AWT6133 PCS/CDMA 3.5V/29dBm Linear Power Amplifier Module Data Sheet - Rev 2.0 FEATURES • InGaP HBT Technology • High Efficiency: 38% • Low Quiescent Current: 50 mA • Low Leakage Current in Shutdown Mode: <1 µA • VREF = +2.85 V (+2.7 V min over temp) • Optimized for a 50 Ω System • Low Profile Miniature Surface Mount Package: 1.56 mm Max • CDMA 1XRTT Compliant • CDMA 1xEV-DO Compliant APPLICATIONS • PCS CDMA Wireless Handsets • Dual Band CDMA Wireless Handsets M7 Package 10 Pin 4 mm x 4 mm x 1.5 mm Surface Mount Module PRODUCT DESCRIPTION The AWT6133 meets the increasing demands for higher efficiency and linearity in CDMA 1XRTT handsets. The PA module is optimized for VREF = +2.85 V, a requirement for compatibility with the Qualcomm® 6000 chipset. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. The self-contained 4 mm x 4 mm x 1.5 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. GND at slug (pad) VCC 1 10 VCC RFIN 2 9 GND GND 3 8 RFOUT 7 GND 6 GND VMODE 4 Bias Control VREF 5 Figure 1: Block Diagram 12/2004 AWT6133 GND VCC 1 10 VCC RFIN 2 9 GND GND 3 8 RFOUT VMODE 4 7 GND VREF 5 6 GND GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 V CC Supply Voltage 2 RFIN RF Input 3 GND Ground 4 VMODE Mode Control Voltage 5 VREF Reference Voltage 6 GND Ground 7 GND Ground 8 RFOUT RF Output 9 GND Ground 10 V CC Supply Voltage Data Sheet - Rev 2.0 12/2004 AWT6133 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) DC Only RF Drive < +5 dBm 0 0 +8 +6(1) V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dB m -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: (1) VSWR < 2:1. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 1850 - 1910 MHz Supply Voltage (VCC) +3.2 +3.5 +4.2 V Reference Voltage (VREF) +2.7 0 +2.85 - +2.9 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.85 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) +28.5(1) +29.0 - dB m Case Temperature (TC) -30 - +85 °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at TC = +85 °C and VCC = +3.2 V, POUT is derated by 0.5 dB. Data Sheet - Rev 2.0 12/2004 3 AWT6133 Table 4: Electrical Specifications (TC = +25 °C, VCC = +3.5 V, VREF = +2.85 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT COMMENTS 25 22 27 24.5 30 27 dB POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Adjacent Channel Power (1) at 61.25 MHz offset Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -49 -50 -47 -47 dB c POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Adjacent Channel Power at 62.25 MHz offset Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz - -60 -65 -57 -57 dB c POUT = +29 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V 36 7.25 38 8 - % POUT = +29.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V Quiescent Current (Icq) - 110 50 125 65 mA VMODE = 0 V VMODE = +2.85 V Reference Current - 3.7 5 mA through VREF pin, PA on Mode Control Current - 0.3 0.5 mA through VMODE pin, VMODE = +2.85 V Leakage Current - <1 5 mA VCC = +4.2 V, VREF = 0 V VMODE = 0 V Noise in Receive Band 1930 MHz to 1990 MHz - -136 -134 dBm/Hz Harmonics 2fo 3fo, 4fo - -45 -55 -30 -30 dB c Input Impedance - - 2:1 VSWR Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure - - -65 dB c 8:1 - - VSWR Notes: (1) ACPR and PAE limits apply to middle frequency only. 4 Data Sheet - Rev 2.0 12/2004 POUT [ +29 dBm In-band load VSWR < 8:1 Out-of-band load VSWR 8:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range AWT6133 APPLICATION INFORMATION Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Table 5: Bias Control APPLICATION POUT LE V E LS BIAS MODE CDMA - low power <+16dBm Low +2.85 V +2.85 V CDMA - high power >+16 dBm High +2.85 V 0V - Shutdown 0V 0V Shutdown V R EF VCC1 VMODE VCC2 C1 0.01µF C3 0.01µF RF IN VMODE VREF C2 0.01µF 1 VCC 2 VCC 10 3 RFIN GND 9 GND RFOUT 8 4 VMODE GND 7 5 VREF GND 6 C4 2.2µF ceramic RF OUT GND at slug Figure 3: Application Circuit Schematic Data Sheet - Rev 2.0 12/2004 5 AWT6133 PACKAGE OUTLINE Figure 4: M7 Package Outline - 10 Pin 4 mm x 4 mm x 1.5 mm Surface Mount Module AWT6133 AWT6133 BBB LASER MARKED Figure 5: Branding Specification 6 Data Sheet - Rev 2.0 12/2004 AWT6133 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 4 mm x 4 mm x 1.5 mm 12 mm 8 mm 2500 13" Data Sheet - Rev 2.0 12/2004 7 AWT6133 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWT6133M7P8 -30 oC to +85 oC 10 P i n 4 mm x 4 mm x 1.5 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.0 12/2004