EUP8010X Linear Li-Ion/Polymer Charger IC with Integrated FET and Charger Timer DESCRIPTION FEATURES The EUP8010X series are highly integrated single cell Li-Ion/Polymer battery charger IC designed for handheld devices. The EUP8010X integrates internal power FET, current sensor, charge status and reverse current protection in a single monolithic devices.When AC-adapter is applied, an external resistor sets the magnitude of the charge current, which may be programmed up to 1A. The EUP8010X charges the battery in three phases: conditioning, constant current, and constant voltage. Charge is terminated based on minimum current. An internal charge timer provides a backup safety for charge termination. The EUP8010X automatically re-starts the charge if the battery voltage falls below an internal threshold. The EUP8010X also automatically enters sleep mode when DC supplies are removed. No external sense resistor or blocking diode is required for charging. z z z z z z z z z Integrated Power FET and Current Sensor for Up to 1A Charge Applications Charge Termination by Minimum Current and Time Precharge Conditioning With Safety Timer Reverse Leakage Protection Prevents Battery Drainage Status Outputs for LED or System Interface Indicates Charge and Fault Conditions Optional Battery Temperature Monitoring Before and During Charge Automatic Sleep Mode for Low-Power Consumption Available in 3mm × 3mm TDFN-10 Package RoHS Compliant and 100% Lead (Pb)-Free APPLICATIONS z z z z Smartphones Digital Cameras PDAs/ MP3 Players Stand-Alone Chargers Typical Application Circuit Figure 1. EUP8010B DS8010X Ver 1.2 June 2007 1 EUP8010X Block Diagram Figure 2. DS8010X Ver 1.2 June 2007 2 EUP8010X Pin Configurations Package Type Pin Configurations Package Type EUP8010A TDFN-10 EUP8010B TDFN-10 EUP8010C TDFN-10 EUP8010D TDFN-10 Pin Configurations Pin Description PIN A B C D I/O AC 1 1 1 1 I Charge input voltage. This input must be tied to the VCC pin. VCC 2 2 2 2 I VCC supply input STAT1 3 3 3 3 O Charge status output 1 (open collector) STAT2 4 4 4 4 O Charge status output 2 (open collector) VSS 5 5 5 5 - Ground input ISET 6 6 6 6 O Charge current set point PG 7 7 - - O Power good status output (open collector) TS 8 - - 8 I Temperature sense input CE - 8 7 7 I Charge enable input (active low) TTE BAT - - 8 - I Timer and termination enable input (active low) 9 9 9 9 I Battery voltage sense input OUT 10 10 10 10 O Charge current output DS8010X Ver 1.2 June 2007 DESCRIPTION 3 EUP8010X Ordering Information Order Number Package Type EUP8010A-JIR1 TDFN-10 EUP8010B-JIR1 TDFN-10 EUP8010C-JIR1 TDFN-10 EUP8010D-JIR1 TDFN-10 Marking xxxxx 8010A xxxxx 8010B xxxxx 8010C xxxxx 8010D EUP8010X- □ □ □ □ Lead Free Code 1: Lead Free 0: Lead Packing R: Tape& Reel Operating temperature range I: Industry Standard Package Type J: TDFN-10 DS8010X Ver 1.2 June 2007 4 Operating Temperature range -20 °C to 70°C -20 °C to 70°C -20 °C to 70°C -20 °C to 70°C EUP8010X Absolute Maximum Ratings Input voltage(AC,VCC, CE , ISET,OUT,BAT, PG ,STAT1,STAT2, TS, TTE ) -------------------- 0.3V to 6V Output sink / source current (STAT1,STAT2, PG ) ---------------------------------------------------- 15mA Output current (TS ) --------------------------------------------------------------------------------------- 200μA Output current (OUT) ------------------------------------------------------------------------------------- 1.5 A Junction temperature range, TJ ------------------------------------------------------------------------- 150°C Storage temperature range, Tstg ------------------------------------------------------------- -65°C to 150°C Lead temperature (soldering, 10s) -------------------------------------------------------------------260°C Dissipation Ratings Package θJA TDFN-10 48°C/W Derating Factor Above TA =25°C 0.0208 W/°C TA < 40°C Power Rating 1.5W Recommended Operating Conditions (1) Min. Max. Unit Supply voltage (from AC input), VCC 4.5 5.5 V Operating junction temperature range, TJ -40 125 °C Electrical Characteristics over Recommended Operating Free-Air Temperature Range Parameter Conditions EUP8010X Unit Min. Typ. Max. Input Current VCC current, ICC(VCC) Sleep current, ICC(SLP) Standby current, ICC(STBY) VCC > VCC(min) Sum of currents into OUT pin, VCC < V(SLP) CE = High, 0°C ≤ TJ ≤ 85°C 0.9 1.5 mA 1 5 µA 50 150 Voltage Regulation Output voltage, VO(REG) Voltage regulation accuracy AC dropout voltage (V(AC)-V(OUT)), V(DO) Current Regulation AC output current range, IO(OUT) (1) Output current set voltage, V(SET) Output current set factor, K(SET) DS8010X Ver 1.2 June 2007 V 4.2 TA = 25°C -0.5% 0.5% -1.5% 1.5% VO(OUT) = VO(REG), IO(OUT) = 1A VI(BAT) >V(LOWV), VCC ≥ 4.5 V Voltage on ISET pin, VCC ≥ 4.5 V, VI(BAT) > V(LOWV), 50 mA ≤ IO(OUT) ≤ 1 A 400 50 500 mV 1000 mA V 2.410 2.460 2.510 304 320 336 10 mA ≤ IO(OUT) < 50 mA 294 320 346 1 mA ≤ IO(OUT) < 10 mA 246 320 416 5 EUP8010X Electrical Characteristics Over Recommended Operating Free-Air Temperature Range Parameter Conditions Precharge and Short-Circuit Current Regulation Precharge to fast-charge transition Voltage on OUT pin threshold, V(LOWV) Deglitch time for fast-charge to precharge transition Precharge range, IO(PRECHG) (2) 0 V < VI(BAT) < V(LOWV) Voltage on ISET pin, Precharge set voltage, V(PRECHG) 0 V < VI(BAT) > V(LOWV) Charge Taper and Termination Detection Charge taper detection range, VI(BAT) > V(RCH) I(TAPER) (3) Voltage on ISET pin, VO(REG) = 4.2V, Charge taper detection set voltage, V(TAPER) VI(BAT) > V(RCH) Voltage on ISET pin, VO(REG) = 4.2V, Charge termination detection set voltage, V(TERM) (4) VI(BAT) > V(RCH) Deglitch time for TAPER detection, tTPRDET Deglitch time for termination detection, tTRMDET Temperature Sense Comparator EUP8010X Unit Min. Typ. Max. 2.8 3.0 3.2 V 250 375 500 ms 100 mA 260 mV 100 mA 5 230 245 5 235 250 265 11 18 25 250 375 500 mV ms 250 375 500 Low-voltage threshold, V(LTF) 2.49 2.515 2.54 High-voltage threshold, V(HTF) 0.495 0.510 0.525 102 112 122 µA 250 375 500 ms Current source, I(TS) Deglitch time for temperature fault, t(DEGL) Battery Recharge Threshold VO(REG) VO(REG) VO(REG) -0.10 -0.050 -0.150 Recharge threshold, VRCH Deglitch time for recharge detect, t(DEGL) STAT1, STAT2, and PG Outputs Low-level output saturation voltage, IO = 5 mA VOL K (SET) × V(SET) (1) I O(OUT) = R SET 250 K (SET) × V(TERM) (4) I O(TERM) = R SET 6 V 500 ms 0.25 V K (SET) × V(PRECHG) (2) I O(PRECHG) = R SET × V(TAPER ) K (3) I O(TAPER ) = (SET) R SET DS8010X Ver 1.2 June 2007 375 V EUP8010X Parameter Conditions EUP8010X Unit Min. Typ. Max. Charge Enable ( CE ), Timer and Termination Enable ( TTE ) Inputs Low-level input voltage, VIL IIL = 10 µA 0 High-level input voltage, VIH IIL = 20 µA 1.4 CE or TTE low-level input current, IIL 0.4 -1 CE or TTE high-level input current, IIH 1 V µA Timers Precharge time, t(PRECHG) 1,650 1,940 2,230 2,230 Taper time, t(TAPER) 8010A,8010B,8010C,8010D 1,650 1,940 Charge time, t(CHG) 8010A,8010B,8010C,8010D 16,500 19,400 22,300 Timer fault recovery current, I(FAULT) Sleep Comparator Sleep-mode entry threshold voltage, V(SLP) Sleep mode exit threshold voltage, V(SLPEXIT) Sleep mode deglitch time 200 2.3 V ≤ VI(BAT) ≤ VO(REG) 2.3 V ≤ VI(BAT) ≤ VO(REG) s µA VCC ≤ VI(BAT) +100 mV VCC ≥ VI(BAT) +190mV 250 375 500 V ms Thermal Shutdown Thresholds Thermal trip threshold, T(SHTDWN) 165 Thermal hysteresis 30 °C Undervoltage Lockout Undervoltage lockout V(UVLO) Decreasing VCC 2.2 Hysteresis DS8010X Ver 1.2 June 2007 2.4 20 7 2.6 V mV EUP8010X Application Information Figure 3. Operational Flow Chart DS8010X Ver 1.2 June 2007 8 EUP8010X Functional Description Temperature Qualification ( 8010A,8010D Only) The EUP8010X continuously monitors battery temperature by measuring the voltage between the TS and VSS pins. An internal current source provides the bias for most common 10-kΩ negative-temperature coefficient thermistors (NTC) (see Figure 4). The device compares the voltage on the TS pin against the internal V(LTF) and V(HTF) thresholds to determine if charging is allowed. Once a temperature outside the V(LTF) and V(HTF) thresholds is detected the device immediately suspend the charge. The device suspend charge by turning off the power FET and holding the timer value (i.e. timers are NOT reset). Charge is resumed when the temperature returns to the normal range. However the user may modify these thresholds by adding two external resistors. See Figure 5. Battery Pre-Conditioning During a charge cycle if the battery voltage is below the V(LOWV) threshold, the EUP8010X applies a precharge current, IO(PRECHG), to the battery. This feature revives deeply discharged cells. The resistor connected between the ISET and VSS, RSET, determines the precharge rate. The V(PRECHG) and K(SET) parameters are specified in the specifications table. I O(PRECHG) = V(PRECGH ) × K (SET ) R SET ------------ (1) The EUP8010X activates a safety timer, t(PRECHG), during the conditioning phase. If V(LOWV) threshold is not reached within the timer period, the EUP8010X turns off the charger and enunciates FAULT on the STATx pins. Please refer to the Timer Fault Recovery section for additional details. Figure 4. Temperature Sensing Configuration DS8010X Ver 1.2 June 2007 9 Figure 5. Temperature Sensing Thresholds Battery Charge Current The EUP8010X offers on-chip current regulation with programmable set point. The resistor connected between the ISET and VSS, RSET, determines the AC charge rate. The V(SET) and K(SET) parameters are specified in the specifications table. I O(OUT) = V(SET ) × K (SET ) R SET ---------------------- (2) Battery Voltage Regulation The voltage regulation feedback is through the OUT pin. This input is tied directly to the positive side of the battery pack. The EUP8010X monitors the battery pack voltage between the OUT and VSS pins. When the battery voltage rises to VO(REG) threshold, the voltage regulation phase begins and the charging current begins to taper down. As a safety backup, the EUP8010X also monitors the charge time in the charge mode. If charge is not terminated within this time period, t(CHG), the EUP8010X turns off the charger and enunciates FAULT on the STATx pins. Please refer to the Timer Fault Recovery section for additional details. EUP8010X Charge Taper Detection, Termination and Recharge The EUP8010X monitors the charging current during the voltage regulation phase. Once the taper threshold, I(TAPER),is detected the EUP8010X initiates the taper timer, t(TAPER). Charge is terminated after the timer expires. The resistor connected between the ISET and VSS, RSET, determines the taper detection level. The V(TAPER) and K(SET) parameters are specified in the specifications table. V(TAPER ) × K (SET ) I (TAPER) = R SET ------------------ (3) The EUP8010X resets the taper timer in the event that the charge current returns above the taper threshold, I(TAPER). In addition to the taper current detection, the EUP8010X terminates charge in the event that the charge current falls below the I(TERM) threshold. This feature allows for quick recognition of a battery removal condition or insertion of a fully charged battery. Note that charge timer and taper timer are bypassed for this feature. The resistor connected between the ISET and VSS, RSET, determines the taper detection level. The V(TERM) and K(SET) parameters are specified in the specifications table. I (TERM) = V(TERM ) × K (SET ) R SET Charge Status Outputs The open-drain STAT1 and STAT2 outputs indicate various charger operations as shown in the following table. These status pins can be used to drive LEDs or communicate to the host processor. Note that OFF indicates the open-drain transistor is turned off. Table 1. Status Pins Summary CHARGE STATE Precharge in progress Fast charge in progress Charge done Charge suspend (temperature) Timer fault Sleep mode STAT1 STAT2 ON ON ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF means the open-drain output transistor on the STAT1 and STAT2 pins is in an off state. PG Output The open-drain PG (Power Good) indicates when the AC adapter is present. The output turns ON when a valid voltage is detected. This output is turned off in the sleep mode. The PG pin can be used to drive an LED or communicate to the host processor. -------------------- (4) CE Input (Charge Enable) After charge termination, the EUP8010X re-starts the charge once the voltage on the OUT pin falls below the V(RCH) threshold. This feature keeps the battery at full capacity at all times. The CE digital input is used to disable or enable the charge process. A low-level signal on this pin enables the charge and a high-level signal disables the charge and places the device in a low-power mode. A high-to-low transition on this pin also resets all timers and timer fault conditions. Sleep Mode The EUP8010X enters the low-power sleep mode if AC-adapter is removed from the circuit. This feature prevents draining the battery during the absence of input supply. TTE Input (Timer and Termination Enable) The TTE digital input is used to disable or enable the fast-charge timer and charge taper detection. A low-level signal on this pin enables the fast-charge timer and taper timer and a high-level signal disables this feature. Thermal shutdown and Protection The EUP8010X monitors the junction temperature, TJ, of the die and suspends charging if TJ exceeds T(SHTDWN). Charging resumes when TJ falls below T(SHTDWN) by approximately 30 ℃. DS8010X Ver 1.2 June 2007 10 EUP8010X Timer Fault Recovery As shown in Figure 3, EUP8010X provides a recovery method to deal with timer fault conditions. The following summarizes this method: Condition #1: Charge voltage above recharge threshold (V(RCH)) and timeout fault occurs Recovery method: EUP8010X waits for the battery voltage to fall below the recharge threshold. This could happen as a result of a load on the battery, self-discharge or battery removal. Once the battery falls below the recharge threshold, the EUP8010X clears the fault and starts a new charge cycle. A POR or CE or TTE toggle also clears the fault. Condition #2: Charge voltage below recharge threshold (V(RCH)) and timeout fault occurs Recovery method: Under this scenario, the EUP8010X applies the I(FAULT) current. This small current is used to detect a battery removal condition and remains on as long as the battery voltage stays below the recharge threshold. If the battery voltage goes above the recharge threshold, then the EUP8010X disables the I(FAULT) current and executes the recovery method described for condition #1. Once the battery falls below the recharge threshold, the EUP8010X clears the fault and starts a new charge cycle. A POR or CE or TTE toggle also clears the fault. DS8010X Ver 1.2 June 2007 11 EUP8010X Packaging Information TDFN-10 SYMBOLS MILLIMETERS MIN. MAX. MIN. MAX. A 0.70 0.80 0.028 0.031 A1 0.00 0.05 0.000 0.002 D 2.90 3.10 0.114 0.122 E1 DS8010X Ver 1.2 June 2007 INCHES 1.70 0.067 E 2.90 3.10 0.114 0.122 L 0.30 0.50 0.012 0.020 b 0.18 0.30 0.007 0.012 e 0.50 0.020 D1 2.40 0.094 12