KHP RHP KILOVOLT HIGH CURRENT RECTIFIER ASSEMBLIES MATCHED SILICON RECTIFIER ELEMENTS RATED CURRENT TO 3.0 AMPERES PRV 5,000 TO 50,000 VOLTS FAST RECOVERY (RHP SERIES) ALL APPLICABLE MIL-STD-750 TESTS HIGH THERMAL CONDUCTIVITY ENCAPSULATION EDI Type No. Peak ReverseVoltage PRV (Volts) Avg. Fwd.Current IO at 25 oC (Am ps) Max. Fwd Voltage Drop at 25 o C and 3 Amps V F (Volts) Dim ens ion L Inches Fig .3 Dim ens ion W Inches Fig .3 Case Sty le Fig .3 STANDARD RECOVERY KHP5 KHP6 KHP7 KHP8 KHP9 KHP10 KHP15 KHP20 KHP25 KHP30 KHP35 KHP40 KHP50 5,000 6,000 7,000 8,000 9,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 50,000 RHP5 RHP6 RHP7 RHP8 RHP9 RHP10 RHP15 RHP20 RHP25 RHP30 RHP35 RHP40 RHP50 5,000 6,000 7,000 8,000 9,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 50,000 3.00 2.75 2.75 2.75 2.50 2.50 2.50 2.25 2.25 2.25 2.25 2.25 2.25 8 9 10 11 14 15 21 28 36 42 49 63 70 4.00 4.75 5.50 6.00 6.50 7.00 4.00 6.00 8.00 4.00 6.00 8.00 6.00 1.0 1.0 1.0 1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 3.0 4.0 A A A A A A B B B B B B B 1.0 1.0 1.0 1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 3.0 4.0 A A A A A A B B B B B B B 200 NANOSECOND RECOVERY (FIG.4) 2.50 2.50 2.50 2.50 2.50 2.50 2.25 2.25 2.25 2.25 2.25 2.25 2.25 ELECTRICAL CHARACTERISTICS (at TA =25 C Unless Otherwise Specified) KHP SERIES STANDARD RECOVERY o Max. DC Reverse Current @ PRV and 25 C, IR 5 o Max. DC Reverse Current @ PRV and 100 C, IR Ambient Operating Temperature Range,TA Storage Temperature Range, TSTG 10 11 12 13 16 17 25 33 42 50 58 65 82 100 4.00 4.75 5.50 6.00 6.50 7.00 4.00 6.00 8.00 4.00 6.00 8.00 6.00 ELECTRICAL CHARACTERISTICS (at TA =25 C Unless Otherwise Specified) RHP SERIES FAST RECOVERY o Max. DC Reverse Current @ PRV and 25 C, IR A 5 o Max. DC Reverse Current @ PRV and 100 C, IR A A 250 A o o Max. Reverse Recovery Time , Trr (Fig.4) o o Ambient Operating Temperature Range,TA -55 oC to +150 oC -55 oC to +150 oC -55 C to +150 C -55 C to +150 C Max.One-Half Cycle Surge Current, I FM (Surge )@ 60Hz 400 Amps Storage Temperature Range, TSTG Forward Current Repetitive Peak,I FRM 40 Amps Max.One-Half Cycle Surge Current, I FM (Surge )@ 60Hz 200 nanosec Forward Current Repetitive Peak,I FRM EDI reserves the right to change these specifications at any time without notice. 240 Amps 25 Amps KHP FIG.1 FIG.2 OUTPUT CURRENT vs AMBIENT TEMPERATURE NON-REPETITIVE SURGE CURRENT 400 75 50 25 0 0 25 50 75 100 AMBIENT TEMPERATURE 125 150 (O C) IFSM. PEAK SURGE CURRENT (AMP) 100 % RATED FWD CURRENT RHP 300 240 200 KHP 150 100 RHP 70 50 30 20 1 3 2 FIG.3 PACKAGE STYLE CASE STYLE A 4 6 8 10 20 60 80 100 CASE STYLE B OUTLINE 8-32 THREAD X 1/4 DEEP (2) MTG. INSERTS OUTLINE 3 8 L L MAX. W 1 1 4 30 40 NUMBER OF CYCLES(60 Hz) 1 1 4 W 6-32 THREAD X 1/4 DEEP (2) MTG. INSERTS 1 4 1 4 1 4 8-32 THREAD X 1/4 DEEP (4) MTG. INSERTS It is recommended that a proper heat sink be used on the terminals of this device between the body and the soldering point to prevent damage form excess heat. TEST CIRCUIT FIG.4 TYPICAL REVERSE RECOVERY WAVEFORM ZERO REFERENCE 0.5A D.U.T. + T RR R1 50 OHM 1.0A 0.25A PULSE GENERATOR R2 1 OHM SCOPE R1, R2 NON-INDUCTIVE RESISTORS PULSE GENERATOR - HEWLETT PACKARD 214A OR EQUIV. IKC REP.RATE, 10 SEC. PULSE WIDTH ADJUST PULSE AMPLITUDE FOR PEAK IR Prior to the manufacture of these assemblies, the individual silicon junction is measured for maximum recovery time in the test circuit shown. ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951. 21 GRAY OAKS AVENUE * YONKERS. NEW YORK 10710 914-965-4400 Ee-mail:[email protected]:http:// * www.edidiodes.com * FAX 914-965-5531 * 1-800-678-0828