SIL40C2 Series 4.5-13.8 Vin Single Output DC-DC CONVERTERS C Class Non-isolated March 15, 2006 1 NEW Product •40 A current rating •Input voltage range: 4.5-13.8 V •Output voltage: 0.6-5 V •Industry leading value • Cost optimized design •Excellent transient response •Output enable •Output voltage adjustability • Pathway for future upgrades • Supports silicon voltage migration • Resulting in reduced design-in and qual time •RoHS compliant The SIL40C2 series is a new high density open frame non-isolated converter for space sensitive applications. This model has a wide input range (4.5-13.8 Vdc) and offers a wide 0.6-5 V output voltage range with 40 A load capability. An external resistor adjusts the output voltage from its pre-set value of 0.6 V to any value up to the 5 V maximum. Typical efficiencies for the models are 91% for the 12 V input version. The SIL40C2 series offers remote ON/OFF and over-current protection as standard. 2 year warranty All specifications are typical at nominal input, full load at 25 °C unless otherwise stated SPECIFICATIONS GENERAL SPECIFICATIONS OUTPUT SPECIFICATIONS Output voltage (See Note 5) 0.6-5 V Efficiency Vin=5 V, Vo=2.5 V, lo=20 A Output setpoint accuracy 0.1% trim resistors ±1.0% Switching frequency Fixed Line regulation Low line to high line ±0.2% Approvals and standards (pending) Load regulation Full load to min. load ±0.5% Material flammability Min/max load Overshoot 0 A/40 A At turn-on 0.5% max. Undershoot At turn-off 100 mV max. Ripple and noise 5 Hz to 20 MHz (See Note 1) Transient response (See Notes 1, 2) 25 mV Vin = 5 V, Vout = 2.5 V 150 mV max. deviation 30 µs recovery within regulation band INPUT SPECIFICATIONS Input voltage range 500 kHz EN60950 UL/cUL60950 UL94V-0 17 g/0.06 oz. Weight MTBF 94% Typ. 12 V @ 40 °C 100% load Bellcore 332 6,749,409 hours Coplanarity 150 µm ENVIRONMENTAL SPECIFICATIONS Thermal performance (See Note 5) Operating ambient, temperature Non-operating 0 °C to +70 °C -40 °C to +125 °C 4.5-13.8 Vdc Input current Minimum load Remote OFF Input current (max.) (See Note 3) Start-up time Remote ON/OFF 50 mA 5 mA 25 A @ Io max. PROTECTION Short-circuit Hiccup, non-latching Over voltage Hiccup, non-latching 3 ms RECOMMENDED SYSTEM CAPACITANCE International Safety Standard Approvals Input capacitance (See Note 6) 0 µF Output capacitance (See Note 7) 0 µF UL/cUL CAN/CSA 22.2 No. E139421 UL60950 File No. TBD TÜV Product Service (EN60950) Certificate No. TBD CB report and certificate to IEC60950 File Name: sil40c2.pdf Rev: 15 Mar 2006 SIL40C2 Series 4.5-13.8 Vin Single Output DC-DC CONVERTERS March 15, 2006 C Class Non-isolated 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT INPUT OUTPUT POWER OVP VOLTAGE VOLTAGE (MAX.) 200 W 4.5-13.8 Vdc N/A 0.6-5 Vdc Part Number System with Options NEW Product OUTPUT CURRENT (MIN.) OUTPUT CURRENT (MAX.) EFFICIENCY (TYP.) REGULATION LINE 0A 40 A 94% ±0.2% MODEL NUMBER (8, 9) LOAD ±0.5% SIL40C2-00SADJ-VJ SIL40C2-00SADJ-VJ RoHS Compliance (8) J = Pb-free (RoHS 6/6 compliant) Product Family SIL = Single In Line SMT = Surface Mount Mounting Option V = Vertical H = Horizontal Rated Output Current 06 = 6 A 15 = 15 A 20 = 20 A 30 = 30 A 40 = 40 A Output Voltage Single Adjustable Output Input Voltage 00 = 4.5-13.8 V Performance C = Cost Optimized Generation Blank = Standard Part 2 = Increased Current Density Output Voltage Adjustment of the SIL40C2 Ser ies The ultra-wide output voltage trim range offers major advantages to users who select the SIL40C2. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.6-5 V. When the SIL40C2 converter leaves the factory the ouput has been adjusted to the default voltage of 0.6 V. Notes 1 Measured as per recommended system capacitance. 2 di/dt = 10 A/µs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75. 3 External input fusing is recommended. 4 Additional part numbers may be available with different output voltages. 5 Airflow dependent, 100 LFM minimum required. 6 No capacitor needed for ripple current capability. 7 No capacitor needed for stability. 8 TSE RoHS 5/6 (non PB-free) compliant versions are also available on special request, please contact your local sales representative for details. 9 NOTICE: Some models may not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/ products.htm to find a suitable alternative. Power Good 6 Enable 5 Vout 1,2,3 9 +Rsense SIL40C2 Vin 10,11 7,8 Cout 4 Cin R L O A D Rtrim (for trim down) GND Figure 1: Standard Application Drawing File Name: sil40c2.pdf Rev: 15 Mar 2006 SIL40C2 Series 4.5-13.8 Vin Single Output DC-DC CONVERTERS C Class Non-isolated March 15, 2006 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product 1.200 (30.48) 0.427 (10.85) 0.255 (6.48) 1.100 (27.94) 0.062 (1.57) REF 0.110 (2.79) 0.050 (1.27) REF PIN 1 0.140 (3.56) TYP 0.100 (2.54) 0.100 (2.54) TYP 9 PLACES 1.050 (26.67) PIN CONNECTIONS PIN NO. FUNCTION 1 Vout 2 Vout 3 Vout 4 Trim 5 Enable 6 Power Good 7 Ground 8 Ground 9 (+) Sense 0.468 (11.89) 10 Vin 0.255 (6.48) 11 Vin 12 *Mech Support 13 *Mech Support 0.050 (1.27) TYP Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 0.025 (0.64) ±.001 SQ PINS TYP Figure 2: Vertical Mount Mechanical Drawing 1.200 (30.48) 0.062 (1.57) REF 1.100 (27.94) .150 (3.81) TYP PIN 1 0.110 (2.79) REF * Horizontal and SMT version only 0.120 (3.05) TYP 0.100 (2.54) TYP 9 PLACES Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 2X 1.000 (25.40) 0.025 (0.64) ±.001 SQ PINS TYP 13 PLACES 0.050 (1.27) REF 2X 1.050 (26.67) 0.050 (1.27) 0.100 (2.54) REF Figure 3: Horizontal Mount Mechanical Drawing File Name: sil40c2.pdf Rev: 15 Mar 2006 SIL40C2 Series 4.5-13.8 Vin Single Output DC-DC CONVERTERS C Class Non-isolated March 15, 2006 4 For the most current data and application support visit www.artesyn.com/powergroup/products.htm PIN CONNECTIONS PIN NO. FUNCTION 1 Vout 2 Vout 3 Vout 4 Trim 5 Enable 6 Power Good 7 Ground 8 Ground 9 (+) Sense 10 Vin 11 Vin 12 *Mech Support 13 *Mech Support NEW Product 1.200 (30.48) 0.442 (11.23) 0.062 (1.57) REF 0.255 (6.48) 0.110 (2.79) REF 0.125 (3.18) TYP 1.100 (27.94) PIN 1 2X 1.000 (25.40) 0.050 (1.27) REF 0.100 (2.54) TYP 9 PLACES Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 2X 1.050 (26.67) 0.050 (1.27) 0.100 (2.54) REF Figure 4: Surface Mount Mechanical Drawing * Horizontal and SMT version only Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: Application Note Longform Datasheet www.artesyn.com File Name: sil40c2.pdf Rev: 15 Mar 2006