EVERLIGHT 11-21SURC/S530

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
1206 Package Chip LEDs with Inner Lens
11-21SURC/S530-XX/TR8
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS complaint version.
Descriptions
․The 11-21 SMD Taping is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Part No.
11-21SURC/S530-XX/TR8
Chip
Material
Emitted Color
AlGaInP
Hyper Red
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Lens Color
Water Clear
Page: 1 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
Package Outline Dimensions
-
+
Note: Tolerances Unless Dimension ±0.1mm , Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 2 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
25
mA
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40~ +90
℃
ESD
2000
V
Pd
60
mW
IF
60
mA
Electrostatic Discharge(HBM)
Power Dissipation
Peak Forward Current
(Duty 1/10 @1KHz)
Soldering Temperature
Tsol
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Luminous Intensity
Iv
*Chip
Rank
Min.
Typ.
Max.
A2
29
71
-----
A3
68
102
-----
A4
93
138
-----
A5
112
172
-----
A6
135
208
-----
Unit Condition
mcd
Viewing Angle
2θ1/2
-----
-----
60
-----
deg
Peak Wavelength
Dominant Wavelength
λp
-----
-----
632
-----
nm
λd
-----
-----
624
-----
nm
Spectrum Radiation
Bandwidth
△λ
-----
-----
20
-----
nm
Forward Voltage
VF
-----
1.7
2.0
2.4
V
Reverse Current
IR
-----
-----
-----
10
μA
*11-21SURC/S530-XX/TR8
Chip Rank
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 3 of 9
Prepared by: Meng Yali
IF=20mA
VR=5V
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 4 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
■ Label explanation
CAT: Luminous Intensity
xxxxxx
xxxxxx
HUE: Dom. Wavelength
RoHS
xxxxxxxxxxxx
xxxx
REF: Forward Voltage
xxxxxxxx
■ Reel Dimensions
Note: Tolerances Unless Dimension ±0.1mm , Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 5 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
■ Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: Tolerances Unless Dimension ±0.1mm , Unit = mm
■ Moisture Resistant Packaging
Label
Aluminum moistue-proof bag
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Desiccant
Rev 1
Label
Page: 6 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level : 90 %
LTPD : 10 %
Test
Sample
No.
Items
Test Condition
Ac/Re
Hours/Cycles Size
Temp. : 260℃±5℃
1
Reflow
22 Pcs.
0/1
6 Sec.
Min. 5 sec.
2
3
4
5
Temperature Cycle
H : +100℃ 15 min.
∫ 5 min.
L : -40℃ 15 min.
300 Cycles
22 Pcs.
0/1
Thermal Shock
H : +100℃ 5 min.
∫ 10 sec.
L : -10℃ 5 min.
300 Cycles
22 Pcs.
0/1
Temp. : 100℃
1000 Hrs.
22 Pcs.
0/1
Temp. : -55℃
1000 Hrs.
22 Pcs.
0/1
High Temperature
Storage
Low Temperature
Storage
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 Pcs.
0/1
7
High Temperature /
High Humidity
85℃/RH 85%
1000 Hrs.
22 Pcs.
0/1
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 7 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 8 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SURC/S530-XX/TR8
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:SZDSE-111-008
Prepared date: 17-Aug-2005
Rev 1
Page: 9 of 9
Prepared by: Meng Yali