DS1626/DS1726 High-Precision 3-Wire Digital Thermometer and Thermostat www.maxim-ic.com FEATURES PIN CONFIGURATION Temperature Measurements Require No External Components Measure Temperatures from -55°C to +125°C (-67°F to +257°F) DS1626: ±0.5°C Accuracy from 0°C to +70°C DS1726: ±1°C Accuracy from -10°C to +85°C Output Resolution is User-Selectable to 9, 10, 11, or 12 Bits Wide Power-Supply Range (2.7V to 5.5V) Convert Temperature to Digital Word in 750ms (max) Stand-Alone Thermostat Capability Thermostatic Settings are User-Definable and Nonvolatile (NV) Data is Read/Written Through a 3-Wire Serial Interface Available in 8-Pin μMAX/μSOP Package 8 VDD 2 7 THIGH 3 6 TLOW 5 TCOM DQ 1 CLK/CNV RST GND 4 μSOP (DS1626U, DS1726U) See Table 1 for Ordering Information See Table 2 for Pin Descriptions APPLICATIONS Thermostatic Controls Industrial Controls Consumer Products Any Space-Constrained Thermally Sensitive Application DESCRIPTION The DS1626 and DS1726 digital thermometers/thermostats provide temperature measurements and standalone thermostat capability over a -55°C to +125°C range. The DS1626 offers ±0.5°C accuracy from 0°C to +70°C and the DS1726 has ±1°C accuracy from -10°C to +85°C. The resolution of the measured temperature is user-selectable from 9 to 12 bits. Communication with the DS1626 and DS1726 is achieved through a 3-wire serial bus. The DS1626 and DS1726 offer thermostatic functionality with three dedicated thermostat outputs (THIGH, TLOW, and TCOM), and over-temperature (TH) and under-temperature (TL) user-programmable thresholds stored in on-chip EEPROM. For stand-alone thermostat operation, TH and TL can be programmed prior to installation, and the DS1626/DS1726 can be configured to automatically begin taking temperature measurements at power-up. Pin descriptions for the DS1626 and DS1726 are provided in Table 2 and user-accessible registers are summarized in Table 3. A functional diagram is shown in Figure 1. 1 of 14 071107 DS1626/DS1726 ORDERING INFORMATION PART DS1626U DS1626U+ DS1626U/T&R DS1626U+T&R DS1726U DS1726U+ DS1726U/T&R DS1726U+T&R PACKAGE MARKING 1626 1626 (See Note) 1626 1626 (See Note) 1726 1726 (See Note) 1726 1726 (See Note) DESCRIPTION 8-Pin μSOP Lead-Free 8-Pin μSOP 8-Pin μSOP, 3000-Piece Tape-and-Reel Lead-Free 8-Pin μSOP, 3000-Piece Tape-and-Reel 8-Pin μSOP Lead-Free 8-Pin μSOP 8-Pin μSOP, 3000-Piece Tape-and-Reel Lead-Free 8-Pin μSOP, 3000-Piece Tape-and-Reel Note: A “+” symbol will also be marked on the package near the Pin 1 indicator. Table 2. DETAILED PIN DESCRIPTION PIN 1 SYMBOL DQ 2 CLK/CNV 3 4 5 6 7 8 RST GND TCOM TLOW THIGH VDD FUNCTION Data Input/Output Pin (Tri-State) for 3-Wire Serial Communication Clock Input Pin for 3-Wire Serial Communication. Controls temperature measurements when the DS1626/DS1726 is configured as a stand-alone thermostat Reset Input Pin for 3-Wire Serial Communication Ground Pin Thermostat Output Pin (Push-Pull) with Programmable Hysteresis Thermostat Output Pin (Push-Pull) with TL Trip Point Thermostat Output Pin (Push-Pull) with TH Trip Point Supply Voltage. +2.7V to +5.5V Input Power Pin Table 3. DS1626/DS1726 REGISTER SUMMARY REGISTER NAME (USER ACCESS) Temperature (Read Only) SIZE MEMORY TYPE 12 Bits SRAM TH (Read/Write) 12 Bits EEPROM TL (Read/Write) 12 Bits EEPROM Configuration (Various Bits are Read/Write and Read Only—See Table 5) 1 Byte SRAM and EEPROM REGISTER CONTENTS AND POWER-UP/POR STATE Measured Temperature (Two’s Complement) Power-Up/POR State: -60ºC (1100 0100 0000) Upper Alarm Trip Point (Two’s Complement) Power-Up/POR State: User-Defined. Initial State from Factory: +15°C (0000 1111 0000) Lower Alarm Trip Point (Two’s Complement) Power-Up/POR State: User-Defined. Initial State from Factory: +10°C (0000 1010 0000) Configuration and Status Information (Unsigned) 4MSbs = SRAM and 4LSbs = EEPROM Power-Up/POR State: 1000XXXX (XXXX = UserDefined) Figure 1. DS1626/DS1726 FUNCTIONAL DIAGRAM VDD CONFIGURATION REGISTER AND CONTROL LOGIC GND TEMPERATURE SENSOR AND ΔΣ ADC ADDRESS and I/O CONTROL CLK/CNV SDA RST TEMPERATURE REGISTER 2 of 14 TH REGISTER DIGITAL COMPARATOR/LOGIC TCOM THIGH TLOW DS1626/DS1726 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Range Storage Temperature Range Solder Dip Temperature (10s) Reflow Oven Temperature -0.5V to +6.0V -55°C to +125°C -55°C to +125°C +260°C +220°C * These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. DC ELECTRICAL CHARACTERISTICS (VDD = 2.7V to 5.5V; TA = -55°C to +125°C.) PARAMETER Supply Voltage DS1626 Thermometer Error (Note 2) DS1726 Thermometer Error (Note 2) Low-Level Input Voltage High-Level Input Voltage Input Current each Input Pin Active Supply Current (Note 3) Input Resistance Standby Supply Current THIGH, TLOW, SYMBOL VDD CONDITIONS (Note 1) 0°C to +70°C, 3.0V ≤ VDD ≤ 5.5V 0°C to +70°C, 2.7V ≤ VDD < 3.0V -55°C to +125°C -10°C to +85°C, 3.0V ≤ VDD ≤ 5.5V -10°C to +85°C, 2.7V ≤ VDD < 3.0V -55°C to +125°C MIN 2.7 VIL (Note 1) -0.5 0.3 x VDD V VIH (Note 1) 0.7 x VDD VDD + 0.3 V -10 +10 µA TERR TERR 0.4 < VI/O < 0.9 x VDD IDD RI Temperature conversion -55°C to +85°C Temperature conversion +85°C to +125°C E2 write RST to GND DQ, CLK to VDD ISTBY 0°C to +70°C (Note 3) VOH 1mA source current 3 of 14 TYP MAX 5.5 UNITS V ±0.5 ±1.25 °C ±2 ±1 ±1.5 °C ±2 1 mA 1.25 400 1 MΩ 1.5 2.4 µA µA V DS1626/DS1726 TCOM, DQ Output Logic Voltages (Note 1) Thermal Drift VOL 4mA sink current (Note 4) 0.4 ±0.2 4 of 14 °C DS1626/DS1726 EEPROM AC ELECTRICAL CHARACTERISTICS (VDD = 2.7V to 5.5V; TA = -55°C to +125°C.) PARAMETER EEPROM Write Cycle Time EEPROM Writes EEPROM Data Retention SYMBOL CONDITIONS twr NEEWR -55°C to +55°C tEEDR -55°C to +55°C MIN TYP 4 MAX 10 50k 10 UNITS ms Writes Years AC ELECTRICAL CHARACTERISTICS (VDD = 2.7V to 5.5V; TA = -55°C to +125°C.) PARAMETER Temperature Conversion Time Data In to Clock Setup Clock to Data In Hold Clock to Data Out Delay Clock Low/High Time Clock Frequency Clock Rise/Fall Time RST to Clock Setup Clock to RST Hold RST Inactive Time Clock High to I/O Hi-Z RST Low to I/O Hi-Z CNV Pulse Width I/O Capacitance Input Capacitance SYMBOL tTC tDC tCDH tCDD tCL, tCH fCLK tR, tF tRC tCRH tRI tCDZ tRDZ tCNV CI/O CI CONDITIONS 9-bit 10-bit 11-bit 12-bit (Note 5) (Note 5) (Notes 5, 6) (Note 5) (Note 5) (Note 5) (Note 5) (Note 5) (Note 7) (Note 5) (Note 5) (Note 8) MIN TYP MAX 93.75 187.5 375 750 35 40 150 285 0 1.75 500 100 40 125 50 50 500ms 250ns 10 5 UNITS ms ns ns ns ns MHz ns ns ns ns ns ns pF pF NOTES: 1) 2) 3) 4) 5) 6) 7) 8) All voltages are referenced to ground. See Figure 2 for TYPICAL OPERATING CURVES. ISTBY, IDD specified with DQ, CLK/CNV = VDD and RST = GND. Drift data is based on a 1000hr stress test at +125°C with VDD = 5.5V. See Timing Diagrams in Figure 3. All timing is referenced to 0.7 x VDD and 0.3 x VDD. Load capacitance = 50pF. tRI must be 10ms minimum following any write command that involves the E2 memory. 250ns is the guaranteed minimum pulse width for a conversion to start, however, a smaller pulse width may start a conversion. 5 of 14 DS1626/DS1726 Figure 2. TYPICAL OPERATING CURVES 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 DS1726 ERROR (°C) ERROR °C DS1626 +3σ MEAN -3σ 0 10 20 30 40 50 60 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 +3σ MEAN -3σ -10 70 0 10 20 30 40 50 60 70 80 REFERENCE TEMPERATURE (°C) REFERENCE TEMPERATURE (°C) Figure 3. TIMING DIAGRAMS a) Read Timing tCRH tRC b) Write Timing tRI tCRH tRC 6 of 14 DS1626/DS1726 OPERATION—MEASURING TEMPERATURE The DS1626/DS1726 measure temperature using a bandgap-based temperature sensor. A delta-sigma analog-to-digital converter (ADC) converts the measured temperature to a digital value that is calibrated in degrees centigrade; for Fahrenheit applications a lookup table or conversion routine must be used. Communication with the DS1626/DS1726 is achieved through a 3-wire serial interface, and all data is transmitted LSb first. The DS1626/DS1726 can be programmed to take continuous temperature measurements (continuous conversion mode) or to take single temperature measurements on command (one-shot mode). The measurement mode is programmed by the 1SHOT bit in the configuration register as explained in the CONFIGURATION REGISTER section of this data sheet. The 1SHOT bit is stored in EEPROM, so it can be programmed prior to installation if desired. In continuous conversion mode, when a Start Convert T command is issued the DS1626/DS1726 perform consecutive temperature measurements until a Stop Convert T command is issued. In one-shot mode, the Start Convert T command causes one temperature measurement to be taken and then the DS1626/DS1726 return to a low-power idle state. The resolution of the DS1626/DS1726 digital temperature data is user-configurable to 9, 10, 11, or 12 bits, corresponding to temperature increments of 0.5°C, 0.25°C, 0.125°C, and 0.0625°C, respectively. The resolution is set by the EEPROM R0 and R1 bits in the configuration register. Note that the conversion time doubles for each additional bit of resolution. After each temperature measurement and analog-to-digital conversion, the DS1626/DS1726 store the measured temperature as a two’s complement number in the 12-bit temperature register (see Figure 4). The sign bit (S) indicates if the temperature is positive or negative: for positive numbers S = 0 and for negative numbers S = 1. The Read Temperature command provides user access to the temperature register. When the DS1626/DS1726 are configured for 12-bit resolution, all 12 bits of the temperature register will contain temperature data. For 11-bit resolution, the 11 MSbs (bits 11 through 1) of the temperature register will contain data and bit 0 will read out as 0. Likewise, for 10-bit resolution, the 10 MSbs (bits 11 through 2) will contain data, and for 9-bit the 9 MSbs (bits 11 through 3) will contain data, and all unused LSbs will contain 0s. Since the DS1626/DS1726 transmit data LSb first, when reading data from the temperature register, all 12 bits must be read in order to receive all MSbs of the measured data, regardless of the conversion resolution. Table 4 gives examples of 12-bit resolution digital output data and the corresponding temperatures. Figure 4. TEMPERATURE, TH, and TL REGISTER FORMAT bit 11 S bit 10 2 6 bit 19 2 5 bit 8 2 4 bit 7 2 3 bit 6 2 2 bit 5 2 1 bit 4 2 7 of 14 0 bit 3 2 -1 bit 2 2 -2 bit 1 2 -3 bit 0 2-4 DS1626/DS1726 Table 4. 12-BIT RESOLUTION TEMPERATURE/DATA RELATIONSHIP TEMPERATURE (°C) +125 +25.0625 +10.125 +0.5 0 -0.5 -10.125 -25.0625 -55 DIGITAL OUTPUT (BINARY) DIGITAL OUTPUT (HEX) 0111 1101 0000 0001 1001 0001 0000 1010 0010 0000 0000 1000 0000 0000 0000 1111 1111 1000 1111 0101 1110 1110 0110 1111 1100 1001 0000 7D0h 191h 0A2h 008h 000h FF8h F5Eh E6Fh C90h OPERATION—THERMOSTAT FUNCTION The DS1626/DS1726 thermostat outputs (THIGH, TLOW, and TCOM) are updated after every temperature conversion and remain at the updated values until the next conversion completes. THIGH is asserted when the measured temperature is higher than or equal to the value stored in the TH register, and TLOW is asserted when the temperature is equal to or falls below the value in the TL register (see Figure 5). TCOM uses both TH and TL to provide programmable hysteresis: when the measured temperature equals or exceeds TH, TCOM is asserted and it remains asserted until the temperature falls to a value equal to or below TL. All three thermostat outputs are active-high outputs. The Write TH and Write TL commands are used to program the 12-bit TH and TL registers with userdefined two’s complement values. The MSb (bit 11) of each register contains the two’s complement sign bit (S). For the TCOM thermostat output to function correctly, the TL value must be less than the TH value. Any unused LSbs in the TH and TL registers are forced to 0 regardless of the data written to those bits. The unused LSbs are determined by the conversion resolution set by R1 and R0 in the configuration register. Therefore, for 9-bit conversions bits 2 through 0 will be 0, for 10-bit conversions bit 1 and bit 0 will be 0, and for 11-bit conversions bit 0 will be 0. All bits are used for 12bit conversions, so no bits are forced to 0. However, regardless of the conversion resolution, when writing to TH or TL at least 12 bits must be sent following the Write TH or Write TL commands. The reason is that data written to TH and TL is not saved to EEPROM until the DS1626/DS1726 have received 12 bits, so if the operation is terminated before 12 bits have been received, the data will be lost. Any additional bits sent after the first twelve are ignored (e.g., if two 8-bit words are written). Another DS1626/DS1726 thermostat feature is the temperature-high flag (THF) and temperature-low flag (TLF) in the configuration register. These bits provide a record of whether the temperature has been greater than or equal to TH or less than or equal to TL at any time since the DS1626/DS1726 were powered up. If the temperature is greater than or equal to the TH register value, the THF bit in the configuration register will be set to 1. If the temperature is less than or equal to the TL register value, the TLF bit in the configuration register will be set to 1. Once THF and/or TLF has been set, it will remain set until the user overwrites it with a 0 or until the power is cycled. 8 of 14 DS1626/DS1726 CPU BIT AND STAND-ALONE THERMOSTAT OPERATION In stand-alone thermostat mode, DS1626/DS1726 thermostat functionality can be used without requiring a microcontroller to start/stop temperature conversions. The CPU bit in the configuration register determines if stand-alone mode is enabled. When CPU = 1 stand-alone mode is disabled, and the only way to start/stop temperature conversions is by using a microcontroller to transmit Start Convert T and Stop Convert T commands, respectively. Stand-alone mode is enabled when CPU = 0. In this mode, when RST = 0 the CLK/CNV pin operates as a control signal to start and stop temperature measurements. Driving CLK/CNV low initiates continuous temperature conversions that will continue until CLK/CNV is brought high again. If the CLK/CNV pin is driven low and then returned to a high state in less than 10ms, only one temperature conversion will be performed after which the DS1626/DS1726 will return to a low-power idle state (i.e., one-shot operation). Note that when stand-alone mode is enabled, the 1SHOT bit in the configuration register is ignored, and only the CLK/CNV signal determines whether continuous or oneshot conversions take place. Since TH, TL, and the CPU bit are stored in EEPROM, the DS1626/DS1726 can be preprogrammed for stand-alone operation. If desired, the CLK/CNV and RST pin can be connected to GND so the DS1626/DS1726 will automatically begin taking temperature measurements at power-up Normal bus communication with the DS1626/DS1726 can still take place in stand-alone mode when RST = 1. When communication is initiated, stand-alone conversions are automatically halted. If during the bus communication continuous temperature conversions are started using the Start Convert T command, they can only be stopped by issuing a Stop Convert T command. 9 of 14 DS1626/DS1726 Figure 5. THERMOSTAT OUTPUT OPERATION TH TL LOGIC 1 TCOM LOGIC 0 TEMP LOGIC 1 THIGH LOGIC 0 TEMP LOGIC 1 TLOW LOGIC 0 TEMP CONFIGURATION REGISTER The configuration register allows the user to customize the DS1626/DS1726 conversion and thermostat options. It also provides information to the user about conversion status, EEPROM activity, and thermostat activity. The configuration register is arranged as shown in Figure 6 and detailed descriptions of each bit are provided in Table 5. This register can be accessed using the Read Config and Write Config commands. Note that the R1, R0, CPU, and 1SHOT bits are stored in EEPROM and all other configuration register bits are SRAM. Figure 6. CONFIGURATION REGISTER MSb bit 6 bit 5 bit 4 bit 3 bit 2 DONE THF TLF NVB R1* R0* *NV (EEPROM) 10 of 14 bit 1 LSb CPU* 1SHOT* DS1626/DS1726 Table 5. CONFIGURATION REGISTER BIT DESCRIPTIONS BIT NAME (USER ACCESS) DONE (Read Only) THF (Read/Write) TLF (Read/Write) NVB (Read Only) R1* (Read/Write) R0* (Read/Write) CPU* (Read/Write) 1SHOT* (Read/Write) FUNCTIONAL DESCRIPTION Power-up state = 1. DONE = 0. Temperature conversion is in progress. DONE = 1. Temperature conversion is complete. Power-up state = 0. THF = 1. The measured temperature has reached or exceeded the value stored in the TH register. THF will remain a 1 until it is overwritten with a 0 by the user, the power is cycled, or a Software POR command is issued. Power-up state = 0. TLF = 1. The measured temperature has equaled or dropped below the value stored in the TL register. TLF will remain a 1 until it is overwritten with a 0 by the user, the power is cycled, or a Software POR command is issued. Power-up state = 0. NVB = 1. Write to an E2 memory cell is in progress. NVB = 0. NV memory is not busy. Power-up state = last value written to this bit. Sets conversion resolution (see Table 6). Initial state from factory = 1. Power-up state = last value written to this bit. Sets conversion resolution (see Table 6). Initial state from factory = 1. Power-up state = last value written to this bit. CPU = 1. Stand-alone mode is disabled. CPU = 0. Stand-alone mode is enabled when RST = 0. See CPU BIT AND STAND-ALONE THERMOSTAT OPERATION section for more information. Initial state from factory = 0. Power-up state = last value written to this bit. 1SHOT = 1: One-Shot Mode. The Start Convert T command initiates a single temperature conversion and then the device goes into a low-power standby state. 1SHOT = 0: Continuous Conversion Mode. The Start Convert T command initiates continuous temperature conversions. Initial state from factory = 0. *NV (EEPROM) Table 6. RESOLUTION CONFIGURATION R1 R0 RESOLUTION 0 0 1 1 0 1 0 1 9-bit 10-bit 11-bit 12-bit 11 of 14 CONVERSION TIME (MAX) 93.75ms 187.5ms 375ms 750ms DS1626/DS1726 3-WIRE SERIAL DATA BUS The 3-wire bus consists of three signals: RST (reset—active low), CLK (clock), and DQ (data). 3-wire communication is controlled by the RST signal, which functions as “chip select” signal. All data is transferred LSb first over the 3-wire bus. All communication with the DS1626/DS1726 is initiated by driving RST high. Driving RST low terminates communications and causes DQ to go to a highimpedance state. Note that RST must be toggled low after every communication sequence to ensure that subsequent commands are recognized by the DS1626/DS1726. When writing to the DS1626/DS1726, data must be valid during the rising edge of CLK. During read operations the DS1626/DS1726 output data on DQ on the falling edge of CLK and the data remains valid through the following rising edge, at which time the DQ pin becomes high impedance until the next falling edge. To communicate with the DS1626/DS1726, the master must first drive RST high and then begin generating the CLK signal while transmitting the desired DS1626/DS1726 command byte. If the command is a Start Convert T, Stop Convert T, or Software POR command, the transaction is finished when the last bit of the command has been sent. Figure 7a illustrates a Start Convert T command sequence. When writing to the DS1626/DS1726, the master must begin transmitting data during the clock cycle immediately following the command byte. The DS1626/DS1726 will save only the number of data bits needed for the specific transaction. For example, for the Write TH or Write TL commands, after twelve bits of data have been transmitted by the master, the DS1626/DS1726 will ignore any subsequent data transmitted before RST goes low. Thus, if data is being transmitted in byte-length segments, the DS1626/DS1726 will load the first twelve bits into the TH/TL register, and the next four bits will be ignored. On the other hand, it is necessary to transmit at least the required number of bits for the requested transaction (i.e., 12-bits to TH/TL or 8-bits to the configuration register), because the DS1626/DS1726 will not save data until the expected number of bits have been received. Write TH and Write TL sequences are illustrated in Figure 7b and a Write Config sequence is shown in Figure 7c. Note that these figures assume byte-wide data transfers. When reading data from the DS1626/DS1726, the DS1626/DS1726 will begin sending data during the clock cycle immediately following the command byte. After the last data byte has been sent, the DS1626/DS1726 will transmit a 0 during each subsequent clock until RST goes low. Figure 7d illustrates a Read Temperature sequence and a Read Config transaction is shown in Figure 7e. The sequence for reading the TH or TL registers is the same as the Read Temp transaction in Figure 7d except that the Read TH or Read TL command is used. 12 of 14 DS1626/DS1726 Figure 7. 3-WIRE COMMUNICATION a) Start Temperature Conversion RST CLK DQ 1 0 0 0 1 0 1 0 Start Convert T [51h] Command b) Write to the TH/TL Registers ⋅⋅⋅ RST CLK DQ ⋅⋅⋅ C0 0 C1 0 0 0 0 0 D0 D1 D2 Write TH [01h] or TL [02h] Command D3 D4 D5 D7 D6 D8 D9 D10 D11 TH or TL Data from Master c) Write to the Configuration Register RST CLK DQ 0 0 1 1 0 0 0 D0 0 Write Config [0Ch] Command D1 D2 D3 D4 D5 D6 D7 Configuration Reg. Data from Master d) Read from the Temperature Register ⋅⋅⋅ RST CLK 1 DQ 0 1 0 1 0 1 0 D0 1 D1 Read Temperature [AAh] Command D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 Temperature Data from DS1626/DS1726 e) Read from the Configuration Register RST CLK DQ 0 0 1 1 0 1 0 Read Config [ACh] Command 1 D0 D1 D2 D3 D4 D5 D6 D7 Configuration Reg. Data from DS1626/DS1726 13 of 14 0 0 0 ⋅⋅⋅ ⋅⋅⋅ DS1626/DS1726 DS1626/DS1726 COMMAND SET The DS1626/DS1726 command set is detailed below: Start Convert T 51h 0101 0001 Initiates temperature conversions. If the DS1626/DS1726 are in one-shot mode (1SHOT = 1), only one conversion will be performed. If the devices are in continuous mode (1SHOT = 0), continuous conversions will be performed until a Stop Convert T command is issued. Stop Convert T 22h 0010 0010 Stops temperature conversions when the devices are in continuous conversion mode (1SHOT = 0). Read Temperature AAh 1010 1010 Reads the last converted temperature value from the temperature register. Read TH A1h 1010 0001 Reads the 12-bit TH register. Read TL A2h 1010 0010 Reads the 12-bit TL register. Write TH* 01h 0000 0001 Writes the 12-bit TH register. Write TL* 02h 0000 0010 Writes the 12-bit TL register. Read Config ACh 1010 1100 Reads the 1-byte configuration register. Write Config* 0Ch 0000 1100 Writes the 1-byte configuration register. Software POR 54h 0101 0100 Initiates a software power-on reset (POR), which stops temperature conversions and resets all registers and logic to their power-up states. The software POR allows the user to simulate cycling the power without actually powering down the device. *After issuing a write command, no further writes should be requested for at least 10ms due to the EEPROM write cycle time. 14 of 14