rev. date 08/2007 features · isolated 1 Designed to convert fixed voltages into an isolated voltage, the VASD1-SIP series is well suited for providing board-mount local supplies in a wide range of applications, including mixed analog/digital circuits, test & measurement equip., process/machine controls, datacom/telecom fields, etc... The semi-regulated output can be followed by 3-terminal regulators to provide output protection, in addition to output regulation. model number VASD1-S5-D5-SIP VASD1-S5-D9-SIP VASD1-S5-D12-SIP VASD1-S5-D15-SIP VASD1-S12-D5-SIP VASD1-S12-D9-SIP VASD1-S12-D12-SIP VASD1-S12-D15-SIP VASD1-S15-D5-SIP VASD1-S15-D9-SIP VASD1-S15-D12-SIP VASD1-S15-D15-SIP VASD1-S24-D5-SIP VASD1-S24-D9-SIP VASD1-S24-D12-SIP VASD1-S24-D15-SIP 1 of 3 DESCRIPTION: DC/DC converter PART NUMBER: VASD1-SIP series description page W output ·temperature range: -40°C~+85°C ·unregulated ·high efficiency to 80% ·dual voltage output ·small footprint ·DIP package style ·industry standard pinout ·UL94-V0 package ·no heatsink required ·1K Vdc isolation ·power density 0.85 W/cm³ ·no external component required ·low cost input voltage nominal range 5 Vdc 4.5~5.5 Vdc 5 Vdc 4.5~5.5 Vdc 5 Vdc 4.5~5.5 Vdc 5 Vdc 4.5~5.5 Vdc 12 Vdc 10.8~13.2 Vdc 12 Vdc 10.8~13.2 Vdc 12 Vdc 10.8~13.2 Vdc 12 Vdc 10.8~13.2 Vdc 15 Vdc 13.5~16.5 Vdc 15 Vdc 13.5~16.5 Vdc 15 Vdc 13.5~16.5 Vdc 15 Vdc 13.5~16.5 Vdc 24 Vdc 21.6~26.4 Vdc 24 Vdc 21.6~26.4 Vdc 24 Vdc 21.6~26.4 Vdc 24 Vdc 21.6~26.4 Vdc output voltage ±5 Vdc ±9 Vdc ±12 Vdc ±15 Vdc ±5 Vdc ±9 Vdc ±12 Vdc ±15 Vdc ±5 Vdc ±9 Vdc ±12 Vdc ±15 Vdc ±5 Vdc ±9 Vdc ±12 Vdc ±15 Vdc output current max. min. ±100 mA ±10 mA ±56 mA ±6 mA ±42 mA ±5 mA ±33 mA ±4 mA ±100 mA ±10 mA ±56 mA ±6 mA ±42 mA ±5 mA ±33 mA ±4 mA ±100 mA ±10 mA ±56 mA ±6A ±42 mA ±5 mA ±33 mA ±4 mA ±100 mA ±10 mA ±56 mA ±6 mA ±42 mA ±5 mA ±33 mA ±4 mA package style SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP SIP efficiency 72% 75% 78% 79% 74% 76% 79% 80% 74% 75% 79% 79% 74% 76% 80% 81% OUTPUT SPECIFICATIONS item output power line regulation load regulation output voltage accuracy temperature drift output ripple switching frequency test conditions for Vin change of 1% 10% to 100% full load see tolerance envelope graph @ 100% load 20 MHz Bandwidth full load, nominal input min. 0.1 typ. 10 50 100 max. 1 1.2 15 units W % % 0.03 75 %/°C mVp-p KHz NOTE: 1. All specifications measured at TA=25°C, humidity <75%, nominal input voltage and rated output load unless otherwise specified. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 UL60950-1 YES YES YES YES YES YES YES YES NO NO NO NO YES YES YES YES rev. page 2 of 3 date 08/2007 DESCRIPTION: DC/DC converter PART NUMBER: VASD1-SIP series GENERAL SPECIFICATIONS short circuit protection temperature rise at full load <1 second 25°C Max, 15°C typ. cooling free air convection operating temperature range -40°C to +85°C storage temperature range -55°C to +125°C soldering temperature 300°C (1.5mm from case for 10 sec.) storage humidity range <95% case material plastic (UL94-V0) safety approved to UL60950-1 (E222736) MTBF >3,500,000 hrs. burn-in full load at +85°C, for 4 hours at no-load and 4 hours at full load. ISOLATION SPECIFICATIONS item isolation voltage insulation resistance test conditions tested for 1 min. test at 500 Vdc DIMENSIONS (mm) min. 1000 1000 typ. max units Vdc M Ω TYPICAL CHARACTERISTICS Pin 1 2 4 5 6 +Vin -Vin -Vout COM +Vout 1 2 4 5 6 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 rev. page 3 of 3 date 08/2007 DESCRIPTION: DC/DC converter PART NUMBER: VASD1-SIP series - Minimum loading APPLICATION NOTES: The converter needs a minimum of 10% loading to maintain output regulation. Operation under no-load conditions will not - Input filtering To reduce the reflected ripple current and minimize EMI, cause immediate damages but may reduce reliability, and especially when the converter input is more than 2” away from cause performance not to meet specifications. the DC source, it is recommended to connect a low ESR electrolytic capacitor between Vin and Gnd. The values - Regulation suggested are as shown in Table 1. If additional filtering is With a semi-regulated design, the converter’s output voltage required, the capacitance may be increased, or expanded to varies with load current and will change proportionally to the an LC network as shown in Figure 1. input voltage. If regulated output is needed, an external regulator can be used as shown in Figure 2. TABLE 1 - Protection Input Voltage External Input Capacitance 5V 4.7 µF 12 V 2.2 µF 15 V 2.2 µF 24 V 1.0 µF The converter has minimal protection against input overvoltage or output over-load, and may be permanently damaged if exposed to these conditions. An input clamping device can be used for input voltage limiting. An input fuse or an output fuse also be used to protect against over-loading. - Dual outputs used as a single output The +Vout and -Vout can be used to obtain a single output that is the sum of the two outputs. In this case, the COM pin - Output filtering shouldn’t be used. An output capacitor is needed to meet output ripple requirements as shown in Table 2.Output capacitance may be - External Regulator increased for additional filtering, but should not exeed 10µF or An external 3-terminal regulator can be connected to the expanded to an LC network as in Figure 1. output of the converter to achieve full regulation. Make sure the converter’s output voltage provides sufficient head room for the regulator. An additional benefit is that the built-in TABLE 2 protection features in the regulator, such as OCP, OTP, etc, will protect the converter also. In a complimentory supply, a Vout External Ouput Capacitance 5V 4.7 µF 9V 2.2 µF 12 V 1.0 µF +Vin 15 V 0.47 µF -Vin 24 V 0.33 µF negative output regulator must be used to achieve the negative regulated output. +Vout REG DC DC COM -Vout +Vin REG +Vout REG -Vout DC DC -Vin L L +Vout +Vin C C DC DC -Vin COM L C -Vout <Figure 1> 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2382 COM