EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 1206 Package Chip LED with Inner lens 11-21/BHC-AP2R1/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint version. Descriptions ․The 11-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 11-21/BHC-AP2R1/2T Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 Chip Material Emitted Color InGaN Blue http://www.everlight.com Prepared date: 17-Aug-2005 Lens Color Water Clear Rev. 2 Page: 1 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Package Outline Dimensions - + Notes: The tolerances unless mentioned are ±0.1, unit=mm. Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 2 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ ESD 150 V Pd 110 mW IFP 100 mA Electrostatic Discharge(HBM) Power Dissipation Peak Forward Current (Duty 1/10 @1KHz) Soldering Temperature Reflow Soldering : 260 ℃ for 10 sec. Tsol Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 57 ----- 140 mcd Viewing Angle 2θ1/2 ----- 60 ----- deg Peak Wavelength Dominant Wavelength λp ----- 468 ----- nm λd 464.5 ----- 476.5 nm Spectrum Radiation Bandwidth △λ ----- 35 ----- nm Forward Voltage VF 2.7 3.3 3.7 V Reverse Current IR ----- ----- 50 μA Condition IF =20mA VR =5V Notes: 1.Tolerance of Luminous Intensity: ±10% 2.Tolerance of Dominant Wavelength: ±1nm Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 3 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Bin Range Of Dom. Wavelength Group A Bin Min Max A9 464.5 467.5 A10 467.5 470.5 A11 470.5 473.5 A12 473.5 476.5 Unit Condition nm IF =20mA Bin Range Of Luminous Intensity Bin Min Max P2 57 72 Q1 72 90 Q2 90 112 R1 112 140 Unit Condition mcd IF =20mA Notes: 1.Tolerance of Luminous Intensity: ±10% 2.Tolerance of Dominant Wavelength: ±1nm Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 4 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 5 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Label explanation xxxxxx xxxxxx CAT: Luminous Intensity Rank RoHS HUE: Dom. Wavelength Rank xxxxxxxxxxxx xxxx REF: Forward Voltage Rank xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned are ±0.1, Unit = mm. Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 6 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned are ±0.1, Unit = mm. Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Desiccant Rev. 2 Label Page: 7 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample No. Items Test Condition Hours/Cycles Size Temp. : 260℃±5℃ 1 Reflow Soldering 22 PCS. 6 Min. Min. 5sec. 2 3 4 5 Ac/Re 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 High Temperature Storage Low Temperature Storage 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 8 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year.(To fit the MSL-2 .) 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 9 of 10 Prepared by: Meng Yali EVERLIGHT ELECTRONICS CO.,LTD. 11-21/BHC-AP2R1/2T 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No:SZDSE-111-B03 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date: 17-Aug-2005 Rev. 2 Page: 10 of 10 Prepared by: Meng Yali