Issue: 01 Date: 2006-07-11 Specification AXIS45 Oscillator type : Wideband VCXO in double-sealed DIL package Direct replacement of Fujitsu M2 (F100) Parameter min. max. Unit Frequency range Standard frequencies 5 30 16.384 / 24.576 / 27.000 / 28.224 MHz MHz Frequency stability Initial tolerance vs. temperature in operating temperature range vs. supply voltage variation vs. load change long term (aging) Frequency adjustment range Electronic Frequency Control (EFC) (Pulling range) See Note 2 EFC voltage VC EFC slope (∆f / ∆VC) EFC linearity EFC input impedance RF output Signal waveform Load Rise & decay time Symmetry (duty cycle) Start-up time Supply voltage VS typ. ppm ppm ppm ± 100 ± 500 ± 1000 ± 1500* ± 2000* ± 2500* ± 3000* 0.25 0.15 Condition -20°C ~+70°C ± 10 ±5 ± 10 ppm ppm ppm/year @ 40°C 4.75 3.15 ppm ppm ppm ppm ppm ppm V v Option 2 = “ ” Option 2 = “1000” Option 2 = “1500” * Option 2 = “2000” * Option 2 = “2500” * Option 2 = “3000” * Option 1 = “50“ (5 V) Option 1 = “33” (3.3 V) positive % kΩ 100 HCMOS 15 Current consumption Operating temperature range Operable temperature range Storage temperature range Enclosure (see drawing) LxWxH Weight Packing ESD Sensitivity RoHS compliance 10 40 60 4 4.75 5.0 5.25 3.13 3.3 3.47 30 -20 +70 -40 +85 -45 +90 20.7x13.1x7.5 max. 3 sticks 1500 Full pF ns % ms V V mA °C °C °C mm gram V @ VS/2 Option 1 = “50“ (5 V) Option 1 = “33” (3.3 V) @ +25°C IEC 60679-3 CO 02 IEC 60286-3 HBM, IEC 61000-4-2 Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated 2. *Pulling Range Option 3 > 1000 only possible with EFC voltage 0.25V ~ 4.75 V Ordering Code: Model (Specification) AXIS45 GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany Option 1 Supply 50 Option 2 Pulling Range 2000 AXIS45 page 1(2) Frequency [MHz] 28.224 www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Enclosure drawing Pin connections Pin # 1 7 8 14 Symbol VC GND RF OUT VS Function Control Voltage (EFC) Ground RF Output Supply Voltage Environmental conditions Test IEC 60068 Part ... Visual inspection, dimensions Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60679-1 clause ... 4.3 2-17 4.6.2 2-20 2-58 4.6.3 2-27 4.6.8 Bump* 2-29 4.6.6 Free fall* 2-32 4.6.9 Test conditions Enclosure styles as in IEC 60679-3 or 61837, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Vibration, sinusoidal* 2-6 4.6.7 Rapid change of temperature Dry heat 2-14 4.6.5 2-2 4.6.14 Damp heat, cyclic* 2-30 4.6.15 Cold 2-1 4.6.16 Climatic sequence* 1-7 4.6.17 Damp heat, steady state* Endurance tests - ageing - extended aging 2-3 4.6.18 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.6.14, 4.6.15 (1st cycle), 4.6.16, 4.6.15 (5 cycles) Test Ca, 56 days 4.7.1 4.7.2 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXIS45 page 2(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]