ANADIGICS AWT6132RM5P8

AWT6132R
415 MHz CDMA 3.4V/29.5dBm
Linear Power Amplifier Module
Data Sheet - Rev 2.1
FEATURES
• InGaP HBT Technology
• High Efficiency 35 % CDMA
• Low Leakage Current (<5 µA)
• SMT Module Package
• 50 Ω Input and Output Matching
AW
T
613
• Shut Down and Mode Control
• CDMA 2000 1XRTT Compliant
2R
• RoHS Compliant Package, 250 oC MSL-3
APPLICATIONS
• CDMA/EVDO 415 MHz Wireless Handsets and
Data Devices
M5 Package
7 Pin 6 mm x 6 mm x 1.5 mm
Surface Mount Module
PRODUCT DESCRIPTION
The AWT6132R is a high power, high efficiency
amplifier module for CDMA wireless handset
applications. The device is manufactured on an
advanced InGaP HBT MMIC technology offering
state-of-the-art reliability, temperature stability and
ruggedness. A low power mode is available to reduce
power drain on the system battery. The 6 mm x 6
mm x 1.5 mm laminate package is self contained,
incorporating 50 Ω input and output matching networks
optimized for output power, linearity, and efficiency.
Figure 1: Block Diagram
10/2008
AWT6132R
GND
VCC
1
7
GND
RFIN
2
6
RFOUT
VREF
3
5
VCC
4
VMODE
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
2
PIN
NAME
DESCRIPTION
1
VCC
Supply Voltage
2
RFIN
RF Input Signal
3
VREF
Reference Voltage
4
VMODE
Mode Control
5
VCC
Supply Voltage
6
RFOUT
RF Output
7
GND
Ground
MASTER DATA SHEET - Rev 2.1
10/2008
AWT6132R
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
MAX
UNIT
Supply Voltage (VCC )
0
+5
V
Mode Control Voltage (VMODE)
0
+3.4
V
Reference Voltage (VREF)
0
+3.4
V
RF Input Power (PIN)
-
+10
dBm
-40
+150
°C
Storage Temperature (TSTG)
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
PARAMETER
MIN
TYP
MAX
UNIT
Operating Frequency (f)
410
-
420
MHz
Supply Voltage (VCC)
+3.2
+3.4
+4.2
V
Reference Voltage (VREF)
+2.80
0
+2.90
-
+3.1
+0.5
V
PA"on"
PA"shut down"
Mode Control Voltage (VMODE)
+2.5
0
+2.90
-
+3.1
+0.5
V
Low Bias Mode
High Bias Mode
RF Output Power (POUT)
+29.0 (1)
+29.5
-
dBm
Case Temperature (TC)
-30
-
+90
o
COMMENTS
CDMA, VCC =+3.4V
C
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Notes:
(1) For operation at Vcc = +3.2 V , POUT is derated by 0.5 dB.
MASTER DATA SHEET - Rev 2.1
10/2008
3
AWT6132R
Table 4: Electrical Specifications – CDMA Operation
(TC = +25 OC, VCC = +3.4 V, VREF = +2.90 V, 50 Ω system)
TYP
MAX
UNIT
26
25
28
27
31
29
dB
Gain Variation
-
0.4
1.0
dB
Adjacent Channel Power
at 885 kHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-52
-57
-46.5
-47
dB
POUT = +29.5 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.90 V
Adjacent Channel Power
at 1.98 MHz offset (1)
Primary Channel BW = 1.23 MHZ
Adjacent Channel BW = 30 kHz
-
-62
-67
-59
-59
dB
POUT = +29.5 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.90 V
33
6
35
7
-
%
POUT = +29.5 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.90 V
Quiescent Current (Icq)
-
60
80
mA
through VCC pins, VMODE = +2.90 V
Reference Current
-
6.5
9
mA
through VREF pin, PA "on"
Mode Control Current
-
0.8
1.0
mA
through VMODE pin,
VMODE = +2.90 V
Leakage Current
-
<1
5
A
VCC = +4.2 V, VREF = 0 V,
VMODE = 0 V
Noise in Receive Band
-
-132
-130
dBm/Hz
Harmonics
2fo
3fo, 4fo
-
-36
-45
-30
-35
dBc
Input Impedance
-
-
2:1
VSWR
Gain
Power-Added Efficiency (1)
Spurious Output Level
(all spurious outputs)
Load mismatch stress with no
permanent degradation or failure
POUT = +29.5 dBm, VMODE = 0 V
POUT = +16 dBm, VMODE = +2.90 V
fO +10 MHz, POUT < +29.5 dBm
POUT < +29.5 dBm
-
-
-70
dBc
POUT < +29.5 dBm
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating ranges
10:1
-
-
VSWR
Applies over all operating ranges
Notes:
(1) POUT is derated by 0.5 dB for IS-98 / CDMA 2000 operation.
(2) ACPR and Efficiency Measured at 415 MHz.
4
COMMENTS
MIN
PARAMETER
MASTER DATA SHEET - Rev 2.1
10/2008
AWT6132R
APPLICATION INFORMATION
High Bias Mode
The power amplifier may be placed in a high bias mode
by applying a logic low level (see Operating Ranges
table) to the VMODE voltage.
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to both the VREF and VMODE voltages.
GND at slug (pad)
VCC
1
7
GND
4.7uF
(ceramic)
RF Input
RF Out
(50 Ohms)
(50 Ohms)
2
6
Bias Control
VREF
3
4
VCC
5
0.1uF
4.7uF (ceramic)
VMODE
Figure 3: Application Circuit Schematic
MASTER DATA SHEET - Rev 2.1
10/2008
5
AWT6132R
PACKAGE OUTLINE
Figure 4: M5 Package Outline - 7 Pin 6 x 6 x 1.5 mm Surface Mount Module (Low Band )
Figure 5: Branding Specification
6
MASTER DATA SHEET - Rev 2.1
10/2008
AWT6132R
COMPONENT PACKAGING
Figure 6: Tape & Reel Packaging
Table 5: Tape & Reel Dimensions
PACKAGE TYPE
TAPE WIDTH
POCKET PITCH
REEL CAPACITY
MAX REEL DIA
6 mm x 6 mm x 1.5 mm
12 mm
8 mm
2500
13"
MASTER DATA SHEET - Rev 2.1
10/2008
7
AWT6132R
Ordering Information
ORDER NUMBER
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
COMPONENT PACKAGING
AWT6132RM5P8
-30 oC to +90 oC
RoHS Compliant 7 Pin
6 mm x 6 mm x 1.5 mm
Surface Mount Module
Tape and Reel, 2500 pieces per Reel
AWT6132RM5P9
-30 oC to +90 oC
RoHS Compliant 7 Pin
6 mm x 6 mm x 1.5 mm
Surface Mount Module
Partial Tape and Reel
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: [email protected]
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to
verify that the information they are using is current before placing orders.
warning
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product
in any such application without written consent is prohibited.
8
MASTER DATA SHEET - Rev 2.1
10/2008