Features Description The GM7630 is a multi-output positive voltage regulator, designed to provide fixed precision output voltages of 5.1V, 8V at current up to 0.5A and 12V at current up to 1A with external PNP transistor. An internal reset circuit generates a reset pulse when the output 1 decrease below the regulated value. Output2 & 3 can be disabled by TTL input. Protection features include over voltage protection, short circuit protection, and thermal shutdown. Output Currents up to 0.5A (output1 & 2) Output Current up to 1A with External Transistor (output3) Fixed Precision Output 1 voltage 5.1V ± 2% Fixed Precision Output 2 voltage 8V ± 2% Control Signal Generator for Output 3 voltage (12V ± 2%) Reset Facility for Output Voltage1 Output 2,3 with Disable by TTL Input Current Limit Protection at Each Output Thermal Shut Down TYPICAL APPLICATION GM7630 1 2 3 6 7 8 Contorl 9 10 Output3 Cd VIN 1 GND VIN 2 "H" Output 2 Disable RESET Vsys GM7630 V0.1 Active 5 4 Output 1 10K www.gammamicro.com 1 MARKING INFORMATION & PIN CONFIGURATIONS (TOP VIEW) GM7630 AYWW VIN 1 Output 3 VIN 2 Output 1 DEL.CAP Output 2 Disable Control GND RESET A Y WW = Assembly Location = Year = Work Week ORDERING INFORMATION Ordering Number GM7630SIP10T Package Shipping 10- SIP H/ S 20 Units/ Tube GM7630 * For detail Ordering Number identification, please see last page. 2 ABSOLUTE MAXIMUM RATINGS SYMBOL PARAMETER RATINGS UNITS REMARK DC Input Voltage VIN 20 V - Disable Input Voltage VC 20 V - Output Current IO 0.5 A - Power Dissipation PD 1.5 W No Heatsink Junction Temperature TJ +150 °C - Topr 0 ~ +125 °C - Operating Temperature INTERNAL BLOCK DIAGRAM VIN1 VIN2 1 2 OVP 10µA DEL.CAP 3 Bandgap Reference 2.5V VIN1 + 9 Output 1 SCP Cd 100nF + RESET 6 50mV + SW Thermal Shut Down Vsys OVP A614 "Y" 7 + + - Control + - SCP SCP Output 2,3 10 Output 3 5 GND 8 Output 2 1.4V 4 Disable GM7630 10k VIN2 3 ELECTRICAL CHARACTERISTICS (Refer to test circuit VIN1=7.5V, VIN2=10.5V, TJ= 25°C, unless otherwise specified) Parameter Min Typ Max Unit VO1 IO1=10mA, 7.5V< VIN1< 14V 5mA < IO1< 500mA 5.0 4.9 5.1 5.1 5.2 5.3 V Output Voltage 2 VO2 IO2=10mA, 10.5V< VIN2< 18V 5mA < IO2< 500mA 7.84 7.7 8 8 8.16 8.3 V IO1,2=500mA, - - 2.5 V - - 50 80 mV Vd1,2 Line Regulation 1,2 DVO1,2 7.5V< VIN1< 14V 10.5V < VIN2< 18V IO1,2= 200mA Load Regulation 1, 2 DVO1,2 5mA < IO1 < 500mA 5mA < IO2< 500mA Vsys= 13V, IO3= 100mA - 0.1 100 160 mV 11.7 12 12.3 V Output Voltage 3 VO3 Line Regulation 3 DVO3 13V <VIN3< 18V IO3= 100mA - - 120 mV Load Regulation 3 DVO3 5mA < IO3 < 1A - - 250 mV Reset Pulse Delay Trd Cd= 100nF, Note 1 - 25 - ms Saturation Voltage in Reset Condition VrL I6= 5mA - - 0.4 V Leakage Current Pin 6 IrH V6= 10V - - 10 µA Output Voltage Thermal Drift STt 0°C < TJ < +125°C, Note 2 - 100 - ppm/°C Short Circuit Output Current Isc 1,2 VIN1=7.5V, VIN 2= 10.5V - - 1.6 A Disable Voltage High VdisH Output 2 Active 2.0 - - V Disable Voltage Low VdisL Output 2 Disabled - - 0.8 V Disable Bias Current Idis 0V < Vdis < 7V -100 - 2 µA Junction Temperature for TSD Ttsd Note 2 - 145 - °C - - 2 mA Quiescent Current Iq IO1= 10mA, Output2 Disabled Reset Threshold Voltage Vr K= VO1 Vrth Note 1 Reset Threshold Hysteresis GM7630 Condition Output Voltage 1 Dropout Output Voltage 1,2 4 Symbol K -0.4 K -0.25 K -0.1 V 50 mA 20 100 Notes: 1. To check the reset circuit ,the reset output is low to discharge the delay capacitor(=Cd). if it’s less than VO1-0.25V. And the reset output is high when the delay capacitor voltage linearly increased by the interal current source(10µA) if it’s more than VO1- 0.2V. The equations of delay time is same as below. Trd = (Cd X 2.5) / 10µA 2. These parameters, although guaranteed, are not 100% tested in production. 10-SIP H/ S PACKAGE OUTLINE DIMENSIONS 0.984 (TYP) 25.00 (TYP) 0.1575 ± 0.0055 4.00 ± 0.15 0.472 (TYP) 12.00 (TYP) 0.5905 ± 0.0055 15.0 ± 0.15 0.4725 ± 0.0115 12.0 ± 0.30 0.331 ± 0.006 8.40 ± 0.15 0.024 ± 0.004 0.60 ± 0.10 0.236 (MIN) 6.000 (MIN) 0.02 ± 0.004 0.50 ± 0.10 0.047 (TYP) 1.200 (TYP) 0.100 (TYP) 2.540 (TYP) 0.018 ± 0.004 0.45 ± 0.10 1.016 ± 0.008 25.8 ± 0.20 Inches ( mm ) ORDERING NUMBER GM 7630 SIP10 T Shipping T: Tube Circuit Type Package SIP10: 10- SIP H/ S GM7630 Gamma Micro. 5 6 GM7630