabled, Inputs Open 5 11 average value, |VID| = 200mV 8 15 Disabled, Inputs Open 300 500 mA µA Notes: 1. Current into a pin is defined as positive. Current out of a pin is defined as negative. All voltages are referenced to ground except VTH, VTL, and VID. 2. Short only one output at a time. Do not exceed the absolute maximum junction temperature specification. www.austriamicrosystems.com Revision 1.19 3 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet AC Electrical Characteristics AC Electrical Characteristics VCC = +3.0 to +3.6V, CLOAD = 15pF, Differential Input Voltage |VID| = 0.2 to 1.0V, Common-Mode Voltage VCM = |VID/2| to 2.4V -|VID/2|, Input Rise and Fall Time = 1ns (20 to 80%), Input Frequency = 100MHz, TAMB = -40 to +85ºC. Typical values are at VCC = +3.3V, VCM = 1.2V, |VID| = 0.2V, TAMB = +25ºC (unless otherwise specified). Table 3. AC Electrical Characteristics 1, 2 Parameter Symbol Conditions Min Typ Max Unit Differential Propagation Delay Highto-Low tPHLD Figure 18 on page 11 and Figure 19 on page 12 1.6 2.0 3.1 ns Differential Propagation Delay Lowto-High tPLHD Figure 18 on page 11 and Figure 19 on page 12 1.6 2.0 3.1 ns tSKD1 Figure 18 on page 11 and Figure 19 on page 12 140 300 ps page 12 400 ps Differential Pulse Skew (tPHLD - tPLHD) 3 Differential Channel-to-Channel 4 Skew tSKD2 5 tSKD3 Figure 18 on page 11 and Figure 19 on page 12 0.8 ns 6 tSKD4 Figure 18 on page 11 and Figure 19 on page 12 1.5 ns Rise Time tTLH Figure 18 on page 11 and Figure 19 on page 12 0.5 1.0 ns Fall Time tTHL Figure 18 on page 11 and Figure 19 on page 12 0.5 1.0 ns Disable Time High-to-Z tPHZ RLOAD = 2kΩ, Figure 20 on page 12 and Figure 21 on page 12 14 ns Disable Time Low-to-Z tPLZ RLOAD = 2kΩ, Figure 20 on page 12 and Figure 21 on page 12 14 ns Enable Time Z-to-High tPZH RLOAD = 2kΩ, Figure 20 on page 12 and Figure 21 on page 12 70 ns Enable Time Z-to-Low tPZL RLOAD = 2kΩ, Figure 20 on page 12 and Figure 21 on page 12 70 ns fMAX All Channels Switching Differential Part-to-Part Skew Differential Part-to-Part Skew Maximum Operating Frequency 7, 8 Figure 18 on page 11 and Figure 19 on 250 300 MHz Notes: 1. 2. 3. 4. 5. 6. 7. 8. AC parameters are guaranteed by design and characterization. CL includes scope probe and test jig capacitance. tSKD1 is the magnitude difference of differential propagation delays in a channel. tSKD1 = |tPHLD - tPLHD|. tSKD2 is the magnitude difference of the tPLHD or tPHLD of one channel and the tPLHD or tPHLD of any other channel on the same device. tSKD3 is the magnitude difference of any differential propagation delays between devices operating over rated conditions at the same VCC and within 5ºC of each other. tSKD4 is the magnitude difference of any differential propagation delays between devices operating over rated conditions. fMAX generator output conditions: a. Rise time = fall time = 1ns (0 to 100%) b. 50% duty cycle c. VOH = +1.3V d. VOL = +1.1V Output criteria: a. Duty cycle = 60% to 40% b. VOL = 0.4V (max) c. VOH = 2.7V (min) d. Load = 15pF www.austriamicrosystems.com Revision 1.19 4 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet AC Electrical Characteristics 6 Typical Operating Characteristics VCC = +3.3V, VCM = +1.2V, |VID| = 0.2V, CLOAD = 15pF, TAMB = +25ºC, unless otherwise noted. Figure 2. Supply Current vs. Frequency Figure 3. Supply Current vs. Temperature 14 100 . 80 All Channels Switching Supply Current (mA) Supply Current (mA) . 90 70 60 50 40 30 20 12 Outputs Low 10 8 Outputs High 6 4 2 10 One Channel Switching 0 0,01 0 0,1 1 10 100 -40 1000 -20 Figure 4. Diff. Threshold Voltage vs. VCC 20 40 60 80 100 Figure 5. Output Short-Circuit Current vs. VCC 120 Output Short-Circuit Current (mA) . . 70 Diff. Threshold Voltage (mV) 0 Tem perature (°C) Frequency (MHz) 60 100 High to Low 50 80 40 Low to High 60 30 40 20 20 10 0 0 3 3,1 3,2 3,3 3,4 3,5 3 3,6 3,1 3,2 3,3 3,4 Supply Voltage (V) Supply Voltage (V) Figure 6. Output Low Voltage vs. VCC Figure 7. Output High Voltage vs. VCC 3,6 3,5 3,6 3,7 Output High Voltage (V) . Output Low Voltage (mV) . 110 3,5 109 108 107 106 105 3,5 3,3 3,1 2,9 2,7 3 3,1 3,2 3,3 3,4 3,5 3,6 3 Supply Voltage (V) www.austriamicrosystems.com 3,1 3,2 3,3 3,4 Supply Voltage (V) Revision 1.19 5 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet AC Electrical Characteristics Figure 8. Differential Propagation Delay vs. VCC Figure 9. Differential Propagation Delay vs. Temperature 2,25 Diff. Propagation Delay (ns) Diff. Propagation Delay (ns) . . 2,2 2,16 2,12 tPHLD 2,08 tPLHD 2,04 2,2 2,15 tPLHD 2,1 tPHLD 2,05 2 2 3 3,1 3,2 3,3 3,4 3,5 -45 3,6 -25 Figure 10. Differential Propagation Delay vs. VCM 15 35 55 75 95 Figure 11. Differential Propagation Delay vs. VID 2,3 Diff. Propagation Delay (ns) . . 2,5 Diff. Propagation Delay (ns) -5 Tem perature (°C) Supply Voltage (V) 2,4 2,3 2,2 tPHLD 2,1 tPLHD 2 1,9 -0,5 2,2 2,1 tPHLD 2 tPLHD 1,9 1,8 0 0,5 1 1,5 2 0,1 2,5 Figure 12. Differential Pulse Skew vs. VCC 1,3 1,7 2,1 2,5 . 400 380 Transition Time (ps) . Diff. Pulse Skew (ps) 70 0,9 Figure 13. Transition Time vs. VCC 80 75 0,5 Differential Input Voltage (V) Common-Mode Voltage (V) 65 60 55 50 tTLH 360 tTHL 340 320 45 300 40 3 3,1 3,2 3,3 3,4 3,5 3 3,6 www.austriamicrosystems.com 3,1 3,2 3,3 3,4 3,5 3,6 Supply Voltage (V) Supply Voltage (V) Revision 1.19 6 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet AC Electrical Characteristics Figure 14. Transition Time vs. Temperature . 500 Transition Time (ps) 450 400 tTLH 350 tTHL 300 250 -45 -25 -5 15 35 55 75 95 Tem perature (°C) www.austriamicrosystems.com Revision 1.19 7 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet Pin Assignments 7 Pinout Pin Assignments Figure 15. Pin Assignments (Top View) IN1- 1 16 EN IN1+ 2 15 OUT1 IN2+ 3 14 OUT2 IN2- 4 IN3- 5 IN3+ 6 11 OUT3 IN4+ 7 10 OUT4 IN4- 8 9 ENn AS1150 AS1151 13 VCC 12 GND Pin Descriptions Table 4. Pin Descriptions Pin Number Pin Name 1 IN1- Inverting Differential Receiver Input 2 IN1+ Noninverting Differential Receiver Input 3 IN2+ Noninverting Differential Receiver Input 4 IN2- Inverting Differential Receiver Input 5 IN3- Inverting Differential Receiver Input 6 IN3+ Noninverting Differential Receiver Input 7 IN4+ Noninverting Differential Receiver Input 8 IN4- Inverting Differential Receiver Input 9 ENn Receiver Enable Input. Internally pulled down to GND. When EN = high and ENn = low or open, the receiver outputs are active. For other combinations of EN and ENn, the outputs are disabled and in high impedance. 10 OUT4 LVCMOS/LVTTL Receiver Output 11 OUT3 LVCMOS/LVTTL Receiver Output 12 GND Ground 13 VCC Power-Supply Input. Bypass VCC to GND with 0.1µF and 0.001µF ceramic capacitors. 14 OUT2 LVCMOS/LVTTL Receiver Output 15 OUT1 LVCMOS/LVTTL Receiver Output 16 EN www.austriamicrosystems.com Description Receiver Enable Input. Internally pulled down to GND. When EN = high and ENn = low or open, the receiver outputs are active. For other combinations of EN and ENn, the outputs are disabled and in high impedance. Revision 1.19 8 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet LVDS Interface 8 Detailed Description The AS1150 and AS1151 are 500Mbps, four-channel LVDS receivers intended for high-speed, point-to-point, lowpower applications. Each independent channel accepts and converts an LVDS input to an LVTTL/LVCMOS output. The devices are capable of detecting differential signals from 100mV to 1V within an input voltage range of 0 to 2.4V. The 250 to 450mV differential output of an LVDS driver is nominally centered around 1.25V. Due to the receiver input voltage range, a ±1V voltage shift in the signal relative to the receiver is allowed. Thus, a difference in ground references of the transmitter and the receiver, as well as the common mode effect of coupled noise, can be tolerated. LVDS Interface The LVDS Interface Standard is a signaling method defined for point-to-point communication over a controlled-impedance medium as defined by the ANSI TIA/EIA-644 and IEEE 1596.3 standards. The LVDS standard uses a lower voltage swing than other common communication standards, resulting in higher data rates, reduced power consumption and EMI emissions, and less susceptibility to noise. The devices fully comply with the LVDS standard input voltage range of 0 to +2.4V referenced to receiver ground. The AS1151 has an integrated termination resistors connected internally across each receiver input. This internal termination saves board space, eases layout, and reduces stub length compared to an external termination resistor. In other words, the transmission line is terminated on the IC. Failsafe Circuit The devices contain an integrated failsafe circuit to prevent noise at inputs that are open, undriven and terminated, or undriven and shorted. Open or undriven terminated input conditions can occur if there is a cable failure or when the LVDS driver outputs are high impedance. A short condition also can occur because of a cable failure. The failsafe circuit of the AS1150/AS1151 automatically sets the output high if any of these conditions are true. The failsafe input circuit (see Figure 16) samples the input common-mode voltage and compares it to VCC - 0.3V (nominal). If the input is driven to levels specified in the LVDS standards, the input common-mode voltage is less than VCC 0.3V and the failsafe circuit is not activated. If the inputs are open, undriven and shorted, or undriven and parallel terminated, there is no input current. In this case, a pullup resistor in the failsafe circuit pulls both inputs above VCC - 0.3V, activating the failsafe circuit and thus forcing the device output high. Figure 16. Failsafe Input Circuit VCC VCC RIN2 RIN2 VCC - 0.3V VCC - 0.3V INx+ INx+ RIN1 RIN1 RDIFF OUTx RIN1 OUTx RIN1 INx- INx- AS1150 www.austriamicrosystems.com AS1151 Revision 1.19 9 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet 9 Applications Table 5. Function Table Enable Pins EN Input ENn H Output INx+ L or Open INx- OUTx VID ≥ +100mV H VID ≤ +100mV L AS1150 – Open, undriven short, or undriven 100Ω parallel termination H AS1151 – Open or undriven short Other Combinations of Enable Pin Settings Don’t Care Z Figure 17. Typical Application Circuit LVDS Signals Tx 107Ω Rx Tx 107Ω Rx LVTTL/LVCMOS Data Inputs LVTTL/LVCMOS Data Outputs Tx 107Ω Rx Tx 107Ω Rx AS1151 AS1152 Quad LVDS Driver 100Ω Shielded Twisted Cable or Microstrip PC Board Traces Power-Supply Bypassing To bypass VCC, use high-frequency surface-mount ceramic 0.1µF and 0.001µF capacitors in parallel as close to the device as possible, with the smaller valued capacitor closest to pin VCC. Differential Traces Input trace characteristics can adversely affect the performance of the AS1150 and AS1151. ! Use controlled-impedance PC board traces to match the cable characteristic impedance. The termination resistor must also be matched to this characteristic impedance. ! Eliminate reflections and ensure that noise couples as common mode by running differential traces close together. ! Reduce skew by using matched trace lengths. Tight skew control is required to minimize emissions and proper data recovery of the devices. ! Route each channel’s differential signals very close to each other for optimal cancellation of their respective external magnetic fields. Use a constant distance between the differential traces to avoid irregularities in differential impedance. ! Avoid 90° turns (use two 45° turns). ! Minimize the number of vias to further prevent impedance irregularities. www.austriamicrosystems.com Revision 1.19 10 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet Cables and Connectors Supported transmission media include printed circuit board traces, backplanes, and cables. ! Use cables and connectors with matched differential impedance (typically 100Ω) to minimize impedance mismatches. ! Balanced cables such as twisted pair offer superior signal quality and tend to generate less EMI due to magnetic field canceling effects. Balanced cables pick up noise as common mode, which is rejected by the LVDS receiver. ! Avoid the use of unbalanced cables such as ribbon cable or simple coaxial cable. Termination Due to the high data rates of LVDS drivers, matched termination will prevent the generation of any signal reflections, and reduce EMI. ! The AS1151 has integrated termination resistors connected across the inputs of each receiver. The value of the integrated resistor is specified in Table 2 on page 3. ! The AS1150 requires an external termination resistor. The termination resistor should match the differential impedance of the transmission line and be placed as close to the receiver inputs as possible. Termination resistance values may range between 90 to 132Ω depending on the characteristic impedance of the transmission medium. Use 1% surface-mount resistors. Board Layout The device should be placed as close to the interface connector as possible to minimize LVDS trace length. ! Keep the LVDS and any other digital signals separated from each other to reduce crosstalk. ! Use a four-layer PC board that provides separate power, ground, LVDS signals, and input signals. ! Isolate the input LVDS signals from each other and the output LVCMOS/LVTTL signals from each other to prevent coupling. ! Separate the input LVDS signals from the output signals planes with the power and ground planes for best results. Figure 18. Propagation Delay and Transition Time Test Circuit INx+ Pulse Generator** OUT INx50Ω 50Ω CL Receiver Enabled 1/4 AS1150, AS1151 * 50Ω required for pulse generator. ** When testing the AS1151, adjust the pulse generator output to account for internal termination resistor. www.austriamicrosystems.com Revision 1.19 11 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet Figure 19. Propagation Delay and Transition Time Waveforms INxVID VID = 0 VID = 0 INx+ tPLHD tPHLD VOH VID = (VINx+) - (VINx-) Note: VCM = (VIN- + VIN+) 2 80 80 50% 50% 20 20 OUTx tTLH VOL tTHL Figure 20. High Impedance Delay Test Circuit VCC INx+ Generator INx- EN 50Ω S1 RL Device Under Test OUTx CL ENn CL includes load and test JIG capacitance. S1 = VCC for tPZL and tPLZ measurements. S1 = GND for tPZH and tPHZ measurements. Figure 21. High Impedance Delay Waveforms 3V EN when ENn = GND or Open 1.5V 1.5V 0 3V 1.5V 1.5V 0 ENn when EN = VCC tPZL VCC tPLZ 50% Output when VID = -100mV Output when VID = +100mV 0.5V tPHZ VOL tPZH VOH 0.5V 50% GND www.austriamicrosystems.com Revision 1.19 12 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet Board Layout 10 Package Drawings and Markings Figure 22. 16-Pin TSSOP Package 1, 2 Symbol A A1 A2 L R R1 b b1 c c1 D E1 E 0.65mm Lead Pitch Min Nom Max 1.10 0.05 0.15 0.85 0.90 0.95 0.50 0.60 0.75 0.09 0.09 0.19 0.30 0.19 0.22 0.25 0.09 0.20 0.09 0.16 4.90 4.30 5.00 4.40 6.4 BSC 5.10 4.50 1, 2 Note 5 Symbol θ1 L1 aaa bbb ccc ddd e θ2 θ3 Variations 3, 8 e 4, 8 N 0.65mm Lead Pitch Min Nom Max 0º 8º 1.0 Ref 0.10 0.10 0.05 0.20 0.65 BSC 12º Ref 12º Ref 0.65 BSC 16 Note 6 Notes: 1. All dimensions are in millimeters; angles in degrees. 2. Dimensions and tolerancing per ASME Y14.5M-1994. 3. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15mm per side. 4. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25mm per side. 5. Dimension b does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm total in excess of dimension b at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07mm for 0.5mm pitch packages. 6. Terminal numbers shown are for reference only. 7. Datums A and B to be determined at datum plane H. 8. Dimensions D and E1 to be determined at datum plane H. 9. This dimension applies only to variations with an even number of leads per side. For variations with an odd number of leads per package, the center lead must be coincident with the package centerline, datum A. 10. Cross section A-A to be determined at 0.10 to 0.25mm from the leadtip. www.austriamicrosystems.com Revision 1.19 13 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet Board Layout 11 Ordering Information Model Description Package Type Delivery Form AS1150 Quad low-voltage differential signaling receiver 16-pin TSSOP Tubes AS1150-T Quad low-voltage differential signaling receiver 16-pin TSSOP Tape and Reel AS1151 Quad low-voltage differential signaling receiver with integrated termination 16-pin TSSOP Tubes AS1151-T Quad low-voltage differential signaling receiver with integrated termination 16-pin TSSOP Tape and Reel www.austriamicrosystems.com Revision 1.19 14 - 15 austriam i c r o systems AS1150, AS1151 Data Sheet Board Layout Copyrights Copyright © 1997-2006, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG A-8141 Schloss Premstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com austriamicrosystems www.austriamicrosystems.com Revision 1.19 – a leap ahead 15 - 15