EM78P311N 8-BIT Microcontroller Green Product Specification DOC. VERSION 1.0 ELAN MICROELECTRONICS CORP. October 2006 Trademark Acknowledgments: IBM is a registered trademark and PS/2 is a trademark of IBM. Windows is a trademark of Microsoft Corporation. ELAN and ELAN logo are trademarks of ELAN Microelectronics Corporation. Copyright © 2006 by ELAN Microelectronics Corporation All Rights Reserved Printed in Taiwan The contents of this specification are subject to change without further notice. ELAN Microelectronics assumes no responsibility concerning the accuracy, adequacy, or completeness of this specification. ELAN Microelectronics makes no commitment to update, or to keep current the information and material contained in this specification. Such information and material may change to conform to each confirmed order. In no event shall ELAN Microelectronics be made responsible for any claims attributed to errors, omissions, or other inaccuracies in the information or material contained in this specification. ELAN Microelectronics shall not be liable for direct, indirect, special incidental, or consequential damages arising from the use of such information or material. The software (if any) described in this specification is furnished under a license or nondisclosure agreement, and may be used or copied only in accordance with the terms of such agreement. ELAN Microelectronics products are not intended for use in life support appliances, devices, or systems. Use of ELAN Microelectronics product in such applications is not supported and is prohibited. NO PART OF THIS SPECIFICATION MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS WITHOUT THE EXPRESSED WRITTEN PERMISSION OF ELAN MICROELECTRONICS. ELAN MICROELECTRONICS CORPORATION Headquarters: Hong Kong: USA: No. 12, Innovation Road 1 Hsinchu Science Park Hsinchu, Taiwan 30077 Tel: +886 3 563-9977 Fax: +886 3 563-9966 http://www.emc.com.tw Elan (HK) Microelectronics Corporation, Ltd. Flat A, 19F., World Tech Centre 95 How Ming Street, Kwun Tong Kowloon , HONG KONG Tel: +852 2723-3376 Fax: +852 2723-7780 [email protected] Elan Information Technology Group (U.S.A.) Europe: Shenzhen: Shanghai: Elan Microelectronics Corp. (Europe) Elan Microelectronics Shenzhen, Ltd. Elan Microelectronics Shanghai, Ltd. Siewerdtstrasse 105 8050 Zurich, SWITZERLAND Tel: +41 43 299-4060 Fax: +41 43 299-4079 http://www.elan-europe.com SSMEC Bldg., 3F, Gaoxin S. Ave. Shenzhen Hi-Tech Industrial Park Shenzhen, Guandong, CHINA Tel: +86 755 2601-0565 Fax: +86 755 2601-0500 23/Bldg. #115 Lane 572, Bibo Road Zhangjiang Hi-Tech Park Shanghai, CHINA Tel: +86 21 5080-3866 Fax: +86 21 5080-4600 1821 Saratoga Ave., Suite 250 Saratoga, CA 95070 U.S.A. Tel: +1 408 366-8225 Fax: +1 408 366-8220 Contents Contents 1 2 3 4 5 General Description.....................................................................................................1 Features ........................................................................................................................1 Pin Assignment ............................................................................................................1 Pin Description.............................................................................................................2 Function Description...................................................................................................3 5.1 Functional Block Diagram .................................................................................... 3 5.2 Operating Registers ............................................................................................. 4 5.3 Special Purpose Registers ................................................................................. 19 5.4 CPU Operation Mode ......................................................................................... 23 5.5 AD Converter...................................................................................................... 24 5.6 Time Base Timer and Keytone Generator ......................................................... 26 5.7 UART (Universal Asynchronous Receiver/Transmitter)..................................... 28 5.7.1 5.7.2 5.7.3 5.7.4 5.8 SPI (Serial Peripheral Interface) ........................................................................ 31 5.8.1 5.8.2 5.8.3 5.9 UART Mode ...................................................................................................... 29 Transmitting ...................................................................................................... 29 Receiving .......................................................................................................... 30 Baud Rate Generator ....................................................................................... 30 Serial Clock....................................................................................................... 32 Shift Direction and Sample Phase.................................................................... 32 Transfer Mode .................................................................................................. 32 Timer/Counter 2.................................................................................................. 35 5.9.1 5.9.2 5.9.3 Timer Mode....................................................................................................... 36 Counter Mode ................................................................................................... 36 Window Mode ................................................................................................... 36 5.10 Timer/Counter 3.................................................................................................. 37 5.10.1 Timer Mode....................................................................................................... 38 5.10.2 Counter Mode ................................................................................................... 38 5.10.3 Capture Mode ................................................................................................... 38 5.11 Timer/Counter 4.................................................................................................. 39 5.11.1 5.11.2 5.11.3 5.11.4 Timer Mode....................................................................................................... 40 Counter Mode ................................................................................................... 40 PDO Mode ........................................................................................................ 40 PWM Mode ....................................................................................................... 41 5.12 TCC/WDT & Prescaler ....................................................................................... 41 5.13 I/O Ports.............................................................................................................. 42 Product Specification (V1.0) 10.02.2006 • iii Contents 5.14 Reset and Wake-up............................................................................................ 42 5.14.1 5.14.2 5.14.3 5.14.4 Reset ................................................................................................................ 42 Wake-up from Sleep Mode ............................................................................... 43 Wake-up from Idle Mode .................................................................................. 43 The Status of RST, T, and P of the Status Register .......................................... 48 5.15 Interrupt .............................................................................................................. 49 5.16 Oscillator............................................................................................................. 50 5.16.1 Oscillator Modes ............................................................................................... 50 5.16.2 Crystal Oscillator/Ceramic Resonators (Crystal) .............................................. 50 5.16.3 External RC Oscillator Mode ............................................................................ 52 5.17 Code Option Register......................................................................................... 53 5.17.1 Code Option Register (Word 0) ........................................................................ 53 5.17.2 Customer ID Register ....................................................................................... 54 5.18 Power-on Considerations ................................................................................... 54 5.18.1 External Power-on Reset Circuit ...................................................................... 54 5.18.2 Residue-Voltage Protection .............................................................................. 55 6 5.19 Instruction Set..................................................................................................... 56 Absolute Maximum Ratings .....................................................................................58 6.1 7 Absolute Maximum Ratings ............................................................................... 58 6.2 Recommended Operating Conditions................................................................ 58 Electrical Characteristics..........................................................................................59 7.1 DC Electrical Characteristics.............................................................................. 59 7.2 AC Electrical Characteristic................................................................................ 62 7.3 Timing Diagram .................................................................................................. 63 APPENDIX A Package Type: ............................................................................................................64 Specification Revision History Doc. Version 1.0 iv • Revision Description Initial Version Date 2006/10/02 Product Specification (V1.0) 10.02.2006 EM78P311N 8-Bit Microcontroller 1 General Description The EM78P311N is an 8-bit microprocessor with low-power, high-speed CMOS technology and high noise immunity. It has an on-chip 2K×13-bits Electrical One Time Programmable Read Only Memory (OTP-ROM). It provides multi-protection bits to prevent intrusion of user’s OTP memory codes. Seven Option bits are also available to meet user’s requirements. With its OTP-ROM feature, the EM78P311N provides a convenient way of developing and verifying user’s programs. Moreover, this OTP device offers the advantages of easy and effective program updates, using development and programming tools. User can avail of the ELAN Writer to easily program his development code. 2 Features CPU configuration z 2K×13 bits on-chip ROM z 80×8 bits on-chip registers (SRAM) z 8-level stacks for subroutine nesting z Less than 3.5mA at 5V/8MHz z Typically 0.8 μA, during sleep mode z Typically 1.1 μA, during idle mode I/O port configuration z 4 bidirectional I/O ports : P6, P7, P8, P9 z 22 I/O pins z 10 Programmable pull-down I/O pins z 10 programmable pull-high I/O pins z External interrupt : P60, P61, P73, P80 Operating voltage range: z OTP version Operating voltage range:2.5v~5.5v Operating temperature range: z -40~85°C Operating frequency range: Main clock z 8 bits Timer/Counter TCC: 8-bit real time clock/counter with overflow interrupt TC3: Timer/Counter/Capture TC4: Timer/Counter/ PWM (pulse width modulation)/PDO (Programmable divider output) z 8-bit channels Analog-to-Digital Converter with 10-bit resolution z Time Base Timer:(1Hz~16kHz at 8MHz) z Key tone output:(1kHz~8kHz at 8MHz) z 8-bit channels Analog-to-Digital Converter with 10-bit resolution Fifteen available interruptions: z WDT time-out interrupt z TCC overflow interrupt z Time base timer interrupt(the first falling edge of the source clock) z Serial UART transmit interrupt z Serial UART receive interrupt z Serial UART receive error interrupt z Four External interrupt z ADC completion interrupt z TC2 overflow interrupt z TC3 overflow interrupt z TC4 overflow interrupt z Serial SPI interrupt Special features z Programmable free running watchdog timer z Two clocks per instruction cycle z Power on Reset z High noise immunity z Power saving Sleep mode z Selectable Oscillation mode Package type: z 28-pin DIP 600 mil: EM78P311NP z 28-pin Skinny DIP 300 mil: EM78P311NAK z 28-pin Skinny DIP 400 mil: EM78P311N z 28-pin SOP 300 mil: EM78P311NM z 28-pin SSOP 209 mil: EM78P311NS • Crystal mode: DC ~ 20MHz/2clks @ 5V; DC ~100ns inst. cycle @ 5V DC ~ 8MHz/2clks @ 3V;DC ~ 250ns inst. cycle @ 3V • ERC mode: DC ~ 16MHz/2clks @ 5V;DC ~ 125ns inst. cycle @ 5V DC ~ 8MHz/2clks @ 3V;DC ~ 250ns inst. cycle @ 3V 3 Peripheral configuration z Serial peripheral interface (SPI) available z Universal asynchronous receiver transmitter interface (UART)available z 16 bits Counter/Timer TC2: Timer/Counter/Window Pin Assignment (ACLK) OSCO OSCI TEST (AD0) P90 (AD1) P91 (AD2) P92 (AD3) P93 (AD4) P94 (AD5) P95 (AD6) P96 (AD7/VREF) P97 (TC3, INT3) P80 (TC4, /PWM, /PDO) P81 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VDD /RESET (VPP) P67 (DINCK) P66 (DATAIN) P65 (PGMB) P64 (/SS)(OEB) P63 (/TONE) P62 (TC2) P61 (INT1) P60 (/INT0) P73 (/SLEEP, /INT5) P72 (TX,SO) P71(RX,SI) P70 (/SCK) EM78P311N Fig. 3- Pin Assignment Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) •1 EM78P311N 8-Bit Microcontroller 4 Pin Description Table 1 Symbol VDD Pin No. Type 28 − Power supply Crystal type: Crystal input terminal RC type: RC oscillator input pin OSCI 2 I OSCO 1 I/O /RESET 27 I P60~P67 P70~P73 19~26 15~18 Function Crystal type: Output terminal for crystal oscillator RC type: Instruction clock output External clock signal input Input pin with Schmitt Trigger. If this pin remains at logic low, the controller will also remain in reset condition. I/O 8-bit bidiectional input/output pins. P60 can be used as external Interrupt 0 (/INT0). P61 can be used as external Interrupt 1 (INT1). P62 can be used as 16-bit Timer/Counter 2 (TC2). P63 can be used as divider output (/TONE). P64 slave mode enable (/SS). P60 ~ P63 can be used as pull-high or pull-low pins. I/O 8-bit bidiectional input/output pins. P70 can be used as SPI serial clock input/output (/SCK) P71 can be used as SPI serial data input (SI) or UART data receive input (RX) P72 can be used as SPI serial data output (SO) or UART data transmit output (TX) P73 can be used as Sleep mode release input (/SLEEP) or external interrupt input 5 (/INT5) P70 ~ P73 can be used as pull-high or pull-low pins P80~P81 12~13 I/O 2-bit bidiectional input/output pins. P80 can be used as 8-bit Timer/Counter 3 (TC3) or external Interrupt Input 3 (INT3). P81 can be used as 8-bit Timer/Counter 4 (TC4) or programmable divider output (PDO). P80 ~ P81 can be used as pull-high or pull-low pins. P90~P97 4~11 I/O 8-bit bidiectional input/output pins. P90~P97 can be used as 8 channel 10-bit resolution A/D converter. P97 can be used as AD reference power supply input (VREF). VSS 14 − Ground NC 3 − No connection OTP Programming Pins 2• VPP 27 I Programming voltage input ACLK 1 I CLK for OTP memory address increment DATAIN 25 I/O DINCK 26 I ROM code input clock PGMB 24 I Program write enable pin. Active low. OEB 23 I Output enable pin. Active low. ROM code series input and series output pin Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 5 Function Description 5.1 Functional Block Diagram P9 P90 P91 P92 P93 P94 P95 P96 P97 Ext. OSC. PC ROM Ext. RC Start-up Timer WDT TC2 Instruction Register Oscillation Generation 8-level stack (13 bit) TC2 TC3 TC3 TC4 Reset Instruction Decoder P8 TC4 TX RX UART SPI P80 P81 Mux . ALU TCC Sin Sout SCK TCC Keytone TBKTC P7 P70 P71 P72 P73 P74 P75 P76 P77 R4 RAM ACC R3 Status Reg. Interrupt Control Register P6 P60 P61 P62 P63 P64 P65 P66 P67 Interrupt Circuit Ext INT0 Ext INT1 Ext INT3 ADC Ext INT5 Ain 0~7 Fig. 5-1 Functional Block Diagram Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) •3 EM78P311N 8-Bit Microcontroller 5.2 Operating Registers Register Bank 0 Register Bank 1 Register Bank 2 Register Bank 3 Control Register Address 00 R0/ IAR 01 R1/ TCC 02 R2/ PC 03 R3/ SR 04 R4/ RSR 05 SCR TC3CR URC1 SPIC1 Reserved 06 Port 6 TC3DA URC2 SPIC2 IOC6 07 Port 7 TC3DB URS SPID IOC7 08 Port 8 TC2CR/ ADDL URRD Reserved IOC8 09 Port 9 TC2DH URTD Reserved IOC9 0A Reserved TC2DL Reserved PHC1 Reserved 0B TC4CR ADCR Reserved PLC1 INTCR 0C TC4D ADIC Reserved PHC2 ADOSCR 0D ISFR0 ADDH Reserved PLC2 Reserved 0E ISFR1 TBKTC Reserved Reserved IMR1 0F ISFR2 Reserved Reserved Reserved IMR2 10 : 1F 16 Byte Common Register 20 : 3F R3 (7, 6) = (0, 1) Bank 0 R4 (7, 6) = (0, 0) Bank 1 R4 (7, 6) = (0, 1) 32 Byte Common Register 32 Byte Common Register R3 (7, 6) = (1, 0) R3 (7, ) = (1, 1) Fig. 5-2 Operating Registers 4• Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller R0 (Indirect Addressing Register) R0 is not a physically implemented register. Its major function is to act as an indirect addressing pointer. Any instruction using R0 as a pointer actually accesses data pointed by the RAM Select Register (R4). R1 (Time Clock /Counter) This register is writable and readable just like the other registers. The contents of the prescaler counter are cleared only when a value is written into the TCC register. R2 (Program Counter) & Stack z Depending on the device type, R2 and hardware stack are 10-bit wide. The structure is depicted in Fig.5-3. z Generates 8192 ×13 bits on-chip OTP ROM addresses to the relative programming instruction codes. One program page is 1024 words long. z R2 is set as all "0"s when under RESET condition z "JMP" instruction allows direct loading of the lower 10 program counter bits. Thus, "JMP" allows the PC to go to any location within a page. z "CALL" instruction loads the lower 10 bits of the PC, and then PC+1 is pushed onto the stack. Thus, the subroutine entry address can be located anywhere within a page. z "RET" ("RETL k", "RETI") instruction loads the program counter with the contents of the top-level stack. z All instructions are single instruction cycle (fclk/2 or fclk/4) except for the instruction that would change the contents of R2. Such instruction will need one more instruction cycle. z For an interrupt trigger, the program ROM will jump to individual interrupt vector at Page 0. The CPU will store ACC, R3 status and R5 PAGE automatically, it will restore after instruction RETI. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) •5 EM78P311N 8-Bit Microcontroller R5 PC A12 A11 A10 A9 A8 CALL RET RETL RETI 000 : PAGE0 0000~03FF 001 : PAGE1 0400~07FF 010 : PAGE2 0800~0BFF A7 ~ A0 Store ACC, R3, R5 Reset Vector 0000h WDT Timer Overflow 0003h External INT0 Pin Interrupt Occurs 0006h TCC Overflow 0009h External INT1 pin Interrupt Occurs 000Fh Time Base Timer Interrupt 0012h UART Transmit Data Buffer Empty 0015h UART Receive Data Buffer Full 0018h UART Receive Error 001Bh TC3 Interrupt 0021h SPI Interrupt 0024h TC4 Interrupt 0027h External INT3 Pin Interrupt Occurs 002Ah AD Conversion Complete 0030h TC2 Interrupt 0033h External INT5 Pin Interrupt Occurs 0036h Stack Level 1 Stack Level 2 011 : PAGE3 0C00~0FFF Stack Level 3 100 : PAGE4 1000~13FF Stack Level 4 Stack Level 5 101 : PAGE5 1400~17FF 110 : PAGE6 1800~1BFF Stack Level 7 Stack Level 8 111 : PAGE7 1C00~1FFF User Memory Space Stack Level 6 On-chip Program Memory 1FFFh Fig. 5-3 Program Counter Organization R3 (Status Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RBS1 RBS0 0 T P Z DC C Bit 7 ~ Bit 6 (RBS1 ~ RBS0): R-Register page select RBS1 RBS0 Register Bank (Address 05H ~ 0FH) 0 0 Bank 0 0 1 Bank 1 1 0 Bank 2 1 1 Bank 3 Bit 5: Not used Bit 4 (T): Time-out bit. Set to “1” with the "SLEP" and "WDTC" commands, or during power up, and reset to “0” with the WDT time-out. 6• Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Bit 3 (P): Power down bit. Set to “1” during power on or by a "WDTC" command and reset to “0” by a "SLEP" command. Bit 2 (Z): Zero flag. Set to "1" if the result of an arithmetic or logic operation is zero. Bit 1 (DC) : Auxiliary carry flag Bit 0 (C) : Carry flag R4 (RAM Select Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 GRBS1 RBS0 RSR5 RSR4 RSR3 RSR2 RSR1 RSR0 Bit 7: 6 ( GRBS1: GRBS0 ): determine which general purpose banks are activated among the two banks. Use BANK instruction (e.g. BABK 1) to change bank. GRBS1 GRBS0 General Purpose Register Bank (Address 20H ~ 3FH) 0 0 0 1 Bank 0 Bank 1 Bit 5: 0 ( RSR5 : RSR0 ): used to select the registers (Address: 00h~3Fh) in indirect addressing mode. If no indirect addressing is used, the RSR can be used as an 8-bit general-purpose read/write register. See the data memory configuration in Fig. 5-2. R5 (System Control Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 PS0 0 1 SIS REM Bit 4 (PS0): ROM Page select bits. User can use PAGE instruction (e.g. PAGE 1) or set PS0 bits to change the ROM page. When executing a "JMP", "CALL", or other instructions which cause the program counter to change (e.g. MOV R2, A), PS0 are loaded into the 11th bit of the program counter and select one of the available program memory pages. Note that RET (RETL, RETI) instruction does not change the PS0 bits. That is, return will always be to the page from where the subroutine was called, regardless of the PS0 bits current setting. PS0 Program Memory Page [Address] 0 Page 0 [0000~03FF] 1 Page 1 [0400~07FF] Bit 1 ( SIS ) : Sleep and Idle mode select SIS = “0” : Idle mode SIS = “1” : Sleep mode Bit 0 ( REM ) : Release method for sleep mode REM = “0” : /SLEEP pin input rising edge released REM = “1” : /SLEEP pin input “H” level released Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) •7 EM78P311N 8-Bit Microcontroller R6 (Port 6 I/O Data Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 P67 P66 P65 P64 P63 P62 P61 P60 Bit 7 ~ Bit 0 ( P67 ~ P60 ) : 8-bit Port 6 I/O data register User can use IOC6 register to define each bit whether input or output. R7 (Port 7 I/O Data Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 P73 P72 P71 P70 Bit 3 ~ Bit 0 ( P73 ~ P70 ) : Port 73 ~ Port 70 I/O data register User can use IOC7 register to define each bit whether input or output. R8 (Port8 I/O Data Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 P81 P80 Bit 1 ~ Bit 0 ( P81 ~ P80 ) : Port 81 ~ Port 80 I/O data register User can use IOC8 register to define each bit whether input or output. R9 (Port9 I/O Data Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 P97 P96 P95 P94 P93 P92 P91 P90 Bit 7 ~ Bit 0 ( P97 ~ P90 ) : 8-bit Port 97 ~ Port 90 I/O data register User can use IOC9 register to define each bit whether input or output. RB (Timer/Counter 4 Control Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC4FF1 TC4FF0 TC4S TC4CK2 TC4CK1 TC4CK0 TC4M1 TC4M0 Bit 7 ~ Bit 6 ( TC4FF1 ~ TC4FF0 ) : Timer/Counter 4 flip-flop control TC4FF1 TC4FF0 Operating Mode 0 0 Clear 0 1 Toggle 1 0 Set 1 1 Reserved Bit 5 ( TC4S ) : Timer/Counter 4 start control TC4S = “0” : Stop and clear counter TC4S = “1” : Start 8• Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Bit 4 ~ Bit 2 ( TC4CK2 ~ TC4CK 0 ) : Timer/Counter 4 Clock Source Select Clock Source Resolution Max. Time ( Normal, Idle ) ( Fosc=8M ) ( Fosc=8M ) 0 Fc/2^11 256uS 65mS 0 1 Fc/2^7 16uS 4mS 0 1 0 Fc/2^5 4uS 1mS 0 1 1 Fc/2^3 1uS 255uS 1 0 0 Fc/2^2 500nS 127.5uS 1 0 1 Fc/2^1 250nS 63.8uS 1 1 0 Fc 125nS 31.9uS 1 1 1 External clock (TC4 pin) -- -- TC4CK2 TC4CK1 TC4CK0 0 0 0 Bit 1 ~ Bit 0 ( TC4M1 ~ TC4M0 ) : Timer/Counter 4 Operating Mode Select TC4M1 TC4M0 Operating Mode 0 0 Timer/Counter 0 1 Reserved 1 0 Programmable Divider output 1 1 Pulse Width Modulation output RC (Timer 4 Data Buffer) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC4D7 TC4D6 TC4D5 TC4D4 TC4D3 TC4D2 TC4D1 TC4D0 Bit 7 ~ Bit 0 ( TC4D7 ~ TC4D0 ) : Data buffer of 8-bit Timer/Counter 4. RD (Interrupt Status Flag Register 0 and INT3 Edge Detect Flag) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 INT3F INT3R 0 0 WDTIF EXIF0 Bit 5 ( INT3F ) : External interrupt 3 falling edge detect flag. INT3F = “0” : Falling edge is not detected INT3F = “1” : Falling edge is detected Bit 4 ( INT3R ) : External interrupt 3 rising edge detect flag. INT3R = “0” : Rising edge is not detected INT3R = “1” : Rising edge is detected Bit 1 ( WDTIF ) : WDT time-out flag, flag cleared by software. Bit 0 ( EXIF0 ) : External interrupt flag (INT0). Flag cleared by software. If the INT0EN is reset to “0”, the flag is cleared. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) •9 EM78P311N 8-Bit Microcontroller RE (Interrupt Status Flag Register 1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 EXIF5 TCIF2 ADIF 0 EXIF3 TCIF4 SPIF TCIF3 Bit 7 ( EXIF5 ) : External Interrupt Flag (/INT5), flag cleared by software. Bit 6 ( TCIF2 ) : 16-bit Timer/Counter 2 Interrupt Flag, flag cleared by software. Bit 5 ( ADIF ) : AD conversion complete flag, flag cleared by software. Bit 3 ( EXIF3 ) : External Interrupt Flag (/INT3), flag cleared by software. Bit 2 ( TCIF4 ) : 8-bit Timer/Counter 4 Interrupt Flag, flag cleared by software. Bit 1 ( SPIF ) : SPI Mode Interrupt Flag, flag cleared by software. Bit 0 ( TCIF3 ) : 8-bit Timer/Counter 3 interrupt flag, flag cleared by software. 0 : means no interrupt request 1 : means with interrupt request z ISFR1 can be cleared by instruction, but cannot be set by instruction z IMR1 is the interrupt mask register z Note that reading ISFR1 will obtain the result of the ISFR1 "logic AND" and IMR1. RF(Interrupt Status Flag Register 2) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 UERRIF RBFF TBEF TBIF EXIF1 0 TCIF0 Bit 6 (UERRIF) : UART Receiving Error Interrupt, cleared by software or UART disabled. Bit 5 (RBFF) : UART Receive Mode Data Buffer Full Interrupt Flag. Flag cleared by software. Bit 4 (TBEF) : UART Transmit Mode Data Buffer Empty Interrupt Flag. Flag cleared by software. Bit 3 (TBIF) : Time Base Timer Interrupt Flag. Flag cleared by software. Bit 2 (EXIF1) : External Interrupt Flag (INT1). Flag cleared by software. Bit 0 (TCIF0) : TCC Overflow Interrupt Flag. Set as TCC overflows; flag cleared by software. 0 : means no interrupt request 1 : means with interrupt request 10 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller z ISFR2 can be cleared by instruction, but cannot be set by instruction z IMR2 is the interrupt mask register z Note that reading ISFR2 will obtain the result of the ISFR2 "logic AND" and IMR2 Bank 1 R5 TC3CR (Timer/Counter 3 Control Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC3CAP TC3S TC3CK1 TC3CK0 TC3M 0 0 0 Bit 7 ( TC3CAP ) : Software capture control TC3CAP = “0” : TC3CAP = “1” : Software capture Bit 6 ( TC3S ) : Timer/Counter 3 start control TC3S = “0” : Stop and counter clear TC3S = “1” : Start Bit 5 ~ Bit 4 ( TC3CK1 ~ TC3CK0 ) : Timer/Counter 3 Clock Source Select Clock source ( Normal, Idle ) Resolution ( Fc=8M ) Max. time ( Fc=8M ) 12 512μS 131.1mS 10 128μS 32.6mS 7 TC3CK1 TC3CK0 0 0 Fc/2 0 1 Fc/2 1 0 Fc/2 16μS 4.1mS 1 1 External clock (TC3 pin) - - Bit 3 ( TC3M ) : Timer/Counter 3 mode select TC3M = “0” : Timer/Counter3 mode TC3M = “1” : Capture mode Bank 1 R6 TC3DA (Timer 3 Data Buffer A) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC3DA7 TC3DA6 TC3DA5 TC3DA4 TC3DA3 TC3DA2 TC3DA1 TC3DA0 Bit 7 ~ Bit 0 ( TC3DA7 ~ TC3DA0 ) : Data buffer of 8-bit Timer/Counter 3. Reset does not affect this register. Bank 1 R7 TC3DB (Timer 3 Data Buffer B) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC3DB7 TC3DB6 TC3DB5 TC3DB4 TC3DB3 TC3DB2 TC3DB1 TC3DB0 Bit 7 ~ Bit 0 ( TC3DB7 ~ TC3DB0 ) : Data buffer of 8-bit Timer/Counter 3 Reset does not affect this register. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 11 EM78P311N 8-Bit Microcontroller Bank 1 R8 TC2CR/ ADDL (Timer/Counter 2 Control Register, AD Low 2 bits Data Buffer) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADD1 ADD0 0 TC2M TC2S TC2CK2 TC2CK1 TC2CK0 Bit 7 ~ Bit 6 ( ADD1 ~ ADD0 ) : AD low 2-bit data buffer Bit 4 ( TC2M ) : Timer/Counter 2 mode select TC2M = “0” : Timer/counter mode TC2M = “1” : Window mode Bit 3 ( TC2S ) : Timer/Counter 2 start control TC2S = “0” : Stop and counter clear TC2S = “1” : Start Bit 2 ~ Bit 0 ( TC2CK2 ~ TC2CK0 ) : Timer/Counter 2 Clock Source Select TC2CK2 TC2CK1 TC2CK0 0 0 0 Clock Source ( Normal, Idle ) Resolution ( Fc=8M ) Max. Time ( Fc=8M ) 23 1.05s 19.1h 13 1.02ms 1.1min 8 32μs 2.1s 3 Fc/2 0 0 1 Fc/2 0 1 0 Fc/2 0 1 1 Fc/2 1μs 65.5ms 1 0 0 Fc 125ns 7.9ms 1 0 1 - - - 1 1 0 - - - 1 1 1 External clock (TC2 pin) Bank 1 R9 TC2DH (Timer 2 Data Buffer High Byte) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC2D15 TC2D14 TC2D13 TC2D12 TC2D11 TC2D10 TC2D9 TC2D8 Bit 7 ~ Bit 0 ( TC2D15 ~ TC2D8 ) : 16-bit Timer/Counter 2 data buffer high byte. Bank 1 RA TC2DL (Timer 2 Data Buffer Low Byte) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC2D7 TC2D6 TC2D5 TC2D4 TC2D3 TC2D2 TC2D1 TC2D0 Bit 7 ~ Bit 0 ( TC2D7 ~ TC2D0 ) : 16-bit Timer/Counter 2 data buffer low byte. Bank 1 RB ADCR (AD Control Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADREF ADRUN ADCK1 ADCK0 ADP ADIS2 ADIS1 ADIS0 Bit 7 ( ADREF ) : AD reference voltage input select. ADREF = “0” : Internal VDD, P97 is used as IO. ADREF = “1” : External reference pin, P97 is used as reference input pin. 12 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Bit 6 ( ADRUN ) : AD Conversion start ADRUN = “0” : Reset on completion of the conversion by hardware, this bit cannot be reset by software. ADRUN = “1” : Conversion starts Bit 5~ Bit 4 ( ADCK1 ~ ADCK0 ) : AD Conversion Time Select Clock Source ( Normal, Idle ) Max. Operating Frequency (Fc) 0 Fc/4 1MHz 0 1 Fc/16 4MHz 1 0 Fc/32 8MHz 1 1 Reserved - ADCK1 ADCK0 0 Bit 3 ( ADP ) : AD power control ADP = “0” : Power on ADP = “1” : Power down Bit 2 ~ Bit 0 ( ADIS2 ~ ADIS0 ) : Analog Input Pin Select ADIS2 ADIS1 ADIS0 Analog Input Pin 0 0 0 AD0 0 0 1 AD1 0 1 0 AD2 0 1 1 AD3 1 0 0 AD4 1 0 1 AD5 1 1 0 AD6 1 1 1 AD7 Bank 1 RC ADIC (AD Input Pin Control) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADE7 ADE6 ADE5 ADE4 ADE3 ADE2 ADE1 ADE0 Bit 7 ~ Bit 0 ( ADE7 ~ ADE0 ) : AD input pin enable control. ADEx = “0” : Port 9.x functions as I/O pin ADEx = “1” : Port 9.x functions as analog input pin Bank 1 RD ADDH (AD High 8-bit Data Buffer) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADD9 ADD8 ADD7 ADD6 ADD5 ADD4 ADD3 ADD2 Bit 7 ~ Bit 0 ( ADD9 ~ ADD2 ) : AD high 8-bit data buffer Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 13 EM78P311N 8-Bit Microcontroller Bank 1 RE TBKTC (TBT/Keytone Control) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TEN TCK1 TCK0 0 TBTEN TBTCK2 TBTCK1 TBTCK0 Bit 7 ( TEN ) : Keytone enable control TEN = “0” : Disable TEN = “1” : Enable Bit 6 ~ Bit 5 ( TCK1 ~ TCK0 ) : Keytone Output Clock Source Select Clock Source ( Normal, Idle ) TCK1 TCK0 0 0 Fc/2 0 1 Fc/2 1 0 Fc/2 1 1 Keytone Output Frequency ( Fc = 8MHz ) 13 0.976kHz 12 1.953kHz 11 3.906kHz 10 7.812kHz Fc/2 Bit 3 ( TBTEN ) : Time Base Timer Enable Control TBTEN = “0” : Disable TBTEN = “1” : Enable Bit 2 ~ Bit 0 ( TBTCK2 ~ TBTCK0 ) : Time Base Timer Clock Source Select TBTCK2 TBTCK1 TBTCK0 0 0 0 Clock Source ( Normal, Idle ) 23 Fc/2 Interrupt Frequency ( Fc = 8MHz ) 0.95Hz 21 0 0 1 Fc/2 0 1 0 Fc/216 122.07Hz 3.81Hz 0 1 1 Fc/214 488.28Hz 1 0 0 Fc/213 976.56Hz 1 0 1 Fc/212 1953.12Hz 1 1 0 Fc/211 3906.25Hz 1 1 1 Fc/2 9 15625Hz Bank 2 R5 URC1 (UART Control Register 1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 URTD8 UMODE1 UMODE0 BRATE2 BRATE1 BRATE0 UTBE TXE Bit 7 ( URTD8 ) : Transmission data Bit 8 Bit 6 ~ Bit 5 ( UMODE1 ~ UMODE0 ) : UART Transmission Mode Select Bit 14 • UMODE1 UMODE0 UART Mode 0 0 Mode1: 7-bits 0 1 Mode2: 8-bits 1 0 Mode3: 9-bits 1 1 Reserved Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Bit 4 ~ Bit 2 ( BRATE2 ~ BRATE1 ) : Transmit Baud Rate Select BRATE2 BRATE1 BRATE0 Baud Rate e.g. Fc=8MHz 0 0 0 Fc/13 38400 0 0 1 Fc/26 19200 0 1 0 Fc/52 9600 0 1 1 Fc/104 4800 1 0 0 Fc/208 2400 1 0 1 Fc/416 1200 1 1 0 TC4 - 1 1 1 reserved - Bit 1 ( UTBE ): UART transfer buffer empty flag. Set to 1 when transfer buffer is empty. Reset to 0 automatically when writing into the URTD register. UTBE bit will be cleared by hardware when enabling the transmission. UTBE bit is read-only. Therefore, writing to the URTD register is necessary when starting transmission shifting. Bit 0 ( TXE ): Enable transmission TXE = “0” : Disable TXE = “1” : Enable Bank 2 R6 URC2 (UART Control Register 2) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 SBIM1 SBIM0 UINVEN 0 0 0 Bit 5 ~ Bit 4 ( SBIM1 ~ SBIM0 ) : Serial bus interface operation mode select. TC2CK1 TC2CK0 Operation Mode 0 0 I/O mode 0 1 SPI mode 1 0 UART mode 1 1 Reserved Bit 3 ( UINVEN ) : Enable UART TXD and RXD port inverse output. UINVEN = “0” : Disable TXD and RXD port inverse output. UINVEN = “1” : Enable TXD and RXD port inverse output. Bank 2 R7 URS (UART Status Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 URRD8 EVEN PRE PRERR OVERR FMERR URBF RXE Bit 7 ( URRD8 ) : Receiving data Bit 8 Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 15 EM78P311N 8-Bit Microcontroller Bit 6 ( EVEN ) : Select parity check EVEN = “0” : Odd parity EVEN = “1” : Even parity Bit 5 ( PRE ) : Enable parity addition PRE = “0” : Disable PRE = “1” : Enable Bit 4 ( PRERR ) : Parity error flag. Set to 1 when parity error occurred, and cleared to 0 by software. Bit 3 ( OVERR ) : Overrun error flag. Set to 1 when overrun error occurred, and cleared to 0 by software. Bit 2 ( FMERR ) : Framing error flag. Set to 1 when framing error occurred, and cleared to 0 by software. Bit 1 ( URBF ) : UART read buffer full flag. Set to 1 when one character is received. Reset to 0 automatically when read from the URS register. URBF will be cleared by hardware when receiving is enabled. URBF bit is read-only. Therefore, reading the URS register is necessary to avoid an overrun error. Bit 0 ( RXE ) : Enable receiving RXE = “0” : Disable RXE = “1” : Enable Bank 2 R8 URRD (UART Receive Data Buffer) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 URRD7 URRD6 URRD5 URRD4 URRD3 URRD2 URRD1 URRD0 Bit 7 ~ Bit 0 ( URRD7 ~ URRD0 ) : UART receive data buffer. Read only. Bank 2 R9 URTD (UART Transmit Data Buffer) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 URTD 7 URTD 6 URTD 5 URTD 4 URTD 3 URTD 2 URTD 1 URTD0 Bit 7 ~ Bit 0 ( URTD 7 ~ URTD 0) : UART transmit data buffer. Write only. Bank 3 R5 SPIC1 (SPI Control Register 1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SMP DCOL BRS2 BRS1 BRS0 EDS DORD WBE Bit 7 ( SMP ) : SPI data input sample phase. SMP = “0” : Input data sampled at middle of data output time SMP = “1” : Input data sampled at the end of data output time 16 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller In using the external clock, data input sample is fixed at the middle of data output time. Bit 6 ( DCOL ) : SPI Data collision. DCOL = “0” : No occurrence of Data collision DCOL = “1” : Data collision occurred. It should be cleared by software. Bit 5 ~ Bit 3 ( BRS0 ~ BRS2 ) : SPI Clock Source Select BRS2 BRS1 0 BRS0 0 0 ( Fc = 8MHz ) 0.95Kbit/s 11 3.8Kbit/s 10 7.6Kbit/s 8 30.5Kbit/s 6 122Kbit/s 5 Fc/2 0 1 13 Fc/2 1 1 0 Max. Transfer Rate 0 0 0 Clock Source ( Normal, Idle ) Fc/2 1 Fc/2 1 0 0 Fc/2 1 0 1 Fc/2 244Kbit/s 1 1 0 External clock (/SCK pin) Enable /ss pin 1 1 1 External clock (/SCK pin) Disable /ss pin Bit 2 ( EDS ) : Data shift out edge select. EDS = “0” : Rising edge EDS = “1” : Falling edge Bit 1 ( DORD ) : Data transmission order. DORD = “0” : Shift left (MSB first) DORD = “1” : Shift right (LSB first) Bit 0 ( WBE ) : Write buffer empty flag. Read only. WBE = “0” : Write buffer empty WBE = “1” : Not empty, set to “1” automatically when writing data to the data buffer. Bank 3 R6 SPIC2 (SPI Control Register 2) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPIS 0 0 0 0 SPIM1 SPIM0 RBF Bit 7 ( SPIS ) : SPI start shift, set the bit to “1” and shift register starts to shift. It is cleared by hardware when shifting is finished. In transferring the next data, it must be set to “1” again. SPIS = “0” : Finish shifting SPIS = “1” : Start shifting Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 17 EM78P311N 8-Bit Microcontroller Bit 2 ~ Bit 1 ( SPIM1 ~ SPIM0) : SPI Transfer Mode Select TC2CK1 TC2CK0 Transfer Mode 0 0 8-bit Transmit/Receive mode 0 1 8-bit Transmit mode 1 0 8-bit Receive mode 1 1 Reserved Bit 0 ( RBF ) : Set to 1 by Buffer Full Detector, and cleared to 0 automatically when reading data from the SPID register. RBF bit will be cleared by hardware when enabling SPI. And RBF bit is read-only. Therefore, reading the SPRL register is necessary to avoid data collision to occur (DCOL). Bank 3 R7 SPID (SPI Data Buffer) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPID7 SPID6 SPID5 SPID4 SPID3 SPID2 SPID1 SPID0 Bit 7 ~ Bit 0 ( SPID7 ~ SPID0 ) : SPI data buffer. Bank 3 RA PHC1 (Pull High Control Register 1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 - - /PHE81 /PHE80 /PHE63 /PHE62 /PHE61 /PHE60 Bit 5 ~ 4 ( /PHE81 ~ /PHE80 ) : bits 1, 0 of Port 8 Pull high enable bit /PHE8x = “0” : Enable P8x pull high /PHE8x = “1” : Disable P8x pull high Bit 3 ~ 0 ( /PHE63 ~ /PHE60 ) : Bits 3 ~ 0 of Port 6 Pull high enable bit /PHE6x = “0” : Enable P6x pull high /PHE6x = “1” : Disable P6x pull high Bank 3 RB PLC1 (Pull Low Control Register 1) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 - - /PLE81 /PLE80 /PLE63 /PLE62 /PLE61 /PLE60 Bit 5 ~ 4 ( /PLE81 ~ /PLE80 ) : Bits 1, 0 of Port 8 Pull low enable bit /PLE8x = “0” : Enable P8x pull low /PLE8x = “1” : Disable P8x pull low Bit 3 ~ 0 ( /PLE63 ~ /PLE60 ) : bits 3 ~ 0 of Port 6 Pull low enable bit /PLE6x = “0” : Enable P6x pull low /PLE6x = “1” : Disable P6x pull low 18 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Bank 3 RC PHC2 (Pull High Control Register 2) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 - - - - /PHE73 /PHE72 /PHE71 /PHE70 Bit 3 ~ 0 ( /PHE73 ~ /PHE70 ) : bits 3 ~ 0 of Port 7 Pull high enable bit /PHE7x = “0” : Enable P7x pull high /PHE7x = “1” : Disable P7x pull high Bank 3 RD PLC2 (Pull Low Control Register 2) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 - - - - /PLE73 /PLE72 /PLE71 /PLE70 Bit 3 ~ 0 ( /PLE73 ~ /PLE70 ) : bits 3 ~ 0 of Port 7 Pull low enable bit /PLE7x = “0” : Enable P7x pull low /PLE7x = “1” : Disable P7x pull low R10~R1F and R20~R3F (including Banks 0~3) are General Purpose Register 5.3 Special Purpose Registers A (Accumulator) Internal data transfer operation, or instruction operand holding usually involves the temporary storage function of the Accumulator. It is not an addressable register. CONT (Control Register) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 WDTO /INT WDTP1 WDTP0 WDTE PSR2 PSR1 PSR0 The CONT register is both readable and writable. Bit 7 ( WDTO ) : WDT output select WDTO = “0” : Interrupt request WDTO = “1” : Internal reset Bit 6 ( /INT ) : Interrupt enable flag /INT = “0” : masked by DISI or hardware interrupt /INT = “1” : enabled by ENI/RETI instructions Bit 5 ~ Bit 4 ( WDTP1 ~ WDTP0 ): WDT prescaler bits WDTP1 WDTP0 Operating Mode 0 0 1:4 0 1 1 0 1:16 1:64 1 1 1:256 Bit 3 ( WDTE ) : WDT enable control. WDTE = “0” : Disable WDTE = “1” : Enable Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 19 EM78P311N 8-Bit Microcontroller Bit 2 ( PSR2 ) ~ Bit 0 ( PSR0 ) : TCC prescaler bits PSR2 PSR1 PSR0 Operating Mode 0 0 0 1:2 0 0 1 1:4 0 1 0 1:8 0 1 1 1:16 1 0 0 1:32 1 0 1 1:64 1 1 0 1:128 1 1 1 1:256 IOC6 ~ IOC9 − I/O Port Control Register "1" puts the relative I/O pin into high impedance, while "0" defines the relative z I/O pin as output. IOC6 and IOC9 registers are both readable and writable. z INTCR − INT Control Register ( Address : 0Bh ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 INT1NR INT0EN 0 INT3ES1 INT3ES0 0 INT1ES TC2ES Bit 7 ( INT1NR ) : INT1 noise reject time select INT1NR = “0” : Pulses less than 63/fc are eliminated as noise INT1NR = “1” : Pulses less than 15/fc are eliminated as noise Bit 6 ( INT0EN ) : INT0 enable control INT0EN = “0” : General I/O INT0EN = “1” : /INT0 pin Bit 5 : Reserved Bit 4 ~ Bit 3 ( INT3ES1 ~ INT3ES0) : INT3 edge select INT3ES1 INT3ES0 Edge Select 0 0 Rising 0 1 Falling 1 0 Both edge 1 1 Reserved Bit 2: Reserved Bit 1 ( INT1ES ) : INT1 edge select INT1ES = “0” : Rising edge INT1ES = “1” : Falling edge Bit 0 (TC2ES) : Timer/Counter 2 edge select. TC2ES = “0” : Rising edge TC2ES = “1” : Falling edge 20 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller External Interrupt INT Pin Secondary Function Pin Enable Condition /INT0 INT1 P60 P61 ENI + INT0EN (IOCB) ENI + EXIE1 (IMR2) INT3 P80, TC3 ENI + EXIE3 (IMR2) Rising or Falling or Rising/Falling 7/Fc /INT5 P73, /SLEEP ENI + EXIE5 (IMR2) - - Digital Noise Reject Edge Falling Rising or Falling 15/Fc, 63/Fc ADOSCR − AD Offset Control Register ( Address : 0Ch ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CALI SIGN VOF[2] VOF[1] VOF[0] 0 0 0 Bit 7 (CALI) : Calibration enable bit for A/D offset CALI = “0” : disable Calibration CALI = “1” : enable Calibration Bit 6 ( SIGN ) : Offset voltage Polarity bit SIGN = “0” : Negative voltage SIGN = “1” : Positive voltage Bit 5 ~ Bit 3 ( VOF[2] ~ VOF[0] ) : Offset voltage bits IMR1 − Interrupt Mask Register 1 ( Address : 0Eh ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 EXIE5 TCIE2 ADIE 0 EXIE3 TCIE4 SPIE TCIE3 Bit 7 ( EXIE5 ) : External/INT5 pin Interrupt enable bit. EXIE5 = “0” : disable EXIF5 interrupt EXIE5 = “1” : enable EXIF5 interrupt Bit 6 ( TCIE2 ) : Timer/Counter 2 Interrupt enable bit. TCIE2 = “0” : disable TCIF2 interrupt TCIE2 = “1” : enable TCIF2 interrupt Bit 5 ( ADIE ) : ADC complete interrupt enable bit. ADIE = “0” : disable ADIF interrupt ADIE = “1” : enable ADIF interrupt Bit 3 ( EXIE3 ) : External INT3 pin Interrupt enable bit. EXIE3 = “0” : disable EXIF3 interrupt EXIE3 = “1” : enable EXIF3 interrupt Bit 2 ( TCIE4 ) : Timer/Counter 4 Interrupt enable bit. TCIE4 = “0” : disable TCIF4 interrupt TCIE4 = “1” : enable TCIF4 interrupt Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 21 EM78P311N 8-Bit Microcontroller Bit 1 ( SPIE ) : SPI Interrupt enable bit. SPIE = “0” : disable SPIF interrupt SPIE = “1” : enable SPIF interrupt Bit 0 ( TCIE3 ) : Timer/Counter 3 Interrupt enable bit. TCIE3 = “0” : disable TCIF3 interrupt TCIE3 = “1” : enable TCIF3 interrupt Individual interrupt is enabled by setting its associated control bit in the IMR1 to "1". Global interrupt is enabled by the ENI instruction and is disabled by the DISI instruction. The IMR1 register is both readable and writable. IMR2 − Interrupt Mask Register 2( Address: 0Fh ) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 UERRIE URIE UTIE TBIE EXIE1 0 TCIE0 Bit 6 ( UERRIE ) : UART receive error interrupt enable bit. UERRIE = “0” : disable UERRIF interrupt UERRIE = “1” : enable UERRIF interrupt Bit 5 ( URIE ) : UART receive mode interrupt enable bit. URIE = “0” : disable RBFF interrupt URIE = “1” : enable RBFF interrupt Bit 4 ( UTIE ) : UART transmit mode interrupt enable bit. UTIE = “0” : disable TBEF interrupt UTIE = “1” : enable TBEF interrupt Bit 3 ( TBIE ) : Time base timer interrupt enable bit. TBIE = “0” : disable TBIF interrupt TBIE = “1” : enable TBIF interrupt Bit 2 ( EXIE1 ) : External INT 1 Interrupt enable bit. EXIE1 = “0” : disable EXIF1 interrupt EXIE1 = “1” : enable EXIF1 interrupt Bit 0 ( TCIE0 ) : TCC Interrupt enable bit. TCIE0 = “0” : disable TCIF0 interrupt TCIE0 = “1” : enable TCIF0 interrupt Individual interrupt is enabled by setting its associated control bit in the IMR2 to "1". Global interrupt is enabled by the ENI instruction and is disabled by the DISI instruction. The IMR2 register is both readable and writable. 22 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 5.4 CPU Operation Mode Registers for CPU Operation Mode R_BANK Address NAME Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bank 0 0X05 SCR 0 PS2 PS1 PS0 0 1 SIS REM − − − − R/W R/W R/W − − R/W R/W * R_BANK: Register Bank (Bits 7, 6 of R3), R/W: Read/Write Reset Occurs SIS=1 + SLEP SIS=0 + SLEP Idle Mode CPU : Halts Fosc: Oscillates Normal Mode CPU : Operating Fosc: Oscillates Interrupt Sleep Mode CPU : Halts Fosc: Stops /SLEEP Pin Input Fig. 5-4 Operation Mode and Switching Table 2. Mode Switching Control Mode Switch Normal Æ Sleep Sleep Æ Normal Normal Æ Idle Idle Æ Normal Switch Method Note Set SIS = 1, execute SLEP instruction /SLEEP pin wake up Set SIS = 0, execute SLEP instruction − Interrupt − − − Table 3. Operation Mode Operation Mode Signal Clock Frequency CPU Code Reset Normal Turn on Reset Fosc Idle Sleep Turn off Halt On-chip Peripherals Reset Fosc Halt In Normal mode, the CPU core and on-chip peripherals operate in oscillator frequency. In Idle mode, the CPU core halts, but the on-chip peripheral and oscillator circuit remain active. Idle mode is released to Normal mode by any interrupt source. If the ENI instruction is set, an interrupt will be serviced first followed by executing the next instruction which is after the Idle mode is released and the interrupt service is finished. If the ENI instruction is not set, the next instruction will be executed which is after the Idle mode start instruction. Idle mode can also be released by setting the /RESET pin to low and executing a reset operation. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 23 EM78P311N 8-Bit Microcontroller In Sleep mode, the internal oscillator is turned off and all system operation is halted. Sleep mode is released by /SLEEP pin (level sensitive or edge sensitive can be set by System Control Register (SCR) Bit 0 (REM)). After a warm-up period, the next instruction will be executed which is after the Sleep mode start instruction. Sleep mode can also be released by setting the /RESET pin to low and executing a reset operation. In level sensitive mode, the /SLEEP pin must be confirmed in low level before entering Sleep mode. In edge sensitive mode, Sleep mode is started even when the /SLEEP pin is in high level. Table 4. Wake-up Methods Wake-up Signal Sleep Mode R5 (SIS) = 1+SLEP Instruction 1. Individual interrupt source in IMR1, IMR2 2. WDT interrupt request 3. /INT0 4. ENI instruction is not executed Idle Mode R5 (SIS)= 0 + SLEP Instruction 1. Wake-up 2. Jump to the next instruction or enter Idle mode No effect ** (**) Normal Mode R5 (SIS)=(*) No effect** 1. Wake-up 2. Jump to an Interrupt vector after RETI Interrupt instruction, then jump to the next instruction or enter Idle mode 1. Individual interrupt source in IMR1, IMR2 2. WDT interrupt request 3. /INT0 4. Execute ENI instruction No effect ** /SLEEP pin 1. Wake-up 2. Jump to the next No effect instruction or enter Sleep mode No effect /RESET pin Reset Reset Reset WDT time out Reset Reset Reset Note: * Don’t care ** Interrupt request flag will be recorded 5.5 AD Converter Registers for AD Converter Circuit R_BANK Address NAME Bank 1 Bank 1 Bank 1 Bank 1 Bank 0 SPR SPR Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADP ADIS2 ADIS1 ADIS0 0X0B ADCR R/W R/W R/W R/W R/W R/W R/W R/W 0X0C ADIC ADE7 ADE6 ADE5 ADE4 ADE3 ADE2 ADE1 ADE0 R/W R/W R/W R/W R/W R/W R/W R/W 0X0D ADDH ADD9 ADD8 ADD7 ADD6 ADD5 ADD4 ADD3 ADD2 R R R R R R R R 0X08 ADDL ADD1 ADD0 0 TC2M TC2S R R -- R/W R/W R/W R/W R/W 0x0E ISFR1 EXIF5 TCIF2 ADIF 0 EXIF3 TCIF4 SPIF TCIF3 R/W 0 R/W R/W R/W R/W 0 0 0 0x0C 0x0E ADREF ADRUN ADCK1 ADCK0 R/W R/W ADOSCR CALI SIGN R/W R/W R/W EXIE5 TCIE2 R/W R/W IMR1 VOF[2] VOF[1] VOF[0] TC2CK2 TC2CK1 TC2CK0 R/W R/W -- -- -- ADIE 0 EXIE3 TCIE4 SPIE TCIE3 R/W 0 R/W R/W R/W R/W * R_BANK : Register Bank (Bits 7, 6 of R3), R/W: Read / Write * SPR : Special Purpose Registers 24 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller AD7 (P97) AD6 (P96) VDD 8 to 1 Analog switch AD5 (P95) AD4 (P94) AD3 (P93) AD2 (P92) VREF ADC (Successive Approximation) Power Down Start to Convert Fosc/4 AD1 (P91) Fosc/16 Fosc/32 4 to 1 MUX AD0 (P90) 7-0 ADIC 2 1 0 ADCR 5 4 ADCR 5 5 ISFR1 9 8 7 6 5 4 3 2 1 0 IMR1 6 3 7 ADCR DATA BUS Fig. 5-5 AD Converter It is a 10-bit successive approximation type AD converter. The upper side of analog reference voltage can select either internal VDD or external input pin P97 (VREF) by setting the ADREF bit in ADCR. ADC Data Register When the A/D conversion is completed, the result is loaded to the ADDH (8 bit) and ADDL (2 bit). The START/END bit is cleared, and the ADIF is set. A/D Sampling Time The accuracy, linearity, and speed of the successive approximation A/D converter are dependent on the properties of the ADC. The source impedance and the internal sampling impedance directly affect the time required to charge the sample holding capacitor. The application program controls the length of the sample time to meet the specified accuracy. Generally speaking, the program should wait for 2 μs for each KΩ of the analog source impedance and at least 2 μs for the low-impedance source. The maximum recommended impedance for the analog source is 10KΩ at VDD =5V. After the analog input channel is selected, this acquisition time must be done before A/D conversion can be started. A/D Conversion Time ADCK0 and ADCK1 select the conversion time (Tct), in terms of instruction cycles. This allows the MCU to run at maximum frequency without sacrificing accuracy of A/D conversion. For the EM78P311N, the conversion time per bit is about 4μs. Table 5 shows the relationship between Tct and the maximum operating frequencies. Table 5 ADCK1:0 Operation Mode Max. Frequency (Fc) Max. Conversion Rate per Bit Max. Conversion Rate 00 01 Fc/4 Fc/16 1MHz 4MHz 250kHz (4μs) 250kHz (4μs) 48μs (20.8kHz) 48μs (20.8kHz) 10 11 Fc/32 Reserved 8MHz - 250kHz (4μs) - 48μs (20.8kHz) - Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 25 EM78P311N 8-Bit Microcontroller 5.6 Time Base Timer and Keytone Generator Registers for AD Converter Circuit R_BANK Address Name Bit 7 Bit 6 Bit 5 Bit 4 TEN TCK1 TCK0 0 R/W R/W R/W -- R/W R/W R/W R/W TBEF TBIF EXIF1 0 TCIF0 Bank 1 0X0E Bank 0 0x0F SPR 0x0F Bit 3 Bit 2 Bit 1 Bit 0 TBTEN TBTCK2 TBTCK1 TBTCK0 TBKTC 0 ISFR2 IMR2 UERRIF RBFF 0 R/W R/W R/W R/W R/W 0 R/W 0 UERRIE URIE UTIE TBIE EXIE1 0 TCIE0 0 R/W R/W R/W R/W R/W 0 R/W Output Enable (P63) Output Latch D Data Output Q /TONE Pin 13 Fosc/2 12 Fosc/2 MUX 11 Fosc/2 10 Fosc/2 TCK1:0 TEN 2 TBKTC Fig. 5-6 Tone Output Pin Configuration The Keytone output can generate 50% duty pulse for driving a piezo-electric buzzer. The P63 must be set to “1” before the keytone is enabled and it can be halted by setting P63 to “0”. P63 TEN TONE Pin Fig. 5-7 Tone Output Pin Timing Chart 26 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 23 Fosc/2 21 Fosc/2 16 Fosc/2 14 Fosc/2 13 Fosc/2 MUX Falling Edge Detector 12 Fosc/2 TBT Interrupt 11 Fosc/2 Fosc/2 9 TBTEN TBTCK2:0 3 TBKTC Fig. 5-8 TBT Configuration The Time Base Timer is used to generate the base time for key scan or dynamic display processing. The interrupt is generated in the first falling edge of the source clock after TBTEN is set to “1”. Source Clock TBTEN TBT Interrupt Fig. 5-9 Time Base Timer Timing Chart Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 27 EM78P311N 8-Bit Microcontroller 5.7 UART (Universal Asynchronous Receiver/Transmitter) Registers for UART Circuit R_BANK Address Name Bit 7 Bank 2 0X05 URC1 Bank 2 0X06 URC2 Bank 2 0X07 URS Bank 2 0X08 URRD Bank 2 0X09 URTD Bank 0 0x0F ISFR2 SFR 0x0F IMR2 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 URTD8 UMODE1 UMODE0 BRATE2 BRATE1 BRATE0 Bit 1 Bit 0 UTBE TXE R/W R/W R/W R/W R/W R/W R R/W 0 0 SBIM1 SBIM0 UINVEN 0 0 0 R/W R/W -- -- -- R/W URRD8 EVEN PRE R/W R/W R/W R/W R/W URRD5 URRD4 R R URRD7 URRD6 R R URTD 7 URTD 6 -- -- URBF RXE R/W R R/W URRD3 URRD2 URRD1 URRD0 R R R R PRERR OVERR FMERR URTD 5 URTD 4 URTD 3 URTD 2 URTD 1 W W W W W W URTD0 W W 0 UERRIF RBFF TBEF TBIF EXIF1 0 TCIF0 -- R/W R/W R/W R/W R/W -- R/W 0 UERRIE URIE UTIE TBIE EXIE1 0 TCIE0 -- R/W R/W R/W R/W R/W -- R/W TC4 RXE Selector Fsystem Baud rate generator RX Control Interrupt Control RX shift register Parity control TX Control TXE RX UINVEN URRD8 URRD Error flag TX URTD8 URTD UINVEN Data Bus Fig. 5-10 Function Block Diagram In Universal Asynchronous Receiver Transmitter (UART), each transmitted or received character is individually synchronized by framing it with a start bit and stop bit. Full duplex data transfer is possible since the UART has independent transmit and receive sections. Double buffering for both sections allows the UART to be programmed for continuous data transfer. 28 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller The figure below shows the general format of one character sent or received. The communication channel is normally held in the marked state (high). Character transmission or reception starts with a transition to the space state (low). The first bit transmitted or received is the start bit (low). It is followed by the data bits, in which the least significant bit (LSB) comes first. The data bits are followed by the parity bit. If present, then the stop bit or bits (high) confirm the end of the frame. In receiving, the UART synchronizes on the falling edge of the start bit. When two or three “0” are detected during three samples, it is recognized as normal start bit and the receiving operation is started. START bit D0 D1 D2 1 bit Dn 7 or 8 bits Idle state (mark) Parity STOP bit bit 1 bit 1 bits One character or frame I Fig. 5-11 Data Format in UART 5.7.1 UART Mode There are three UART modes. Mode 1 (7 bits data) and Mode 2 (8 bits data) allow the addition of a parity bit. The parity bit addition is not available in Mode 3. The Figure below shows the data format in each mode. UMODE Mode 1 Mode 2 Mode 3 PRE 1 2 3 4 5 6 7 8 9 10 11 0 0 0 START 7 bits DATA 0 0 1 START 7 bits DATA 0 1 0 START 8 bits DATA STOP 0 1 1 START 8 bits DATA Parity STOP 1 0 X START 9 bits DATA STOP STOP Parity STOP Fig. 5-12 UART Mode 5.7.2 Transmitting In transmitting serial data, the UART operates as follows: 1. Set the TXE bit of the URC1 register to enable the UART transmission function. 2. Write data into the URTD register and the UTBE bit of the URC1 register will be set by hardware. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 29 EM78P311N 8-Bit Microcontroller 3. Start transmitting. 4. Serially transmitted data are transmitted in the following order from the TX pin. 5. Start bit: one “0” bit is output. 6. Transmit data: 7, 8 or 9 bits data are output from the LSB to the MSB. 7. Parity bit: one parity bit (odd or even selectable) is output. 8. Stop bit: one “1” bit (stop bit) is output. Mark state: output “1” continues until the start bit of the next transmitted data. After transmitting the stop bit, the UART generates a TBEF interrupt (if enabled). 5.7.3 Receiving In receiving, the UART operates as follows: 1. Set RXE bit of the URS register to enable the UART receiving function. The UART monitors the RX pin and synchronizes internally when it detects a start bit. 2. Receive data is shifted into the URRD register in the order from LSB to MSB. 3. The parity bit and the stop bit are received. After one character received, the UART generates a RBFF interrupt (if enable). And URBF bit of URS register will be set to 1. 4. The UART makes the following checks: (a) Parity check: The number of 1 of the received data must match the even or odd parity setting of the EVEN bit in the URS register. (b) Frame check: The start bit must be 0 and the stop bit must be 1. (c) Overrun check: The URBF bit of the URS register must be cleared (that means the URRD register should be read out) before next received data is loaded into the URRD register. If any checks failed, the UERRIF interrupt will be generated (if enabled), and an error flag is indicated in PRERR, OVERR or FMERR bit. The error flag should be cleared by software else the UERRIF interrupt will occur when the next byte is received. 5. Read received data from URRD register. And URBF bit will be clear by hardware. 5.7.4 Baud Rate Generator The baud rate generator is comprised of a circuit that generates a clock pulse to determine the transfer speed for transmission/reception in the UART. The BRATE2~BRATE0 bits of the URC1 register can determine the desired baud rate. 30 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 5.8 SPI (Serial Peripheral Interface) Registers for the SPI Circuit R_BANK Address Name Bank 3 0X05 SPIC1 Bank 3 0X06 SPIC2 Bank 3 0X07 SPID Bank 0 SFR 0x0E ISFR1 0x0E IMR1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SMP DCOL BRS2 BRS1 BRS0 EDS DORD WBE R/W R/W R/W R/W R/W R/W R/W R SPIS 0 0 0 0 SPIM1 SPIM0 RBF R/W -- -- -- -- R/W R/W R SPID7 SPID6 SPID5 SPID4 SPID3 SPID2 SPID1 SPID0 R/W R/W R/W R/W R/W R/W R/W R/W EXIF5 TCIF2 ADIF 0 EXIF3 TCIF4 SPIF TCIF3 R/W R/W R/W -- R/W R/W R/W R/W EXIE5 TCIE2 ADIE 0 EXIE3 TCIE4 SPIE TCIE3 R/W R/W R/W -- R/W R/W R/W R/W RBFI DCOL RBF SE Set to 1 Clear Collision Detector Buffer Full Detector Tx Empty Detector SHIFT Register SPID (8 bits) reg SDI TLS0~1 DORD SMP 2 SDO Master/Slave EDS Edge Select BRS2~0 3 /SS /SS enable Tsystem BRS2~0 3 Prescaler 4, 16, 64, 256,1024 SE Edge Select EDS TC1/2 SCK Fig. 5-13 SPI Block Diagram The serial interface are connected to external devices via P70 (/SCK), P71 (SI), P72 (SO). The serial interface can also be used as I/O port. In the transmit mode, P71 can be used as normal I/O port and in receive mode, P72 and P71 can be used as normal I/O ports. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 31 EM78P311N 8-Bit Microcontroller 5.8.1 Serial Clock Six internal clocks can be selected by setting BRS0 ~ BRS2 and the clock output to the outside from /SCK (P70) pin. The External clock can also be used and connected to /SCK (P70) pin. 5.8.2 Shift Direction and Sample Phase Setting up the DORD bit of the SPIC1 register can determine the shift direction. Setting up the EDS bit of the SPIC1 register can select the rising edge or falling edge and latch the data. Setting up the SMP bit of the SPIC2 register can select the sample phase at the middle or at the end of the data output time. 5.8.3 Transfer Mode The transmit, receive, transmit/receive mode can be selected by setting SPIM0 ~ SPIM1. (a) 8-bit Transmit Mode: Set SPIM0 ~ SPIM12 to transmit mode and write data to the data buffer SPID. Set SPIS to “1” to start transmission. The data are output sequentially to the SO pin in synchronous with the serial clock. When the final bit of transfer data has been transferred, the SPI interrupt is generated and SPIS is cleared to “0” by hardware. In order to transmit the next data, the SPIS must be set to “1” again by software. If the next data is not written to the data buffer, the transfer is not started when using the internal clock. shift start shift start SPIS RBF WBE SO pin shift finish a0 a1 a2 a3 a4 a5 a6 a7 b0 b1 b2 b3 b4 b5 b6 b7 SPIF SPID a b write data write data Fig. 5-14 Transmit Mode (8-bit, 1 word) 32 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller (b) 8-bit Receive Mode: Setting SPIM0 ~ SPIM1 to receive mode and setting SPIS to “1” to start receiving. The data are input sequentially from the SI pin in synchronous with the serial clock. When the final bit of transfer data has been received, the SPI interrupt is generated and SPIS is cleared to “0” by hardware. In order to receive the next data, the SPIS must be set to “1” again by software. If the current data is not read out from the data buffer, receiving is not started when using internal clock. shift start shift start shift finish RBF WBE /SCK pin SI pin a0 a1 a2 a3 a4 a5 a6 a7 b0 b1 b2 b3 b4 b5 b6 b7 SPIF SPID a read data b read data Fig. 5-15 Receive Mode (8-bit, 1 word) (c) 8-bit Transmit/Receive Mode Set SPIM0 ~ SPIM1 to transmit/receive mode and write data to data buffer SPID. Set SPIS to “1” to start transferring. The data are output to the SO pin and input from the SI pin sequentially in synchronous with the serial clock. When the number of data words specified has been transferred, the SPI interrupt is generated and SPIS is cleared to “0” by hardware. In order to receive the next data, the SPIS must be set to “1” again by software. Writing data in transmit mode and reading data in receive mode use the same data buffer. If the current data is not read out from the data buffer and then write the data to data buffer, the transfer is not started when using internal clock. Always write the data to be transmitted after reading the received data. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 33 EM78P311N 8-Bit Microcontroller shift start shift start SPIS RBF shift finish WBE shift finish /SCK pin SO pin a0 a1 a2 a3 a4 a5 a6 a7 b0 b1 b2 b3 b4 b5 b6 b7 SI pin c0 c1 c2 c3 c4 c5 c6 c7 d0 d1 d2 d3 d4 d5 d6 d7 SPIF SPID a c write data d b read data write data read data Fig. 5-16 Transmit/Receive Mode (8-bit, 1 word) (d) Multiple Device Connect (/SS): When selecting external clock for transfer clock source, the /SS function can be used. This pin (/SS) will be active when the /SS function is enabled, else the /SS pin is a general purpose I/O. Ignore the data on the SDI and SDO pins while /SS is high, since the SDO is no longer driven. SDO SDI SCK /SS Master P.67 P67 P66 PP65 65 PP64 64 /SS SDO SCK SDI SDI Slave Device 1 /SS SDO SCK SDI SDI Slave Device 2 /SS SDO SCK SDI SDI Slave Device 3 /SS SDO SCK SDI SDI Slave Device 4 Fig. 5-17 The SPI Configuration Example of Single-Master and Multi-Slaves 34 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 5.9 Timer/Counter 2 Registers for Timer/Counter 2 Circuit R_BANK Address Name Bank 1 0X08 TC2CR Bank 1 0X09 TC2DH Bank 1 0X0A TC2DL Bank 0 0x0E ISFR1 SFR 0x0B INTCR SFR 0x0E IMR1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADD1 ADD0 0 TC2M TC2S TC2CK2 TC2CK1 TC2CK0 R R -- R/W R/W R/W R/W R/W TC2D15 TC2D14 TC2D13 TC2D12 TC2D11 TC2D10 TC2D9 TC2D8 R/W R/W R/W R/W R/W R/W R/W R/W TC2D7 TC2D6 TC2D5 TC2D4 TC2D3 TC2D2 TC2D1 TC2D0 R/W R/W R/W R/W R/W R/W R/W R/W EXIF5 TCIF2 ADIF 0 EXIF3 TCIF4 SPIF TCIF3 R/W R/W R/W -- R/W R/W R/W R/W INT1NR INT0EN 0 0 INT1ES TC2ES R/W R/W R/W R/W EXIE5 TCIE2 R/W R/W INT3ES1 INT3ES0 R/W R/W ADIE 0 EXIE3 TCIE4 SPIE TCIE3 R/W -- R/W R/W R/W R/W TC2ES TC2 Pin M Window 23 fc/2 13 fc/2 8 fc/2 3 fc/2 fc 16-bit Up-counter MUX Clear Comparator TC2CK 3 TC2 Interrupt TC2S TC2CR TCR2H TCR2L Fig. 5-18 Configuration of Timer/Counter 2 Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 35 EM78P311N 8-Bit Microcontroller 5.9.1 Timer Mode In Timer mode, counting up is performed using the internal clock. When the contents of the up-counter matched with the TCR2 (TCR2H+TCR2L), then interrupt is generated and the counter is cleared. Counting up resumes after the counter is cleared. Internal clock Up-counter 0 TCR2 1 2 3 4 5 n-3 n-2 n-1 n 0 n 2 1 3 counter clear match TC2 interrupt Fig. 5-19 Timer Mode Timing Chart 5.9.2 Counter Mode In Counter mode, counting up is performed using the external clock input pin (TC2 pin) and either rising or falling can be selected by setting TC2ES. When the contents of the up-counter matched with the TCR2 (TCR2H+TCR2L), then interrupt is generated and the counter is cleared. Counting up resumes after the counter is cleared. TC2 Pin Up-counter TCR2 0 1 2 3 4 n-2 n-1 n 0 n match 1 2 3 counter clear TC2 interrupt Fig. 5-20 Counter Mode Timing Chart (TC2ES = 1) 5.9.3 Window Mode In Window mode, counting up is performed on the rising or falling edge of the pulse that is logical AND of an internal clock and the TC2 pin (window pulse). When the contents of the up-counter matched with the TCR2 (TCR2H+TCR2L), then interrupt is generated and the counter is cleared. The frequency (window pulse) must be slower than the selected internal clock. Writing to the TCR2L, the comparison is inhibited until TCR2H is written. 36 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller TC2 pin Internal clock Up-counter 0 TCR2 1 2 n-3 n-1 n-2 n match n 0 1 2 3 counter clear TC2 interrupt Fig. 5-21 Window Mode Timing Chart 5.10 Timer/Counter 3 Registers for Timer/Counter 3 Circuit R_BANK Address Name Bank 1 0X05 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TC3CAP TC3S TC3CK1 TC3CK0 TC3M 0 0 0 R/W R/W R/W R/W R/W -- -- -- TC3DA5 TC3DA4 TC3DA3 TC3DA2 TC3DA1 TC3DA0 R/W R/W R/W R/W R/W R/W TC3DB5 TC3DB4 TC3DB3 TC3DB2 TC3DB1 TC3DB0 TC3CR TC3DA7 TC3DA6 Bank 1 0X06 TC3DA Bank 1 0X07 TC3DB Bank 0 0x0E ISFR1 R/W R/W TC3DB7 TC3DB6 SFR 0x0B INTCR SFR 0x0E IMR1 R/W R/W R/W R/W R/W R/W R/W R/W EXIF5 TCIF2 ADIF 0 EXIF3 TCIF4 SPIF TCIF3 -- R/W R/W R/W R/W 0 INT1ES TC2ES R/W R/W R/W INT1NR INT0EN 0 R/W R/W -- R/W R/W -- R/W R/W EXIE5 TCIE2 ADIE 0 EXIE3 TCIE4 SPIE TCIE3 R/W R/W R/W -- R/W R/W R/W R/W Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) INT3ES1 INT3ES0 • 37 EM78P311N 8-Bit Microcontroller INT3ES Edge Detector Rising Inhibit Falling Capture Control TC3 Interrupt TC3M TC3 pin M fc/2 , fs/2 10 2 fc/2 , fs/2 7 fc/2 12 4 MUX 8-bit Up-counter Overflow TC3S TC2CK Comparator CAP 2 Capture Capture TC3CR TCR3B TCR3A Fig. 5-22 Configuration of Timer/Counter3 5.10.1 Timer Mode In Timer mode, counting up is performed using the internal clock. When the contents of the up-counter matched with the TCR3DA, then interrupt is generated and the counter is cleared. Counting up resumes after the counter is cleared. The current contents of the up-counter are loaded into the TCR3DB by setting TC3CAP to “1” and the TC3CAP is cleared to “0” after capture automatically. 5.10.2 Counter Mode In Counter mode, counting up is performed using the external clock input pin (TC3 pin) and either rising or falling edge can be selected by INT3ES0 but both edge cannot be used. When the contents of the up-counter matched with the TCR3DA, then interrupt is generated and the counter is cleared. Counting up resumes after the counter is cleared. The current contents of the up-counter are loaded into the TCR3DB by setting TC3CAP to “1” and the TC3CAP is cleared to “0” after capture automatically. 5.10.3 Capture Mode In Capture mode, the pulse width, period and duty of the TC3 input pin are measured in this mode, which can be used in decoding the remote control signal. The counter is free running by the internal clock. On the rising (falling) edge of TC3 pin input, the contents of the counter is loaded into TCR3DA, then the counter is cleared and interrupt is generated. On the falling (rising) edge of TC3 pin input, the contents of the counter are loaded into TCR3DB. The counter is still counting, on the next rising edge 38 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller of the TC3 pin input, the contents of the counter are loaded into TCR3A, counter is cleared and interrupt is generated again. If an overflow before the edge is detected, the FFH is loaded into TCR3DA and an overflow interrupt is generated. During interrupt processing, it can be determined whether or not there is an overflow by checking whether the TCR3DA value is FFH. After an interrupt (capture to TCR3DA or overflow detection) is generated, capture and overflow detection are halted until TCR3DA is read out. Source Clock Up-counter K-2 K-1 K 0 1 m-1 m m+1 n-1 n 0 1 2 3 FE FF0 1 2 3 TC3 Pin Input TCR3DA K n TCR3DB FF (Overflow) m FE Capture TC3 Interrupt Overflow Capture Reading TCR3DA Fig. 5-23 Timing Chart of Capture Mode 5.11 Timer/Counter 4 Registers for Timer 4 Circuit R_BANK Address Name Bank 0 0X0B Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 TC4FF1 TC4FF0 TC4S R/W R/W R/W R/W R/W TC4D7 TC4D6 TC4D5 TC4D4 R/W R/W R/W EXIF5 TCIF2 R/W Bit 2 Bit 1 Bit 0 TC4M1 TC4M0 R/W R/W R/W TC4D3 TC4D2 TC4D1 TC4D0 R/W R/W R/W R/W R/W ADIF 0 EXIF3 TCIF4 SPIF TCIF3 R/W R/W -- R/W R/W R/W R/W EXIE5 TCIE2 ADIE 0 EXIE3 TCIE4 SPIE TCIE3 R/W R/W R/W -- R/W R/W R/W R/W TC4CK2 TC4CK1 TC4CK0 TC4CR Bank 0 0X0C TC4D Bank 0 0x0E ISFR1 SFR 0x0E IMR1 Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 39 EM78P311N 8-Bit Microcontroller TC4FF TC4M (1,1) 11 fc/2 7 fc/2 3 fc/2 TC4 pin Clear MUX TC4 Interrupt F/F Clear Set Q Toggle TC4M(1,*) 8-bit Up-counter /PWM, /PDO Pin Overflow Match Comparator TC4CK 3 TC4S TCR4 TC4CR Fig. 5-24 Timer/Counter 4 Configuration 5.11.1 Timer Mode In Timer mode, counting up is performed using the internal clock. When the contents of the up-counter matched with the TCR4, then interrupt is generated and the counter is cleared. Counting up resumes after the counter is cleared. 5.11.2 Counter Mode In Counter mode, counting up is performed on the rising edge of the external clock input pin (TC4 pin). When the contents of the up-counter matched with the TCR4, then interrupt is generated and the counter is cleared. Counting up resumes after the counter is cleared. 5.11.3 PDO Mode In Programmable Divider Output (PDO) mode, counting up is performed using the internal clock. The contents of TCR4 are compared with the contents of the up-counter. The F/F output is toggled and the counter is cleared each time a match is found. The F/F output is inverted and output to /PDO pin. This mode can generate 50% duty pulse output. The F/F can be initialized by the program and it is initialized to “0” during a reset. A TC4 interrupt is generated each time the /PDO output is toggled. Source Clock Up-counter TCR4 0 1 2 3 n-1 n 0 1 n-1 n 0 1 n-1 n 0 1 2 n F/F /PDO Pin TC4 Interrupt Fig. 5-25 Timing Chart for PDO Mode 40 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 5.11.4 PWM Mode In Pulse Width Modulation (PWM) Output mode, counting up is performed using the internal clock. The contents of the TCR4 are compared with the contents of the up-counter. The F/F is toggled when match is found. The counter is still counting, the F/F is toggled again when the counter overflows, then the counter is cleared. The F/F output is inverted and output to the /PWM pin. A TC4 interrupt is generated each time an overflow occurs. TCR4 is configured as a 2-stage shift register and, during output, will not switch until one output cycle is completed even if TCR4 is overwritten. Therefore, the output can be changed continuously. TRC4 is also shifted the first time by setting TC4S to “1” after data is loaded to TCR4. Source Clock Up-counter TCR4 0 1 n-1 n n+1 n+2 FE n/n FF 0 n-1 n n+1 n+2 FE n/m Match F/F Overflow FF 0 1 m-1 m m/m Match Overwrite Overflow Shift /PWM 1 Period TC4 Interrupt Fig. 5-26 Timing Chart for PWM Mode 5.12 TCC/WDT & Prescaler An 8-bit counter is available as prescaler for the TCC. The PSR0~PSR2 bits determine the ratio. The prescaler is cleared each time the instruction is written to TCC under TCC mode. R1 (TCC) is an 8-bit timer/counter. The clock source of TCC is the internal clock. If the TCC signal source is from the internal clock, TCC will increase by 1 at every instruction cycle (without prescaler). CLK=Fosc/2 or CLK=Fosc/4 selection is determined by the CODE Option bit CLK status. CLK=Fosc/2 is used if CLK bit is "0", and CLK=Fosc/4 is used if CLK bit is "1". The watchdog timer is a free running on-chip RC oscillator. During normal operation mode, a WDT time-out (if enabled) will cause the device to reset or interrupt by setting WDTO. The WDT can be enabled or disabled any time during normal mode by software programming. Without prescaler, the WDT time-out period is approximately 18 ms (default). The WDT can also be used as a timer to generate an interrupt at fixed interval. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 41 EM78P311N 8-Bit Microcontroller 5.13 I/O Ports The I/O registers, Port 6, Port 7, Port 8, and Port 9 are bi-directional tri-state I/O ports. Each I/O pin can be defined as “input” or “output” pin by the I/O control register (IOC6 ~ IOC9). The I/O registers and I/O control registers are both readable and writable. The I/O interface circuits for Port 6, Port 7, Port 8, and Port 9 are shown in Fig. 5-26. PCRD Q PORT 0 1 P R D CLK Q C L Q P R Q C CLK L PCW R IOD D M U X PDW R PDRD Fig. 5-27 The I/O Port and I/O Control Register Circuit 5.14 Reset and Wake-up 5.14.1 Reset A reset is initiated by one of the following events: (1) Power-on reset (2) /RESET pin input “low” (3) WDT timeout. (if enabled) 1 The device is kept in a reset condition for a period of approx. 18ms (one oscillator start-up timer period) after the reset is detected. Once a RESET occurs, the following functions are performed. 1 42 • The oscillator starts or is running The Program Counter (R2) is reset to all “0”. When power is switched on, the upper two bits of R3, the upper two bits of R4 and the Bits 6 ~ 4 of R5 are cleared. All I/O port pins are configured as input mode (high-impedance state). NOTE: VDD = 5V, set up time period = 16.2ms ± 30% VDD = 3V, set up time period = 19.6ms ± 30% Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller The Watchdog timer and prescaler are cleared. Upon power on, the upper two bits of R3 are cleared. Upon power on, the upper two bits of R4 are cleared. Upon power on, the upper three bits of R5 are cleared. The bits of CONT register are set to all “1” except bit 6 (INT flag). ISFR0, ISFR1, ISFR2 register and IMR1, IMR2 registers are cleared. The controller has two modes for power saving. (1) SLEEP mode: R5 (SIS) = 1, SLEP instruction. The internal oscillator is turned off and all system operation is halted. (2) Idle mode: R5 (SIS) = 0, SLEP instruction The CPU core halts but the on-chip peripheral and oscillator circuit remain active. 5.14.2 Wake-up from Sleep Mode (1) External /SLEEP pin The controller will be waken up and execute the next instruction after entering Sleep mode. All the registers will maintain their original values before “SLEP” instruction was executed. (2) /RESET pin pull low This will reset the controller and starts the program at address zero. (3) WDT time out This will reset the controller and run the program at address zero. 5.14.3 Wake-up from Idle Mode (1) All interrupt In all these cases, user should always enable the circuit before entering Idle mode. After wake-up, all registers will maintain their original values before entering “SLEP” instruction, then service an interrupt subroutine or proceed with next instruction by setting individual interrupt enable bit. After servicing an interrupt sub-routine (“RETI” instruction), the program will jump from “SLEP” instruction to the next instruction. (2) /RESET pin pull low This will reset the controller and run the program at address zero. (3) WDT time out This will reset the controller and run the program at address zero. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 43 EM78P311N 8-Bit Microcontroller Table 6. Summary of the Initialized Values for Registers Address Name Reset Type Bit Name 0x06 Power-on IOC6 /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-Up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-Up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on 0x07 IOC7 0x08 IOC8 0x09 IOC9 0x0B INTCR 0x0C ADOSC R 0x0E IMR1 0x0F IMR2 N/A CONT 0x00 R0 (IAR) /RESET and WDT time out 0x01 0x02 0x03 0x04 44 • Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 C67 C66 C65 C64 C63 C62 C61 C60 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 P X U U U X U U U C97 1 1 P INT1NR 0 0 P CALI 0 0 0 EXIE5 0 0 P X U U U WDT0 0 0 P U P P P P P P P X X X C73 C72 C71 C70 U U U 1 1 1 1 U U U 1 1 1 1 U U U P P P P X X X X X C81 C80 U U U U U 1 1 U U U U U 1 1 U U U U U P P C96 C95 C94 C93 C92 C91 C90 1 1 1 1 1 1 1 1 1 1 1 1 1 1 P P P P P P P INT0EN X X INT1ES TC2ES INT3ES1 INT3ES0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 P P P P P P P SIGN VOF2 VOF1 VOF0 X X X 0 0 0 0 U U U P P P P U U U P P P P U U U TCIE2 ADIE X EXIE3 TCIE4 SPIE TCIE3 0 0 U 0 0 0 0 0 0 U 0 0 0 0 P P U P P P P UTIE TBIE EXIE1 X TCIE0 UERRIE URIE 0 0 0 0 0 U 0 0 0 0 0 0 U 0 P P P P P U P /INT WDTP1 WDTP0 WDTE PSR2 PSR1 PSR0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 P P P P P P P U U U U U U U P P P P P P P P P Wake-up from Sleep, Idle mode P P P P P P P Bit Name - - - - - - - - Power-on 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 P R1 (TCC) /RESET and WDT time out R2 (PC) Bit 7 Wake-up from Sleep, Idle mode P P P P P P P Bit Name - - - - - - - - Power-on 0 0 0 0 0 0 0 0 /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name R3 Power-on (SR) /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name R4 Power-on (RSR) /RESET and WDT time out Wake-Up from Sleep, Idle mode 0 0 0 0 0 0 0 Jump to interrupt vector or execute next instruction RBS1 RBS0 X T P Z DC 0 0 0 1 1 U U 0 0 0 t t P P P P P t t P P X GRBS0 RSR5 RSR4 RSR3 RSR2 RSR1 0 0 U U U U U 0 0 P P P P P P P P P P P P 0 C U P P RSR0 U P P Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Register Bank 0 Address Name 0x05 0x06 0x07 0x08 0x09 SCR Port 6 Port 7 Port 8 Port 9 Reset Type Bit 7 Bit 6 Bit 5 Bit 4 Bit Name X X X PS0 Power-on U 0 0 0 /RESET and WDT time out U 0 0 0 Wake-up from Sleep, Idle mode U P P Bit Name P67 P66 Power-on 1 1 /RESET and WDT time out 1 Wake-up from Sleep, Idle mode P TC4CR 0X0D 0X0E 0X0F TC4D ISFR0 ISFR1 ISFR2 Bit 1 Bit 0 X X SIS REM U U 0 0 U U 0 0 P U U P P P65 P64 P63 P62 P61 P60 1 1 1 1 1 1 1 1 1 1 1 1 1 P P P P P P P X X X X P73 P72 P71 P70 Power-on U U U U 1 1 1 1 /RESET and WDT time out U U U U 1 1 1 1 Wake-up from Sleep, Idle mode U U U U P P P P Bit Name X X X X X X P81 P80 Power-on U U U U U U 1 1 /RESET and WDT time out U U U U U U 1 1 Wake-up from Sleep, Idle mode U U U U U U P P Bit Name P97 P96 P95 P94 P93 P92 P91 P90 Power-on 1 1 1 1 1 1 1 1 /RESET and WDT time out 1 1 1 1 1 1 1 1 Wake-Up from Sleep, Idle mode P P P P P P P P TC4FF1 TC4FF0 TC4S TC4CK2 TC4CK1 TC4CK0 TC4M1 TC4M0 Power-on 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P Bit Name 0x0C Bit 2 Bit Name Bit Name 0x0B Bit 3 0 TC4D7 TC4D6 TC4D5 TC4D4 TC4D3 TC4D2 TC4D1 TC4D0 Power-on 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P Bit Name X X INT3F INT3R X X WDTIF EXIF0 Power-on U U 0 0 U U 0 0 /RESET and WDT time out U U 0 0 U U 0 0 Wake-up from Sleep, Idle mode U U P P U U P P Bit Name EXIF5 TCIF2 ADIF X EXIF3 TCIF4 SPIF TCIF3 Power-on 0 0 0 U 0 0 0 0 /RESET and WDT time out 0 0 0 U 0 0 0 0 Wake-up from Sleep, Idle mode U P P U P P P P Bit Name X UERRIF RBFF TBEF TBIF EXIF1 X TCIF0 Power-on U 0 0 0 0 0 U 0 /RESET and WDT time out U 0 0 0 0 0 U 0 Wake-up from Sleep, Idle mode U P P P P P U P Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 45 EM78P311N 8-Bit Microcontroller Register Bank 1 Address Name 0x05 TC3CR Reset Type Bit 7 Bit 6 Bit Name TC3CAP TC3S Power-on 0 0 TC3DA 0x08 TC3DB TC2DL 0x0C 0X0D 0X0E 46 • ADCR ADIC ADDH TBKTC 0 X X X U U U 0 0 0 0 U U U P P P U U U TC3DA7 TC3DA6 TC3DA5 TC3DA4 TC3DA3 TC3DA2 TC3DA1 TC3DA0 Power-on 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P 0 TC3DB7 TC3DB6 TC3DB5 TC3DB4 TC3DB3 TC3DB2 TC3DB1 TC3DB0 Power-on 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P ADD1 ADD0 X TC2M TC2S U U U 0 0 0 0 P P U 0 0 0 0 0 P P U P 0 P P P 0 TC2CK2 TC2CK1 TC2CK0 0 TC2D15 TC2D14 TC2D13 TC2D12 TC2D11 TC2D10 TC2D9 TC2D8 Power-On 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P 0 TC2D7 TC2D6 TC2D5 TC2D4 TC2D3 TC2D2 TC2D1 TC2D0 Power-on 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P Bit Name 0x0B 0 Bit 0 P Bit Name 0x0A 0 Bit 1 0 Bit Name TC2CR Power-on / /RESET and WDT time out ADDL Wake-up from Sleep, Idle mode TC2DH TC3CK1 TC3CK0 TC3M Bit 2 P Bit Name 0x09 Bit 3 Wake-up from Sleep, Idle mode Bit Name 0x07 Bit 4 /RESET and WDT time out Bit Name 0x06 Bit 5 ADREF ADRUN ADCK1 ADCK0 0 ADP ADIS2 ADIS1 ADIS0 Power-on 0 0 0 0 1 0 0 0 /RESET and WDT time out 0 0 0 0 1 0 0 0 Wake-up from Sleep, Idle mode P (*) P P P P P P Bit Name ADE7 ADE6 ADE5 ADE4 ADE3 ADE2 ADE1 ADE0 Power-on 0 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P P Bit Name ADD9 ADD8 ADD7 ADD6 ADD5 ADD4 ADD3 ADD2 Power-on U U U U U U U U /RESET and WDT time out P P P P P P P P Wake-up from Sleep, Idle mode P P P P P P P P Bit Name TEN TCK1 TCK0 X Power-on 0 0 0 0 0 0 0 /RESET and WDT time out 0 0 0 0 0 0 0 0 Wake-up from Sleep, Idle mode 0 P P P 0 P P P TBTEN TBTCK2 TBTCK1 TBTCK0 0 Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Register Bank 2 Address Name Reset Type Bit Name 0x05 0x06 URC1 URC2 URS URRD URTD Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 URTD8 UMODE1 UMODE0 BRATE2 BRATE1 BRATE0 UTBE TXE 0 0 0 0 0 0 /RESET and WDT time out P P P P P P 0 0 Wake-up from Sleep, Idle mode P 0 P P P P P 0 Bit Name X X Power-on U U SBIM1 SBIM0 UINVEN 0 0 0 0 X X X U U U /RESET and WDT time out U U P P P U U U Wake-up from Sleep, Idle mode U U P P P U U U URRD8 EVEN PRE PRERR OVERR FMERR URBF RXE Power-on U 0 0 0 0 0 0 /RESET and WDT time out P P P 0 0 0 0 0 Wake-up from Sleep, Idle mode P P P P P P P 0 0 URRD7 URRD6 URRD5 URRD4 URRD3 URRD2 URRD1 URRD0 Power-on U U U U U U U /RESET and WDT time out P P P P P P P P Wake-up from Sleep, Idle mode P P P P P P P P Bit Name 0x09 Bit 5 U Bit Name 0x08 Bit 6 Power-on Bit Name 0x07 Bit 7 U URTD 7 URTD 6 URTD 5 URTD 4 URTD 3 URTD 2 URTD 1 URTD0 Power-on U U U U U U U /RESET and WDT time out P P P P P P P U P Wake-up from Sleep, Idle mode P P P P P P P P Register Bank 3 Address Name 0x05 SPIC1 0x06 SPIC2 0x07 SPID1 0x0A PHC1 0x0B PLC2 0x0C PHC2 0x0D PLC2 Reset Type Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit Name Power-on /RESET and WDT time out Wake-up from Sleep, Idle mode Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 SMP DCOL BRS2 BRS1 BRS0 EDS DORD 0 0 0 0 0 0 0 P P P P P P P P P P P P P P SPIS X X X X SPIM1 SPIM0 0 0 0 0 0 0 0 0 0 0 0 0 P P 0 P P P P P P SPID17 SPID16 SPID15 SPID14 SPID13 SPID12 SPID11 U U U U U U U P P P P P P P P P P P P P P X X /PHE81 /PHE80 /PHE63 /PHE62 /PHE61 U U 1 1 1 1 1 U U 1 1 1 1 1 U U P P P P P X X /PLE81 /PLE80 /PLE63 /PLE62 /PLE61 U U 1 1 1 1 1 U U 1 1 1 1 1 U U P P P P P X X X X /PHE73 /PHE72 /PHE71 U U U U 1 1 1 U U U U 1 1 1 U U U U P P P X X X X /PLE73 /PLE72 /PLE71 U U U U 1 1 1 U U U U 1 1 1 U U U U P P P Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) Bit 0 WBE 0 0 P RBF 0 0 P SPID10 U P P /PHE60 1 1 P /PLE60 1 1 P /PHE70 1 1 P /PLE70 1 1 P • 47 EM78P311N 8-Bit Microcontroller General Purpose Registers Address Name 0x10 R10 ~ ~ 0x3F R3F Reset Type Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit Name - - - - - - - - Power-on U U U U U U U U /RESET and WDT time out P P P P P P P P Wake-up from Sleep, Idle mode P P P P P P P P Legend: “×” = not used “P” = previous value before reset “u” = unknown or don’t care “t” = check Table 7 5.14.4 The Status of RST, T, and P of the Status Register The values of T and P are used to verify the event that triggered the processor to wake up. Table 7 shows the events that may affect the status of T and P. Table 7. The Values of RST, T and P after a reset Reset Type T P Power on 1 1 /RESET during Operation mode *P *P /RESET wake-up during Sleep mode *P *P /RESET wake-up during Idle mode *P *P WDT during Operation mode 0 *P WDT wake-up during Sleep mode 0 *P WDT wake-up during Idle mode 0 *P T P Power on 1 1 WDTC instruction 1 1 WDT time-out 0 *P SLEP instruction 1 0 Wake-Up during Sleep mode *P *P *P: Previous status before reset Table 8 The Events that may affect the T and P Status Event *P: Previous value before reset 48 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller VDD D CLK Oscillator Q CLK CLR Power-on Reset Voltage Detector WDTE WDT Timeout WDT Setup Time RESET /RESET Fig. 5-28 Controller Reset Block Diagram 5.15 Interrupt The EM78P311N has 15 interrupts (9 external, 6 internal) as listed below: Table 9 Interrupt Vector Interrupt Source Enable Condition Int. Flag Int. Vector Priority Internal / External Reset − − 0000 High 0 Internal WDT ENI + WDTEN WDTIF 0003 1 External INT0 ENI + INT0EN=1 EXIEF0 0006 2 Internal TCC ENI + TCIE0=1 TCIF0 0009 3 External INT1 ENI + EXIE1=1 EXIF1 000F 4 Internal TBT ENI + TBIE=1 TBIF 0012 5 Internal UART Transmit ENI + UTIE=1 TBEF 0015 6 Internal Internal UART Receive UART Receive error ENI + URIE=1 ENI+UERRIE=1 TBFF UERRIF 0018 001B 7 8 Internal Internal TC3 SPI ENI + TCIE3=1 ENI + SPIE=1 TCIF3 SPIF 0021 0024 9 10 Internal External TC4 INT3 ENI + TCIE4=1 ENI + EXIE3=1 TCIF4 EXIF3 0027 002A 11 12 Internal Internal AD TC2 ENI + ADIE=1 ENI + TCIE2=1 ADIF TCIF2 0030 0033 13 14 External INT5 ENI + EXIE5=1 EXIF5 0036 Low 15 ISFR0, ISFR1 and ISFR2 are the interrupt status registers that record the interrupt requests in the relative flags/bits. IMR1 and IMR2 are the interrupt mask registers. The global interrupt is enabled by the ENI instruction and is disabled by the DISI instruction. When one of the interrupts (enabled) occurs, the next instruction will be fetched from individual address. The interrupt flag bit must be cleared by instructions before leaving the interrupt service routine and before interrupts are enabled to avoid recursive interrupts. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 49 EM78P311N 8-Bit Microcontroller The flag (except ICIF bit) in the Interrupt Status Register (ISFR 2) is set regardless of the status of its mask bit or the execution of ENI. The RETI instruction ends the interrupt routine and enables the global interrupt (the execution of ENI). 5.16 Oscillator 5.16.1 Oscillator Modes The EM78P311N can operate in two different oscillator modes, i.e., Crystal oscillator mode and External RC oscillator mode (ERC) oscillator mode. User can select which mode by Code Option Register. The maximum limit for operational frequencies of the crystal/resonator under different VDDs is listed below. Table 10 Oscillator Modes Defined by SDCS and OSC Mode Single Clock OSC Oscillator 1 High frequency oscillator 0 ERC Table 11 The Summary of Maximum Operating Speeds Condition High frequency oscillator VDD Max. Fxt. (MHz) 3.0 4.0 5.0 10.0 5.16.2 Crystal Oscillator/Ceramic Resonators (Crystal) EM78P311N has a clock generator. i.e. fc (high frequency) which can be driven by an external clock signal through the OSCI pin. In most applications, Pin OSCI and Pin OSCO can be connected with a crystal or ceramic resonator to generate oscillation. Table 12 provides the recommended values of C1 and C2. Since each resonator has its own attribute, user should refer to its specification for appropriate values of C1 and C2. A serial resistor Rs may be necessary for AT strip cut crystal. 50 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Ext. Clock OSCI OSCO EM78P311N EM78P809N Fig. 5-29 Crystal/Resonator Circuit C1 OSCI XTAL EM78P311N EM78P809N OSCO C2 RS Fig. 5-30 Crystal/Resonator Circuit Table12. Capacitor Selection Guide for Crystal Oscillator or Ceramic Resonator Oscillator Type Frequency Mode Ceramic Resonator HXT Crystal Oscillator HXT Frequency C1 (pF) C2 (pF) 2.0 MHz 20~40 20~40 4.0 MHz 10~30 10~30 1.0 MHz 15~30 15~30 2.0 MHz 15 15 4.0 MHz 15 15 33 0 33 0 C OSCI EM78P311N EM78P809N 740 4 740 4 740 4 XTAL Fig. 5-31 Crystal/Resonator-Series Mode Circuit Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 51 EM78P311N 8-Bit Microcontroller 4.7 K OSCI 740 4 EM78P809N EM78P311N 10 K Vdd 740 4 10 K XTAL C1 C2 Fig. 5-32 Crystal/Resonator-Parallel Mode Circuit 5.16.3 External RC Oscillator Mode For applications that do not need very precise timing calculation, the RC oscillator offers a lot of cost savings. Nevertheless, it should be noted that the frequency of the RC oscillator is influenced by the supply voltage, the values of the resistor (Rext), the capacitor (Cext), and even by the operation temperature. Moreover, the frequency also varies slightly from one chip to another due to the manufacturing process variation. In order to maintain a stable system frequency, the values of the Cext should not be less than 20pF, and the value of Rext should not be greater than 1 MΩ, otherwise, the frequency is easily affected by noise, humidity, and leakage. The smaller the Rext in the RC oscillator, the faster its frequency will be. On the contrary, for very low Rext values, for instance, 1 KΩ, the oscillator becomes unstable because the NMOS cannot correctly discharge the current of the capacitance. Hence, it must be noted that the supply voltage, the operation temperature, the RC oscillator components, the package types, and the PCB layout, will affect the system frequency. Vdd Rext OSCI EM78P311N Cext EM78P809N Fig. 5-33 External RC Oscillator Mode Circuit 52 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Table13. RC Oscillator Frequencies Cext Average Fosc 5V, 25°C Average Fosc 3V, 25°C Rext 20 pF 100 pF 300 pF 3.3k 5.1k 4.32 MHz 2.83 MHz 3.56 MHz 2.8 MHz 1.57 MHz 10k 1.62 MHz 100k 184kHz 187kHz 3.3k 1.39 MHz 1.35 MHz 5.1k 950kHz 930kHz 10k 500kHz 490kHz 100k 54kHz 55kHz 3.3k 580kHz 550kHz 5.1k 390kHz 380kHz 10k 100k 200kHz 21kHz 200kHz 21kHz 1 Note: : Measured based on DIP packages. 2 : The values are for design reference only. 5.17 Code Option Register The EM78P311N has one CODE option word that is not part of the normal program memory. The option bits cannot be accessed during normal program execution. Code Option Register and Customer ID Register arrangement distribution: Word 0 Word 1 Word 2 Bit 12~Bit 0 Bit 12~Bit 0 Bit 12~Bit 0 5.17.1 Code Option Register (Word 0) Word 0 Bit 12 ~ 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CLKS ENWDTB CYES - OSC HLP PR2 PR1 PR0 Bit 12 ~ 9 : Not used Bit 8 (CLKS) : Instruction period option bit CLKS = “0” : two oscillator periods CLKS = “1” : four oscillator periods. Refer to the Instruction Set section. Bit 7 (ENWDTB) : Watchdog timer enable bit ENWDTB = “0” : Enable ENWDTB = “1” : Disable Bit 6 (CYES) : Cycle selection for JMP, CALL instruction CYES = “0” : One cycle CYES = “1” : Two cycles Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 53 EM78P311N 8-Bit Microcontroller Bit 4 (OSC) : Oscillator type selection OSC = “0” : RC type OSC = “1” : Crystal type Bit 3 (HLP) : Power selection HLP = “0” : Low power HLP = “1” : High power Bit 2~0 (PR2~PR0) : Protect Bit PR2~PR0 are write-protect bits, configured as follow s: PR2 PR1 PR0 Protect 1 Disable Others 1 Enable 1 5.17.2 Customer ID Register Word 1 Bit 12~Bit 0 XXXXXXXXXXXXX Word 2 Bit 12~Bit 0 XXXXXXXXXXXXX Bits 12 ~ 0: Customer’s ID code 5.18 Power-on Considerations Any microcontroller is not guaranteed to start and operate properly before the power supply maintains at its steady state. The EM78P311N has a built-in Power On Voltage Detector (POVD) with a detecting level of 2.1V. It will work well if VDD rises fast enough (10 ms or less). In many critical applications, however, additional components are required to provide solutions on probable power-up problems. 5.18.1 External Power-on Reset Circuit The circuit shown in Fig. 5-33 use an external RC to produce the reset pulse. The pulse width (time constant) should be kept long enough for VDD to reach minimum operation voltage. This circuit is used when the power supply has slow rise time. Because the current leakage from the /RESET pin is about ±5μA, it is recommended that R should not be greater than 40K. In this way, the /RESET pin voltage is held below 0.2V. The diode (D) acts as a short circuit at the moment of power down. The capacitor C will discharge rapidly and fully. Rin, the current-limited resistor, will prevent high current or ESD (electrostatic discharge) from flowing to pin /RESET. 54 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Vdd R /RESET D EM78P311N EM78P809N Rin C Fig. 5-34 External Power-Up Reset Circuit 5.18.2 Residue-Voltage Protection When battery is replaced, device power (VDD) is taken off but residue-voltage remains. The residue-voltage may trip below VDD minimum, but not to zero. This condition may cause a poor power-on reset. Fig.35 and Fig.36 show how to build the residue-voltage protection circuit. Vdd Vdd 33K EM78P311N EM78P809N Q1 10K /RESET 40K 1N4684 Fig. 5-35 Residue Voltage Protection Circuit 1 Vdd Vdd R1 EM78P311N EM78P809N Q1 /RESET 40K R2 Fig. 5-36 Residue Voltage Protection Circuit 2 Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 55 EM78P311N 8-Bit Microcontroller 5.19 Instruction Set Each instruction in the instruction set is a 13-bit word divided into an OP code and one or more operands. Normally, all instructions are executed within one single instruction cycle (one instruction consists of 2 oscillator periods), unless the program counter is changed by instruction "MOV R2,A", "ADD R2,A", or by instructions of arithmetic or logic operation on R2 (e.g. "SUB R2,A", "BS(C) R2,6", "CLR R2", ⋅⋅⋅⋅). In this case, the execution takes two instruction cycles. In case the instruction cycle specification is not suitable for certain applications, try to modify the instruction as follows: (A) Change one instruction cycle to consist of 4 oscillator periods. (B) The following commands are executed within two instruction cycles; "JMP", "CALL", "RET", "RETL", "RETI", including the conditional skip ("JBS", "JBC", "JZ", "JZA", "DJZ", "DJZA") instructions. In addition, instructions that are written to the program counter are executed within two instruction cycles. Case (A) is selected by the CODE Option bit, called CLK. One instruction cycle consists of two oscillator clocks if CLK is low, and four oscillator clocks if CLK is high. Note that once the 4 oscillator periods within one instruction cycle is selected as in Case (A), the internal clock source to TCC should be CLK=Fosc/4, not Fosc/2. Furthermore, the instruction set has the following features: (1) Every bit of any register can be set, cleared, or tested directly. (2) The I/O register can be regarded as general register. That is, the same instruction can operate on I/O register. Convention: R = Register designator that specifies which one of the registers (including operation and general purpose registers) is to be utilized by the instruction. b = Bit field designator that selects the value for the bit located in the register R and which affects the operation. k = 8 or 10-bit constant or literal value Binary Instruction 0 0 0 56 • 0000 0000 0000 0000 0000 0000 0000 0001 0010 Hex Mnemonic 0000 0001 0002 NOP DAA CONTW Operation 0 0000 0000 0011 0003 SLEP 0 0 0 0 0 0000 0000 0000 0000 0000 0000 0000 0001 0001 0001 0100 rrrr 0000 0001 0010 0004 000r 0010 0011 0012 WDTC IOW ENI DISI RET 0 0000 0001 0011 0013 RETI 0 0 0000 0000 0001 0100 0001 rrrr 0014 001r CONTR IOR R R No Operation Decimal Adjust A A → CONT 0 → WDT, Stop oscillator 0 → WDT A → IOCR Enable Interrupt Disable Interrupt [Top of Stack] → PC [Top of Stack] → PC, Enable Interrupt CONT → A IOCR → A Status Affected None C None T, P T, P 1 None None None None None None 1 None Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller Binary Instruction Hex Mnemonic Operation 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0000 0000 0000 0001 0001 0001 0001 0010 0010 0010 0010 0011 0011 0011 0011 0100 0100 0100 0100 0101 0101 0101 0101 01rr 1000 11rr 00rr 01rr 10rr 11rr 00rr 01rr 10rr 11rr 00rr 01rr 10rr 11rr 00rr 01rr 10rr 11rr 00rr 01rr 10rr 11rr rrrr 0000 rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr 00rr 0080 00rr 01rr 01rr 01rr 01rr 02rr 02rr 02rr 02rr 03rr 03rr 03rr 03rr 04rr 04rr 04rr 04rr 05rr 05rr 05rr 05rr MOV CLRA CLR SUB SUB DECA DEC OR OR AND AND XOR XOR ADD ADD MOV MOV COMA COM INCA INC DJZA DJZ R A, R, R R A, R, A, R, A, R, A, R, A, R, R R R R R R 0 0110 00rr rrrr 06rr RRCA R 0 0110 01rr rrrr 06rr RRC R 0 0110 10rr rrrr 06rr RLCA R 0 0110 11rr rrrr 06rr RLC R 0 0111 00rr rrrr 07rr SWAPA R 0 0 0 0 0 0 0 0111 0111 0111 100b 101b 110b 111b 01rr 10rr 11rr bbrr bbrr bbrr bbrr rrrr rrrr rrrr rrrr rrrr rrrr rrrr 07rr 07rr 07rr 0xxx 0xxx 0xxx 0xxx SWAP JZA JZ BC BS JBC JBS R R R R, R, R, R, 1 00kk kkkk kkkk 1kkk CALL k 1 1 1 1 1 01kk 1000 1001 1010 1011 kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk 1kkk 18kk 19kk 1Akk 1Bkk JMP MOV OR AND XOR k A, A, A, A, 1 1100 kkkk kkkk 1Ckk RETL k 1 1 1 1 1101 1111 1110 1110 kkkk kkkk 1000 1001 1Dkk 1Fkk 1E8k 1E9k SUB ADD PAGE BANK A, k A, k k k kkkk kkkk kkkk kkkk R, A R A R A R A R A R A R R b b b b k k k k A→R 0→A 0→R R-A → A R-A → R R-1 → A R-1 → R A∨R→A A∨R→R A&R→A A&R→R A⊕R→A A⊕R→R A+R→A A+R→R R→A R→R /R → A /R → R R+1 → A R+1 → R R-1 → A, skip if zero R-1 → R, skip if zero R(n) → A(n-1), R(0) → C, C → A(7) R(n) → R(n-1), R(0) → C, C → R(7) R(n) → A(n+1), R(7) → C, C → A(0) R(n) → R(n+1), R(7) → (C), C → (R(0) R(0-3) → ( A(4-7), R(4-7) → ( A(0-3) R(0-3) → ( R(4-7) R+1 → A, skip if zero R+1 → R, skip if zero 0→ ( R(b) 1→ ( R(b) if R(b)=0, skip if R(b)=1, skip PC+1 → [SP], (Page, k) → (PC) (Page, k) → (PC) k→A Avk→A A&k→A A⊕k→A k → A, [Top of Stack] → PC k-A → A k+A → A K->R5(6:4) K->R4(7:6) Status Affected None Z Z Z,C,DC Z,C,DC Z Z Z Z Z Z Z Z Z,C,DC Z,C,DC Z Z Z Z Z Z None None C C C C None None None None None None None None None None None Z Z Z None Z,C,DC Z,C,DC None None 1 Note: This instruction is applicable to IOC6~IOCA, IMR1, IMR2 only. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 57 EM78P311N 8-Bit Microcontroller 6 Absolute Maximum Ratings 6.1 Absolute Maximum Ratings Items Rating Temperature under bias -40°C to 85°C Storage temperature -65°C to 150°C Input voltage -0.3V to +6.0V Output voltage -0.3V to +6.0V Operating Frequency (2clk) DC to 10MHz 6.2 Recommended Operating Conditions Vss = 0V Symbol Parameter VDD Supply Voltage Fc 58 • Crystal: VDD 4.5 to 5.5V Crystal: VDD 2.5 to 5.5V Condition Min. Typ. Fc = 10MHz 4.0 − Fc = 4MHz 2.5 − 1 − 10 1 − 4 Two cycles with two clocks Max. Unit 5.5 V MHz Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 7 Electrical Characteristics 7.1 DC Electrical Characteristics Ta= 25 °C, VDD= 5.0V ± 5%, VSS= 0V Symbol Parameter Fc ERC Crystal: 4.5V to VDD ERC: VDD = 5V Input High Threshold Voltage (Schmitt Trigger ) Sink current Input Low Threshold Voltage (Schmitt Trigger ) Sink current Input Leakage Current for input pins Input High Voltage (Schmitt Trigger) Input Low Voltage (Schmitt Trigger) Input High Threshold Voltage (Schmitt Trigger) Input Low Threshold Voltage (Schmitt Trigger) Clock Input High Voltage Clock Input Low Voltage Output High Voltage (Ports 6, 7, 8, 9) Output Low Voltage (Port 9) Output Low Voltage (Ports 6, Port 7, Port 8) Pull-high current Pull-Low current Sleep mode Power down current Sleep mode Power down current Idle mode Operating supply current at two clocks Normal mode Operating supply current at two clocks VIHRC IRC1 VILRC IRC2 IIL VIH1 VIL1 VIHT1 VILT1 VIHX1 VILX1 IOH1 IOL1 IOL2 IPH IPL ISB1 ISB2 ICC3 ICC4 Condition Min. Typ. Max. Unit Two cycles with two clocks R: 5.1KΩ, C: 100 pF 1 630 − 900 10 1170 MHz kHz OSCI in RC mode 2.8 4 4.5 V VI from low to high , VI=5V 15.5 22 28.5 mA OSCI in RC mode 1.3 1.8 2.7 V VI from high to low , VI=2V 12 17 22 mA VIN = VDD, VSS -1 0 1 μA Ports 6, 7, 8, 9 0.7VDD − VDD +0.3V V Ports 6, 7, 8, 9, -0.3V − 0.3 VDD V /RESET, TCC, INT 0.7 VDD − VDD +0.3V V /RESET, TCC, INT -0.3V − 0.3 VDD V 0.7VDD -0.3V − − VDD+0.3V 0.3VDD V V VOH = VDD-0.4V -3.5 -5 -6.5 mA VOL = VSS+0.4V 3 5 7 mA VOL = VSS+0.4V 12 15 20 mA Pull-high active, input pin at VSS Pull-high active, input pin at VDD WDT All input and I/O disabled pins at VDD, WDT output pin floating enabled -50 50 -75 75 -100 100 μA uA 0.8 1.5 μA 6 10 μA 1.1 1.5 mA 3.0 3.5 mA OSCI in crystal mode OSCI in crystal mode VDD=5V, /RESET= 'High', Fc=8MHz, CLKS="0", output pin floating, WDT enabled Note: * Data in the Minimum, Typical, Maximum (“Min”, “Typ”, ”Max”) columns are based on characterization results at 25°C. Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 59 EM78P311N 8-Bit Microcontroller Ta= 25 °C, VDD= 3.0V ± 5%, VSS= 0V Symbol Parameter Condition Min. Typ. Max. Unit Fc ERC Crystal: 2.5V to VDD ERC: VDD = 3V Input High Threshold Voltage (Schmitt Trigger) Sink current Input Low Threshold Voltage (Schmitt Trigger) Sink current Input Leakage Current for input pins Input High Voltage (Schmitt Trigger) Input Low Voltage (Schmitt Trigger) Input High Threshold Voltage (Schmitt Trigger) Input Low Threshold Voltage (Schmitt Trigger) Clock Input High Voltage Clock Input Low Voltage Output High Voltage (Ports 6, 7, 8, 9) Output Low Voltage (Ports9) Output Low Voltage (Ports 6,Port7, Port8) Pull-high current Pull-low current Sleep mode Power down current Sleep mode Power down current Idle mode Operating supply current at two clocks Normal mode Operating supply current at two clocks Two cyclea with two clocks R: 5.1KΩ, C: 100 pF 1 600 850 4 1100 MHz kHz OSCI in RC mode 1.6 2.3 2.8 V VI from low to high , VI=5V 7 9.5 12 uA OSCI in RC mode 0.7 1 1.3 V VI from high to low , VI=2V 6 8.5 11 uA VIN = VDD, VSS -1 0 1 μA Ports 6,7,8,9,A 0.7VDD VDD+0.3V V Ports 6,7,8,9,A -0.3V 0.3VDD V /RESET, TCC 0.7 VDD VDD +0.3V V /RESET, TCC -0.3V 0.3 VDD V LOSCI,OSCI in crystal mode LOSCI,OSCI in crystal mode 0.7 VDD -0.3V VDD +0.3V 0.3 VDD V V VOH = VDD-0.4V -2 -3.5 -5 mA VOL = VSS+0.4V 2 3.5 5 mA VOL = VSS+0.4V 10 13 16 mA Pull-high active, input pin at VSS Pull-low active, input pin at VDD -15 15 -23 23 -31 30 uA uA All input and I/O WDT disabled pins at VDD, output pin floating WDT enabled − 0.4 0.8 μA − 1.5 3 μA − 0.3 0.5 mA − 1.1 1.5 mA VIHRC IRC1 VILRC IRC2 IIL VIH1 VIL1 VIHT2 VILT2 VIHX1 VILX1 IOH1 IOL1 IOL2 IPH IPL ISB1 ISB2 ICC3 ICC4 VDD=3V, /RESET= 'High', Fc=4MHz, CLKS="0", output pin floating, WDT enabled * The typical value is based on characterization results at 25°C 60 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller A/D Converter Characteristic (Vdd =2.5V to 5.5V, Vss=0V, Ta = -40 to 85°C) Symbol VAREF VASS VAI IAI1 IAI2 IVDD Ivref IVDD IVref Parameter Condition Analog reference voltage VAREF - VASS≧2.5V − Analog input voltage Analog supply current Analog supply current Min. Typ. Max. Unit 2.5 − VDD V Vss − Vss V VASS − VAREF V VDD =VAREF=5.0V, VASS =0.0V 750 850 1000 uA (V reference from VDD) -10 0 +10 uA VDD =VAREF=5.0V, VASS =0.0V 500 600 820 uA (V reference from VREF) 200 250 300 uA RN Resolution VDD =VAREF=5.0V, VASS =0.0V 9 10 − Bits LN Linearity error VDD = 2.5 to 5.5V Ta=25°C 0 ±1 ±2 LSB DNL Differential nonlinear error VDD = 2.5 to 5.5V Ta=25°C 0 ±0.5 ±0.9 LSB FSE Full scale error VDD =VAREF=5.0V, VASS =0.0V ±0 ±1 ±2 LSB OE Offset error VDD =VAREF=5.0V, VASS =0.0V ±0 ±0.5 ±1 LSB ZAI Recommended impedance of analog voltage source 0 8 10 KΩ TAD A/D clock period VDD =VAREF=5.0V, VASS =0.0V 4 − − us TCN A/D conversion time VDD =VAREF=5.0V, VASS =0.0V 14 − 14 TAD ADIV A/D input voltage range VDD =VAREF=5.0V, VASS =0.0V 0 − VAREF V ADOV A/D output voltage swing VDD =VAREF=5.0V, VASS =0.0V, RL=10KΩ 0 0.2 0.3 4.7 4.8 5 PSR Power Supply Rejection VDD =5.0V±0.5V ±0 − Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) ±2 V LSB • 61 EM78P311N 8-Bit Microcontroller 7.2 AC Electrical Characteristic Ta=- 40°C ~ 85 °C, VDD=5V ± 5%, VSS=0V Symbol Parameter Conditions Min Dclk Input CLK duty cycle − 45 Tins Instruction cycle time Crystal type (high frequency) (CLKS="0") RC type Ttcc TCC input period Tdrh Device reset hold time Ta = 25°C 11.3 Trst /RESET pulse width Ta = 25°C 2000 Twdt Watchdog timer period Ta = 25°C 11.3 Tset Input pin setup time − − Thold Input pin hold time Output pin delay time Cload=20pF SDI data setup time Setup time of SDI data input to SCK↑or SCK↓ 55 % 200 DC ns DC ns − ns − Tdelay Tstup1 50 500 (Tins+20)/ N* − Typ Max Unit − 16.2 21.6 − − 16.2 21.6 0 − ms ns ms ns − 20 − ns − − 50 25 − 50 ns ns − 25 50 ns − 25 50 ns Slave mode (Fmain=8 MHz) 200 − − ns Slave mode (Fmain=8 MHz) 200 − − ns 400 − − ns − 25 50 ns Thold1 SDI data hold time Tvalid1 SDO output valid time SCK↑or SCK↓to SDO data output Hold time of SDI data input to SCK↓or SCK↑ Tsckh SCK input high time Tsckl SCK input low time Tsetup2 Slave mode setup /SS↓ to SCK↑or SCK↓(Fmain=8 MHz) time Tdelay1 Slave mode unselect /SS↑ to SDO output hi-impedance delay time delay time * N= selected prescaler ratio 62 • Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) EM78P311N 8-Bit Microcontroller 7.3 Timing Diagram AC Test Input/Output W aveform 2.4 2.0 0.8 TEST POINTS 2.0 0.8 0.4 AC Testing : Input is driven at 2.4V for logic "1",and 0.4V for logic "0".Tim ing m easurem ents are m ade at 2.0V for logic "1",and 0.8V for logic "0". RESET Tim ing (CLK="0") NOP Instruction 1 Executed CLK /RESET Tdrh TCC Input Tim ing (CLKS="0") Tins CLK TCC Ttcc Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice) • 63 EM78P311N 8-Bit Microcontroller APPENDIX A Package Types: OTP MCU Package Type Pin Count Package Size EM78P311NP DIP 28 600 mil EM78P311NK SDIP 28 400 mil EM78P311NAK SDIP 28 300 mil EM78P311NM SOP 28 300 mil EM78P311NS SSOP 28 209 mil Y/S/J：Green product does not contain hazardous substances. The third edition of Sony SS-00259 standard. Pb content should be less than 100ppm. Pb content to fit in with Sony spec. Part No. EM78P311SxS/xJ Electroplate type Sn/Cu Pure Tin Ingredient (%) Cu:1.0~3.0% Sn :100% Melting point(°C) ~227°C 232°C 13 11.4 Hardness (hv) 10~12 8~10 Elongation (%) 40% >50% Electrical resistivity (μΩ-cm) 64 • EM78P311SxY Product Specification (V1.0) 10.02.2006 (This specification is subject to change without further notice)