Genesys Logic, Inc. GL852 USB 2.0 MTT HUB Controller Datasheet Revision 1.14 Jul. 19, 2007 GL852 USB 2.0 MTT HUB Controller Copyright: Copyright © 2007 Genesys Logic Incorporated. All rights reserved. No part of the materials may be reproduced in any form or by any means without prior written consent of Genesys Logic, Inc. Disclaimer: ALL MATERIALS ARE PROVIDED “AS IS” WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY KIND. NO LICENSE OR RIGHT IS GRANTED UNDER ANY PATENT OR TRADEMARK OF GENESYS LOGIC INC.. GENESYS LOGIC HEREBY DISCLAIMS ALL WARRANTIES AND CONDITIONS IN REGARD TO MATERIALS, INCLUDING ALL WARRANTIES, IMPLIED OR EXPRESS, OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF INTELLECTUAL PROPERTY. IN NO EVENT SHALL GENESYS LOGIC BE LIABLE FOR ANY DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES RESULTING FROM LOSS OF INFORMATION OR PROFITS. PLEASE BE ADVISED THAT THE MATERIALS MAY CONTAIN ERRORS OR OMMISIONS. GENESYS LOGIC MAY MAKE CHANGES TO THE MATERIALS OR TO THE PRODUCTS DESCRIBED THEREIN AT ANY TIME WITHOUT NOTICE. Trademarks: is a registered trademark of Genesys Logic, Inc. All trademarks are the properties of their respective owners. Office: Genesys Logic, Inc. 12F, No. 205, Sec. 3, Beishin Rd., Shindian City, Taipei, Taiwan Tel: (886-2) 8913-1888 Fax: (886-2) 6629-6168 http://www.genesyslogic.com ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 2 GL852 USB 2.0 MTT HUB Controller Revision History Revision Date Description 1.00 07/07/2005 First Formal release 1.01 09/07/2005 Modify Pin Description, table3.3, p.12 1.02 09/15/2005 Modify HUB Interface ,table3.3 Pin Description, p.12 1.03 12/28/2005 Modify Pin List and Pin Descriptions of EE_CS, EE_DI, EE_SK, p.11~12 1.04 01/19/2006 Add AC Characteristics, Ch6.5, p.26 1.05 03/29/2006 Add Input Voltage for digital I/O(Ovcur1-4,Pself,Reset) pins, p.23 1.06 06/15/2006 Changed GL852-N to GL852 1.GL852 48 Pin Pinout, Pin List, Pin Description, p.10~13 Add GL852 QFN 48PIN 1.07 07/18/2006 Modify GL852 48 Pin QFN Package, p.30 1.08 09/05/2006 Modify Clock and Reset Interface of GL852 48 pin to 64 pin, p.14 1.09 11/03/2006 Modify 93C46 Configuration, Table 5.1, p.22 1.10 12/08/2006 Modify General Description, Ch1, p.7 1.11 03/12/2007 Modify RESET# Setting, Ch5.2.1, p.18 1.12 05/03/2007 Add “TJ” , Table 6.2, p.24 1.13 05/16/2007 Add 1.14 07/19/2007 Modify PGANG/SUSPND Setting, Ch5.2.2, p.19 “θ ”, Table 6.2, p.24 JA ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 3 GL852 USB 2.0 MTT HUB Controller TABLE OF CONTENTS CHAPTER 1 GENERAL DESCRIPTION................................................... 7 CHAPTER 2 FEATURES .............................................................................. 8 CHAPTER 3 PIN ASSIGNMENT ................................................................ 9 3.1 PINOUTS...................................................................................................... 9 3.2 PIN LIST.................................................................................................... 12 3.3 PIN DESCRIPTIONS ................................................................................... 13 CHAPTER 4 BLOCK DIAGRAM.............................................................. 15 CHAPTER 5 FUNCTION DESCRIPTION ............................................... 16 5.1 GENERAL .................................................................................................. 16 5.2 CONFIGURATION AND I/O SETTINGS ....................................................... 18 CHAPTER 6 ELECTRICAL CHARACTERISTICS............................... 24 6.1 MAXIMUM RATINGS................................................................................. 24 6.2 OPERATING RANGES ................................................................................ 24 6.3 DC CHARACTERISTICS ............................................................................ 24 6.4 POWER CONSUMPTION ............................................................................ 26 6.5 AC CHARACTERISTICS ............................................................................ 27 CHAPTER 7 PACKAGE DIMENSION..................................................... 28 CHAPTER 8 ORDERING INFORMATION ............................................ 31 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 4 GL852 USB 2.0 MTT HUB Controller LIST OF FIGURES －GL852 64 PIN LQFP PINOUT DIAGRAM ...................................................... 9 FIGURE 3.1－ FIGURE 3.2－ －GL852 48 PIN LQFP PINOUT DIAGRAM .................................................... 10 FIGURE 3.2－ －GL852 48 PIN QFN PINOUT DIAGRAM ...................................................... 11 FIGURE 4.1 - GL852 BLOCK DIAGRAM (MULTIPLE TT) .................................................. 15 FIGURE 5.1 - OPERATING IN USB 1.1 SCHEME.................................................................. 17 FIGURE 5.2 - OPERATING IN USB 2.0 SCHEME.................................................................. 18 FIGURE 5.3 - RESET# (EXTERNAL RESET) SETTING AND APPLICATION......................... 19 FIGURE 5.4 - POWER ON SEQUENCE OF GL852................................................................. 19 FIGURE 5.5 - TIMING OF PGANG/SUSPND STRAPPING ................................................. 20 FIGURE 5.6 - GANG MODE SETTING ................................................................................ 20 FIGURE 5.7 - SELF/BUS POWER SETTING ....................................................................... 21 FIGURE 5.8 - LED CONNECTION ....................................................................................... 21 FIGURE 5.9 - SCHEMATICS BETWEEN GL852 AND 93C46................................................ 23 FIGURE 7.1 - GL852 64 PIN LQFP PACKAGE ................................................................... 28 FIGURE 7.2 – GL852 48 PIN LQFP PACKAGE .................................................................. 29 FIGURE 7.2 – GL852 48 PIN QFN PACKAGE .................................................................... 30 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 5 GL852 USB 2.0 MTT HUB Controller LIST OF TABLES TABLE 3.1－ －GL852 64 PIN LIST ....................................................................................... 12 TABLE 3.2－ －GL852 48 PIN LIST ....................................................................................... 12 TABLE 3.3 - PIN DESCRIPTIONS ......................................................................................... 13 TABLE 5.1 - 93C46 CONFIGURATION ................................................................................ 22 TABLE 6.1 - MAXIMUM RATINGS ...................................................................................... 24 TABLE 6.2 - OPERATING RANGES ...................................................................................... 24 TABLE 6.3 - DC CHARACTERISTICS EXCEPT USB SIGNALS ............................................ 24 TABLE 6.4 - DC CHARACTERISTICS OF USB SIGNALS UNDER FS/LS MODE.................. 25 TABLE 6.5 - DC CHARACTERISTICS OF USB SIGNALS UNDER HS MODE ....................... 25 TABLE 6.6 - DC SUPPLY CURRENT .................................................................................... 26 TABLE 6.7 - AC CHARACTERISTICS OF EEPROM INTERFACE ....................................... 27 TABLE 8.1 - ORDERING INFORMATION ............................................................................. 31 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 6 GL852 USB 2.0 MTT HUB Controller CHAPTER 1 GENERAL DESCRIPTION GL852 is Genesys Logic’s brand new Hub solutions which fully comply with Universal Serial Bus Specification Revision 2.0. This series includes GL852. GL852 embeds an 8-bit RISC processor to manipulate the control/status registers and respond to the requests from USB host. Firmware of GL852 will control its general purpose I/O (GPIO) to access the external EEPROM and then respond to the host the customized PID and VID configured in the external EEPROM. Default settings in the internal mask ROM is responded to the host without having external EEROM. GL852 is designed for customers with much flexibility. The more complicated settings such as PID, VID, and number of downstream ports settings are easily achieved by programming the external EEPROM (Ref. to Chapter 5). Each downstream port of GL852 supports two-color (green/amber) status LEDs to indicate normal/abnormal status. To fully meet the performance requirement, GL852 series is a multiple TT hub solution to provide every down stream port with a TT. With the dedicated TT in each down stream port, GL852 can provide the best performance even connect with several Full/Low-Speed devices and running heavy bandwidth-consuming operations concurrently. *TT (transaction translator) is the main traffic control engine in an USB 2.0 hub to handle the unbalanced traffic speed between the upstream port and the downstream ports. Product Name Package type Power mode LED support GL852 64LQFP Individual/Gang Green/Amber GL852 48LQFP Individual/Gang Green/Amber GL852 48QFN Individual/Gang Green/Amber ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 7 GL852 USB 2.0 MTT HUB Controller CHAPTER 2 FEATURES • Compliant to USB specification Revision 2.0 − 4 downstream ports − Upstream port supports both high-speed (HS) and full-speed (FS) traffic − Downstream ports support HS, FS, and low-speed (LS) traffic − 1 control pipe (endpoint 0, 64-byte data payload) and 1 interrupt pipe (endpoint 1, 1-byte data payload) − Backward compatible to USB specification Revision 1.1 • On-chip 8-bit micro-processor − RISC-like architecture − USB optimized instruction set − Dual cycle instruction execution − Performance: 6 MIPS @ 12MHz − With 64-byte RAM and 2K internal ROM − Support customized PID, VID by reading external EEPROM − Support downstream port configuration by reading external EEPROM • Multiple Transaction translator (MTT) − MTT provides respective TT control logics for each downstream port. This is a performance better choice for USB 2.0 hub. • Each downstream port supports two-color status indicator, with automatic and manual modes compliant to USB specification Revision 2.0 • Support both individual and gang modes of power management and over-current detection for downstream ports • • • • • • • • • • • Support gang mode of power management and over-current detection for downstream ports Conform to bus power requirements Automatic switching between self-powered and bus-powered modes Integrate USB 2.0 transceiver PLL embedded with external 12 MHz crystal Operate on 3.3 Volts Embed serial resister for USB signals and integrate pull-up resister for upstream USB signal Improve output drivers with slew-rate control for EMI reduction Internal power-fail detection for ESD recovery 64-pin LQFP package , 48-pin LQFP package , 48-pin QFN package Applications: − Stand-alone USB hub − Monitor hub − PC motherboard USB hub, Docking of notebook − Any compound device to support USB HUB function ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 8 GL852 USB 2.0 MTT HUB Controller CHAPTER 3 PIN ASSIGNMENT GREEN2/EE_DO DVDD DGND AMBER3 GREEN3 PWREN3# OVCUR3# PWREN4# OVCUR4# TEST RESET# DVDD DGND AMBER4 GREEN4 NC 3.1 Pinouts 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 AMBER2/EE_DI 49 32 DP4 PSELF 50 31 DM4 DGND 51 30 NC DVDD 52 29 AGND PGANG/SUSPND 53 28 AVDD OVCUR2# 54 27 NC PWREN2# 55 26 DP3 OVCUR1# 56 25 DM3 PWREN1# 57 24 NC DGND 58 23 AGND DVDD 59 22 AVDD GREEN1/EE_SK 60 21 X2 AMBER1/EE_CS 61 20 X1 DGND 62 19 AGND DVDD 63 18 AVDD AVDD 64 17 RREF GL852 5 6 7 8 9 10 11 12 13 14 15 16 NC DM1 DP1 NC AVDD ANGD NC DM2 DP2 NC NC DM0 4 NC 3 NC 2 DP0 1 AGND LQFP - 64 －GL852 64 Pin LQFP Pinout Diagram Figure 3.1 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 9 AMBER2/EE_DI GREEN2 DVDD AMBER3 GREEN3 PWREN3# OVCUR3# PWREN4# OVCUR4# TEST RESET# DVDD 36 35 34 33 32 31 30 29 28 27 26 25 GL852 USB 2.0 MTT HUB Controller PSELF 37 24 AMBER4 DVDD 38 23 GREEN4 PGANG 39 22 DP4 OVCUR2# 40 21 DM4 PWREN2# 41 20 AGND OVCUR1# 42 19 AVDD PWREN1# 43 18 DP3 DVDD 44 17 DM3 GREEN1/EE_SK 45 16 AVDD AMBER1/EE_CS 46 15 X2 DGND 47 14 X1 DVDD 48 13 AGND GL852 3 4 5 6 7 8 9 10 11 12 DP0 DM1 DP1 AVDD AGND DM2 DP2 RREF AVDD 2 AGND DM0 1 AVDD LQFP - 48 －GL852 48 Pin LQFP Pinout Diagram Figure 3.2 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 10 AMBER2/EE_DI GREEN2 DVDD AMBER3 GREEN3 PWREN3# OVCUR3# PWREN4# OVCUR4# TEST RESET# DVDD 36 35 34 33 32 31 30 29 28 27 26 25 GL852 USB 2.0 MTT HUB Controller PSELF 37 24 AMBER4 DVDD 38 23 GREEN4 PGANG 39 22 DP4 OVCUR2# 40 21 DM4 PWREN2# 41 20 AGND OVCUR1# 42 19 AVDD PWREN1# 43 18 DP3 DVDD 44 17 DM3 GREEN1/EE_SK 45 16 AVDD AMBER1/EE_CS 46 15 X2 DGND 47 14 X1 DVDD 48 13 AGND GL852 1 2 3 4 5 6 7 8 9 10 11 12 AVDD AGND DM0 DP0 DM1 DP1 AVDD AGND DM2 DP2 RREF AVDD QFN - 48 －GL852 48 Pin QFN Pinout Diagram Figure 3.2 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 11 GL852 USB 2.0 MTT HUB Controller 3.2 Pin List －GL852 64 Pin List Table 3.1 Pin# Pin Name Type Pin# Pin Name Type Pin# Pin Name Type Pin# Pin Name AMBER2/ EE_DI Type 1 AGND P 17 RREF B 33 NC - 49 2 NC - 18 AVDD P 34 GREEN4 O 50 PSELF I 3 DM0 B 19 AGND P 35 AMBER4 O 51 DGND P 4 DP0 B 20 X1 I 36 DGND P P 5 NC - 21 X2 O 37 DVDD P B 6 NC - 22 AVDD P 38 RESET# I 52 DVDD PGANG/ 53 SUSPND 54 OVCUR2# 7 NC - 23 AGND P 39 TEST I 55 PWREN2# O 8 DM1 B 24 NC - 40 OVCUR4# I 56 OVCUR1# I 9 DP1 B 25 DM3 B 41 PWREN4# O 57 PWREN1# O 10 NC - 26 DP3 B 42 OVCUR3# I 58 DGND P 11 AVDD P 27 NC - 43 PWREN3# O 59 DVDD P GREEN1/ 60 EE_SK AMBER1/ 61 EE_CS O I 12 AGND P 28 AVDD P 44 GREEN3 O 13 NC - 29 AGND P 45 AMBER3 O 14 DM2 B 30 NC - 46 DGND P 62 DGND P 15 DP2 B 31 DM4 B 47 DVDD P 63 AVDD P 16 NC - 32 DP4 B 48 B 64 AVDD P GREEN2/ EE_DO O O －GL852 48 Pin List Table 3.2 Pin# Pin Name Type Pin# Pin Name Type Pin# Pin Name Type Pin# Pin Name Type 1 AVDD P 13 AGND P 25 DVDD P 37 PSELF I 2 AGND P 14 X1 I 26 RESET# I 38 DVDD P 3 DM0 B 15 X2 O 27 TEST I 39 PGANG B 4 DP0 B 16 AVDD P 28 OVCUR4# I 40 OVCUR2# I 5 DM1 B 17 DM3 B 29 PWREN4# O 41 PWREN2# O 6 DP1 B 18 DP3 B 30 OVCUR3# I 42 OVCUR1# I 7 AVDD P 19 AVDD P 31 PWREN3# O 43 PWREN1# O 8 AGND P 20 AGND P 32 GREEN3 O 44 DVDD P 9 DM2 B 21 DM4 B 33 AMBER3 O 45 GREEN1/ EE_SK O B 22 DP4 B 34 DVDD P 46 AMBER1/ EE_CS O 10 DP2 ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 12 GL852 USB 2.0 MTT HUB Controller 11 RREF B 23 GREEN4 O 35 GREEN2/ EE_DO O 47 DGND P 12 AVDD P 24 AMBER4 O 36 AMBER2/ EE_DI O 48 DVDD P 3.3 Pin Descriptions Table 3.3 - Pin Descriptions USB Interface GL852 GL852 64 Pin# 48Pin# DM0,DP0 3,4 3,4 B USB signals for USPORT DM1,DP1 8,9 5,6 B USB signals for DSPORT1 DM2,DP2 14,15 9,10 B USB signals for DSPORT2 DM3,DP3 25,26 17,18 B USB signals for DSPORT3 DM4,DP4 31,32 21,22 B RREF 17 11 B USB signals for DSPORT4 A 680Ω resister must be connected between RREF and analog ground (AGND). Pin Name I/O Type Description Note: USB signals must be carefully handled in PCB routing. For detailed information, please refer to GL852 Design Guideline. HUB Interface GL852 GL852 64 Pin# 48Pin# OVCUR1#~4 56,54, 42,40 42,40,30,28 PWREN1#~4 57,55, 43,41 GREEN1~4 60,48, 44,34 AMBER1~4 61,49, 45,35 PSELF 50 PGANG/ SUSPND 53 Pin Name I/O Type Description Active low. Over current indicator for DSPORT1~4 OVCUR1# is the only over current flag for GANG mode. Active low. Power enable output for DSPORT1~4 PWREN1# is the only power-enable output for GANG 43,41,31,29 O mode. 1,3,4: O Green LED indicator for DSPORT1~4 45,35,32,23 2: B *GREEN[1~2] are also used to access the external EEPROM For detailed information, please refer to Chapter 5. (pd) O Amber LED indicator for DSPORT1~4 46,36,33,24 (pd) *Amber [1~2] are also used to access the external EEPROM 0: GL852 is bus-powered. 37 I 1: GL852 is self-powered. This pin is default put in input mode after power-on reset. Individual/gang mode is strapped during this period. After the strapping period, this pin will be set to output mode, and then output high for normal mode. 39 B When GL852 is suspended, this pin will output low. *For detailed explanation, please see Chapter 5 Gang input:1, output: 0@normal, 1@suspend Individual input:0, output: 1@normal, 0@suspend I (pu) ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 13 GL852 USB 2.0 MTT HUB Controller Clock and Reset Interface GL852 GL852 64Pin# 48Pin# X1 20 14 I 12MHz crystal clock input. X2 21 15 O RESET# 38 26 I 12MHz crystal clock output. Active low. External reset input, default pull high 10KΩ. When RESET# = low, whole chip is reset to the initial state. Pin Name I/O Type Description System Interface Pin Name TEST GL852 GL852 64 Pin# 48Pin# 39 27 I/O Type I (pd) Description 0: Normal operation. 1: Chip will be put in test mode. Power / Ground Pin Name AVDD AGND DVDD DGND NC GL852 GL852 64 Pin# 48Pin# 11,18,22, 1,7,12,16,19 28,64 1,12,19, 23,29 37,47, 52,59 36,46, 51,58,62 2,5~7,10, 13,16,24, 27,30,33 I/O Type Description P 3.3V analog power input for analog circuits. 2,8,13,20, P Analog ground input for analog circuits. 25,34,38,44, 48 P 3.3V digital power input for digital circuits 47 P Digital ground input for digital circuits. - - No connection Note: Analog circuits are quite sensitive to power and ground noise. PCB layout must take care the power routing and the ground plane. For detailed information, please refer to GL852 Design Guideline. Notation: Type O I B B/I B/O P A SO pu pd odpu Output Input Bi-directional Bi-directional, default input Bi-directional, default output Power / Ground Analog Automatic output low when suspend Internal pull up Internal pull down Open drain with internal pull up ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 14 GL852 USB 2.0 MTT HUB Controller CHAPTER 4 BLOCK DIAGRAM 12MHz D+ D- USPORT PLL RAM ROM GPIO FRTIMER Transceiver x40, x10 CPU USPORT Control/Status UTMI SIE Logic REPEATER Register TT TT TT TT (Transaction Translator) (Transaction Translator) (Transaction Translator) (Transaction Translator) REPEATER / TT Routing Logic DSPORT1 Logic DSPORT2 Logic DSPORT3 Logic DSPORT4 Logic DSPORT DSPORT DSPORT DSPORT Transceiver Transceiver Transceiver Transceiver D+ D- LED/ OVCUR/ PWRENB D+ D- LED/ OVCUR/ PWRENB D+ D- LED/ OVCUR/ PWRENB D+ D- LED/ OVCUR/ PWRENB Figure 4.1 - GL852 Block Diagram (multiple TT) ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 15 GL852 USB 2.0 MTT HUB Controller CHAPTER 5 FUNCTION DESCRIPTION 5.1 General 5.1.1 USPORT Transceiver USPORT (upstream port) transceiver is the analog circuit that supports both full-speed and high-speed electrical characteristics defined in chapter 7 of USB specification Revision 2.0. USPORT transceiver will operate in full-speed electrical signaling when GL852 is plugged into a 1.1 host/hub. USPORT transceiver will operate in high-speed electrical signaling when GL852 is plugged into a 2.0 host/hub. 5.1.2 PLL (Phase Lock Loop) GL852 contains a 40x PLL. PLL generates the clock sources for the whole chip. The generated clocks are proven quite accurate that help in generating high speed signal without jitter. 5.1.3 FRTIMER This module implements hub (micro)frame timer. The (micro)frame timer is derived from the hub’s local clock and is synchronized to the host (micro)frame period by the host generated Start of (micro)frame (SOF). FRTIMER keeps tracking the host’s SOF such that GL852 is always safely synchronized to the host. The functionality of FRTIMER is described in section 11.2 of USB Specification Revision 2.0. 5.1.4 µC µC is the micro-processor unit of GL852. It is an 8-bit RISC processor with 2K ROM and 64 bytes RAM. It operates at 6MIPS of 12Mhz clock to decode the USB command issued from host and then prepares the data to respond to the host. In addition, µC can handle GPIO (general purpose I/O) settings and reading content of EEPROM to support high flexibility for customers of different configurations of hub. These configurations include self/bus power mode setting, individual/gang mode setting, downstream port number setting, device removable/non-removable setting, and PID/VID setting. 5.1.5 UTMI (USB 2.0 Transceiver Macrocell Interface) UTMI handles the low level USB protocol and signaling. It’s designed based on the Intel’s UTMI specification 1.01. The major functions of UTMI logic are to handle the data and clock recovery, NRZI encoding/decoding, Bit stuffing /de-stuffing, supporting USB 2.0 test modes, and serial/parallel conversion. 5.1.6 USPORT logic USPORT implements the upstream port logic defined in section 11.6 of USB specification Revision 2.0. It mainly manipulates traffics in the upstream direction. The main functions include the state machines of Receiver and Transmitter, interfaces between UTMI and SIE, and traffic control to/from the REPEATER and TT. 5.1.7 SIE (Serial Interface Engine) μ SIE handles the USB protocol defined in chapter 8 of USB specification Revision 2.0. It co-works with C to play the role of the hub kernel. The main functions of SIE include the state machine of USB protocol flow, CRC check, PID error check, and timeout check. Unlike USB 1.1, bit stuffing/de-stuffing is implemented in UTMI, not in SIE. 5.1.8 Control/Status register Control/Status register is the interface register between hardware and firmware. This register contains the information necessary to control endpoint0 and endpoint1 pipelines. Through the firmware based architecture, GL852 possesses higher flexibility to control the USB protocol easily and correctly. 5.1.9 REPEATER Repeater logic implements the control logic defined in section 11.4 and section 11.7 of USB specification Revision 2.0. REPEATER controls the traffic flow when upstream port and downstream port are signaling in the same speed. In addition, REPEATER will generate internal resume signal whenever a wakeup event is issued under the situation that hub is globally suspended. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 16 GL852 USB 2.0 MTT HUB Controller 5.1.10. TT (Transaction Translator) TT implements the control logic defined in section 11.14 ~ 11.22 of USB specification Revision 2.0. TT basically handles the unbalanced traffic speed between the USPORT (operating in HS) and DSPORTS (operating in FS/LS) of hub. GL852 adopts multiple TT architecture to provide the most performance effective solution. Multiple TT provides control logics for each downstream port respectively. 5.1.11 REPEATER/TT routing logic REPEATER and TT are the major traffic control machines in the USB 2.0 hub. Under situation that USPORT and DSPORT are signaling in the same speed, REPEATER/TT routing logic switches the traffic channel to the REPEATER. Under situation that USPORT is in the high speed signaling and DSPORT is in the full/low speed signaling, REPEATER/TT routing logic switches the traffic channel to the TT. 5.1.11.1 Connected to 1.1 Host/Hub If an USB 2.0 hub is connected to the downstream port of an USB 1.1 host/hub, it will operate in USB 1.1 mode. For an USB 1.1 hub, both upstream direction traffic and downstream direction traffic are passing through REPEATER. That is, the REPEATER/TT routing logic will route the traffic channel to the REPEATER. USB1.1 HOST/HUB USPORToperating in FS signaling Traffic channel is routed to REPEATER REPEATER TT TT DSPORT operating in FS/LS signaling Figure 5.1 - Operating in USB 1.1 scheme 5.1.11.2 Connected to USB 2.0 Host/Hub If an USB 2.0 hub is connected to an USB 2.0 host/hub, it will operate in USB 2.0 mode. The upstream port signaling is in high speed with bandwidth of 480 Mbps under this environment. The traffic channel will then be routed to the REPEATER when the device connected to the downstream port is signaling also in high speed. On the other hand, the traffic channel will then be routed to TT when the device connected to the downstream port is signaling in full/low speed. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 17 GL852 USB 2.0 MTT HUB Controller USB2.0 HOST/HUB USPORToperating in HS signaling HS vs. HS: Traffic channel is routed to REPEATER REPEATER DSPORT operating in HS signaling TT HS vs. FS/LS: Traffic channel is routed to TT TT DSPORT operating in FS/LS signaling Figure 5.2 - Operating in USB 2.0 scheme 5.12 DSPORT logic DSPORT (downstream port) logic implements the control logic defined in section 11.5 of USB specification Revision 2.0. It mainly manipulates the state machine, the connection/disconnection detection, over current detection and power enable control, and the status LED control of the downstream port. Besides, it also output the control signals to the DSPORT transceiver. 5.13 DSPORT Transceiver DSPORT transceiver is the analog circuit that supports high-speed, full-speed, and low-speed electrical characteristics defined in chapter 7 of USB specification Revision 2.0. In addition, each DSPORT transceiver accurately controls its own squelch level to detect the detachment and attachment of devices. 5.2 Configuration and I/O Settings 5.2.1 RESET# Setting GL852 integrates in the pull-up 1.5KΩ resister of the upstream port. When RESET# is enabled, the internal 1.5KΩ pull-up resister will be disconnected to the 3.3V power. To meet the requirement (p.141) of the USB 2.0 specification, pull-up resister should be disconnected while lacking of USB cable power (Vbus). Therefore, we suggest designing the RESET# circuit as following figure to meet the requirement mentioned above. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 18 GL852 USB 2.0 MTT HUB Controller Figure 5.3 - RESET# (External Reset) setting and application GL852 internally contains a power on reset circuit. The power on sequence is depicted in the next picture. To fully control the reset process of GL852, we suggest the reset time applied in the external reset circuit should longer than that of the internal reset circuit. VCC(3.3V) Power good voltage, 2.5~2.8V ≒ 2.7 μs Internal reset External reset Figure 5.4 - Power on sequence of GL852 5.2.2 PGANG/SUSPND Setting To save pin count, GL852 uses the same pin to decide individual/gang mode as well as to output the suspend flag. The individual/gang mode is decided within 20us after power on reset. Then, about 50ms later, this pin is changed to output mode. GL852 outputs the suspend flag once it is globally suspended. For individual mode, a pull low resister greater than 100KΩ should be placed. For gang mode, a pull high resister which greater than 100KΩ should be placed. In figure 5.6, we also depict the suspend LED indicator schematics. It should be noticed that the polarity of LED must be followed, otherwise the suspend current will be over spec limitation (2.5mA). ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 19 GL852 USB 2.0 MTT HUB Controller RESET# 50 ms GANG_CTL Output mode, indicating GL852 is in normal mode or suspend mode Input mode, strapping to decide individual or gang mode Figure 5.5 - Timing of PGANG/SUSPND strapping GAND Mode DVDD(3.3V) "0": Individual Mode "1": GANG Mode DVDD(3.3V) 100K ohm Suspend LED Indicator PGANG SUSPNDO GANG_CTL 100K ohm Suspend LED Indicator Inside GL852 On PCB Individual Mode Figure 5.6 - GANG Mode Setting 5.2.3 SELF/BUS Power Setting GL852 can operate under bus power and conform to the power consumption limitation completely (suspend current < 2.5 mA, normal operation current < 100 mA). By setting PSELF, GL852 can be configured as a bus-power or a self-power hub. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 20 GL852 USB 2.0 MTT HUB Controller 1: Power Self PSELF 0: Power Bus Inside GL852 On PCB Figure 5.7 - SELF/BUS Power Setting 5.2.4 LED Connections GL852 controls the LED lighting according to the flow defined in section 11.5.3 of Universal Serial Bus Specification Revision2.0. Both manual mode and Automatic mode are supported in GL852. When GL852 is globally suspended, GL852 will turn off the LED to save power. AMBER/GREEN LED DGND Inside GL852 On PCB Figure 5.8 - LED Connection 5.2.5 EEPROM Setting GL852 replies to host commands by the default settings in the internal ROM. GL852 also offers the ability to reply to the host according to the settings in the external EEPROM(93C46). The following table shows the configuration of 93C46. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 21 GL852 USB 2.0 MTT HUB Controller Table 5.1 - 93C46 Configuration Unit: Byte 00 00h 10h VID_L 01 02 03 04 05 VID_H PID_L PID_H CHKSUM FF 06 07 PORT DEVICE REMOVABLE NUMBER 08 09 0A 0B 0C 0D 0E 0F MaxPower FF FF FF FF FF Vendor string (ASC II code) 30h end PRODUCT LENGTH start Product String(ASC II code) 50h 60h 70h FF VENDOR LENGTH start 20h 40h FF end SERIAL NUMBER LENGTH start Serial Number String(ASC II code) end Note: 1. VID_H/VID_L: high/low byte of VID value 2. PID_H/PID_L: high/low byte of PID value 3. CHKSUM: CHKSUM must equal to VID_H + VID_L + PID_H + PID_L + 1,otherwise firmware will ignore the EEPROM settings. 4. PORT_NO: port number, value must be 1~4. 5. MaxPower : Describe the maximum power consumption, range=0Ma~500Ma . Value -> 00H~FAH (unit = 2Ma) 6. DEVICE REMOVALBE: PORT4 PORT3 PORT2 PORT1 REMOVABLE REMOVABLE REMOVABLE REMOVABLE 0: Device attached to this port is removable. 1: Device attached to this port is non-removable. - 7. VENDOR LENGTH: offset 10h contains the length of the vendor string. Values of vendor string is contained from 11h~3Fh. 8. PRODUCT LENGTH: offset 40h contains the length of product string. Values of product string is contained from 41h~6Fh. 9. SERIAL NUMBER LENGTH: offset 70h contains the value of serial number string. Values of serial number string is contained after offset 71h. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 22 GL852 USB 2.0 MTT HUB Controller The schematics between GL852 and 93C46 is depicted in the following figures: DVDD EE_CS CS VCC EE_SK SK NC EE_DI DI NC EE_DO DO GND 93C46 Figure 5.9 - Schematics Between GL852 and 93C46 GL852 firstly verifies the check sum after power on reset. If the check sum is correct, GL852 will take the configuration of 93C46 as part of the descriptor contents. To prevent the content of 93C46 from being over-written, amber LED will be disabled when 93C46 exists. ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 23 GL852 USB 2.0 MTT HUB Controller CHAPTER 6 ELECTRICAL CHARACTERISTICS 6.1 Maximum Ratings Table 6.1 - Maximum Ratings Symbol Parameter Min. Max. Unit VCC Power Supply -0.5 +3.6 V VIN Input Voltage for digital I/O(EE_DO) pins -0.5 +3.6 V VIN Input Voltage for digital I/O(Ovcur1-4,Pself,Reset) pins -0.5 +5.25 V Input Voltage for USB signal (DP, DM) pins -0.5 +3.6 V +100 o VINUSB TS FOSC Storage Temperature under bias -60 Frequency C 12 MHz ± 0.05% 6.2 Operating Ranges Table 6.2 - Operating Ranges Symbol Parameter Min. Typ. Max. Unit VCC Power Supply 3.0 3.3 3.6 V VIND Input Voltage for digital I/O pins -0.5 3.3 3.6 V Input Voltage for USB signal (DP, DM) pins 0.5 3.3 3.6 V 70 o C 125 o C VINUSB TA TJ θ Ambient Temperature 0 Absolute maximum junction temperature - - o 52.2 - Min. Typ. Max. Unit Power Dissipation 70 - 190 mA VDD Power Supply Voltage 3 3.3 3.6 V VIL LOW level input voltage - - 0.9 V VIH HIGH level input voltage 2.0 - - V VTLH LOW to HIGH threshold voltage 1.36 1.48 1.62 V VTHL HIGH to LOW threshold voltage 1.36 1.48 1.62 V VOL LOW level output voltage when IOL=8mA - - 0.4 V VOH HIGH level output voltage when IOH=8mA Leakage current for pads with internal pull up or pull down resistor Pad internal pull down resister 2.4 - - V - - 30 µA 81K 103K 181K Ω JA Thermal Characteristics 48 LQFP 0 - C/W 6.3 DC Characteristics Table 6.3 - DC Characteristics Except USB Signals Symbol PD IOLK RDN Parameter ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 24 GL852 USB 2.0 MTT HUB Controller RUP Pad internal pull up resister 81K 103K 181K Ω Table 6.4 - DC Characteristics of USB Signals Under FS/LS Mode Symbol Parameter Min. Typ. Max. Unit VOL DPF/DMF static output LOW(RL of 1.5K to 3.6V ) 0 - 0.3 V VOH DPF/DMF static output HIGH (RL of 15K to GND ) 2.8 - 3.6 V VDI Differential input sensitivity 0.2 - - V VCM Differential common mode range 0.8 - 2.5 V VSE Single-ended receiver threshold 0.2 - - V CIN Transceiver capacitance - - 20 pF ILO Hi-Z state data line leakage -10 - +10 µA Driver output resistance 28 - 43 Ω ZDRV Table 6.5 - DC Characteristics of USB Signals Under HS Mode Symbol Parameter Min. Typ. Max. Unit VOL DPH/DMH static output LOW(RL of 1.5K to 3.6V ) - - 0.1 V CIN Transceiver capacitance 4 4.5 5 pF ILO Hi-Z state data line leakage -5 0 +5 µA Driver output resistance for USB 2.0 HS 48 45 42 Ω ZDRV ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 25 GL852 USB 2.0 MTT HUB Controller 6.4 Power Consumption Table 6.6 - DC Supply Current Condition Symbol Active ports ISUSP Host Suspend *2 4 3 ICC 2 1 No Active Typ. Unit 510/800*1 µA Device F F 83 mA H H 187 mA H F 107 mA F F 82 mA H H 170 mA H F 106 mA F F 81 mA H H 147 mA H F 105 mA F F 79 mA H H 124 mA H F 104 mA F 78 mA H 102 mA *1: 48/64-pin package types *2: F: Full-Speed, H: High-Speed ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 26 GL852 USB 2.0 MTT HUB Controller 6.5 AC Characteristics Symbol Parameter Min Typ Max tCSS CS Setup Time 3.0 tCSH CS Hold Time 3.0 tSKH SK High Time 1.0 tSKL SK Low Time 2.2 tDIS DI Setup Time 1.8 tDIH DI Hold Time 2.4 tPD1 Output Delay to “1” 1.8 tPD0 Output Delay to “0” 1.8 Units us Table 6.7 - AC Characteristics of EEPROM Interface ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 27 GL852 USB 2.0 MTT HUB Controller CHAPTER 7 PACKAGE DIMENSION D D1 A D2 A2 48 33 49 N : Normal package G : Green package B GL852 AAAAAAAGAA YWWXXXXXXXX Date Code Version No. Lot Code 17 64 16 4X 1 4X e 0- 1 b aaa C A B D bbb H A B D L1 E2 E E1 32 InternalNo . A A1 0.05 S D c ddd M C A B s D s 0- C SEATING PLANE ccc C 0- 2 R1 R2 H GAGE PLANE 0.25mm S L 0- 3 NOTES : 1. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 mm PER SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE DIMENSIONS INCLUDING MOLD MISMATCH. DIMENSION b DOES NOT INCLUDE DAMBAR 2. PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE MAXIMUM b DIMENSION BY MORE THAN 0.08mm. DAMBAR CAN NOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD IS 0.07mm. CONTROL DIMENSIONS ARE IN MILLIMETERS. MILLIMETER INCH SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. 1.60 0.063 A 0.006 0.05 0.15 0.002 A1 1.35 1.40 1.45 0.053 0.055 0.057 A2 12.00 BASIC 0.472 BASIC D 12.00 BASIC 0.472 BASIC E D1 10.00 BASIC 0.393 BASIC E1 10.00 BASIC 0.393 BASIC 7.50 BASIC 0.295 BASIC D2 7.50 BASIC 0.295 BASIC E2 R1 0.08 0.003 R2 0.08 0.20 0.003 0.008 00 3.5 7 0 3.5 7 0 0 0- 1 0- 2 11 12 13 11 12 13 0- 3 11 12 13 11 12 13 0.20 0.004 0.008 0.09 c 0.45 0.60 0.75 0.018 0.024 0.030 L 1.00 REF 0.039 REF L1 0.20 0.008 S 0.27 0.007 0.008 0.011 0.17 0.20 b 0.50 BASIC 0.020 BASIC e TOLERANCES OF FORM AND POSITION aaa 0.20 0.008 0.008 0.20 bbb 0.08 0.003 ccc 0.08 0.003 ddd Figure 7.1 - GL852 64 Pin LQFP Package ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 28 GL852 USB 2.0 MTT HUB Controller D D1 A D2 A2 25 36 37 24 N : Normal package G : Green package Internal No. B GL852 AAAAAAAGAA YWWXXXXXXXX Date Code Version No. Lot Code 48 13 12 4X 1 e 4X b 0- 1 C ccc C 0- 2 R1 R2 GAGE PLANE 0.25mm L 0- 3 NOTES : 1. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 mm PER SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE DIMENSIONS INCLUDING MOLD MISMATCH. 2. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE MAXIMUM b DIMENSION BY MORE THAN 0.08mm. DAMBAR CAN NOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD IS 0.07mm. c ddd M C A B s D s 0- S aaa C A B D bbb H A B D L1 E2 E E1 A H A1 0.05 S D SEATING PLANE CONTROL DIMENSIONS ARE IN MILLIMETERS. MILLIMETER INCH SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. 1.60 0.063 A 0.006 0.05 0.15 0.002 A1 1.35 A2 1.40 1.45 0.053 0.055 0.057 9.00 BASIC 0.354 BASIC D E 9.00 BASIC 0.354 BASIC 0.276 BASIC D1 7.00 BASIC E1 7.00 BASIC 0.276 BASIC 5.50 BASIC D2 0.217 BASIC 5.50 BASIC 0.217 BASIC E2 R1 0.08 0.003 R2 0.08 0.20 0.003 0.008 00° 3.5° 7° 0° 3.5° 7° 0° 0- 1 0° 0- 2 11° 12° 13° 11° 12° 13° 0- 3 11° 12° 13° 11° 12° 13° 0.09 0.20 0.004 0.008 c 0.45 0.60 0.75 0.018 0.024 0.030 L L1 1.00 REF 0.039 REF 0.20 0.008 S 0.17 0.20 0.27 0.007 0.008 0.011 b 0.50 BASIC 0.020 BASIC e TOLERANCES OF FORM AND POSITION aaa 0.20 0.008 0.008 bbb 0.20 0.08 0.003 ccc 0.08 0.003 ddd Figure 7.2 – GL852 48 Pin LQFP Package ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 29 GL852 USB 2.0 MTT HUB Controller Figure 7.2 – GL852 48 Pin QFN Package ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 30 GL852 USB 2.0 MTT HUB Controller CHAPTER 8 ORDERING INFORMATION Table 8.1 - Ordering Information Part Number Package Normal/Green Version Status GL852-MSNXX 64-pin LQFP Normal Package XX Available GL852-MNNXX 48-pin LQFP Normal Package XX Available GL852-MSGXX 64-pin LQFP Green Package XX Available GL852-MNGXX 48-pin LQFP Green Package XX Available GL852-ONGXX 48-pin QFN Green Package XX Available ©2000-2007 Genesys Logic Inc. - All rights reserved. Page 31