KVP RVP KILOVOLT RECTIFIER ASSEMBLIES MATCHED SILICON RECTIFIER ELEMENTS RATED CURRENT TO 1.0 AMPERES PRV 5,000 TO 50,000 VOLTS FAST RECOVERY (RVP SERIES) ALL APPLICABLE MIL-STD-750 TESTS HIGH THERMAL CONDUCTIVITY ENCAPSULATION EDI Type No. Peak Reverse Voltage PRV ( Volt s) KVP5 KVP6 KVP7 KVP8 KVP9 KV P10 KV P15 KV P20 KV P25 KVP30 KV P35 KV P40 KV P50 5,000 6,000 7,000 8,00 0 9,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 50,000 RVP5 RVP6 RV P7 RV P8 RV P9 RV P10 RV P15 RV P20 RV P25 RVP30 RVP35 RVP40 RVP50 5,000 6,000 7,000 8,000 9,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 50,000 Avg . Fwd .Cu rre nt o IO at 25 C (Am ps) Max. Fwd Voltage Drop at 25oC and 1A. VF (Volts) Dim ensi on L Inches Fig .3 STANDARD RECOVERY 1.00 8 1.00 9 1.00 10 1.00 11 1.00 14 1.00 15 1.00 21 .75 26 .75 32 .75 39 .75 46 .75 53 .75 65 200 NANOSECOND RECOVERY (FIG.4) .90 10 .90 11 .90 12 .90 13 .90 16 .90 17 .90 25 .70 30 .70 36 .70 43 .70 50 .70 58 .70 72 ELECTRICAL CHARACTERISTICS (at TA =25 C Unless Otherwise Specified) o Max. DC Reverse Current @ PRV and 25 C, IR o Max. DC Reverse Current @ PRV and 100 C, IR KVP SERIES STANDARD RECOVERY 5 100 Dim ensi on C Inch es Fig .3 2.5 2.5 3.0 3.0 3.0 3.5 5.0 5.5 6.0 6.0 6.5 6.5 7.0 1 /4 3 /8 1/ 1 /2 2.5 2.5 3.0 3.0 3.0 3.5 5.0 5.5 6.0 6.0 6.5 6.5 7.0 1 /4 3 /8 1 /4 1 /2 ELECTRICAL CHARACTERISTICS (at TA =25 C Unless Otherwise Specified) o Max. DC Reverse Current @ PRV and 25 C, IR A A 4 o Max. DC Reverse Current @ PRV and 100 C, IR RVP SERIES FAST RECOVERY 5 A 250 A Ambient Operating Temperature Range,TA -55 oC to +150 oC Max. Reverse Recovery Time , Trr (Fig.4) Storage Temperature Range, TSTG -55 oC to +150 oC Ambient Operating Temperature Range,TA -55 oC to +150 oC -55 oC to +150 oC Max.One-Half Cycle Surge Current, I FM (Surge )@ 60Hz 50 Amps Storage Temperature Range, TSTG Forward Current Repetitive Peak,I FRM 10 Amps Max.One-Half Cycle Surge Current, I FM (Surge )@ 60Hz Forward Current Repetitive Peak,I FRM 300 nanosec 30 Amps 8 Amps EDI reserves the right to change these specifications at any time without notice. KVP FIG.1 FIG.2 NON-REPETITIVE SURGE CURRENT RATINGS OUTPUT CURRENT vs AMBIENT TEMPERATURE 0.1SEC 100 1.0SEC 100 75 % MAXIMUM SURGE % RATED FWD CURRENT RVP 50 25 0 75 50 25 0 0 25 50 75 100 AMBIENT TEMPERATURE 125 1 150 2 3 4 (O C) 5 6 7 8 9 10 20 30 40 50 60 CYCLES(60 Hz) FIG.3 CASE STYLE A C 3 8 MAX. L 3 4 1 4 1 4 6-32 THREAD X 1/4 DEEP 3 4 (2) MTG. INSERTS (ALL DIMENSIONS IN INCHES) It is recommended that a proper heat sink be used on the terminals of this device between the body and the soldering point to prevent damage form excess heat. TEST CIRCUIT FIG.4 TYPICAL REVERSE RECOVERY WAVEFORM 0.5A D.U.T. + T RR R1 50 OHM PULSE GENERATOR ZERO R2 REFERENCE 1 OHM 1.0A 0.25A SCOPE R1, R2 NON-INDUCTIVE RESISTORS PULSE GENERATOR - HEWLETT PACKARD 214A OR EQUIV. IKC REP.RATE, 10 SEC. PULSE WIDTH ADJUST PULSE AMPLITUDE FOR PEAK IR ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951. 21 GRAY OAKS AVENUE * YONKERS. NEW YORK 10710 914-965-4400 Ee-mail:[email protected] * Wwebsite: http://www.edidiodes.com * FAX 914-965-5531 * 1-800-678-0828