GENNUM GS4911B

GS4911B/GS4910B
HD/SD/Graphics Clock and
Timing Generator with GENLOCK
GS4911B/GS4910B Data Sheet
Key Features
Description
Video Clock Synthesis
The GS4911B is a highly flexible, digitally controlled
clock synthesis circuit and timing generator with
genlock capability. It can be used to generate video and
audio clocks and timing signals, and allows multiple
devices to be genlocked to an input reference.
•
•
•
•
•
•
Generates any video or graphics clock up to 165MHz
Pre-programmed for 8 video and 13 graphics clocks
Accuracy of free-running clock frequency limited only by
crystal reference
One differential and two single-ended video/graphics
clock outputs
Each clock may be individually delayed for skew control
Video output clock may be directly connected to
Gennum’s serializers for a SMPTE-compliant HD-SDI
output
Audio Clock Synthesis (GS4911B only)
•
•
•
Three audio clock outputs
Generates any audio clock up to 512*96kHz
Pre-programmed for 7 audio clocks
Timing Generation
•
•
•
Generates up to 8 timing signals at a time
Choose from 9 pre-programmed timing signals: H and V
sync and blanking, F Sync, F Digital, AFS (GS4911B
only), Display Enable, 10FID, and up to 4 user-defined
timing signals
Pre-programmed to generate timing for 35 different video
formats and 13 different graphic display formats
Genlock Capability
•
•
•
•
•
•
Clocks may be free-running or genlocked to an input
reference with a variable offset step size of 100-200ps
(depending on exact clock frequency)
Variable timing offset step size of 100-200ps up to one
frame
Output may be cross-locked to a different input reference
Freeze operation on loss of reference
Optional crash or drift lock on application of reference
Automatic input format detection
General Features
•
•
•
•
•
Reduces design complexity and saves board space 9mm x 9mm package plus crystal reference replaces
multiple VCXOs, PLLs and timing generators
Pb-free and RoHS Compliant
Low power operation typically 300mW
1.8V core and 1.8V or 3.3V I/O power supplies
64-PIN QFN package
Applications
•
Video cameras; Digital audio and/or video recording/play
back devices; Digital audio and/or video processing
devices; Computer/video displays; DVD/MPEG devices;
Digital Set top boxes; Video projectors; High definition
video systems; Multi-media PC applications
The GS4910B includes all the features of the GS4911B,
but does not offer audio clocks or AFS pulse generation.
The GS4911B/GS4910B will recognize input reference
signals conforming to 36 different video standards and
16 different graphic formats, and will genlock the output
timing information to the incoming reference. The
GS4911B/GS4910B supports cross-locking, allowing
the output to be genlocked to an incoming reference
that is different from the output video standard selected.
The user may select to output one of 8 different video
sample clock rates or 13 different graphic display clock
rates, or may program any clock frequency between
13.5MHz and 165MHz. The chosen clock frequency
can be further divided using internal dividers, and is
available on two video clock outputs and one LVDS
video clock output pair. The video clocks are frequency
and phased-locked to the horizontal timing reference,
and can be individually delayed with respect to the
timing outputs for clock skew control.
Eight user-selectable timing outputs are provided that
can automatically produce the following timing signals
for 35 different video formats and 13 different graphics
formats: HSync, Hblanking, VSync, Vblanking, F sync,
F digital, AFS (GS4911B only), DE, and 10FID. These
timing outputs may be locked to the input reference
signal for genlock timing and may be phase adjusted via
internal registers.
In addition, the GS4911B provides three audio sample
clock outputs that can produce audio clocks up to 512fs
with fs ranging from 9.7kHz to 96kHz. Audio to video
phasing is accomplished by an external 10FID input
reference, a 10FID signal specified via internal
registers, or a user-programmed audio frame
sequence.
The GS4911B/GS4910B is Pb-free, and the
encapsulation compound does not contain halogenated
flame retardant (RoHS Compliant).
36655 - 2
April 2006
1 of 113
www.gennum.com
LOCK_LOST
VID_STD[5:0]
GENLOCK
ASR_SEL[2:0]
X1
X2
GS4911B/GS4910B Data Sheet
user[4:1]
27MHz
Input Reference
Rate Identification
and Control
ref_rate
REF_LOST
Flywheel and Video
Timing Generator
AFS
10FID
DE
F digital
F sync
V blanking
V sync
TIMING_OUT_8
TIMING_OUT_7
TIMING_OUT_6
Crosspoint
TIMING_OUT_4
TIMING_OUT_3
TIMING_OUT_2
H blanking
H sync
Clock Synthesis
and Control
TIMING_OUT_5
TIMING_OUT_1
PCLK1
Clock
Phase
Adjust
pclk
Video Clock
Divide
3x Video Clock
Delay Adjust
PCLK2
PCLK3
PCLK3
aclk_512
aclk_384
Audio Clock
Divide
ACLK1
ACLK2
ACLK3
HSYNC
VSYNC
FSYNC
10FID
CS_TMS
SDIN_TDI
SDOUT_TDO
SCLK_TCLK
JTAG/HOST
Application Programming Interace
GS4911B Functional Block Diagram
36655 - 2
April 2006
2 of 113
LOCK_LOST
VID_STD[5:0]
GENLOCK
X1
X2
GS4911B/GS4910B Data Sheet
user[4:1]
27MHz
Input Reference
Rate Identification
and Control
ref_rate
REF_LOST
Flywheel and Video
Timing Generator
10FID
DE
F digital
F sync
V blanking
V sync
TIMING_OUT_8
TIMING_OUT_7
TIMING_OUT_6
Crosspoint
TIMING_OUT_5
TIMING_OUT_4
TIMING_OUT_3
H blanking
H sync
TIMING_OUT_2
TIMING_OUT_1
Clock Synthesis
and Control
PCLK1
Clock
Phase
Adjust
pclk
Video Clock
Divide
3x Video Clock
Delay Adjust
PCLK2
PCLK3
PCLK3
HSYNC
VSYNC
FSYNC
10FID
CS_TMS
SDIN_TDI
SDOUT_TDO
SCLK_TCLK
JTAG/HOST
Application Programming Interace
GS4910B Functional Block Diagram
36655 - 2
April 2006
3 of 113
GS4911B/GS4910B Data Sheet
Contents
Key Features .................................................................................................................1
Applications...................................................................................................................1
Description ....................................................................................................................1
1. Pin Out ......................................................................................................................8
1.1 GS4911B Pin Assignment ..............................................................................8
1.2 GS4910B Pin Assignment ..............................................................................9
1.3 Pin Descriptions ............................................................................................10
1.4 Pre-Programmed Recognized Video and Graphics Standards ....................20
1.5 Output Timing Signals ...................................................................................25
2. Electrical Characteristics .........................................................................................29
2.1 Absolute Maximum Ratings ..........................................................................29
2.2 DC Electrical Characteristics ........................................................................29
2.3 AC Electrical Characteristics .........................................................................31
2.4 Solder Reflow Profiles ...................................................................................35
3. Detailed Description ................................................................................................36
3.1 Functional Overview .....................................................................................36
3.2 Modes of Operation ......................................................................................36
3.2.1 Genlock Mode......................................................................................37
3.2.2 Free Run Mode....................................................................................40
3.3 Output Timing Format Selection ...................................................................42
3.4 Input Reference Signals ................................................................................43
3.4.1 HSYNC, VSYNC, and FSYNC.............................................................43
3.4.2 10FID ...................................................................................................44
3.4.3 Automatic Polarity Recognition ............................................................45
3.5 Reference Format Detector ..........................................................................45
3.5.1 Horizontal and Vertical Timing Characteristic Measurements .............45
3.5.2 Input Reference Validity.......................................................................45
3.5.3 Behaviour on Loss and Re-acquisition of the Reference Signal..........47
3.5.4 Allowable Frequency Drift on the Reference .......................................49
3.6 Genlock .........................................................................................................50
3.6.1 Automatic Locking Process .................................................................50
3.6.2 Manual Locking Process......................................................................54
3.6.3 Adjustable Locking Time......................................................................58
3.6.4 Adjustable Loop Bandwidth .................................................................58
3.6.5 Locking to Digital Timing from a Deserializer ......................................60
3.7 Clock Synthesis ............................................................................................61
3.7.1 Video Clock Synthesis .........................................................................61
3.7.2 Audio Clock Synthesis (GS4911B only) ..............................................63
3.8 Video Timing Generator ................................................................................67
3.8.1 10 Field ID Pulse .................................................................................67
36655 - 2
April 2006
4 of 113
GS4911B/GS4910B Data Sheet
3.8.2 Audio Frame Synchronizing Pulse (GS4911B only) ............................68
3.8.3 USER_1~4...........................................................................................69
3.8.4 TIMING_OUT Pins...............................................................................71
3.9 Custom Clock Generation .............................................................................72
3.9.1 Programming a Custom Video Clock...................................................72
3.9.2 Programming a Custom Audio Clock (GS4911B only) ........................73
3.10 Custom Output Timing Signal Generation ..................................................74
3.10.1 Custom Input Reference....................................................................74
3.11 Extended Audio Mode for HD Demux using the Gennum Audio Core .......75
3.12 GSPI Host Interface ....................................................................................76
3.12.1 Command Word Description..............................................................77
3.12.2 Data Read and Write Timing .............................................................77
3.12.3 Configuration and Status Registers ...................................................79
3.13 JTAG .........................................................................................................105
3.14 Device Power-Up ......................................................................................106
3.14.1 Power Supply Sequencing...............................................................106
3.15 Device Reset .............................................................................................106
4. Application Reference Design ...............................................................................107
4.1 GS4911B Typical Application Circuit ..........................................................107
4.2 GS4910B Typical Application Circuit ..........................................................108
5. References & Relevant Standards ........................................................................109
6. Package & Ordering Information ...........................................................................110
6.1 Package Dimensions ..................................................................................110
6.2 Recommended PCB Footprint ....................................................................111
6.3 Packaging Data ...........................................................................................111
6.4 Ordering Information ...................................................................................112
7. Revision History ....................................................................................................113
36655 - 2
April 2006
5 of 113
GS4911B/GS4910B Data Sheet
List of Figures
GS4911B Functional Block Diagram........................................................................... 2
GS4910B Functional Block Diagram........................................................................... 3
Figure 1-1: XTAL1 and XTAL2 Reference Circuits ....................................................19
Figure 2-1: PCLK to TIMING_OUT Signal Output Timing ..........................................34
Figure 2-2: Maximum Pb-free Solder Reflow Profile (preferred) ................................35
Figure 2-3: Standard Pb Solder Reflow Profile .........................................................35
Figure 3-1: HD-SD Calculation ...................................................................................39
Figure 3-2: Output Accuracy and Modes of Operation ...............................................41
Figure 3-3: Example HSYNC, VSYNC, and FSYNC Analog Input Timing
from a Sync Separator ...............................................................................................43
Figure 3-4: Example H Blanking, V Blanking, and F Digital Input Timing
from an SDI Deserializer ............................................................................................43
Figure 3-5: 10FID Input Timing ..................................................................................44
Figure 3-6: Internal Video Genlock Block ...................................................................54
Figure 3-7: Internal Audio Genlock Block ...................................................................56
Figure 3-8: Default 10FID Output Timing ...................................................................67
Figure 3-9: Optional 10FID Output Timing .................................................................68
Figure 3-10: AFS Output Timing ................................................................................69
Figure 3-11: USER Programmable Output Signal .....................................................70
Figure 3-12: Custom Timing Parameters ...................................................................74
Figure 3-13: Audio Clock Block Diagram for HD Demux Operation ...........................75
Figure 3-14: GSPI Application Interface Connection .................................................76
Figure 3-15: Command Word Format ........................................................................77
Figure 3-16: Data Word Format .................................................................................77
Figure 3-17: GSPI Read Mode Timing .......................................................................78
Figure 3-18: GSPI Write Mode Timing .......................................................................78
Figure 3-19: In-Circuit JTAG ....................................................................................105
Figure 3-20: System JTAG .......................................................................................106
36655 - 2
April 2006
6 of 113
GS4911B/GS4910B Data Sheet
List of Tables
Table 1-1: Pin Descriptions ........................................................................................ 10
Table 1-2: Recognized Video and Graphics Standards ............................................. 21
Table 1-3: Output Timing Signals............................................................................... 25
Table 2-1: DC Electrical Characteristics .................................................................... 29
Table 2-2: AC Electrical Characteristics..................................................................... 31
Table 2-3: Suggested External Crystal Specification ................................................. 34
Table 3-1: Clock_Phase_Offset[15:0] Encoding Scheme .......................................... 38
Table 3-2: Ambiguous Standard Identification ........................................................... 47
Table 3-3: Max_Ref_Delta Encoding Scheme ........................................................... 49
Table 3-4: Cross-reference Genlock Table ................................................................ 52
Table 3-5: Integer Constant Value ............................................................................. 57
Table 3-6: Video Clock Phase Adjustment Host Settings .......................................... 62
Table 3-7: Audio Sample Rate Select ........................................................................ 63
Table 3-8: Audio Clock Divider................................................................................... 64
Table 3-9: Encoding Scheme for AFS_Reset_Window ............................................. 65
Table 3-10: Audio Sampling Frequency to Video Frame Rate Synchronization ........ 66
Table 3-11: Crosspoint Select .................................................................................... 71
Table 3-12: GSPI Timing Parameters ........................................................................ 78
Table 3-13: Configuration and Status Registers ........................................................ 79
Table 5-1: References & Relevant Standards.......................................................... 109
36655 - 2
April 2006
7 of 113
GS4911B/GS4910B Data Sheet
1. Pin Out
LOCK_LOST
REF_LOST
1
PCLK2
PCLK1
IO_VDD
PCLK1&2_VDD
PCLK1&2_GND
PhS_VDD
JTAG/HOST
PhS_GND
SDIN_TDI
SCLK_TCLK
SDOUT_TDO
RESET
CS_TMS
IO_VDD
GENLOCK
NC
1.1 GS4911B Pin Assignment
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
LVDS/PCLK3_GND
2
47
PCLK3
VID_PLL_VDD
3
46
PCLK3
VID_PLL_GND
4
45
LVDS/PCLK3_VDD
XTAL_VDD
5
44
X1
6
43
CORE_VDD
TIMING_OUT_8
X2
7
42
TIMING_OUT_7
41
40
TIMING_OUT_6
TIMING_OUT_5
XTAL_GND
8
CORE_GND
9
GS4911B
64-pin QFN
(Top View)
ANALOG_VDD
NC
10
39
TIMING_OUT_4
11
38
IO_VDD
ANALOG_GND
12
37
TIMING_OUT_3
AUD_PLL_GND
13
36
TIMING_OUT_2
AUD_PLL_VDD
14
35
TIMING_OUT_1
10FID
HSYNC
34
15
16
33
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
ASR_SEL0
ASR_SEL1
ASR_SEL2
IO_VDD
ACLK3
ACLK2
ACLK1
VID_STD5
VID_STD4
CORE_VDD
VID_STD3
VID_STD2
VID_STD1
VID_STD0
NC
FSYNC
IO_VDD
VSYNC
Ground Pad
(bottom of package)
36655 - 2
April 2006
8 of 113
GS4911B/GS4910B Data Sheet
LOCK_LOST
REF_LOST
1
PCLK2
PCLK1
IO_VDD
PCLK1&2_GND
PhS_VDD
PCLK1&2_VDD
JTAG/HOST
PhS_GND
SDIN_TDI
SCLK_TCLK
SDOUT_TDO
CS_TMS
RESET
IO_VDD
GENLOCK
NC
1.2 GS4910B Pin Assignment
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
LVDS/PCLK3_GND
2
47
PCLK3
VID_PLL_VDD
3
46
PCLK3
VID_PLL_GND
4
45
LVDS/PCLK3_VDD
XTAL_VDD
5
44
X1
6
43
CORE_VDD
TIMING_OUT_8
X2
7
42
TIMING_OUT_7
41
40
TIMING_OUT_6
TIMING_OUT_5
XTAL_GND
8
CORE_GND
9
GS4910B
64-pin QFN
(Top View)
ANALOG_VDD
NC
10
39
TIMING_OUT_4
11
38
IO_VDD
ANALOG_GND
12
37
TIMING_OUT_3
ANALOG_GND
ANALOG_GND
10FID
13
36
TIMING_OUT_2
14
35
TIMING_OUT_1
34
15
16
33
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
ANALOG_GND
HSYNC
ANALOG_GND
ANALOG_GND
IO_VDD
NC
NC
NC
VID_STD5
CORE_VDD
VID_STD4
VID_STD3
VID_STD2
VID_STD1
VID_STD0
NC
FSYNC
VSYNC
IO_VDD
Ground Pad
(bottom of package)
36655 - 2
April 2006
9 of 113
GS4911B/GS4910B Data Sheet
1.3 Pin Descriptions
Table 1-1: Pin Descriptions
Pin
Number
1
Name
Timing
Type
Description
LOCK_LOST
Non
Synchronous
Output
STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
This pin will be HIGH if the output is not genlocked to the input.
The GS4911B/GS4910B monitors the output pixel/line counters, as well
as the internal lock status from the genlock block and asserts
LOCK_LOST HIGH if it is determined that the output is not genlocked to
the input. This pin will be LOW if the device successfully genlocks the
output clock and timing signals to the input reference.
If LOCK_LOST is LOW, the reference timing generator outputs will be
phase locked to the detected reference signal, producing an output in
accordance with the video standard selected by the VID_STD[5:0] pins.
2
REF_LOST
Non
Synchronous
Output
STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
This pin will be HIGH if:
• No input reference signal is applied to the device; or
• The input reference applied does not meet the minimum/maximum
timing requirements described in Section 3.5.2 on page 45.
This pin will be LOW otherwise.
If the reference signal is removed when the device is in Genlock mode,
REF_LOST will go HIGH and the GS4911B/GS4910B will enter Freeze
mode (see Section 3.2.1.2 on page 40).
3
VID_PLL_VDD
–
Power
Supply
Most positive power supply connection for the video clock synthesis
internal block. Connect to +1.8V DC.
4
VID_PLL_GND
–
Power
Supply
Ground connection for the video clock synthesis internal block. Connect
to GND.
5
XTAL_VDD
–
Power
Supply
Most positive power supply connection for the crystal buffer. Connect to
either +1.8V DC or +3.3V DC.
NOTE: Connect to +3.3V for minimum output PCLK jitter.
6
7
X1
X2
Non
Synchronous
Input
Non
Synchronous
Output
ANALOG SIGNAL INPUT
Connect to a 27MHz crystal or a 27MHz external clock source. See
Figure 1-1.
ANALOG SIGNAL OUTPUT
Connect to a 27MHz crystal, or leave this pin open circuit if an external
clock source is applied to pin 6. See Figure 1-1.
8
XTAL_GND
–
Power
Supply
Ground connection for the crystal buffer. Connect to GND.
9
CORE_GND
–
Power
Supply
Ground connection for core and I/O. Solder to the ground plane of the
application board.
NOTE: The CORE_GND pin should be soldered to the same main
ground plane as the exposed ground pad on the bottom of the device.
10
11, 20, 63
ANALOG_VDD
–
Power
Supply
Most positive power supply connection for the analog input block.
Connect to +1.8V DC.
NC
–
–
Do not connect.
36655 - 2
April 2006
10 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
Name
Timing
Type
Description
12
ANALOG_GND
–
Power
Supply
Ground connection for the analog input block. Connect to GND.
13
AUD_PLL_GND
(GS4911B only)
–
Power
Supply
Ground connection for the audio clock synthesis internal block. Connect
to GND.
ANALOG_GND
(GS4910B only)
–
Power
Supply
Ground connection for the analog input block. Connect to GND.
AUD_PLL_VDD
(GS4911B only)
–
Power
Supply
Most positive power supply connection for the audio clock synthesis
internal block. Connect to +1.8V DC.
ANALOG_GND
(GS4910B only)
–
Power
Supply
Ground connection for the analog input block. Connect to GND.
10FID
Non
Synchronous
Input
REFERENCE SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
14
15
The 10FID external reference signal is applied to this pin by the
application layer. 10FID defines the field in which the video and audio
clock phase relationship is defined according to SMPTE 318-M. It is also
used to define a 3:2 video cadence.
NOTE: If the input reference format does not include a 10 Field ID signal,
this pin should be held LOW. See Section 3.4.2 on page 44.
16
HSYNC
Non
Synchronous
Input
REFERENCE SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
The HSYNC external reference signal is applied to this pin by the
application layer. When the GS4911B/GS4910B is operating in Genlock
mode, the device senses the polarity of the HSYNC input automatically,
and references to the leading edge.
If the user wishes to select one of the pre-programmed video and/or
timing output signals provided by the device, then this signal must
adhere to one of the 36 defined video or 16 different graphics display
standards supported by the device. In this mode of operation, the
HSYNC input provides a horizontal scanning reference signal.
The HSYNC signal may have analog timing, such as from a sync
separator, or may be digital such as from an SDI deserializer. Section 1.4
on page 20 describes the 36 video formats and 16 graphic formats
recognized by the GS4911B/GS4910B.
17
VSYNC
Non
Synchronous
Input
REFERENCE SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
The VSYNC external reference signal is applied to this pin by the
application layer. When the GS4911B/GS4910B is operating in Genlock
mode, the device senses the polarity of the VSYNC input automatically,
and references to the leading edge.
If the user wishes to select one of the pre-programmed video and/or
timing output signals provided by the device, then this signal must
adhere to one of the 36 defined video or 16 different graphics display
standards supported by the device. In this mode of operation, the
VSYNC input provides a vertical scanning reference signal.
The VSYNC signal may have analog timing, such as from a sync
separator, or may be digital such as from an SDI deserializer. Section 1.4
on page 20 describes the 36 video formats and 16 graphic formats
recognized by the GS4911B/GS4910B.
36655 - 2
April 2006
11 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
18, 31, 38,
50, 62
Name
Timing
Type
Description
IO_VDD
–
Power
Supply
Most positive power supply connection for the digital I/O signals.
Connect to either +1.8V DC or +3.3V DC.
NOTE: All five IO_VDD pins must be powered by the same voltage.
19
FSYNC
Non
Synchronous
Input
REFERENCE SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
The FSYNC external reference signal is applied to this pin by the
application layer.
The first field is defined as the field in which the first broad pulse (also
known as serration) is in the first half of a line. The FSYNC signal should
be set HIGH during the first field for sync-based references.
If the user wishes to select one of the pre-programmed video and/or
timing output signals provided by the device, then this signal must
adhere to one of the 36 defined video or 16 different graphics display
standards supported by the device. In this mode of operation, the
FSYNC input provides an odd/even field input reference.
The FSYNC signal may have analog timing, such as from a sync
separator, or may be digital such as from an SDI deserializer. Section 1.4
on page 20 describes the 36 video formats and 16 graphic formats
recognized by the GS4911B/GS4910B.
For blanking-based references, the FSYNC signal should be set HIGH
during the second field.
NOTE: If the input reference format does not include an F sync signal,
this pin should be held LOW.
27, 25, 24,
23, 22, 21
VID_STD[5:0]
Non
Synchronous
Input
CONTROL SIGNAL INPUTS
Signal levels are LVCMOS/LVTTL compatible.
Video Standard Select.
Used to select the desired video/graphic display format for video clock
and timing signal generation.
8 different video and 13 different graphic sample clocks, as well as 35
different video format and 13 different graphic format timing signal
outputs may be selected using these pins.
For details on the supported video standards and video clock frequency
selection, please see Section 1.4 on page 20.
26, 44
CORE_VDD
–
36655 - 2
Power
Supply
April 2006
Most positive power supply connection for the digital core. Connect to
+1.8V DC.
12 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
28, 29, 30
Name
Timing
Type
Description
ACLK1
–
Output
ACLK2
CLOCK SIGNAL OUTPUTS
Signal levels are LVCMOS/LVTTL compatible.
ACLK3
Audio output clock signals.
(GS4911B only)
ACLK1, ACLK2, and ACLK3 present audio sample rate clock outputs to
the application layer.
By default, after system reset, the audio clock output pins of the device
provide clock signals as follows:
ACLK1 = 256fs
ACLK2 = 64fs
ACLK3 = fs, where fs is the fundamental sampling frequency.
The fundamental sampling frequency is selected using ASR_SEL[2:0].
Additional sampling frequencies may be programmed in the host
interface.
It is also possible to select different division ratios for each of the audio
clock outputs by programming designated registers in the host interface.
Clock outputs of 512fs, 384fs, 256fs, 192fs, 128fs, 64fs, fs and z bit are
selectable on a pin-by-pin basis.
NOTE: ACLK1-3 will have a 50% duty cycle, unless fs is selected as
96kHz and the host interface is configured such that one of the three
ACLK pins is set to output a clock signal at 192fs or 384fs. If this is the
case, then a 512fs clock will have a 33% duty cycle.
These signals will be high impedance when ASR_SEL[2:0] = 000b.
32, 33, 34
NC
(GS4910B only)
–
–
Do not connect.
ASR_SEL[2:0]
Non
Synchronous
Input
CONTROL SIGNAL INPUTS
Signal levels are LVCMOS/LVTTL compatible.
(GS4911B only)
Audio Sample Rate Select.
Used to select the fundamental sampling frequency, fs, of the audio clock
outputs. See Table 3-7.
When ASR_SEL[2:0] = 000b, audio clock generation will be disabled and
the ACLK1 to ACLK3 pins will be high impedance. In this case,
AUD_PLL_VDD (pin 14) may be connected to GND to minimize noise
and power consumption.
35
ANALOG_GND
(GS4910B only)
–
Power
Supply
Ground connection for the analog input block. Connect to GND.
TIMING_OUT_1
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is H Sync.
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
36655 - 2
April 2006
13 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
36
Name
Timing
Type
Description
TIMING_OUT_2
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is H blanking.
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
37
TIMING_OUT_3
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is V Sync.
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
39
TIMING_OUT_4
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is V blanking.
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
40
TIMING_OUT_5
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is F Sync.
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
36655 - 2
April 2006
14 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
41
Name
Timing
Type
Description
TIMING_OUT_6
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is F digital.
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
42
TIMING_OUT_7
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is 10 Field ID (10FID).
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
43
TIMING_OUT_8
Synchronous
with PCLK1 ~
PCLK3
Output
TIMING SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Selectable timing output.
Selectable from: H sync; H blanking; V sync; V blanking; F sync; F
digital; Display Enable; 10 field ID (film cadence); AFS video/audio timing
(GS4911B only); USER_1~4.
See Section 1.5 on page 25 for signal descriptions.
NOTE: Default output is Display Enable (DE).
The current drive capability of this pin may be set high or low via
designated registers in the host interface. By default, the current drive
will be low.
This signal will be high impedance when VID_STD[5:0] = 00h.
45
LVDS/PCLK3_VDD
–
36655 - 2
Power
Supply
April 2006
Most positive power supply connection for PCLK3 output circuitry and
LVDS driver. Connect to +1.8V DC.
15 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
46, 47
Name
Timing
Type
Description
PCLK3, PCLK3
–
Output
CLOCK SIGNAL OUTPUTS
Signal levels are LVDS compatible.
Differential video clock output signal.
PCLK3/PCLK3 present a differential video sample rate clock output to
the application layer.
By default, after system reset, this output will operate at the fundamental
frequency determined by the setting of the VID_STD[5:0] pins. It is
possible to define other non-standard fundamental clock rates using the
host interface.
It is also possible to select different division ratios for the
PCLK3/PCLK3 outputs by programming designated registers in the
host interface. A clock output of the fundamental rate, fundamental rate
÷2, or fundamental rate ÷4 may be selected.
The PCLK3/PCLK3 outputs will be high impedance when
VID_STD[5:0] = 00h.
48
LVDS/PCLK3_GND
–
Power
Supply
Ground connection for PCLK3 output circuitry and LVDS driver. Connect
to GND.
49
PCLK2
–
Output
CLOCK SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Video clock output signal.
PCLK2 presents a video sample rate clock output to the application
layer.
By default, after system reset, the PCLK2 output pin will operate at the
fundamental frequency determined by the setting of the VID_STD[5:0]
pins. It is possible to define other non-standard fundamental clock rates
using the host interface.
It is also possible to select different division ratios for the PCLK2 output
by programming designated registers in the host interface. A clock
output of the fundamental rate, fundamental rate ÷2, or fundamental rate
÷4 may be selected.
By setting designated registers in the host interface, the current drive
capability of this pin may be set high or low. By default, the current drive
will be low. It must be set high if the clock rate is greater than 100MHz.
The PCLK2 output will be held LOW when VID_STD[5:0] = 00h.
36655 - 2
April 2006
16 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
51
Name
Timing
Type
Description
PCLK1
–
Output
CLOCK SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Video clock output signal.
PCLK1 presents a video sample rate clock output to the application
layer.
By default, after system reset, the PCLK1 output pin will operate at the
fundamental frequency determined by the setting of the VID_STD[5:0]
pins. It is possible to define other non-standard fundamental clock rates
using the host interface.
It is also possible to select different division ratios for the PCLK1 output
by programming designated registers in the host interface. A clock
output of the fundamental rate, fundamental rate ÷2, or fundamental rate
÷4 may be selected.
By setting designated registers in the host interface, the current drive
capability of this pin may be set high or low. By default, the current drive
will be low. It must be set high if the clock rate is greater than 100MHz.
The PCLK1 output will be held LOW when VID_STD[5:0] = 00h.
52
PCLK1&2_GND
–
Power
Supply
Ground connection for PCLK1&2 circuitry. Connect to GND.
53
PCLK1&2_VDD
–
Power
Supply
Most positive power supply connection for PCLK1&2 circuitry. Connect to
+1.8V DC.
54
PhS_VDD
–
Power
Supply
Most positive power supply connection for the video clock phase shift
internal block. Connect to +1.8V DC.
55
PhS_GND
–
Power
Supply
Ground connection for the video clock phase shift internal block. Connect
to GND.
56
JTAG/HOST
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to select JTAG Test Mode or Host Interface Mode.
When set HIGH, CS_TMS, SCLK_TCLK, SDOUT_TDO, and SDIN_TDI
are configured for JTAG boundary scan testing.
When set LOW, CS_TMS, SCLK_TCLK, SDOUT_TDO, and SDIN_TDI
are configured as GSPI pins for normal host interface operation.
57
SCLK_TCLK
Non
Synchronous
Input
SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Serial Data Clock / Test Clock.
All JTAG / Host Interface address and data are shifted into/out of the
device synchronously with this clock.
Host Mode (JTAG/HOST = LOW):
SCLK_TCLK operates as the host interface serial data clock, SCLK.
JTAG Test Mode (JTAG/HOST = HIGH):
SCLK_TCLK operates as the JTAG test clock, TCLK.
36655 - 2
April 2006
17 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
58
Name
Timing
Type
Description
SDIN_TDI
Synchronous
with
SCLK_TCLK
Input
SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Serial Data Input / Test Data Input.
Host Mode (JTAG/HOST = LOW):
SDIN_TDI operates as the host interface serial input, SDIN, used to write
address and configuration information to the internal registers of the
device.
JTAG Test Mode (JTAG/HOST = HIGH):
SDIN_TDI operates as the JTAG test data input, TDI.
59
SDOUT_TDO
Synchronous
with
SCLK_TCLK
Output
SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Serial Data Output / Test Data Output.
Host Mode (JTAG/HOST = LOW):
SDOUT_TDO operates as the host interface serial output, SDOUT, used
to read status and configuration information from the internal registers of
the device.
JTAG Test Mode (JTAG/HOST = HIGH):
SDOUT_TDO operates as the JTAG test data output, TDO.
60
CS_TMS
Synchronous
with
SCLK_TCLK
Input
SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Chip Select / Test Mode Select.
Host Mode (JTAG/HOST = LOW):
CS_TMS operates as the host interface chip select, CS, and is active
LOW.
JTAG Test Mode (JTAG/HOST = HIGH):
CS_TMS operates as the JTAG test mode select, TMS, and is active
HIGH.
61
RESET
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to reset the internal operating conditions to their default settings or
to reset the JTAG test sequence.
Host Mode (JTAG/HOST = LOW):
When asserted LOW, all host registers and functional blocks will be set
to their default conditions. All input and output signals will become high
impedance, except PCLK1 and PCLK2, which will be set LOW.
When set HIGH, normal operation of the device will resume.
The user must hold this pin LOW during power-up and for a minimum of
500 uS after the last supply has reached its operating voltage.
JTAG Test Mode (JTAG/HOST = HIGH):
When asserted LOW, all host registers and functional blocks will be set
to their default conditions and the JTAG test sequence will be held in
reset.
When set HIGH, normal operation of the JTAG test sequence will
resume.
36655 - 2
April 2006
18 of 113
GS4911B/GS4910B Data Sheet
Table 1-1: Pin Descriptions (Continued)
Pin
Number
64
Name
Timing
Type
Description
GENLOCK
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Selects Genlock mode or Free Run mode.
When this pin is set LOW and the device has successfully genlocked the
output to the input reference, the device will enter Genlock mode. The
video clock and timing outputs will be frequency and phase locked to the
detected reference signal.
When this pin is set HIGH, the video clock and the reference-timing
generator will free-run.
By default, the GS4911B’s audio clocks will be genlocked to the output
video clock regardless of the setting of this pin.
NOTE: The user must apply a reference to the input of the device prior to
setting GENLOCK = LOW. If the GENLOCK pin is set LOW and no
reference signal is present, the generated clock and timing outputs of the
device may correspond to the internal default settings of the chip until a
reference is applied.
–
Ground Pad
–
–
Ground pad on bottom of package must be soldered to main ground
plane of PCB.
External Crystal Connection
External Clock Source Connection
38pF
6 X1
6 X1
external
clock
1M
7 X2
7 X2
NC
24pF
Notes:
1. Capacitor values listed represent the total capacitance,
including discrete capacitance and parasitic board capacitance.
2. X1 serves as an input, which may alternatively accept a 27MHz clock
source. To accomodate this, mismatched capacitor values are recommended.
Figure 1-1: XTAL1 and XTAL2 Reference Circuits
36655 - 2
April 2006
19 of 113
GS4911B/GS4910B Data Sheet
1.4 Pre-Programmed Recognized Video and Graphics Standards
Table 1-2 describes the video and graphics standards automatically recognized by
the GS4911B/GS4910B. Any one of the 36 different video formats and 16 different
graphic display formats listed below can be applied to the GS4911B/GS4910B and
automatically detected by the reference format detector. Moreover, each format,
with the exception of VID_STD[5:0] = 2, 52, 53, or 54, is available for output on the
timing output pins by setting the VID_STD[5:0] pins.
In addition to the pre-programmed video standards listed in Table 1-2, custom
output timing signals may be generated by the GS4911B/GS4910B. The custom
timing parameters are programmed in the host interface when VID_STD[5:0] is set
to 62 (see Section 3.10 on page 74).
Setting VID_STD[5:0] to 63 will cause the device to produce an output format with
identical timing to the detected input reference.
If desired, the external VID_STD[5:0] pins may be ignored by setting bit 1 of the
Video_Control register, and the video standard may instead be selected via the
VID_STD[5:0] register of the host interface (see Section 3.12.3 on page 79).
Although the external VID_STD[5:0] pins will be ignored in this case, they should
not be left floating.
36655 - 2
April 2006
20 of 113
PCLK1&2 =LOW.
PCLK3/PCLK3 = High
Impedance
4fsc 525 / 2:1
interlace
Composite PAL 625
/ 2:1 interlace / 25
601 525 / 2:1 interlace
601 625 / 2:1 interlace
601 – 18MHz 525
/ 2:1 interlace
601 – 18 MHz 625
/ 2:1 interlace
720x486/59.94/2:1
interlace
720x576/50/2:1
interlace
720x483/59.94/1:1
progressive
720x576/50/1:1
progressive
1280x720/60/1:1
progressive
1280x720/59.94/1:1
progressive
1280/720/50/1:1
progressive
1
2*
3
4‡
5
6‡
7
8‡
9
10
11
12
13
System
Nomenclature
0
VID_STD
[5:0]
1980
April 2006
36655 - 2
1650
1650
1728
1716
3456
3432
2304
2288
1728
1716
–
74.25
74.175
74.25
54
54
54
54
36
36
27
27
–
910
–
–
14.32
PCLKS
/ Total
Line
Video PCLK
Frequency
(MHz)
Table 1-2: Recognized Video and Graphics Standards
750
750
750
625
525
625
525
625
525
625
525
625
525
–
Total Lines
/ Frame
1280
1280
1280
1440
1440
2880
2880
1920
1920
1440
1440
–
768
–
PCLKS
/ Active
Line
80
80
80
127
127
252
252
169
169
127
127
–
67
–
H Sync
Width
(Clocks)
tri
tri
tri
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
–
H Sync
Polarity
5
5
5
5
6
2.5
3
2.5
3
2.5
3
2.5
3
–
V Sync
Width
(Lines)
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
–
V Sync
Polarity
720
720
720
576
483
576
486
576
486
576
486
576
486
–
Active
Lines /
Frame
21 of 113
SMPTE 296M
SMPTE 296M
SMPTE 296M
ITU-R BT.1358
/ SMPTE 347M
SMPTE 293M
/ SMPTE 347M
ITU-R BT.799
/ SMPTE 347M
SMPTE RP174
/ SMPTE 347M
ITU-R BT.601-5
SMPTE 267M
ITU-R BT.601-5
SMPTE
125M/267M
–
SMPTE 244M
–
Scan
Format
Standard
GS4911B/GS4910B Data Sheet
System
Nomenclature
1280x720/30/1:1
progressive
1280x720/29.97/1:1
progressive
1280x720/25/1:1
progressive
1280x720/24/1:1
progressive
1280x720/23.98/1:1
progressive
1920x1035/60/2:1
interlace
1920x1035/59.94/2:1
interlace
1920x1080/60/1:1
progressive
1920x1080/59.94/1:1
progressive
1920x1080/50/1:1
progressive
Reserved
1920x1080/60/2:1
interlace
1920x1080/59.94/2:1
interlace
1920x1080/50/2:1
interlace
Reserved
VID_STD
[5:0]
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
36655 - 2
–
74.25
74.175
74.25
–
148.5
148.35
148.5
74.175
74.25
74.175
74.25
74.25
74.175
74.25
–
2640
2200
2200
–
2640
2200
2200
2200
2200
4125
4125
3960
3300
3300
PCLKS
/ Total
Line
April 2006
Video PCLK
Frequency
(MHz)
–
1125
1125
1125
–
1125
1125
1125
1125
1125
750
750
750
750
750
Total Lines
/ Frame
Table 1-2: Recognized Video and Graphics Standards (Continued)
–
1920
1920
1920
–
1920
1920
1920
1920
1920
1280
1280
1280
1280
1280
PCLKS
/ Active
Line
–
80
80
80
–
80
80
80
80
80
80
80
80
80
80
H Sync
Width
(Clocks)
–
tri
tri
tri
–
tri
tri
tri
tri
tri
tri
tri
tri
tri
tri
H Sync
Polarity
–
5
5
5
–
5
5
5
5
5
5
5
5
5
5
V Sync
Width
(Lines)
–
negative
negative
negative
–
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
V Sync
Polarity
–
1080
1080
1080
–
1080
1080
1080
1035
1035
720
720
720
720
720
Active
Lines /
Frame
22 of 113
–
SMPTE 274M
SMPTE 274M
SMPTE 274M
–
SMPTE 274M
SMPTE 274M
SMPTE 274M
SMPTE 260M
SMPTE 260M
SMPTE 296M
SMPTE 296M
SMPTE 296M
SMPTE 296M
SMPTE 296M
Scan
Format
Standard
GS4911B/GS4910B Data Sheet
System
Nomenclature
1920x1080/30/1:1
progressive
1920x1080/30/PsF
1920x1080/29.97/1:1
progressive
1920x1080/29.97/PsF
1920x1080/25/1:1
progressive
1920x1080/25/PsF
1920x1080/24/1:1
progressive
1920x1080/24/PsF
1920x1080/23.98/1:1
progressive
1920x1080/23.98/PsF
640 x 480 VGA
@ 60 Hz
640 x 480 VGA
@ 75 Hz
640 x 480 VGA
@ 85 Hz
800 x 600 SVGA
@ 60 Hz
800 x 600 SVGA
@ 75 Hz
800 x 600 SVGA
@ 85 Hz
1024 x 768 XGA
@ 60 Hz
VID_STD
[5:0]
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
36655 - 2
65
56.25
49.5
40.00
36
31.5
25.2
74.175
74.175
74.25
74.25
74.25
74.25
74.175
74.175
74.25
74.25
1344
1048
1056
1056
832
840
800
2750
2750
2750
2750
2640
2640
2200
2200
2200
2200
PCLKS
/ Total
Line
April 2006
Video PCLK
Frequency
(MHz)
806
631
625
628
509
500
525
1125
1125
1125
1125
1125
1125
1125
1125
1125
1125
Total Lines
/ Frame
Table 1-2: Recognized Video and Graphics Standards (Continued)
1024
800
800
800
640
640
640
1920
1920
1920
1920
1920
1920
1920
1920
1920
1920
PCLKS
/ Active
Line
136
64
80
128
56
64
96
80
80
80
80
80
80
80
80
80
80
H Sync
Width
(Clocks)
negative
positive
positive
positive
negative
negative
negative
tri
tri
tri
tri
tri
tri
tri
tri
tri
tri
H Sync
Polarity
6
3
3
4
3
3
2
5
5
5
5
5
5
5
5
5
5
V Sync
Width
(Lines)
negative
positive
positive
positive
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
negative
V Sync
Polarity
768
600
600
600
480
480
480
1080
1080
1080
1080
1080
1080
1080
1080
1080
1080
Active
Lines /
Frame
23 of 113
VESA
VG901101A
VESA
VDMTPROP
VESA
VDMT75HZ
VESA
VG900602
VESA
VDMTPROP
VESA
VDMT75HZ
IBM Standard
SMPTE RP 211
SMPTE 274M
SMPTE RP 211
SMPTE 274M
SMPTE RP 211
SMPTE 274M
SMPTE RP 211
SMPTE 274M
SMPTE RP 211
SMPTE 274M
Scan
Format
Standard
GS4911B/GS4910B Data Sheet
1024 x 768 XGA
@ 85 Hz
1280 x 1024 SXGA
@ 60 Hz
1280 x 1024 SXGA
@ 75 Hz
1280 x 1024 SXGA
@ 85 Hz
1600 x 1200 UXGA
@ 60 Hz
1600 x 1200 UXGA
@ 75 Hz
1600 x 1200 UXGA
@ 85 Hz
2048 x 1536 QXGA
@ 60 Hz
47
48
49
50
51†
52*
53*
54*
Automatic Output
Standard follows Input
Standard
63
–
–
–
–
–
–
–
–
–
–
–
–
2160
1728
157.5
162
1688
1688
1376
1312
PCLKS
/ Total
Line
135.00
108.00
94.5
78.75
Video PCLK
Frequency
(MHz)
–
–
–
1589
1250
1250
1250
1072
1066
1066
808
800
Total Lines
/ Frame
–
–
–
–
–
–
1600
1280
1280
1280
1024
1024
PCLKS
/ Active
Line
–
–
–
–
–
–
192
160
144
112
96
96
H Sync
Width
(Clocks)
–
–
–
negative
negative
negative
negative
negative
negative
positive
negative
positive
H Sync
Polarity
–
–
–
3
3
3
3
3
3
3
3
3
V Sync
Width
(Lines)
–
–
–
positive
positive
positive
positive
positive
positive
positive
positive
positive
V Sync
Polarity
–
–
–
1536
1200
1200
1200
1024
1024
1024
768
768
Active
Lines /
Frame
–
–
–
–
–
–
VESA
VDMTPROP
VESA
VDMTPROP
VESA
VDMT75HZ
VESA
VDMTREV
VESA
VDMTPROP
VESA
VDMT75HZ
Scan
Format
Standard
36655 - 2
April 2006
24 of 113
‡ When VID_STD = 4, 6, or 8, the Vblanking output pulse width is 2 lines too long for field 1 and 1 line too short for field 2 when compared to the digital timing defined in ITU-R BT.656 and
ITU-R BT.799.
† The LOCK_LOST output signal will be unstable when attempting to genlock to an input reference corresponding to VID_STD[5:0] = 51, although the device does achieve lock. To correct
this, the user can program register address 27h = 38d.
* VID_STD[5:0] = 2, 52, 53, and 54 are recognized as input references only. To generate clock and timing signals for these standards use the device’s custom format capability.
Custom format only
(Section 3.10 on
page 74)
62
Reserved
1024 x 768 XGA
@ 75 Hz
46
55 - 61
System
Nomenclature
VID_STD
[5:0]
Table 1-2: Recognized Video and Graphics Standards (Continued)
GS4911B/GS4910B Data Sheet
GS4911B/GS4910B Data Sheet
1.5 Output Timing Signals
Table 1-3 describes the output timing signals available to the user via pins
TIMING_OUT_1 to TIMING_OUT_8. The user may output any of the signals listed
below on each pin by programming the Output_Select registers beginning at
address 43h of the host interface.
s
Table 1-3: Output Timing Signals
Signal Name
Description
Default Output Pin
H Sync
The H Sync signal has a leading edge at the start of the horizontal sync pulse.
Its length is determined by the selected video standard (see Table 1-2), or
according to custom timing parameters programmed in the host interface (see
Section 3.10 on page 74).
TIMING_OUT_1
The width of the H Sync output pulse is determined by the selected video
standard. Table 1-2 lists the H Sync width (in clocks) of each pre-programmed
video and graphics standard recognized by the GS4911B/GS4910B. Custom
video timing parameters may also be programmed in the host interface to
define a unique H Sync width (see Section 3.10 on page 74).
In Genlock mode the leading edge of the output H Sync signal is nominally
simultaneous with the half amplitude point of the reference HSYNC input. This
timing may be offset using the Genlock Offset registers beginning at address
1Bh of the host interface (see Section 3.2.1.1 on page 37).
By default, after system reset, the polarity of the H Sync signal output will be
active LOW. The polarity may be selected as active HIGH by programming the
Polarity register at address 56h of the host interface (see Section 3.12.3 on
page 79).
H Blanking
The H Blanking signal is used to indicate the portion of the video line not
containing active video data.
TIMING_OUT_2
The H Blanking signal will be LOW (default polarity) for the portion of the video
line containing valid video samples. The signal will be LOW at the first valid
pixel of the line, and HIGH after the last valid pixel of the line.
The H Blanking signal remains HIGH throughout the horizontal blanking period.
The width of this signal will be determined by the selected video standard (see
Table 1-2), or according to custom timing parameters programmed in the host
interface (see Section 3.10 on page 74).
When in Genlock mode, the output H Blanking signal will be phase locked to the
reference HSYNC input. This timing may be offset using the Genlock Offset
registers beginning at address 1Bh of the host interface (see Section 3.2.1.1 on
page 37).
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3 on page 79).
36655 - 2
April 2006
25 of 113
GS4911B/GS4910B Data Sheet
Table 1-3: Output Timing Signals (Continued)
Signal Name
Description
Default Output Pin
V Sync
The V Sync timing signal has a leading edge at the start of the vertical sync
pulse. Its length is determined by the selected video standard (see Table 1-2),
or according to custom timing parameters programmed in the host interface
(see Section 3.10 on page 74).
TIMING_OUT_3
The leading edge of V Sync is nominally simultaneous with the leading edge of
the first broad pulse.
When in Genlock mode, the output V Sync signal will be phase locked to the
reference VSYNC input. This timing may be offset using the Genlock Offset
registers beginning at address 1Bh of the host interface (see Section 3.2.1.1 on
page 37).
By default, after system reset, the polarity of the V Sync signal output will be
active LOW. The polarity may be selected as active HIGH by programming the
Polarity register at address 56h of the host interface (see Section 3.12.3 on
page 79).
V Blanking
The V Blanking signal is used to indicate the portion of the video field/frame not
containing active video lines.
TIMING_OUT_4
The V Blanking signal will be LOW (default polarity) for the portion of the
field/frame containing valid video data, and will be HIGH throughout the vertical
blanking period.
The width of this signal will be determined by the selected video standard (see
Table 1-2), or according to custom timing parameters programmed in the host
interface (see Section 3.10 on page 74).
When in Genlock mode, the output V Blanking signal will be phase locked to the
reference VSYNC input. This timing may be offset using the Genlock Offset
registers beginning at address 1Bh of the host interface (see Section 3.2.1.1 on
page 37).
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3 on page 79).
NOTE: When VID_STD = 4, 6, or 8, the Vblank output pulse width is 2 lines too
long for field 1 and 1 line too short for field 2 when compared to the digital timing
defined in ITU-R BT.656 and ITU-R BT.799.
F Sync
The F Sync signal is used to indicate field 1 and field 2 for interlaced video
formats.
TIMING_OUT_5
The F Sync signal will be HIGH (default polarity) for the entire period of field 1. It
will be LOW for all lines in field 2 and for all lines in progressive scan systems.
The width and timing of this signal will be determined by the V Sync parameters
of the selected video standard (see Table 1-2), or according to custom V Sync
timing parameters programmed in the host interface (see Section 3.10 on
page 74). The F Sync signal always changes state on the leading edge of V
Sync.
When in Genlock mode, the output F Sync signal will be phase locked to the
reference FSYNC input. This timing may be offset using the Genlock Offset
registers beginning at address 1Bh of the host interface (see Section 3.2.1.1 on
page 37).
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3 on page 79).
36655 - 2
April 2006
26 of 113
GS4911B/GS4910B Data Sheet
Table 1-3: Output Timing Signals (Continued)
Signal Name
Description
Default Output Pin
F Digital
F Digital is used in digital interlaced standards to indicate field 1 and field 2.
TIMING_OUT_6
The F Digital changes state at the leading edge of every V Blanking pulse. It will
be LOW (default polarity) for the entire period of field 1 and for all lines in
progressive scan systems. It will be HIGH for all lines in field 2 .
The width and timing of this signal will be determined by the timing parameters
of the selected video standard (see Table 1-2), or according to custom
parameters programmed in the host interface (see Section 3.10 on page 74).
When in Genlock mode, the output F Digital signal will be phase locked to the
reference FSYNC input. This timing may be offset using the Genlock Offset
registers beginning at address 1Bh of the host interface (see Section 3.2.1.1 on
page 37).
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3 on page 79).
10 Field Identification
The 10 Field Identification (10FID) signal is used to indicate the 10-field
sequence for 29.97Hz, 30Hz, 59.94Hz and 60Hz video standards. It will be
LOW for output standards with other frame rates.
TIMING_OUT_7
The sequence defines the phase relationship between film frames and video
frames, so that cadence may be maintained in mixed format environments.
The 10FID signal will be HIGH (default polarity) for one line at the start of the
10-field sequence. It will be LOW for all other lines. The signal’s rising and
falling edges will be simultaneous with the leading edge of the H Sync output
signal.
Alternatively, by setting bit 4 of the Video_Control register (see Section 3.12.3
on page 79), the 10FID output signal may be configured to go HIGH (default
polarity) on the leading edge of the H Sync output on line 1 of the first field in
the 10 field sequence, and be reset LOW on the leading edge of the H Sync
pulse of the first line of the second field in the 10 field sequence.
When in Genlock mode, the output 10FID signal will be phase locked to the
10FID reference input. If a 10FID input is not provided to the device, the user
must configure the 10FID output using register 1Ah of the host interface (see
Section 3.8.1 on page 67).
For applications involving audio, this signal may be used in place of the AFS
signal if the format selected is appropriate for a 10 field AFS repetition rate, and
the desired phase relationship of audio to video clock phasing coincides with
the desired film frame cadence.
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3 on page 79).
Please see Section 3.8.1 on page 67 for more detail on the 10FID output signal.
Display Enable
The Display Enable (DE) signal is used to indicate the display enable for
graphic display interfaces.
TIMING_OUT_8
This signal will be HIGH (default polarity) whenever pixel information is to be
displayed on the display device (i.e. whenever both H Blanking and V Blanking
are in the active video state)
The width and timing of this signal will be determined by the timing parameters
of the selected video standard (see Table 1-2), or according to custom timing
parameters programmed in the host interface (see Section 3.10 on page 74).
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3 on page 79).
36655 - 2
April 2006
27 of 113
GS4911B/GS4910B Data Sheet
Table 1-3: Output Timing Signals (Continued)
Signal Name
Description
Default Output Pin
Audio Frame Sync
The Audio Frame Sync (AFS) signal is HIGH (default polarity) for the duration of
the first line of the n’th video frame to indicate that the ACLK dividers are reset
at the start of line 1 of that frame. It is defined according to the frame rate of the
video format and the selected audio sample rate programmed via the
VID_STD[5:0] and ASR_SEL[2:0] pins or the host interface.
–
(GS4911B only)
For example, if the video format is based on a 59.94Hz frame rate and the
audio sample rate clock is 48kHz, then n=5, and the AFS signal will be identical
to the 10FID signal.
By default, the AFS signal is reset by the 10 Field Identification (10FID)
reference input. This feature may be disabled using the Audio_Control register
at address 31h of the host interface (see Section 3.12.3 on page 79). The AFS
signal may also be reset using register 1Ah of the host interface. With no
reference, the frame divide by “n” controlling the AFS signal will free-run at an
arbitrary phase.
The default polarity of this signal may be inverted by programming the Polarity
register at address 56h of the host interface (see Section 3.12.3).
Please see Section 3.8.2 on page 68 for more detail on the AFS output signal.
USER_1~4
The GS4911B/GS4910B offers four user programmable output signals. Each
USER signal is controlled by four timing registers and a polarity select bit. The
timing registers define the start and stop times in H pixels and V lines and begin
at address 57h of the host interface (see Section 3.12.3 on page 79).
–
Each user signal is individually programmable and the polarity, position, and
width of each output may be defined with respect to the H, V, and F output
timings of the device. Each output signal may be programmed in both the
horizontal and vertical dimensions relative to the leading edges of H and V
Sync. If desired, the pulses produced may then be combined with a logical
AND, OR, or XOR function to produce a composite signal (for example, a
horizontal back porch pulse during active lines only, or the active part of lines 15
through 20 for vertical information retrieval). Each output has selectable
polarity.
Please see Section 3.8.3 on page 69 for more detail on the USER_1~4 output
signals.
36655 - 2
April 2006
28 of 113
GS4911B/GS4910B Data Sheet
2. Electrical Characteristics
2.1 Absolute Maximum Ratings
Parameter
Conditions
Value/Units
Supply Voltage Core and Analog
–
-0.3V to +2.1V
–
-0.3V to +3.6V
IO_VDD = +3.3V
-0.3V to +5.5V
IO_VDD = +1.8V
-0.3V to +3.6V
Operating Temperature
–
-20°C < TA < 85°C
Storage Temperature
–
-50°C < TSTG < 125°C
Soldering Temperature
–
260°C
ESD protection on all pins
–
1 kV
(CORE_VDD, VID_PLL_VDD, AUD_PLL_VDD,
PhS_VDD, ANALOG_VDD)
Supply Voltage I/O
(IO_VDD, XTAL_VDD)
Input Voltage Range (any input)
2.2 DC Electrical Characteristics
Table 2-1: DC Electrical Characteristics
VDD = 1.8V, TA = 0°C to 70°C, unless otherwise specified.
Parameter
Symbol
Condition
Min
Typ
Max
Units
Notes
Operating Temperature Range
TA
–
0
25
70
°C
1
Core power supply voltage
CORE_VDD
–
1.71
1.8
1.89
V
–
Digital I/O Buffer Power Supply
Voltage
IO_VDD
1.8V Operation
1.71
1.8
1.89
V
–
IO_VDD
3.3V Operation
3.135
3.3
3.465
V
–
Video PLL Power Supply Voltage
VID_PLL_VDD
–
1.71
1.8
1.89
V
–
Audio PLL Power Supply Voltage
(GS4911B only)
AUD_PLL_VDD
–
1.71
1.8
1.89
V
–
Analog Power Supply Voltage
ANALOG_VDD
–
1.71
1.8
1.89
V
–
Crystal Buffer Power Supply Voltage
XTAL_VDD
1.8V Operation
1.71
1.8
1.89
V
–
XTAL_VDD
3.3V Operation
3.135
3.3
3.465
V
–
PhS_VDD
–
1.71
1.8
1.89
V
–
System
Video Clock Phase Shift Supply
Voltage
36655 - 2
April 2006
29 of 113
GS4911B/GS4910B Data Sheet
Table 2-1: DC Electrical Characteristics (Continued)
VDD = 1.8V, TA = 0°C to 70°C, unless otherwise specified.
Parameter
Symbol
Condition
System Power
PD
GS4911B
CORE_VDD = Max
IO_VDD = Max
Min
Typ
Max
Units
Notes
–
–
450
mW
–
–
300
–
mW
–
–
–
400
mW
–
–
250
–
mW
–
T = 70oC
unloaded, max PCLK
frequency
PD
GS4911B
CORE_VDD = 1.8V
IO_VDD = 3.3V
T = 25oC
unloaded,
PCLK = 74.25MHz
PD
GS4910B
CORE_VDD = Max
IO_VDD = Max
T = 70oC
unloaded, max PCLK
frequency
PD
GS4910B
CORE_VDD = 1.8V
IO_VDD = 3.3V
T = 25oC
unloaded,
PCLK = 74.25MHz
Digital I/O
Input Voltage, Logic LOW
VIL
1.8V Operation
–
–
0.35 x
VDD
V
–
VIL
3.3V Operation
–
–
0.8
V
–
VIH
1.8V Operation
0.65 x
IO_VDD
–
3.6
V
–
VIH
3.3V Operation
2.145
–
5.25
V
–
Output Voltage, Logic LOW
VOL
current drive = HIGH
or LOW as selected
–
–
0.4
V
2
Output Voltage, Logic HIGH
VOH
current drive = HIGH
or LOW as selected
0.65 x
IO_VDD
–
–
V
2
–
IO_VDD = 1.8V
current drive = LOW
–
5
–
mA
–
–
IO_VDD = 3.3V
current drive = LOW
–
10
–
mA
–
–
IO_VDD = 1.8V
current drive = HIGH
–
7
–
mA
–
–
IO_VDD = 3.3V
current drive = HIGH
–
14
–
mA
–
Input Voltage, Logic HIGH
Digital Output Currents
Timing Output Drive Current
36655 - 2
April 2006
30 of 113
GS4911B/GS4910B Data Sheet
Table 2-1: DC Electrical Characteristics (Continued)
VDD = 1.8V, TA = 0°C to 70°C, unless otherwise specified.
Parameter
Symbol
Condition
Min
Typ
Max
Units
Notes
Clock Output Drive Current
–
IO_VDD = 1.8V
current drive = LOW
–
5
–
mA
–
–
IO_VDD = 3.3V
current drive = LOW
–
7
–
mA
–
–
IO_VDD = 1.8V
current drive = HIGH
–
7
–
mA
–
–
IO_VDD = 3.3V
current drive = HIGH
–
14
–
mA
–
Output Voltage LVDS, Common
Mode
VOCM
–
1.125
1.25
1.375
V
3
Output Voltage LVDS, Differential
VODIFF
–
–
350
–
mV
3
LVDS High-impedance Leakage
Current
–
To 1.8V or GND
–
–
1.4
uA
–
NOTES
1. All DC and AC electrical parameters within specification.
2. Assuming that the current being sourced or sinked is less than the Timing Output Drive Current specified.
3. Into a 100Ω termination connected between PCLK3 and PCLK3.
2.3 AC Electrical Characteristics
Table 2-2: AC Electrical Characteristics
VDD = 1.8V, TA = 0°C to 70°C, unless otherwise specified.
Parameter
Symbol
Condition
–
from when the
reference input is
first present
PCLK Output Frequency
–
–
PCLK Jitter
–
SD video standards
Min
Typ
Max
Units
Notes
–
2
4
frames
–
3.375
–
165
MHz
–
–
350
–
ps
1, 2
–
250
–
ps
1, 3
40
–
60
%
–
System
Reference Detection Time
Digital I/O
XTAL_VDD = 3.3V
–
HD & Graphics
video standards
XTAL_VDD = 3.3V
PCLK Duty Cycle
–
–
36655 - 2
April 2006
31 of 113
GS4911B/GS4910B Data Sheet
Table 2-2: AC Electrical Characteristics (Continued)
VDD = 1.8V, TA = 0°C to 70°C, unless otherwise specified.
Parameter
Symbol
Condition
PCLK1 & PCLK2 Rise/Fall Times
15pF load
20% - 80%
–
PCLK3 Rise/Fall Time
20% - 80%
Min
Typ
Max
Units
Notes
IO_VDD = 1.8V
current drive = LOW
–
–
1.7
ns
–
–
IO_VDD = 3.3V
current drive = LOW
–
–
1.5
ns
–
–
IO_VDD = 1.8V
current drive =
HIGH
–
–
1.1
ns
–
–
IO_VDD = 3.3V
current drive =
HIGH
–
–
0.9
ns
–
–
100Ω differential
load
–
–
850
ps
–
-3
–
3
ns
4
10pF to ground per
pin
PCLK Outputs Relative Timing
Skew
–
default PCLK phase
delay of zero
ACLK Frequency
(GS4911B only)
–
–
0.0097
–
49.152
MHz
–
ACLK Duty Cycle
(GS4911B only)
–
–
40
–
60
%
5
ACLK1-3 Rise/Fall Times
15pF load
20% - 80%
(GS4911B only)
–
IO_VDD = 1.8V
current drive = LOW
–
–
3.0
ns
–
–
IO_VDD = 3.3V
current drive = LOW
–
–
1.5
ns
–
–
IO_VDD = 1.8V
current drive =
HIGH
–
–
2.5
ns
–
–
IO_VDD = 3.3V
current drive =
HIGH
–
–
1.4
ns
–
ACLK Outputs Relative
Timing Skew
(GS4911B only)
–
–
-3
–
3
ns
4
Digital Timing Output Delay Time
tOD
–
–
–
4.3
ns
6
Digital Timing Output Hold Time
tOH
–
1
–
–
ns
6
36655 - 2
April 2006
32 of 113
GS4911B/GS4910B Data Sheet
Table 2-2: AC Electrical Characteristics (Continued)
VDD = 1.8V, TA = 0°C to 70°C, unless otherwise specified.
Parameter
Symbol
Condition
Min
Typ
Max
Units
Notes
Digital Timing Output Rise/Fall
Times
15pF load
20% - 80%
–
IO_VDD = 1.8V
current drive = LOW
–
–
3.0
ns
–
–
IO_VDD = 3.3V
current drive = LOW
–
–
1.5
ns
–
–
IO_VDD = 1.8V
current drive =
HIGH
–
–
2.5
ns
–
–
IO_VDD = 3.3V
current drive =
HIGH
–
–
1.4
ns
–
GSPI Input Clock Frequency
fGSPI
–
–
–
10.0
MHz
7
GSPI Clock Duty Cycle
DCGSPI
–
40
–
60
%
7
GSPI Input Setup Time
t3 in Figure 3-18
–
1.5
–
–
ns
7
GSPI Input Hold Time
t8 in Figure 3-18
–
1.5
–
–
ns
7
GSPI
NOTES
1. The video output clock may be directly connected to Gennum’s GS1532 or GS1531 serializer for a SMPTE-compliant SDI or HD-SDI
output with output jitter below 0.2UI, when the serializer is configured for a loop bandwidth of 100KHz.
2. All SD standards EXCEPT VID_STD[5:0] = 1 (450ps typ.) and VID_STD[5:0] = 5 or 6 (500ps typ.)
3. All HD and Graphics standards EXCEPT VID_STD[5:0] = 22 (300ps typ.) and VID_STD[5:0] = 41-43 (400ps typ.)
4. Timings from any CLK output to any other CLK output.
5. If fs=96kHz and ACLK is configured to output a clock signal at 192fs or 384fs, a 512fs clock will typically have a 33% duty cycle distortion.
See Section 3.7.2 on page 63.
6. With PCLK phasing delay set to nominal (zero offset), each increment of the clock phasing adjustment decreases output hold time and
delay time by a nominal 700ps. The times tOD and tOH are defined in Figure 2-1.
7. For detailed GSPI timing parameters, please refer to Table 3-12.
36655 - 2
April 2006
33 of 113
GS4911B/GS4910B Data Sheet
tOH
tOD
50%
PCLK
VOH
VOH
VOL
VOL
TIMING_OUT
Figure 2-1: PCLK to TIMING_OUT Signal Output Timing
Table 2-3: Suggested External Crystal Specification
27.000000 MHz
AT Cut
Nominal Dissipation = 50 uW
Frequency accuracy at 25°C = +/- 10ppm
Frequency variation 0-70°C = +/- 10ppm
ASR = 50 +/- 20Ω
NOTE: The user may select an appropriate crystal accuracy for their application. If the device is
operating in Free Run mode, the output clock and timing signals will have the same accuracy as
the crystal. However, if operating in Genlock mode, all output signals are based on the input
reference, and therefore a less accurate crystal may be sufficient. See Section 3.2 on page 36.
36655 - 2
April 2006
34 of 113
GS4911B/GS4910B Data Sheet
2.4 Solder Reflow Profiles
The device is manufactured with Matte-Sn terminations and is compatible with both
standard eutectic and Pb-free solder reflow profiles. MSL qualification was
performed using the maximum Pb-free reflow profile shown in Figure 2-2. The
recommended standard Pb reflow profile is shown in Figure 2-3.
Temperature
60-150 sec.
20-40 sec.
260˚C
250˚C
3˚C/sec max
217˚C
6˚C/sec max
200˚C
150˚C
25˚C
Time
60-180 sec. max
8 min. max
Figure 2-2: Maximum Pb-free Solder Reflow Profile (preferred)
60-150 sec.
Temperature
10-20 sec.
230˚C
220˚C
3˚C/sec max
183˚C
6˚C/sec max
150˚C
100˚C
25˚C
Time
120 sec. max
6 min. max
Figure 2-3: Standard Pb Solder Reflow Profile
36655 - 2
April 2006
35 of 113
GS4911B/GS4910B Data Sheet
3. Detailed Description
3.1 Functional Overview
The GS4911B/GS4910B is a highly flexible, digitally controlled clock synthesis
circuit and timing generator with genlock capability.
The device has two main modes of operation: Genlock mode and Free Run mode.
In Genlock mode, the video clock and timing outputs, will be frequency and phase
locked to the detected reference input signal. In Free Run mode, the occurrence of
all frequencies is based on a 27MHz external crystal reference.
The GS4911B/GS4910B will recognize input reference signals conforming to 36
different video standards and 16 different graphic formats. It supports
cross-locking, allowing the output to be genlocked to an incoming reference that is
different from the output video standard selected.
When the device is in Genlock mode and the input reference is removed, the
GS4911B/GS4910B will enter Freeze mode. In this mode, the output clock and
timing signals will maintain their previously genlocked phase and frequency to
within +/- 2ppm.
The user may select to output one of 8 different video sample clock rates or 13
different graphic display clock rates, or may program any clock frequency between
13.5MHz and 165MHz. The chosen clock frequency may be further internally
divided, and is available on two video clock outputs and one LVDS video clock
output pair. The video clocks may also be individually phase delayed with respect
to the timing outputs for clock skew control.
Eight user-selectable timing outputs are provided that can automatically produce
the following timing signals for 35 different video formats and 13 different graphics
formats: HSync, Hblanking, VSync, Vblanking, F sync, F digital, AFS (GS4911B
only), DE, and 10FID. Alternatively, custom output timing signals may be
programmed in the host interface.
In addition, the GS4911B provides three audio sample clock outputs that can
produce audio clocks up to 512fs with fs ranging from 9.7kHz to 96kHz. Audio to
video phasing is accomplished by either an external 10FID input reference, a
10FID signal specified via internal registers, or a user-programmed audio frame
sequence.
3.2 Modes of Operation
The GS4911B/GS4910B will operate in either Genlock mode or Free Run mode
depending on the setting of the GENLOCK pin. These two modes are described in
Section 3.2.1 on page 37 and Section 3.2.2 on page 40 respectively.
If desired, the external GENLOCK pin may be ignored by setting bit 5 of the
Genlock_Control register (address 16h) so that genlock can instead be controlled
via the host interface (see Section 3.12.3 on page 79). Although the external
GENLOCK pin will be ignored in this case, it should not be left floating.
36655 - 2
April 2006
36 of 113
GS4911B/GS4910B Data Sheet
3.2.1 Genlock Mode
When the application layer sets the GENLOCK pin LOW and the device has
successfully genlocked the outputs to the input reference, the GS4911B/GS4910B
will enter Genlock mode. In this mode, all clock and timing generator outputs will
be frequency and phase locked to the detected input reference signal. The PCLK
outputs will be locked to the H reference.
When in Genlock mode, the output clock and timing signals are generated using
the applied reference signal. The 27MHz crystal reference is necessary for
operation; however, neither crystal accuracy nor changes in crystal frequency (due
to a shift in operating temperature) will affect the output signals. For example, the
output signals will be generated with the same accuracy whether the 27MHz
reference crystal has an accuracy of 10ppm or 100ppm.
The GS4911B/GS4910B supports cross-locking, allowing the outputs to be
genlocked to an incoming reference that is different from the output video standard
selected (see Section 3.6 on page 50).
NOTE: The user must apply a reference to the input of the device prior to setting
GENLOCK = LOW. If the GENLOCK pin is set LOW and no reference signal is
present, the generated clock and timing outputs of the device may correspond to
the internal default settings of the chip until a reference is applied.
3.2.1.1 Genlock Timing Offset
By default, the phase of the clock and timing out signals is genlocked to the input
reference signal. These output signals may be phase adjusted with respect to the
input reference by programming the host interface (see Section 3.12.3 on
page 79). Offsets are separately programmable in terms of clock phase, horizontal
phase, and vertical phase (i.e. fractions of a pixel, pixels, and lines).
Genlock timing offsets can be used to co-time the output of a piece of equipment
containing the GS4911B/GS4910B with the outputs of other equipment at different
locations. The signal leaving the piece of equipment containing the
GS4911B/GS4910B may pass through processing equipment with significant fixed
delays before arriving at the switcher. These delays may include video line delays
or even field delays. To compensate for these delays, genlock timing offsets allow
the user to back-time the output of the equipment relative to the input reference.
Using the host interface, the following registers may be programmed once the
device is stably locked:
•
Clock_Phase_Offset (1Dh) - with a range of zero to one clock pulse in
increments of between 1/64 and 1/512 of a clock period (depending on the
PCLK frequency). The increments will be between 100ps and 200ps. All clock
and timing output signals will be delayed by the clock phase offset
programmed in this register.
•
H_Offset (1Bh) - the difference between the reference HSYNC signal and the
output H Sync and/or H Blanking signal in clock pulses, with a control range of
zero to +1 line. All timing output signals will be delayed by the horizontal offset
programmed in this register.
36655 - 2
April 2006
37 of 113
GS4911B/GS4910B Data Sheet
•
V_Offset (1Ch) - the difference between the reference VSYNC signal and the
output V Sync and/or V Blanking in lines, with a control range of zero to +1
frame. All line-based timing output signals will be delayed by the vertical offset
programmed in this register.
The encoding scheme for the Clock_Phase_Offset register (1Dh) is shown in
Table 3-1. The offset programmed will be in the positive direction. Note that the
step size will depend on the frequency of the output video clock.
NOTE: If VID_STD[5:0] = 63 and the reference format is changed, care must be
taken to ensure that the Clock_Phase_Offset register is correctly programmed for
the new output format before the reference is applied.
Table 3-1: Clock_Phase_Offset[15:0] Encoding Scheme
VID_STD[5:0]
Setting
Output Video Clock
Frequency
1
fPCLK < 20MHz
3-6, 39-42
Step Size
(Fraction
of a
PCLK)
Maximum
Number of
Steps
Bits Required to
Set the Number
of Steps
Clock_Phase_Offset
[15:0] Settings
1
--------512
511
b 8b 7b6b5 b4b3b2 b1b0
b8000001b8b7b6b5b4b3b2b1b0
20MHz < fPCLK < 40MHz
1-------256
255
b 7b6 b5b4b3 b2b1b0
b7000010b7b6b5b40b3b2b1b0
7-20, 25-38, 43-46
40MHz < fPCLK < 80MHz
1-------128
127
b 6b5b4 b3b2b1 b0
b6000100b6b5b400b3b2b1b0
21-23, 47-51
fPCLK > 80MHz
1----64
63
b5 b4b3b2 b1b0
b5001000b5b4000b3b2b1b0
Note: Program Clock_Phase_Offset = 0000 0000 0000 0000b to achieve a zero clock phase offset.
The value programmed in the H_Offset register (1Bh) must not exceed the
maximum number of clock periods per line of the outgoing video standard.
Similarly, the value programmed in the V_Offset register (1Ch) must not exceed
the maximum number of lines per frame of the outgoing standard. Both horizontal
and vertical offsets will be in the positive direction. Negative offsets (advances) are
achieved by programming a value in the appropriate register equal to the maximum
allowable offset minus the desired advance.
NOTES:
1. The device will delay all output timing signals by 2 PCLKs relative to the input
HSYNC reference. This will occur even when the H_Offset register is not
programmed. The user may compensate for this delay by subtracting 2 PCLK
cycles from the desired horizontal offset before loading the value into the host
interface.
36655 - 2
April 2006
38 of 113
GS4911B/GS4910B Data Sheet
2. For both sync and blanking-based input references, the device will advance all
line-based output timing signals by 1 line relative to the input VSYNC
reference for all output standards except VID_STD[5:0] = 4, 6, and 8. This will
occur even when the V_Offset register is not programmed. The user may
compensate for this advance by adding 1 line to the desired vertical offset
before loading this value into the register.
3. When locking the "f/1.001" HD output standards to the 525-line SD input
reference standards, or vice versa, the device will delay all line-based output
timing signals by ΔVSync lines relative to the input VSYNC reference. This will
occur even when the V_Offset register is not programmed. The user may
compensate for this delay by subtracting ΔVSync lines from the desired
vertical offset before loading this value into the register.
The value ΔVSync is given by the equation:
Δ VSync = HSYNC_IN_Period + Δ VSYNC _HSYNC – ( 2 × HSYNC_OUT_Period )
where:
HSYNC_IN_Period = the period of the H reference pulse
ΔVSYNC_HSYNC = the time difference between the leading edges of the
applied V and H reference pulses
Hsync_OUT_Period = the period of the generated H Sync output
See Figure 3-1. H_Feedback_Divide represents the numerator of the ratio of
the output clock frequency to the frequency of the H reference pulse. It is
calculated as described in Section 3.6.2.1 on page 54.
HSYNC_IN_Period
HSYNC
Δ VSYNC_HSYNC
VSYNC
HSync_OUT_Period
H Sync
V Sync
Δ VSync
Figure 3-1: HD-SD Calculation
36655 - 2
April 2006
39 of 113
GS4911B/GS4910B Data Sheet
4. For sync-based input references, the device will advance all line-based output
timing signals by 1 line if the value programmed in the H_Offset register is
greater than 20. The user may compensate for this advance by adding 1 line
to the desired vertical offset before loading this value into the register. In
addition, the internal V_lock and F_lock signals reported in bits 3 and 4 of
register 16h will be LOW when H_Offset = 21 only, although the device will
remained genlocked. The user may choose to mask these lock signals such
that the device will continue to report genlock under this condition.
5. For blanking-based input references, the device will advance all line-based
output timing signals by 1 line if the value programmed in the H_Offset register
is greater than the number of output video clock cycles from the start of H
Sync to the end of active video (Hsync_to_EAV) + 20. The value of
Hsync_to_EAV is reported in register 51h and changes according to the output
VID_STD selected. The user may compensate for this advance by adding 1
line to the desired vertical offset before loading this value into the register. In
addition, the internal V_lock and F_lock signals reported in bits 3 and 4 of
register 16h will be LOW when H_Offset = Hsync_to_EAV + 21 only, although
the device will remained genlocked. The user may choose to mask these lock
signals such that the device will continue to report genlock under this
condition.
6. The offsets that occur as described in notes 1-5 are independent of one
another and must be accounted for as such.
3.2.1.2 Freeze Mode
When the device is in Genlock mode and the input reference is removed, the
GS4911B/GS4910B will enter Freeze mode. The behaviour of the device during
loss and re-acquisition of an input reference signal is described in Section 3.5.3 on
page 47.
In Freeze mode, the frequency of the output clock and timing signals will be
maintained to within +/- 2ppm. This assumes a loop bandwidth of 10Hz. Also, if the
frequency of the 27MHz reference crystal shifts while in Freeze mode, the
frequency of the output clock and timing signals will shift as well.
3.2.2 Free Run Mode
The GS4911B/GS4910B will enter Free Run mode when the GENLOCK pin is set
HIGH by the application layer. In this mode, the occurrence of all frequencies is
based on the external 27MHz reference input. Therefore, the frequency of the
output clock and timing signals will have the same accuracy as the crystal
reference.
If operating in Free Run mode, using a more accurate crystal (e.g. 10ppm) ensures
more accurate clock and timing signals are generated.
NOTE: In Free Run mode, the audio clocks of the GS4911B will remain genlocked
to the video clock.
36655 - 2
April 2006
40 of 113
GS4911B/GS4910B Data Sheet
Figure 3-2 summarizes the differences in output accuracy in each mode of
operation. Assuming a crystal reference of +/-100ppm, in Free Run mode the
frequency of the output clock and timing signals will be as accurate as the crystal.
In Genlock mode the frequency will be as accurate as the input reference
regardless of the crystal accuracy. In Freeze mode, the frequency of the output
clock and timing signals will be maintained to within +/- 2ppm.
Assumption: Reference
XTAL is 27MHz+/-100ppm
+ t
t
+100ppm
+ t
+2ppm
-2ppm
74.25 MHz
- t
-100ppm
- t
Free Run
Genlock
Freeze
No Input
Reference
Reference
Applied
Reference
Lost
Time
NOTES:
1. t represents the temperature variability of the crystal
2. Diagram not to scale.
Figure 3-2: Output Accuracy and Modes of Operation
36655 - 2
April 2006
41 of 113
GS4911B/GS4910B Data Sheet
3.3 Output Timing Format Selection
At device power-up (described in Section 3.14 on page 106), the application layer
should immediately set the external VID_STD[5:0] and ASR_SEL[2:0] pins. The
VID_STD[5:0] pins are used to select a pre-programmed output video format, or to
indicate that custom timing parameters will be programmed in the host interface.
The ASR_SEL[2:0] pins are only available on the GS4911B, and are used to select
the fundamental audio frequency or to turn off audio clock generation.
The output timing formats selectable by the user via the VID_STD[5:0] pins are
listed in Section 1.4 on page 20. Table 3-7 in Section 3.7.2 on page 63 lists the
audio sample rates available via the ASR_SEL[2:0] pins.
If the user sets VID_STD[5:0] =1-51 on power-up, the device will first check the
status of the GENLOCK pin. If GENLOCK is set LOW and a valid reference has
been applied to the inputs, the device will output the selected video standard while
attempting to genlock. However, if a reference signal has not been applied and
GENLOCK=LOW, the initial clock and timing outputs may be determined by the
internal default settings of the chip. If GENLOCK is set HIGH, the device will
immediately enter Free Run mode and will correctly output the selected video
standard.
If the user sets VID_STD[5:0] = 62 on power-up, the device will be configured to
generate custom output timing signals. The initial output timing signals will be equal
to the internal default timing of the chip until the user programs registers 4Eh to 55h
of the host interface (see Section 3.10 on page 74). Additionally, the output video
clock will run at a frequency determined by the internal default settings of the chip
until the user modifies it via registers 20h to 23h (see Section 3.9.1 on page 72).
If the user sets VID_STD[5:0] = 63 on power-up, the device will wait until a valid
reference has been applied, at which time it will output the same video format as
the input reference and enter Genlock mode if GENLOCK = LOW.
When operating in Free Run or Genlock mode, the GS4911B/GS4910B will
continuously monitor the settings of the VID_STD[5:0] and ASR_SEL[2:0] pins. If
the user wishes to change the format of the output clocks and timing signals, these
pins may be reconfigured at any time, although it is recommended that the device
be reset when changing output video standards.
36655 - 2
April 2006
42 of 113
GS4911B/GS4910B Data Sheet
3.4 Input Reference Signals
The HSYNC, VSYNC, FSYNC, and 10FID reference signals are applied to the
GS4911B/GS4910B via the designated input pins.
To operate in Genlock mode, the input reference signals must be valid and must
conform to a recognized video or graphics standard (see Section 3.5 on page 45).
Alternatively, if VID_STD[5:0] = 62, the signal applied to the HSYNC input must be
stable and have a period of less than 2.4ms.
In Free Run mode, no input reference is required.
Section 3.4.1 on page 43 describes the HSYNC, VSYNC and FSYNC input timing.
The 10FID input signal is discussed in Section 3.4.2 on page 44.
3.4.1 HSYNC, VSYNC, and FSYNC
Timing for Video Formats
The HSYNC, VSYNC, and FSYNC input reference signals may have analog
timing, such as from Gennum’s GS4981/82 sync separators (Figure 3-3), or may
have digital timing, such as from Gennum’s GS1559/60A/61 deserializers
(Figure 3-4). Section 1.4 on page 20 lists the 36 pre-programmed video timing
formats recognized by the GS4911B/GS4910B.
If the input reference format does not include an F sync signal, the FSYNC pin
should be held LOW.
HSYNC
VSYNC
FSYNC
Figure 3-3: Example HSYNC, VSYNC, and FSYNC Analog Input Timing from a
Sync Separator
PCLK
LUMA DATA OUT
3FF
000
000
XYZ (eav)
3FF
000
000
XYZ (sav)
CHROMA DATA OUT
3FF
000
000
XYZ (eav)
3FF
000
000
XYZ (sav)
H
V
F
H:V:F TIMING - HD 20-BIT OUTPUT MODE
H Signal Timing
Typical H Timing
Alternative H Timing
Figure 3-4: Example H Blanking, V Blanking, and F Digital Input Timing from an
SDI Deserializer
36655 - 2
April 2006
43 of 113
GS4911B/GS4910B Data Sheet
Timing for Graphics Formats
The GS4911B/GS4910B is pre-programmed to recognize the timing for 16
different graphics formats presented to the input reference pins. These graphic
formats are described in Section 1.4 on page 20.
The supported graphics standards are all progressive, and do not use the FSYNC
signal. Therefore, FSYNC should be held LOW by the application layer. The VESA
formats supported have a 0.5% frequency tolerance.
VSYNC transitions are typically co-timed with the leading edge of HSYNC. The
duration and polarity of these signals for each format is listed in Table 1-2.
NOTE: The user must ensure that the input HSYNC polarity for VID_STD [5:0] = 47
and 49 – 54 be active LOW.
3.4.2 10FID
The 10FID input is a reset pin, which can be used to reset the divider for the 10FID
output signal. In the GS4911B, the 10FID input pin will also reset the divider for the
AFS output signal. This default setting may be modified using the Audio_Control
register of the host interface (see Section 3.12.3 on page 79).
The GS4911B will reset the phase of the audio clocks to the leading edge of the H
Sync output on line 1 of every output frame in which the 10FID input is HIGH. This
enables the user to reset the phase of the dividers when generating custom signals
via the host interface (see Section 3.7.2.1 on page 65).
If the input reference format does not include a 10 Field ID signal, the external
10FID input pin should be held LOW.
The timing of the 10FID input signal is shown in Figure 3-5.
Total Line
10FID Input
Line 1, Frame 1 every 'n' frames
Horizontal Sync Input
Line 1 every n frames where:
n = 5 @ 29.97 fps, 30 fps
n = 10 @ 59.94 fps, 60 fps
Figure 3-5: 10FID Input Timing
36655 - 2
April 2006
44 of 113
GS4911B/GS4910B Data Sheet
3.4.3 Automatic Polarity Recognition
To accommodate any standards that employ the polarity of the H and V sync
signals to indicate the format of the display, the GS4911B/GS4910B will recognize
H and V sync polarity and automatically synchronize to the leading edge.
The polarities of the HSYNC and VSYNC signals are reported in bits 3 and 4 of the
Video_Status register. Additionally, bit 2 of this register reports the detection of
either analog or digital input timing. See Section 3.12.3 on page 79 for detailed
register descriptions.
3.5 Reference Format Detector
The reference format detector checks the validity and analyzes the format of the
input reference signal. It is designed to accurately differentiate between 59.94 and
60Hz frame rates.
3.5.1 Horizontal and Vertical Timing Characteristic Measurements
When a reference signal is applied to the designated input pins, the
GS4911B/GS4910B will analyse the signal and report the following in registers
0Ah to 0Eh of the host interface:
•
the number of 27MHz clock pulses between leading edges of the H input
reference signal (H_Period register)
•
the number of 27MHz clock pulses in 16 horizontal periods (H_16_Period
register)
•
the number of H reference pulses between leading edges of the V input
reference signal (V_Lines register)
•
the number of H reference pulses in two vertical periods (V_2_Lines register)
•
the number of H reference pulses in one F period (F_Lines register)
These parameters may be read via the host interface and are used by the device
to determine reference signal validity.
3.5.2 Input Reference Validity
Before the device attempts to operate in Genlock mode, the input signals applied
to HSYNC and VSYNC must be valid and must conform to one of the 36
recognized video standards or 16 recognized graphics standards described in
Section 1.4 on page 20. Alternatively, if VID_STD[5:0] = 62, the device may be
manually programmed to genlock to a reference that is neither valid nor recognized
(see Section 3.10.1 on page 74).
For an input reference signal to be considered valid, the periodicity of HSYNC must
be between 9us and 70us, and the periodicity of VSYNC must be between 8ms and
50ms. The FSYNC signal is not essential for validity. For output video standards
other than VID_STD[5:0] = 62, the REF_LOST pin will be set LOW once the input
reference signal is considered valid.
36655 - 2
April 2006
45 of 113
GS4911B/GS4910B Data Sheet
If the input signal is valid, the device then compares the timing parameters of the
input reference signal to each of the 36 video and 16 graphics standards listed in
Table 1-2, and determines if the input reference is one of the recognized
standards. If it is, the VID_STD[5:0] value for the format is written to the
Input_Standard register at address 0Fh of the host interface. If the input signal is
invalid, or if the reference format is unrecognized, 00h is programmed in this
register.
Once a reference signal is valid and recognized by the device, VSYNC and FSYNC
will no longer be monitored. Loss of signal on these pins will not affect the operation
of the device.
If VID_STD[5:0] is not set to 62 and the REF_LOST pin is HIGH, or if the input
signal is valid, but unrecognized as one of the 36 video or 16 graphics formats, the
GENLOCK pin should not be set LOW.
If VID_STD[5:0] = 62, the REF_LOST output will reflect the presence of a stable
signal with a period of less than 2.4ms on the HSYNC input pin. This allows the
user to program the device to lock to a single input reference only
The REF_LOST output pin may also be read via bit 0 of the Genlock_Status
register (see Section 3.12.3 on page 79).
3.5.2.1 Ambiguous Standard Selection
There are some standards with identical H, V, and F timing parameters, such that
the GS4911B/GS4910B’s reference format detector cannot distinguish between
them. Table 3-2 groups standards with shared H, V, and F periods. Using the
Amb_Std_Sel register at address 10h of the host interface, the user may select
their choice of standard to be identified with a particular set of measurements. For
example, to have 1716 clocks of 27MHz per line with 525 lines per frame identified
as 4fsc 525, program Amb_Std_Sel[10:0] = XXX10XXXXXX, where ‘X’ signifies
‘don’t care’.
36655 - 2
April 2006
46 of 113
GS4911B/GS4910B Data Sheet
Table 3-2: Ambiguous Standard Identification
Number
1
2
3
4
5
6
Standard
H
(27MHz
Clocks)
16_H
(27MHz
Clocks)
V (lines)
F (lines)
Amb_Std_Sel[10:0]
1920x1080/60/2:1 interlace
800
12800
562.5
1125
XXXXXXXXX00
1920x1080/30/PsF
800
12800
562.5
1125
XXXXXXXXX01
1920x1035/60/2:1 interlace
800
12800
562.5
1125
XXXXXXXXX10
1920x1080/59.94/2:1 interlace
800.8
12813
562.5
1125
XXXXXXX00XX
1920x1080/29.97/PsF
800.8
12813
562.5
1125
XXXXXXX01XX
1920x1035/59.94/2:1 interlace
800.8
12813
562.5
1125
XXXXXXX10XX
1920x1080/50/2:1 interlace
960
15360
562.4
1125
XXXXX00XXXX
1920x1080/25/PsF
960
15360
562.4
1125
XXXXX01XXXX
601 525 / 2:1 interlace
1716
27456
262.5
525
XXX00XXXXXX
720x486/59.94/2:1 interlace
1716
27456
262.5
525
XXX01XXXXXX
4fsc 525 / 2:1 interlace
1716
27456
262.5
525
XXX10XXXXXX
601 - 18MHz 525/2:1 interlace
1716
27456
262.5
525
XXX11XXXXXX
601 625 / 2:1 interlace
1728
27648
312.5
625
X00XXXXXXXX
720x576/50/2:1 interlace
1728
27648
312.5
625
X01XXXXXXXX
Composite PAL 625/2:1/25
1728
27648
312.5
625
X10XXXXXXXX
601 - 18MHz 625/2:1 interlace
1728
27648
312.5
625
X11XXXXXXXX
857.14
13714
525
525
0XXXXXXXXXX
858
13728
525
525
1XXXXXXXXXX
640 x 480 VGA @ 60Hz
720x483/59.94/1:1 progressive
NOTE: ‘X’ signifies ‘don’t care.’ The X bit will be ignored when determining which standard to select in each of the 6 groups above.
3.5.3 Behaviour on Loss and Re-acquisition of the Reference Signal
By default, the GS4911B/GS4910B will ignore one missing H pulse on the HSYNC
pin and will continue to operate in Genlock mode (although the LOCK_LOST pin
will temporarily be set HIGH). This behaviour is controlled by the Run_Window bits
of register address 24h.
If there are two consecutive missing H pulses on the HSYNC input pin, the
REF_LOST and LOCK_LOST pins will both go HIGH and the device will enter
Freeze mode. An internal flywheel ensures the selected output clock and timing
signals maintain their previous phase and frequency and continue to operate
without glitches.
The VSYNC and FSYNC signals are not monitored in Genlock mode; loss of signal
on these pins will not affect the operation of the device.
NOTE 1: If the input reference is removed and re-applied, all line-based timing
outputs will be inaccurate for up to one frame for all output standards.
36655 - 2
April 2006
47 of 113
GS4911B/GS4910B Data Sheet
NOTE 2: When locking the “f/1.001” HD output standards to the SD input reference
standards 3, 5, 7, or 9, or vice versa, there may be a random phase difference
between the input VSYNC and output V Sync signals occuring each time the input
reference is removed and re-applied. This will affect all line-based timing outputs.
For cases where the user must manually video genlock the device, the problem will
occur whenever the value programmed for H_Reference_Divide (registers 2B-2Ah)
is greater than 1. The user may reset the line-based counters after the reference is
re-applied without disrupting the pixel or audio clocks by toggling bit 15 of register
address 83h in the host interface. This will cause the input VSYNC and line-based
timing output signals to take on their default timing relationship, as described in
Note 3 of Section 3.2.1.1 on page 37.
Re-acquisition of the Same Reference
Upon re-application of the reference signal, the device checks whether the
reference has drifted more than +/- 2us from its expected location by comparing
the current relative position of the H pulses with the previous position, over a
16-line interval. If the reference returns with the H pulses in the expected location
+/- 2us, the PLL will drift lock and the clock generator will continue to operate
without a glitch. The REF_LOST and LOCK_LOST pins will be set back LOW.
If the reference returns with the H pulses outside the +/- 2us window, the device
will crash lock the output timing to the new input phase. The principles of crash lock
and drift lock are described in Section 3.6.3 on page 58.
NOTE: To resume proper genlock operation upon re-application of the reference
signal, the user must implement the following register manipulation every time the
reference is removed and re-applied:
1. Read the value contained in register address 24h
2. Clear the Run_Window bits [2:0] of register 24h
3. Re-write the value read in step 1 to register address 24h.
This procedure will force the device to lock to the reference as described above,
but will maintain the flywheeling capability of the GS4911B/GS4910B should a
single missing H pulse occur in the genlocked state.
To avoid the above procedure, the user may choose to clear the Run_Window bits
[2:0] of register address 24h upon power-up or reset. However, this will disable the
flywheeling feature of the device that allows it to maintain genlock through one
missing input H pulse.
36655 - 2
April 2006
48 of 113
GS4911B/GS4910B Data Sheet
Acquisition of a New Reference
When a new reference is applied, the device continues to operate in Freeze mode
while the reference format detector checks for validity as described in Section 3.5.2
on page 45. Once validity is detected, the REF_LOST pin is set LOW.
Assuming GENLOCK is LOW, the device will then attempt to genlock the selected
output clock and timing signals to the new input reference. If the output can be
automatically genlocked to the new input reference, LOCK_LOST will go LOW and
the device will re-enter Genlock mode. Otherwise, the LOCK_LOST pin will remain
HIGH and the device will enter Free Run mode.
If VID_STD[5:0] = 63 when the new reference is applied, the device will send the
detected timing parameters to the clock synthesis and timing generator blocks. The
new output format will start being generated during the first reference V period after
the reference format has been reliably established. The LOCK_LOST pin will go
LOW and the device will re-enter Genlock mode.
3.5.4 Allowable Frequency Drift on the Reference
By default, the frequency of the reference H pulse on HSYNC may drift from its
expected value by approximately +/- 0.2% before the internal video PLL loses lock.
This tolerance may be adjusted using the Max_Ref_Delta register at address 1Eh
of the host interface.
The encoding scheme is shown in Table 3-3. The default value of the register is Bh.
NOTE: Regardless of the setting of this register, the device will always differentiate
between 59.94Hz and 60Hz reference standards.
Table 3-3: Max_Ref_Delta Encoding Scheme
Register
Setting
Maximum Allowable
Frequency Drift
Register
Setting
Maximum Allowable
Frequency Drift
0h
+/- 2 -20
8h
+/- 2 -12
1h
+/- 2 -19
9h
+/- 2 -11
2h
+/- 2 -18
Ah
+/- 2 -10
3h
+/- 2 -17
Bh
+/- 2 -9
4h
+/- 2 -16
Ch
+/- 2 -8
5h
+/- 2 -15
Dh
+/- 2 -7
6h
+/- 2 -14
Eh
+/- 2 -6
7h
+/- 2 -13
Fh
+/- 2 -5
The maximum allowable frequency drift is measured as a fraction of the frequency of the reference
H pulse.
36655 - 2
April 2006
49 of 113
GS4911B/GS4910B Data Sheet
3.6 Genlock
When both the REF_LOST output and the GENLOCK input are LOW, the device
will attempt to genlock the output clock and timing signals to the input reference.
NOTE: The user must apply a reference to the input of the device prior to setting
GENLOCK = LOW. If the GENLOCK pin is set LOW and no reference signal is
present, the generated clock and timing outputs of the device may correspond to
the internal default settings of the chip until a reference is applied.
The device will first attempt to automatically genlock the output to the input
reference. This automatic locking process is described in Section 3.6.1 on
page 50. If the output format selected is such that it is not commonly genlocked to
the input reference, the GS4911B/GS4910B will not automatically lock. In this
case, the user may program designated registers to manually allow locking to
occur. The manual locking process is described in Section 3.6.2 on page 54.
The user may disable one or more of the recognized input standards from being
used to genlock the output by setting the Reference_Standard_Disable register
located at address 11h - 14h of the host interface. If a reference is applied that is
disabled in the Reference_Standard_Disable register, both the automatic and
manual locking process will fail when the application layer sets GENLOCK = LOW.
NOTE: If the device is already genlocked to an input reference and the applied
standard is subsequently disabled in the Reference_Standard_Disable register,
the device will remain locked.
3.6.1 Automatic Locking Process
The behaviour of the device when attempting to automatically genlock will depend
on the status and format of the input reference with respect to the selected output
format.
VID_STD[5:0] = 1 to 51:
Once reference validity is established and the reference format is recognized, the
device uses an internal cross-reference genlock look-up table to determine
whether the input can be used to genlock the output. A simplified version of this
look-up table is shown in Table 3-4. The table represents a matrix with the
VID_STD[5:0] number representation of each possible reference format along the
top axis, and the VID_STD[5:0] representation of each possible output timing
format along the vertical axis. A shaded box indicates that the output format can be
automatically genlocked to the input reference.
If the device determines that the output can be automatically genlocked to the input
reference, it will lock the output format to the reference, adjust the output timing
signals based on the genlock timing offset registers (Section 3.2.1.1 on page 37),
and then set the LOCK_LOST pin LOW.
36655 - 2
April 2006
50 of 113
GS4911B/GS4910B Data Sheet
If the device cannot automatically genlock the output to the applied reference, the
LOCK_LOST pin will be set HIGH and the device will operate in Free Run mode.
In this case, the user may program designated registers to manually allow locking
to occur (Section 3.6.2 on page 54).
Individual H, V, and F-locked signals can be read from the Genlock_Status register
of the host interface. Additionally, designated bits in the Genlock_Control register
may be configured to permit the genlock block to ignore invalid timing on the
HSYNC, VSYNC, or FSYNC pin when determining the locked status of the device.
These registers are described in Section 3.12.3 on page 79.
NOTE: When attempting to lock some output graphics standards to an input
reference, the device will automatically modify the output frame rate from the VESA
standard to permit cross-locking to occur. The exact change will depend on the
output standard selected and the input reference detected. Standards affected by
this behaviour are denoted by an 'a' or a 'b' suffix in Table 3-4.
VID_STD[5:0] = 62:
Setting VID_STD[5:0]=62 allows custom timing signals to be programmed in the
host register (see Section 3.10 on page 74). It has the additional feature of
disabling the validity check of the input reference signal.
The device will automatically attempt to genlock the custom output to the input
using the same process that is used when VID_STD[5:0] = 1 to 51. The user must
manually program the internal genlock block if a custom H-based timing output
signal is programmed or if a custom reference pulse is applied to HSYNC.
VID_STD[5:0] = 63:
When VID_STD[5:0]=63, the device will send the detected input reference timing
parameters to the clock synthesis and timing generator blocks. The device will
produce an output format with identical timing to the input reference. It will then lock
the output format to the reference, adjust the output timing parameters based on
the genlock timing offset registers (Section 3.2.1.1 on page 37), and set the
LOCK_LOST pin LOW.
36655 - 2
April 2006
51 of 113
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Continued on next page...
Input Reference Format
1
2
3
4
5
6
7
8
9
11
12
13
36655 - 2
10
14
Table 3-4: Cross-reference Genlock Table
16
17
18
April 2006
15
19
20
21
22
23
25
26
27
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
52
53
54
52 of 113
51
GS4911B/GS4910B Data Sheet
36655 - 2
April 2006
A shaded box indicates that the selected output format can be automatically genlocked to the input reference.
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
39a
42a
45a
46a
49a
50a
39b
40b
42b
43b
45b
46b
49b
50b
51b
NOTES:
Suffix a numbers are modified from the VESA standard to have exact 60Hz, 75Hz, or 85Hz frame rates.
Suffix b numbers are modified from the VESA standard to have 60/1.001Hz, 75/1.001Hz, or 85/1.001Hz frame rates.
Input Reference Format
1
2
3
4
5
Table 3-4: Cross-reference Genlock Table (Continued)
21
22
23
25
26
27
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
52
53
54
53 of 113
51
GS4911B/GS4910B Data Sheet
GS4911B/GS4910B Data Sheet
3.6.2 Manual Locking Process
Using the host interface, the GS4911B/GS4910B may be manually programmed to
genlock certain video formats and audio clocks that are not automatically
genlocked by the device. The following sections discuss when the user should
manually program the internal video and/or audio genlock block, and how these
blocks are programmed.
3.6.2.1 Programming the Internal Video Genlock Block and Output Line/Frame Reset Registers
The user will be required to manually program the internal video genlock block and
output line/frame reset registers during any of the following situations:
1. The pre-programmed output format and input reference cannot be
automatically genlocked according to the cross-reference genlock table
(Table 3-4 in Section 3.6.1 on page 50).
2. A custom video clock is programmed in the host interface (Section 3.9.1 on
page 72).
3. VID_STD[5:0] = 62 and a custom H-based timing output signal is programmed
(see Section 3.10 on page 74).
4. VID_STD[5:0] = 62 and a custom reference pulse is applied to HSYNC (see
Section 3.10.1 on page 74).
Video Genlock Block Host Registers
A simplified version of the GS4911B/GS4910B’s internal video genlock block is
shown in Figure 3-6.
27MHz
Internal Video Genlock Block
HSYNC
(fHref (
H_Reference_Divide
(host address 2Ah - 2Bh)
Phase
Comparator
Clock
Synthesizer
Output Video
Clock
(fout (
H_Feedback_Divide
(host address 28h - 29h)
Figure 3-6: Internal Video Genlock Block
To genlock the output clock and video timing signals to the input format, the user
must first lock the frequency of the output video clock (fout) to the frequency of the
reference pulse on HSYNC (fHref). This is accomplished by programming the set of
integers (H_Feedback_Divide, H_Reference_Divide) in the equation:
f out
H_Feedback_Divide
-------------------------------------------------- = ---------H_Reference_Divide
f Href
36655 - 2
April 2006
54 of 113
GS4911B/GS4910B Data Sheet
where:
fout = output video clock frequency
fHref = reference H pulse frequency on HSYNC
H_Feedback_Divide = numerator of the divide ratio (host register 28h-29h)
H_Reference_Divide = denominator of the divide ratio (host register 2Ah-2Bh)
Before programming H_Feedback_Divide and H_Reference_Divide, the
numerator and denominator must be reduced to their lowest factors.
For example, to manually genlock an output format with a 74.25MHz video clock to
a reference with a 27MHz video clock and 1716 clocks per line, the following
calculations are necessary:
27
f Href = ------------ MHz
1716
H_Feedback_Divide
1716 127413
∴-------------------------------------------------- = 74.25MHz
-------------------------- = 74.25 × ------------ = ------------------ = 4719
-----------H_Reference_Divide
27
27
27
1
------------ MHz
1716
Therefore, program H_Feedback_Divide = 4719 and H_Reference_Divide = 1.
Output Line/Frame Reset Host Registers
In addition to programming H_Feedback_Divide and H_Reference_Divide, the
user must also define the ratio of the output frame rate to the reference frame rate.
The denominator of this ratio is programmed in the Output_FV_Reset register at
address 18h of the host interface. Before Output_FV_Reset is programmed, the
numerator and denominator must be reduced to their lowest factors. Two
examples are demonstrated below:
Example 1: the reference has a frame rate of 30Hz and the output frame rate is
50Hz:
Output
Frame Rate- = 50
------ = 5----------------------------------------------30 3
Input Frame Rate
Therefore, program Output_FV_Reset = 3. The numerator does not have to be
programmed.
Example 2: the reference has a frame rate of 29.97Hz and the output frame rate is
50Hz:
50 - 1001
Output
Frame Rate- = -------------------------------------------------------= -----------29.97 600
Input Frame Rate
Therefore, program Output_FV_Reset = 600. The numerator does not have to be
programmed.
Additionally, the Frame_Divider_Reset register (address19h) must be configured
to initialize the counter reset programmed in register 18h.
36655 - 2
April 2006
55 of 113
GS4911B/GS4910B Data Sheet
Alternatively, depending on the information available, the user may program the
Output_H_Reset register (address 17h) instead of programming registers 18h and
19h. Output_H_Reset defines the denominator of the ratio of the output line
frequency to the input line frequency. Before Output_H_Reset is programmed, the
numerator and denominator must be reduced to their lowest factors.
For example, to genlock the output standard 720p/59.94 at 74.25/1.001MHz to the
input standard 525i/29.97 at 27MHz:
Input Video Clock Frequency
27000000
Input Line Frequency = ---------------------------------------------------------------------- = -----------------------Video Clocks per Input H
1716
Video Clock Frequency
74250000 1000
Ouput Line Frequency = Output
----------------------------------------------------------------------------- = ------------------------ × -----------1650
1001
Video Clocks per Output H
Output Line Frequency
× 1000 × 1716- = 20
∴-------------------------------------------------------- = 74250000
---------------------------------------------------------------Input Line Frequency
27000000 × 1001 × 1650
7
Therefore, program Output_H_Reset = 7. The numerator does not have to be
programmed.
NOTE: Either register 17h OR registers 18h and 19h should be programmed.
Programming all three registers will trigger two counter resets.
Programming OUTPUT_FV_RESET is preferred in all cases except where a
custom reference pulse is used in VID_STD[5:0] = 62 (see Section 3.10.1 on
page 74). In this case, OUTPUT_H_RESET must be used.
3.6.2.2 Programming the Internal Audio Genlock Block (GS4911B only)
By default, the audio clocks are always genlocked to the output video clock.
However, if a custom video or audio clock is programmed in the host interface (see
Section 3.9 on page 72), the user must manually program the internal audio
genlock block.
A simplified version of the GS4911B’s internal audio genlock block is shown in
Figure 3-7.
27MHz
Internal Audio Genlock Block
Output Video
Clock
(fout (
A_Reference_Divide
(host address 3Dh - 3Eh)
Phase
Comparator
Clock
Synthesizer
Integer Multiple of
the Fundamental
Audio Sampling Clock
(n * fs (
A_Feedback_Divide
(host address 3Bh - 3Ch)
Figure 3-7: Internal Audio Genlock Block
36655 - 2
April 2006
56 of 113
GS4911B/GS4910B Data Sheet
To genlock the audio clock to the video clock, the user must lock the fundamental
sampling frequency (fs) to the frequency of the output video clock (fout). This is
accomplished by programming the set of integers (A_Feedback_Divide,
A_Reference_Divide) in the equation:
fs
A _Feedback_Divide------------------------------------------------= n × -------f out
A_Reference_Divide
where:
fs = the fundamental audio sampling frequency
fout = output video clock frequency
A_Feedback_Divide = numerator of the divide ratio (host register 3Bh-3Ch)
A_Reference_Divide = denominator of the divide ratio (host register 3Dh-3Eh)
n = an integer constant
The integer constant, n, will depend on the fundamental audio sampling frequency.
It will be one of the three values as defined in Table 3-5.
Table 3-5: Integer Constant Value
ASR_SEL[2:0]=100b
Enable_384fs = 0
Value of constant (n)
NO
X
3072
YES
YES
1024
YES
NO
1536
NOTES:
1. Enable_384fs corresponds to bit 5 of address 31h of the host interface. It is LOW by default.
2. ‘X’ signifies ‘don’t care.’ This bit will be ignored when determining n.
Before programming A_Feedback_Divide and A_Reference_Divide, the
numerator and denominator must be reduced to their lowest factors.
For example, to manually genlock a custom audio clock with a fundamental
sampling frequency of 42kHz to a 27MHz video clock, the following calculations are
necessary:
n = 1024
A _Feedback_Divide
42000
43008
∴-------------------------------------------------- = 1024 × ------------------------ = --------------- = 1792
-----------A_Reference_Divide
27000000 27000 1125
Therefore, program A_Feedback_Divide = 1792 and A_Reference_Divide = 1125.
Note that n=1024 when programming a custom audio clock (see Section 3.9.2 on
page 73).
36655 - 2
April 2006
57 of 113
GS4911B/GS4910B Data Sheet
3.6.3 Adjustable Locking Time
The GS4911B/GS4910B offers two different locking mechanisms to allow the user
to control the PLL lock time and the integrity of the output signal during the locking
process. The locking process is said to take place after the application of the input
reference and before the LOCK_LOST signal is set LOW.
By default, the internal PLL will crash lock. This locking process will ensure a
minimum PLL locking time; however, crash lock will cause the phase of the output
clock and timing signals to jump during the locking process. The crash behaviour
of the video PLL is controlled by the Crash_Time bits of register address 24h.
Alternatively, the user may set bit 1 of register 16h HIGH to force the PLL to drift
lock. Drift lock will increase the locking time of the PLL, but will maintain the signal
integrity of the output clock and timing pulses during the locking process.
As discussed in Section 3.5.3 on page 47, the device will normally drift lock when
the reference is removed and subsequently re-applied during Genlock mode.
3.6.4 Adjustable Loop Bandwidth
The default loop bandwidth of the GS4911B/GS4910B's internal video PLL is 10Hz
when the output video standard is the same as the input reference format. For
other cross-locking combinations, the default loop bandwidth may be smaller than
1Hz or as large as 30Hz.
The user may adjust the loop bandwidth of both the video and audio PLLs to a
value that depends on the input, output, and audio standards selected, as well as
on the amplitude of the jitter present on the applied HSYNC signal. Increasing the
loop bandwidth will result in a shorter PLL lock time, but will allow more frequency
components of jitter to be passed to the outputs. Decreasing the loop bandwidth
will decrease the output jitter, but will result in a longer PLL lock time.
3.6.4.1 Loop Bandwidth of the Video PLL
The capacitive component of the filter controlling the video loop bandwidth is
determined by the Video_Cap_Genlock register and the resistive component is
determined by the Video_Res_Genlock register. These two registers are located
at addresses 26h and 27h, respectively, of the host interface.
To determine the setting of Video_Res_Genlock and Video_Cap_Genlock, the
following equations must be solved:
Video_Res_Genlock =
47 + log 2 ( 6 × BW × JITTERIN × H_Feedback_Divide )
Video_Cap_Genlock ≤ Video_Res_Genlock – 21
36655 - 2
April 2006
58 of 113
GS4911B/GS4910B Data Sheet
where:
BW = the desired video PLL loop bandwidth
JITTERIN = Jitter present on applied HSYNC reference signal, in seconds
H_Feedback_Divide = the numerator of the video PLL divide ratio
H_Feedback_Divide represents the numerator of the ratio of the output clock
frequency to the frequency of the H reference pulse. It is calculated as described
in Section 3.6.2.1 on page 54.
NOTE: The bandwidth calculation represented by the above equation is only
approximate. As the programmed value of Video_Res_Genlock becomes larger,
the approximation becomes more accurate.
For example, the following steps are necessary to program a loop bandwidth of
25Hz given the following conditions: input HSYNC jitter = 3 ns, VID_STD[5:0] = 3
and input reference format = NTSC.
1. Calculate H_Feedback_Divide (as defined in Section 3.6.2.1 on page 54):
H_Feedback_Divide f pclkout
-------------------------------------------------- × ----------------H_Reference_Divide f Hrefin
f pclkout = 27MHz
27
f Hrefin = ------------ MHz
1716
H_Feedback_Divide
1716
∴-------------------------------------------------- = 27 × ------------ = 1716
-----------H_Reference_Divide
27
1
Therefore, H_Feedback_Divide = 1716.
2. Calculate the value for Video_Res_Genlock:
Video_Res_Genlock =
–9
47 + log 2 ( 6 × 25 × ( 3 × 10 ) × 1716 )
= 37
3. Calculate the value for Video_Cap_Genlock:
Video_Cap_Genlock = 37 – 21 = 16
Therefore, program Video_Res_Genlock = 37 and Video_Cap_Genlock = 16.
NOTE: The value programmed in the Video_Res_Genlock register must be
between 32 and 42. The value programmed in the Video_Cap_Genlock register
must be greater than 10. These limits define the exact range of loop bandwidth
adjustment available.
36655 - 2
April 2006
59 of 113
GS4911B/GS4910B Data Sheet
3.6.4.2 Loop Bandwidth of the Audio PLL (GS4911B only)
The capacitive component of the filter controlling the audio loop bandwidth is
determined by the Audio_Cap_Genlock register and the resistive component is
determined by the Audio_Res_Genlock register. These two registers are located
at addresses 39h and 3Ah, respectively, of the host interface.
To determine the setting of Audio_Res_Genlock and Audio_Cap_Genlock, the
following equations must be solved:
Audio_Res_Genlock =
47 + log 2 ( 6 × BW × JITTERIN × A _Feedback_Divide )
Audio_Cap_Genlock ≤ Audio_Res_Genlock – 21
where:
BW = the desired audio PLL loop bandwidth
JITTERIN = Jitter present on output PCLK, in seconds.
A_Feedback_Divide = the numerator of the audio PLL divide ratio
A_Feedback_Divide is calculated in the same way as demonstrated in
Section 3.6.2.2 on page 56.
NOTE: The bandwidth calculation represented by the above equation is only
approximate. As the programmed value of Audio_Res_Genlock becomes larger,
the approximation becomes more accurate.
NOTE2: The value programmed in the Audio_Res_Genlock register must be
between 32 and 42. The value programmed in the Audio_Cap_Genlock register
must be greater than 10. These limits define the exact range of loop bandwidth
adjustment available.
3.6.5 Locking to Digital Timing from a Deserializer
As described in Section 3.4.1 on page 43, the GS4911B/GS4910B may be
genlocked to either an analog reference, such as a Black & Burst signal, or to an
SDI input via the digital H, V, and F blanking signals normally produced by a
deserializer. When locking to an SDI input, the user should consider the possibility
of a switch of the SDI signal upstream from the system.
If the GS4911B/GS4910B is locked to the digital H, V, and F blanking signals
produced by a deserializer, and the SDI input to the deserializer is switched such
that the phase of the H input changes abruptly, the REF_LOST output will remain
LOW and the GS4911B/GS4910B will not crash lock to the new H phase. Instead,
the clock and timing outputs will very slowly drift towards the new phase. During
this period of drift, the LOCK_LOST output will be LOW, even though the device is
not genlocked.
The user should clear the Run_Window bits [2:0] of register adress 24h to force the
device to crash lock should such a switch occur. This will cause the
36655 - 2
April 2006
60 of 113
GS4911B/GS4910B Data Sheet
GS4911B/GS4910B to crash lock whenever it sees a disturbance of the input H
signal.
NOTE: Any action that causes an abrupt phase change of the H input to the
GS4911B/GS4910B such that REF_LOST is not triggered will cause the device to
respond in the manner described above.
In addition to the slow drifting behaviour outlined above, there may also be a
random phase difference between the input VSYNC and output V Sync signals
occurring each time a switch in the SDI stream causes an abrupt phase change of
the H input to the GS4911B/GS4910B. This will only occur when attempting to lock
the "f/1.001" HD output standards to the 525-line SD input references standards,
or vice versa. For cases where the user must manually video genlock the device,
the problem will occur whenever the value programmed for H_Reference_Divide
(registers 2B-2Ah) is greater than 1. All line-based timing outputs are affected.
The only way to ensure a constant phase difference between the input VSYNC
signal and the line-based timing outputs is to reset the line-based counters after
such a switch occurs. This is acheived by toggling bit 15 of register address 83h in
the host interface. The device will then delay all line-based output timing signals by
ΔVsync lines relative to the input VSYNC reference, as described in NOTE 3 of
Section 3.2.1.1 on page 37.
3.7 Clock Synthesis
The clock synthesis circuit generates the video/graphics clocks based on the
VID_STD[5:0] pins and host register settings. In the GS4911B, the clock synthesis
circuit also generates the audio clock signals based on the ASR_SEL[2:0] pins and
host register settings.
The generated video and audio clocks may be further divided and are presented to
the application layer via pins PCLK1-PCLK3 and ACLK1-ACLK3 respectively.
3.7.1 Video Clock Synthesis
The programmable video clock generator is referenced to an internal crystal
oscillator and is responsible for generating the PCLK output signals.
The crystal oscillator requires an external 27MHz crystal connected to pins X1 and
X2, or can be driven at LVTTL levels from an external 27MHz source connected to
X1. These two configurations are shown in Figure 1-1.
A range of 8 different video sample clock rates and 13 different graphic display
clock rates may be selected using the VID_STD[5:0] pins of the device. Section 1.4
on page 20 lists the video and graphic formats available using the VID_STD[5:0]
pins. Once the device is powered up and an initial output format is selected using
VID_STD[5:0], the video clock rate may also be modified via the host interface (see
Section 3.9 on page 72).
If desired, the external VID_STD[5:0] pins may be ignored by setting bit 1 of the
Video_Control register, and the video standard may instead be selected via the
VID_STD[5:0] register of the host interface (see Section 3.12.3 on page 79).
36655 - 2
April 2006
61 of 113
GS4911B/GS4910B Data Sheet
Although the external VID_STD[5:0] pins will be ignored, they should not be left
floating.
NOTE: If VID_STD[5:0] is set to 62 on power-up, the video clock will run at a
frequency based on the internal default settings of the chip until the user programs
registers 20h to 23h. Please see Section 3.9 on page 72 for a detailed explanation
of custom clock generation.
Once the video clock has been generated, it will be presented to the application
layer via the PCLK1 to PCLK3 pins. By default, each of the 3 video clock outputs
will produce the generated fundamental clock frequency. However, it is possible to
select other rates for each PCLK output by programming the PCLK_Phase/Divide
registers beginning at address 2Ch of the host interface (see Section 3.12.3 on
page 79).
Each PCLK output may be individually programmed to provide one of the following:
•
PCLK fundamental frequency
•
Fundamental frequency /2
•
Fundamental frequency /4
When all six VID_STD[5:0] pins are set LOW, the video clocks will be disabled.
PCLK1 and PCLK2 will go LOW and PCLK3/PCLK3 will be high impedance.
NOTE: If the PCLK divider bits of registers 2Ch - 2Eh are set to enable a divide by
2 or divide by 4, the resultant divided clock will align with the falling edge of the
output H Sync timing signal either on its rising or falling edge.
The PCLK1 to PCLK3 outputs may also be individually delayed with respect to the
eight TIMING_OUT signals to allow for skew control downstream from the
GS4911B/GS4910B. Using the PCLK_Phase/Divide registers, the phase of each
clock may be delayed up to a nominal 10.3ns in 16 steps of approximately 700ps
each (Table 3-6). This delay is available in addition to the genlock timing offset
phase adjustment described in Section 3.2.1 on page 37.
Table 3-6: Video Clock Phase Adjustment Host Settings
PCLKn_Phase[3:0] Setting
0h
1h
2h
3h
4h
5h
6h
7h
8h
9h
Ah
Bh
Ch
Dh
Eh
Fh
Phase Increment (ns)
0
0.7
1.4
2.1
2.8
3.5
4.2
4.9
5.6
6.3
7.0
7.7
8.4
9.1
9.8
10.3
NOTES:
1. The phase increments listed above are nominal values.
2. The phase of PCLK is delayed relative to the TIMING_OUT pins.
Additionally, the current drive capability of PCLK1 and PCLK2 may be set high or
low using the PCLK_Phase/Divide registers. By default the current drive will be
low. It must be set high if the clock rate is greater than 100MHz.
36655 - 2
April 2006
62 of 113
GS4911B/GS4910B Data Sheet
3.7.2 Audio Clock Synthesis (GS4911B only)
The programmable audio clock generator is referenced to the internal PCLK signal
and is responsible for generating the ACLK output signals. Three audio clock
output pins, ACLK1 to ACLK3, are available to the application layer.
The fundamental sampling frequency, fs, is selected using the ASR_SEL[2:0] pins
as shown in Table 3-7. Once selected, the audio clock rate may be customized via
the host interface (see Section 3.9 on page 72).
If desired, the external ASR_SEL[2:0] pins may be ignored by setting bit 2 of the
Audio_Control register and the sampling frequency may instead be programmed
in the ASR_SEL[2:0] register of the host interface (see Section 3.12.3 on page 79).
Although the external ASR_SEL[2:0] pins will be ignored, they should not be left
floating.
Table 3-7: Audio Sample Rate Select
ASR_SEL[2:0]
Sampling Frequency (kHz)
000
Audio Clock Generation Disabled
001
32
010
44.1
011
48
100
96
101
Slow 32*
110
Slow 44.1*
111
Slow 48*
*Slow 32, 44.1, and 48 are available only when the video standard selected is 23.98, 29.97, or 59.94
frame rate based. They refer to 32kHz, 44.1kHz, or 48kHz multiplied by 1000/1001 to maintain the 1,
2, or 3 frame sequence normally associated with 24, 30, and 60 fps video.
When all three ASR_SEL[2:0] pins are set LOW, the audio clock outputs will be
high impedance. In this case, the application layer may continue to power the
AUD_PLL_VDD pin; however, to minimize noise and power consumption,
AUD_PLL_VDD may be grounded.
By default, after system reset, ACLK1 to ACLK3 will output clock signals at 256fs,
64fs, and fs respectively. Different division ratios for each output pin may be
selected by programming the ACLK_fs_Multiple registers beginning at address
3Fh of the host interface (see Section 3.12.3 on page 79). The encoding of this
register is shown in Table 3-8. Clock outputs of 512fs, 348fs, 256fs, 192fs, 128fs,
64fs, fs, and z bit are selectable on a pin by pin basis. The z bit will go HIGH for
one fs period every 192 fs periods. Its phase is not defined by any timing event in
the GS4911B, and so is arbitrary.
36655 - 2
April 2006
63 of 113
GS4911B/GS4910B Data Sheet
Table 3-8: Audio Clock Divider
ACLKn_fs_Multiple[3:0]
Audio Clock Frequency
000
fs
001
64fs
010
128fs
011
192fs*
100
256fs
101
384fs*
110
512fs**
111
z-bit
*This setting is only available when the enable_384fs bit of the Audio_Control register is HIGH.
**512fs clock will have a 33% duty cycle when the enable_384fs bit is HIGH and fs = 96kHz.
The fs signal on ACLK1-3 has an accurate 50% duty cycle, and can be used for
left/right definition, with the following exception: if fs = 96kHz and the user
configures the host interface such that one of the three ACLK pins is set to output
a clock signal at 192fs or 384fs, the 512fs clock will have a 33% duty cycle.
All audio clocks are initially reset on the rising edge of the AFS pulse, ensuring that
video to audio clock synchronization is correct. During normal operation, the audio
clock edge is allowed to drift slightly with respect to the AFS pulse. By default, the
audio clock will be reset directly by the AFS pulse if it drifts more than
approximately +/-0.1us from the rising edge of the AFS pulse. However, after
device reset, or after the application of a new input reference, the ACLK outputs
may sometimes be offset from the AFS pulse by up to several microseconds. The
offset will remain until the device is reset or the reference removed and re-applied.
The user may avoid this offset by minimizing the width of the AFS_Reset_Window
using bits 9-7 of register 31h for the duration of the audio PLL locking process.
Once the audio PLL is locked, bit 1 of register 1Fh will be set HIGH, and the
AFS_Reset_Window may be set as desired. See Table 3-9.
NOTE: To maintain correct audio clock frequencies for some VESA standards, the
window tolerance shown in Table 3-9 may have to be increased from its default
setting. In this case, set the AFS_Reset_Window register to 1XX.
36655 - 2
April 2006
64 of 113
GS4911B/GS4910B Data Sheet
Table 3-9: Encoding Scheme for AFS_Reset_Window
Window Tolerance (us)
AFS_Reset_Window
(address 31h)
fs = 32kHz
fs = 44.1kHz
fs = 48 kHz
fs = 96 kHz
(enable_384fs = 1)
fs = 96 kHz
(enable_384fs = 0)
000
0.044
0.033
0.030
0.030
0.044
001
0.084
0.062
0.057
0.057
0.084
010
(default)
0.166
0.121
0.112
0.112
0.166
011
0.329
0.239
0.220
0.220
0.329
1XX
0.654
0.475
0.437
0.437
0.654
NOTE: ‘X’ signifies ‘don’t care.’ The bit setting will be ignored.
3.7.2.1 Audio to Video Clock Phasing
The important aspect of the audio to video phase relates to the way in which the
AFS pulse is used to reset the audio clock dividers so as to line up the leading edge
of the audio clocks with the leading edge of the H Sync pulse on line 1 of the first
field in the audio frame sequence. The AFS pulse is further discussed in
Section 3.8.2 on page 68.
625i 50 Format
For the 48kHz sampling rate, the audio to video phase relationship for 625/50i
reference signals is provided by the device in accordance with the EBU
recommended practice R83-1996. The start of an audio frame (fs clock) will align
with the 50% point of the H sync input of line 1 of each video frame (+/- the
allowable drift specified in Table 3-9).
525i 59.94 Format
For 525/59.94 NTSC reference signals, the device will observe the 5-frame
phase-relationship inherent with this video standard, aligning the audio clocks with
the 50% point of the H sync input of line 1 on every fifth frame (+/- the allowable
drift specified in Table 3-9).
The number of audio sample clocks during a video frame is shown in Table 3-10
for 32, 44.1, and 48kHz audio sampling frequencies.
36655 - 2
April 2006
65 of 113
GS4911B/GS4910B Data Sheet
Table 3-10: Audio Sampling Frequency to Video Frame Rate Synchronization
Audio Samples per Video Frame
Audio Sample Rate (kHz)
24fps
25fps
29.97fps
30fps
50fps
59.94fps
60fps
32
4000/3
1280
16016/15
3200/3
640
8008/15
1600/3
44.1
3675/2
1764
147147/100
1470
882
147147/200
735
48
2000
1920
8008/5
1600
960
4004/5
800
* fps = frames per second.
The external 10FID input pin may be used to resynchronize other audio clock
frequencies, according to Table 3-10, by applying an active signal during the
reference HSYNC of line 1 of the appropriate video frame. Please see
Section 3.4.2 on page 44 for more details on the 10FID input pin.
In the case where 10FID is not present as a reference signal, the GS4911B will
automatically generate an AFS pulse appropriate to the format selected, and use
it to create an audio frame sequence.
Host Interface Control of AFS and 10FID
Alternatively, the user may program the device via the host interface to re-time the
audio frame sequence and 10 field-ID. Using register 1Ah, a pulse may be
generated to reset the AFS and/or 10FID dividers at the start of an output video
frame (see Section 3.12.3 on page 79).
If using the host interface to reset the AFS pulse, the device may be configured to
ignore the input 10FID reference pin. To disable the signal on the external 10FID
pin from resetting the AFS output pulse, set bit 0 of the Audio_Control register
HIGH.
If using the host interface to reset the 10FID pulse, the external 10FID pin must be
grounded.
36655 - 2
April 2006
66 of 113
GS4911B/GS4910B Data Sheet
3.8 Video Timing Generator
The internal PCLK signal generated by the clock synthesis circuit is used to
produce horizontal, vertical, and frame based timing output signals.
The signals generated and available to the application layer via the TIMING_OUT
pins are: H Sync, H Blanking, V Sync, V Blanking, F Sync, F Digital, DE, 10FID,
AFS (GS4911B only), and USER_1~4. These signals are defined in Section 1.5 on
page 25. Additional information pertaining to the 10FID, AFS, and USER_1~4
signals can be found in the sub-sections below.
When the GS4911B/GS4910B is operating in Genlock mode, the H, V, and F
based output timing signals are synchronized to the H, V, and F reference signals
applied to the inputs by the application layer. The video timing outputs may be
offset from the input reference by programming the Genlock Offset registers
beginning at address 1Bh of the host interface (see Section 3.2.1.1 on page 37).
All TIMING_OUT signals have selectable polarity. The default polarities for each
signal are given in the descriptions in Section 1.5 on page 25.
3.8.1 10 Field ID Pulse
As described in Table 1-3, the 10 field ID (10FID) output signal is used in the
identification of film to video cadence. It is only generated for 29.97, 30, 59.94, and
60fps formats.
The 10FID pulse is generated on every 5th frame for 29.97 and 30fps formats, and
every 10th frame on 59.94 and 60fps formats.
By default, the 10FID signal is set HIGH on the leading edge of the H Sync output
for the duration of line 1 of field 1 at the start of the 10 field sequence. This is shown
in Figure 3-8.
Alternatively, by setting bit 4 of the Video_Control register at address 4Ch of the
host interface, the 10FID output signal may be configured to go HIGH (default
polarity) on the leading edge of the H Sync pulse of line 1 of the first field in the 10
field sequence, and be reset LOW on the leading edge of the H Sync pulse of line
1 of the second field in the 10 field sequence. This is shown in Figure 3-9.
Total Line
10FID Output
Line 1, Frame 1 every 'n' frames
Horizontal Sync Output
Line 1 every n frames where:
n = 5 @ 29.97 fps, 30 fps
n = 10 @ 59.94 fps, 60 fps
Figure 3-8: Default 10FID Output Timing
36655 - 2
April 2006
67 of 113
GS4911B/GS4910B Data Sheet
Total Field
10FID Output
Horizontal Sync Output
Line 1 every n frames where:
n = 5 @ 29.97 fps, 30 fps
n = 10 @ 59.94 fps, 60 fps
Figure 3-9: Optional 10FID Output Timing
The phasing of the divide by n frame counter may be reset by an external pulse on
the 10FID input pin, or via register 1Ah of the host interface (see Section 3.12.3 on
page 79).
NOTE: If a 10FID input signal is not provided to the device, the 10FID output signal
will be invalid until the user initiates a reset via the host interface. The user should
also reset the 10FID signal via the host if at any time the H input reference signal
is removed and then re-applied.
3.8.2 Audio Frame Synchronizing Pulse (GS4911B only)
As described in Table 1-3, the audio frame synchronizing (AFS) pulse identifies the
frame, within an n frame sequence, in which the audio sample rate clock is aligned
with the H Sync of line 1. It is generated for all video formats.
The leading edge of the AFS output pulse is co-timed with the H Sync
corresponding to line 1 of every nth frame in the sequence, and therefore identifies
the exact time at which the audio sample rate clock and video PCLK have
synchronous leading edges.
The number of frames in the sequence, n, is determined by the video frame rate
and the audio clock frequency. These are selected using the VID_STD[5:0] and
ASR_SEL[2:0] pins or via the host interface.
By default, the AFS pulse is 1 line long, as shown in Figure 3-10. Alternatively, by
setting bit 1 of the Audio_Control register, the AFS output signal may be configured
to go HIGH on the leading edge of the H Sync pulse of line 1 of the first field in the
‘n’ frame sequence, and be reset LOW on the leading edge of the H Sync pulse of
line 1 of the second field in the sequence. The AFS timing in this configuration is
similar to the 10FID optional timing shown in Figure 3-9.
36655 - 2
April 2006
68 of 113
GS4911B/GS4910B Data Sheet
Total Line
AFS_OUT
Horizontal Sync Output
Line 1 every n frames where:
n = 1 @ 25fps: fs = 32kHz
n = 1 @ 25fps, 30fps & 60fps: fs = 44.1kHz
n = 1 @ 25fps, 30fps & 60fps; fs = 48kHz
n = 2 @ 24fps; fs = 44.1kHz, 48kHz
n = 3 @ 24fps, 30fps & 60fps: fs = 32kHz
n = 5 @ 29.97fps & 59.94fps; fs = 48kHz
n = 15 @ 29.97fps & 59.94fps; fs = 32kHz
n = 100 @ 29.97fps; fs = 44.1kHz
n = 200 @ 59.94fps; fs = 44.1kHz
Figure 3-10: AFS Output Timing
The phasing of the divide by n counter can be controlled by the 10FID input or via
designated registers in the host interface.
By default, the 10FID input pin controls the AFS phase (in addition to controlling
the 10FID phase); however, this feature may be disabled by setting bit 0 of the
Audio_Control register (see Section 3.12.3 on page 79). In addition, the AFS signal
may be reset via register 1Ah.
3.8.3 USER_1~4
As described in Table 1-3, the GS4911B/GS4910B offers 4 user programmable
output signals which are available independent of the selected output video format.
Each user signal is individually programmable and the polarity, position, and width
of each output may be defined with respect to the digital output timingof the device.
Each output signal may be programmed in both the horizontal and vertical
dimensions relative to the leading edges of H blanking and V blanking. If desired,
the pulses produced may then be combined with a logical AND, OR, or XOR
function to produce a composite signal (for example, a horizontal back porch pulse
during active lines only, or the active part of lines 15 through 20 for vertical
information retrieval).
By default, the AND, OR, and XOR functions are disabled. Therefore, when a
USER signal is selected using the Output_Select registers of the host interface, the
signal will go LOW (default polarity) at the H_Start pixel and return HIGH after the
H_Stop pixel. Setting the AND bit HIGH, for example, will cause the USER signal
to be active only when USER_H is active and USER_V is active (i.e. the pixel is
between both H_Start and H_Stop and V_Start and V_Stop). See Figure 3-11.
NOTE: The effective horizontal range of the four user-defined timing signals is
[H_Start + 1, H_Stop], except when H_Start = 1, in which case the range is
[H_Start, H_Stop]. This prevents the user from specifying an output USER signal
that begins on pixel 2 of a line.
36655 - 2
April 2006
69 of 113
GS4911B/GS4910B Data Sheet
In the case of interlaced output formats, the programmed vertical start and stop
lines refer to the start and stop lines of the generated USER signal on field 1. The
start and stop lines of the USER signal on the even fields will be V_Start - 1 and
V_Stop - 1, respectively.
For example, if VID_STD[5:0] = 3, field 1 will have 263 lines and field 2 will have
262 lines. A user-defined vertical pulse programmed to start on line 12 and stop on
line 17 will start on frame lines 12 and 274, and stop on frame lines 17 and 279.
V_Start
V_Start
V_Stop
V_Stop
H_Start
V_Start
V_Start
V_Stop
V_Stop
H_Stop
AND=1
H_Stop
H_Start
AND=0, OR=0, XOR=0 (default)
AND=0, OR=1
H_Stop
H_Start
H_Stop
H_Start
The designated registers for programming each user signal are located in the host
interface beginning at address 57h. See Section 3.12.3 on page 79.
AND=0, OR=0, XOR=1
Shading indicates when USER_x signal is active
Figure 3-11: USER Programmable Output Signal
36655 - 2
April 2006
70 of 113
GS4911B/GS4910B Data Sheet
3.8.4 TIMING_OUT Pins
The horizontal, vertical, and frame based timing output signals for the selected
video format are available to the application layer via the TIMING_OUT_1 to
TIMING_OUT_8 pins.
Programmable Crosspoint Switch
Each TIMING_OUT pin outputs a default signal as shown in Table 1-3.
Alternatively, a crosspoint switch may be programmed via the eight Output_Select
registers of the host interface, allowing the user to select which output signal is
directed to each TIMING_OUT pin (see Section 3.12.3 on page 79). Any signal
may be sent to more than one pin if desired.
Table 3-11 outlines the encoding scheme of the eight Output_Select registers,
which begin at address 43h of the host interface.
Table 3-11: Crosspoint Select
Output_Select_n Bit Settings
Output Signal
0000
High Impedance
0001
H Sync
0010
H Blanking
0011
V Sync
0100
V Blanking
0101
F Sync
0110
F Digital
0111
10FID
1000
DE
1001
Reserved
1010
AFS*
1011
USER_1
1100
USER_2
1101
USER_3
1110
USER_4
1111
Reserved
*AFS is only available on the GS4911B. The bit setting 1010b will be ignored by the GS4910B.
3.8.4.1 Selectable Current Drive and Polarity
The current-drive of each timing output pin is also selectable via the Output_Select
registers. The current drive of each TIMING_OUT pin is low by default. However,
it may be set high to accommodate certain applications.
Additionally, the Polarity register of the host interface may be programmed to select
the polarity of each timing output signal.
36655 - 2
April 2006
71 of 113
GS4911B/GS4910B Data Sheet
3.9 Custom Clock Generation
In addition to the device’s pre-programmed clock frequencies, the user may
generate a custom audio or video clock by programming designated registers in
the host interface.
Custom video clock generation is supported by both the GS4910B and GS4911B
and is described in Section 3.9.1 on page 72. Custom audio clock generation is
only supported by the GS4911B and is described in Section 3.9.2 on page 73.
3.9.1 Programming a Custom Video Clock
The fundamental frequency of the video clock is defined by the output video format
initially set by VID_STD[5:0]. At any time, this fundamental frequency may be
modified to create a custom output video format.
The user may generate a video clock with any frequency between 13.5MHz and
165MHz. By programming the PCLK_Divide registers, the output PCLK may be as
low as 13.5/4 = 3.375MHz.
Generating a custom video clock will change the period of the video timing signals
presented to the TIMING_OUT pins; however, the pixels per line, lines per frame,
and other pixel and line-based timing signals will remain unchanged. To redefine
the pixel and line based timing parameters, registers 4Eh to 55h must be
reprogrammed as described in Section 3.10 on page 74.
The frequency of the custom video clock is determined using a ratio based on the
27MHz reference. Therefore, to program a custom clock, the user must calculate
and program the set of integers (Nv, Dv) in the equation:
f out
N
-----v- = ------Dv
f in
where:
fout = desired output video clock frequency
fin = 27MHz crystal reference
Nv = numerator of the ratio (host register 20h-21h)
Dv = denominator of the ratio (host register 22h-23h)
Before programming Nv and Dv, the numerator and denominator must be reduced
to their lowest factors. Two examples are given below:
Example 1: Programming an output video clock of 74.25MHz:
f out
-------- = 74.25MHz
-------------------------f in
27MHz
Nv
∴------ = 7425
------------ = 11
-----Dv
2700
4
Therefore, program Nv = 11 and Dv = 4.
36655 - 2
April 2006
72 of 113
GS4911B/GS4910B Data Sheet
Example 2: Programming an output video clock of 74.175824MHz (74.25/1.001):
74.25
------------- MHz
f out
1.001
-------- = ------------------------f in
27MHz
Nv
7425 × 1000
250
∴------ = ------------------------------ = --------Dv
2700 × 1001
91
Therefore, program Nv = 250 and Dv = 91.
NOTE: The Nv and Dv values programmed in registers 20h-21h and 22h-23h are
not held until the custom video clock update bit (6) of register 16h is toggled.
3.9.2 Programming a Custom Audio Clock (GS4911B only)
The GS4911B’s audio clocks are derived from the fundamental audio sampling
frequency initially set by ASR_SEL[2:0]. At any time this fundamental sampling
frequency may be modified to create a custom output audio clock.
The user may generate any audio sampling frequency between 6.6kHz and 96kHz,
and therefore create a custom audio clock as high as 512*96kHz. When generating
a custom audio sampling frequency, ASR_SEL[2:0] must be set to 100b and bit 5
of register 31h (enable_384fs) must be kept LOW.
The fundamental sampling frequency is determined using a ratio based on the
27MHz reference. Therefore, to program a custom audio clock, the user must
calculate and program the set of integers (Na, Da) in the equation:
fs
N
------a = 1024 × ----f in
Da
where:
fs = desired fundamental audio sampling frequency
fin = 27MHz crystal reference
Na = numerator of the ratio (host register 33h-34h)
Da = denominator of the ratio (host register 35h-36h)
Before programming Na and Da, the numerator and denominator must be reduced
to their lowest factors.
For example, to program a fundamental audio sampling frequency of 42kHz:
N
42000
------a = 1024 × ------------------------ = 43008
--------------- = 1792
-----------27000000
Da
27000
1125
Therefore, program Na = 1792 and Da = 1125 and toggle the custom audio clock
update bit (6) of register 31h. Using registers 3Fh to 41h, the custom audio
sampling frequency generated may then be multiplied by a factor of 64, 128, 256,
or 512 before being presented to the ACLK pins.
NOTE: The AFS reset described in Section 3.7.2 on page 63 will always remain
active.
36655 - 2
April 2006
73 of 113
GS4911B/GS4910B Data Sheet
3.10 Custom Output Timing Signal Generation
In addition to the devices’s pre-programmed output timing signals, the user may
also build their own custom timing signals. This is achieved by setting
VID_STD[5:0] = 62 and programming designated host registers.
When programming custom output timing signals, the user must define the pixel,
line, and field/frame timing parameters using registers 4Eh to 55h of the host
interface (see Figure 3-12). For all custom formats, the VSync output will start on
line 1 of the video field. The user may delay the VSync pulse to any line using the
V_Offset register (see Section 3.2.1.1).
When the user sets VID_STD[5:0] = 62, registers 4Eh to 55h will become
read/write configurable and the device will initially continue to output timing signals
based on the video format previously selected. Once the user has programmed all
eight custom timing registers, generation of the new timing signals will begin.
The frequency of the video clock will remain as previously selected unless
otherwise modified as described in Section 3.9.1 on page 72.
NOTE: If VID_STD[5:0] = 62 on power-up, the initial output timing signals will be
set to the internal default timing of the chip until the user programs 4Eh to 55h.
Clocks_Per_Line (4Eh)
H Sync
Clocks_Per_Hsync (4Fh)
Hsync_To_EAV (51h)
H Blanking
Hsync_To_SAV (50h)
Lines_Per_Field (52h)
V Sync
Lines_Per_Vsync (53h)
Vsync_To_Last_Active_Line (55h)
V Blanking
Vsync_To_First_Active_Line (54h)
Figure 3-12: Custom Timing Parameters
3.10.1 Custom Input Reference
As explained in Section 3.5.2 on page 45, when VID_STD[5:0] = 62, the device will
only verify that a stable signal with a period of less than 2.4ms is present on the
HSYNC input pin before attempting to genlock. Therefore, in addition to
programming custom output timing signals, the user may genlock the output timing
signals to a custom reference pulse applied to HSYNC. In this case the user is
required to manually program the video genlock block (see Section 3.6.2.1 on
page 54).
36655 - 2
April 2006
74 of 113
GS4911B/GS4910B Data Sheet
3.11 Extended Audio Mode for HD Demux using the Gennum Audio
Core
The GS4911B/GS4910B has been designed to interface with Gennum's FPGA
Audio Core in order to provide a 24.576MHz clock (512 * 48kHz) locked to the
audio clock contained in the embedded audio data packets of an HD-SDI stream.
It is the responsibility of the user to divide this clock by 4 to obtain the 6.144MHz
required by the core.
In HD Demux mode, the FPGA Audio Core will extract an audio clock from the
embedded audio data packets and present a 24kHz clock to the
GS4911B/GS4910B via the aclkdiv2a (for Group A) and aclkdiv2b (for Group B)
outputs. The embedded clock must be 48kHz.
The 24kHz reference signals for each audio group must be applied to the HSYNC
input pin of a GS4911B/GS4910B, while a divided version of this signal must be
applied to the VSYNC input pin. The divided signal must meet the requirements for
VSYNC validity given in Section 3.5.2 on page 45. It is recommended that the
VSYNC signal be generated by dividing the 24kHz reference applied to HSYNC by
512 to give 46.875Hz.
To enable the extended audio mode, the user must do the following:
1. Set VID_STD[5:0] = 04h.
2. Set the F_Lock_Mask and V_Lock_Mask bits [4:3] of register address 16h to
1.
3. Set the Ext_Audio_Mode register address 81h to 20C1h.
4. Toggle the Update_Custom_V_Clock bit [6] of register address 16h.
In this mode, the GS4911B/GS4910B will produce a 24.576MHz clock on its PCLK
output pins that is locked to the 24kHz extracted audio clock reference applied to
HSYNC. It will not lock to any other reference frequency. The user may then divide
this frequency by 4 using the programmable dividers in the GS4911B/GS4910B.
FPGA
Serial
Video
Input
Video Data
GS1559
Deserializer
PCLK
vin[19:0]
aclk64a
wclka
pclk
aout1_2
aout3_4
/512
/512
GS49xxB
PCLK1
aclk128a
HD AUDIO
DEMUX CORE
aclk64b
wclkb
aout5_6
GS49xxB
PCLK1
aclk128b
aout7_8
aclkdiv2b
aclkdiv2a
Figure 3-13: Audio Clock Block Diagram for HD Demux Operation
36655 - 2
April 2006
75 of 113
GS4911B/GS4910B Data Sheet
3.12 GSPI Host Interface
The GSPI, or Gennum Serial Peripheral Interface, is a 4-wire interface provided to
allow the host to enable additional features of the GS4911B/GS4910B and/or to
provide additional status information through configuration registers in the device.
The GSPI comprises a serial data input signal, SDIN, a serial data output signal,
SDOUT, an active low chip select, CS, and a burst clock, SCLK. The burst clock
must have a duty cycle between 40% and 60%.
Because these pins are shared with the JTAG interface port, an additional control
signal pin, JTAG/HOST is provided. When JTAG/HOST is LOW, the GSPI
interface is enabled.
When operating in GSPI mode, the SCLK, SDIN, and CS signals are provided by
the application interface. The SDOUT pin is a non-clocked loop-through of SDIN
and may be connected to the SDIN pin of another device, allowing multiple devices
to be connected to the GSPI chain. The interface is illustrated in Figure 3-14.
Application Host
GS4911B/GS4910B
SCLK
CS1
SDOUT
SCLK
CS
SDIN
SDOUT
GS4911B/GS4910B
SCLK
CS2
CS
SDIN
SDIN
SDOUT
Figure 3-14: GSPI Application Interface Connection
All read or write access to the GS4911B/GS4910B is initiated and terminated by
the host processor. Each access always begins with a 16-bit command word on
SDIN indicating the address of the register of interest. This is followed by a 16-bit
data word on SDIN in write mode, or a 16-bit data word on SDOUT in read mode.
36655 - 2
April 2006
76 of 113
GS4911B/GS4910B Data Sheet
3.12.1 Command Word Description
The command word consists of 16 bits transmitted MSB first and includes a
read/write bit, an Auto-Increment bit and a 12-bit address. Figure 3-15 shows the
command word format and bit configurations.
Command words are clocked into the GS4911B/GS4910B on the rising edge of the
serial clock, SCLK, which operates in a burst fashion.
When the Auto-Increment bit is set LOW, each command word must be followed
by only one data word to ensure proper operation. If the Auto-Increment bit is set
HIGH, the following data word will be written into the address specified in the
command word, and subsequent data words will be written into incremental
addresses. This facilitates multiple address writes without sending a command
word for each data word.
Auto-Increment may be used for both read and write access.
MSB
R/W RSV
LSB
RSV
AutoInc
A11
A10
RSV = Reserved. Must be set to zero.
A9
A8
A7
A6
A5
A4
A3
A2
A1
D3
D2
D1
A0
R/W: Read command when R/W = 1
Write command when R/W = 0
Figure 3-15: Command Word Format
MSB
D15
LSB
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D0
Figure 3-16: Data Word Format
3.12.2 Data Read and Write Timing
Read and write mode timing for the GSPI interface is shown in Figure 3-17 and
Figure 3-18 respectively. The timing parameters are defined in Table 3-12.
When several devices are connected to the GSPI chain, only one CS should be
asserted during a read sequence.
During the write sequence, all command and following data words input at the
SDIN pin are output at the SDOUT pin as is. Where several devices are connected
to the GSPI chain, data can be written simultaneously to all the devices that have
CS set LOW.
36655 - 2
April 2006
77 of 113
GS4911B/GS4910B Data Sheet
Table 3-12: GSPI Timing Parameters
Parameter
Definition
Specification
t0
The minimum duration of time chip select, CS, must be
LOW before the first SCLK rising edge.
1.5 ns
t1
The minimum SCLK period.
100 ns
t2
Duty cycle tolerated by SCLK.
40% to 60%
t3
Minimum input setup time.
1.5 ns
t4
The minimum duration of time between the last SCLK
command word (or data word if the Auto-Increment bit is
HIGH) and the first SCLK of the data word (write cycle).
37.1 ns
t5
The minimum duration of time between the last SCLK
command word (or data word if the Auto-Increment bit is
HIGH) and the first SCLK of the data word (read cycle).
148.4 ns
t6
Minimum output hold time (15pF load).
1.5 ns
t7
The minimum duration of time between the last SCLK of
the GSPI transaction and when CS can be set HIGH.
37.1 ns
t8
Minimum input hold time.
1.5 ns
t5
SCLK
t6
CS
SDIN
R/W
RSV
RSV
AutoInc
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
SDOUT
R/W
RSV
RSV
AutoInc
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
D14
D15
D12
D13
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Figure 3-17: GSPI Read Mode Timing
t0
t7
t4
t1
SCLK
t3
CS
t2
t8
SDIN
R/W
RSV
RSV
AutoInc
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
SDOUT
R/W
RSV
RSV
AutoInc
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Figure 3-18: GSPI Write Mode Timing
36655 - 2
April 2006
78 of 113
GS4911B/GS4910B Data Sheet
3.12.3 Configuration and Status Registers
Table 3-13 summarizes the GS4911B/GS4910B's internal status and configuration
registers.
All registers are available to the host via the GSPI and are all individually
addressable.
Table 3-13: Configuration and Status Registers
Register Name
Address
Bit
Description
R/W
Default
RSVD
00h - 09h
–
Reserved.
–
–
H_Period
0Ah
15-0
Contains the number of 27MHz pulses in the input H
Sync period. This register is set by the Reference
Format Detector block using the H Sync signal present
on the external HSYNC input pin.
R
N/A
R
N/A
R
N/A
R
N/A
R
N/A
NOTE: If the reference is removed this register will
remain unchanged until a new reference with a different
HSYNC period is applied.
Reference: Section 3.5.1 on page 45
H_16_Period
0Bh
15-0
Contains the number of 27MHz pulses in 16 H Sync
periods. This register is set by the Reference Format
Detector block using the H Sync signal present on the
external HSYNC input pin. It is useful for 1/1.001 data
detection.
NOTE: If the reference is removed this register will
remain unchanged until a new reference with a different
HSYNC period is applied.
Reference: Section 3.5.1 on page 45
V_Lines
0Ch
15-0
Contains the number of H Sync periods in the input V
Sync interval. This register is set by the Reference
Format Detector block using the signals present on the
external HSYNC and VSYNC input pins.
NOTE: If the reference is removed this register will
remain unchanged until a new reference with a different
VSYNC period is applied.
Reference: Section 3.5.1 on page 45
V_2_Lines
0Dh
15-0
Contains the number of H Sync periods in 2 V Sync
intervals. This register is set by the Reference Format
Detector block using the signals present on the external
HSYNC and VSYNC input pins.
NOTE: If the reference is removed this register will
remain unchanged until a new reference with a different
VSYNC period is applied.
Reference: Section 3.5.1 on page 45
F_Lines
0Eh
15-0
Contains the number of H Sync periods in the input F
Sync interval. This register is set by the Reference
Format Detector block using the signals present on the
external HSYNC and FSYNC input pins.
NOTE: If the reference is removed this register will
remain unchanged until a new reference is applied. If
the new reference does not include an FSYNC pulse,
this register will be set to zero.
Reference: Section 3.5.1 on page 45
36655 - 2
April 2006
79 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Input_Standard
0Fh
15-13
Reserved. Set these bits to zero when writing to 0Fh.
–
–
0Fh
12
Force_Input - Set this bit HIGH to force the
GS4911B/GS4910B to recognize the applied input
reference format as the standard programmed in bits
11-6 of this register.
R/W
0
R/W
0
R/W
N/A
Reference: Section 3.2.1.2 on page 40
0Fh
11-6
Forced_Standard - When bit 12 is set HIGH, the
GS4911B/GS4910B will use the value programmed in
these bits, rather than the value in bits 5-0, to determine
the input reference format. The 6-bit value programmed
here should always correspond to the VID_STD[5:0]
value of the applied reference.
These bits should only be programmed as part of the
Freeze mode procedure described in Section 3.2.1.2 on
page 40.
0Fh
5-0
Detected_Standard - Contains the video standard
applied to the input reference pins once it has been
detected. These bits are set by the Reference Format
Detector block and correspond to the VID_STD[5:0]
value of the standard as listed in Table 1-2.
The Detected_Standard bits will be set to zero if no input
reference signal is applied or if the input reference
signal is not an automatically recognized video format.
Otherwise the value will be between 1 and 54.
Reference: Section 3.5.2 on page 45
Amb_Std_Sel
10h
15-11
Reserved. Set these bits to zero when writing to 10h.
–
–
10h
10-0
The user may set this register to distinguish between
different formats that look identical to the internal
Reference Format Detector block. See Table 3-2.
R/W
0
R/W
0
Reference: Section 3.5.2.1 on page 46
Reference_Standard_Disable
14h-11h
63-0
The Reference_Standard_Disable registers may be
used to disable one or more of the recognized input
standards from being used to genlock the output. This is
done by setting the bit HIGH that corresponds to the
VID_STD[5:0] value of the video standard in Table 1-2.
For example, if bit 5 is set HIGH, then the output clock
and timing signals will not genlock to an input reference
with timing corresponding to VID_STD[5:0] = 5 in
Table 1-2.
Address 11h = bits 15-0
Address 12h = bits 31-16
Address 13h = bits 47-32
Address 14h = bits 63-48
Reference: Section 3.6 on page 50
36655 - 2
April 2006
80 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Genlock_Status
15h
15-6
Reserved.
–
–
15h
5
Reference_Lock - this bit will be HIGH when the output
is successfully genlocked to the input (i.e. when bits 4-1
of this register are HIGH and are not masked by bits 4-2
of register 16h).
R
N/A
R
N/A
R
N/A
R
N/A
R
N/A
R
N/A
The LOCK_LOST output pin is an inverted copy of this
bit.
Reference: Section 3.6.1 on page 50
15h
4
F_Lock - this bit will be HIGH when the output F is
successfully genlocked to the FSYNC input.
NOTE: If the input reference does not include an
FSYNC input, this bit will have the same setting as
V_Lock (bit 3).
Reference: Section 3.6.1 on page 50
15h
3
V_Lock - this bit will be HIGH when the output V is
successfully genlocked to the VSYNC input.
Reference: Section 3.6.1 on page 50
15h
2
H_Lock - this bit will be HIGH when the output H is
successfully genlocked to the HSYNC input.
Reference: Section 3.6.1 on page 50
15h
1
Clock_Lock - this bit will be HIGH when the video clock
is locked to the internal V_pll AND the audio clock is
locked to the internal A_pll (i.e. bits 0 and 1 of register
1Fh are HIGH).
Reference: Section 3.6.1 on page 50
15h
0
Reference_Present - this bit will be HIGH when a valid
input reference signal has been applied to the device.
The REF_LOST output pin is an inverted copy of this
bit.
Reference: Section 3.5.2 on page 45
36655 - 2
April 2006
81 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Genlock_Control
16h
15-7
Reserved. Set these bits to zero when writing to 16h.
–
–
16h
6
Update_Custom_V_Clock - this bit is used to update the
custom video clock parameters programmed in registers
20h to 23h of the host interface. All non-zero
parameters in these registers will be updated via a LOW
to HIGH transition on this bit.
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
–
This bit is also used to enable the Extended Audio Mode
of the device.
16h
5
Genlock_From_Host - set this bit HIGH to enable video
genlock control via the Host Interface instead of the
external GENLOCK pin (see bit 0 of this register).
Reference: Section 3.2 on page 36
16h
4
F_Lock_Mask - if this bit is set HIGH, the
GS4911B/GS4910B will ignore the status of F_Lock (bit
4 of register 15h) when determining the status of
Reference_Lock (bit 5 of register 15h).
Reference: Section 3.6.1 on page 50
16h
3
V_Lock_Mask - if this bit is set HIGH, the
GS4911B/GS4910B will ignore the status of V_Lock (bit
3 of register 15h) when determining the status of
Reference_Lock (bit 5 of register 15h).
Reference: Section 3.6.1 on page 50
16h
2
H_Lock_Mask - if this bit is set HIGH, the
GS4911B/GS4910B will ignore the status of H_Lock (bit
2 of register 15h) when determining the status of
Reference_Lock (bit 5 of register 15h).
Reference: Section 3.6.1 on page 50
16h
1
Drift_Crash - when this bit is set HIGH, the generated
video clock will drift lock to a new input reference rather
than crash lock.
Reference: Section 3.6.3 on page 58
16h
0
GENLOCK - this bit may be used instead of the external
pin to Genlock the output video format to the input
reference. This bit will be ignored if bit 5 of this register
is LOW.
Reference: Section 3.2 on page 36
Output_H_Reset
17h
15-0
When the output is genlocked to the input, the input
reference is used to reset the line-based counter
controlling the generated timing output signals.
Programming this register to a non-zero value will
over-ride the internal pixel-based counter. The counter
reset will occur every Output_H_Reset lines instead of
on a frame basis.
This register is programmed when manually
programming the internal video genlock block.
The default value of this register will vary depending on
the output video standard selected.
Reference: Section 3.6.2 on page 54
36655 - 2
April 2006
82 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Output_FV_Reset
18h
15-0
When the output is genlocked to the input, the input
reference is used to reset the frame-based counter
controlling the generated timing output signals.
R/W
–
Programming this register to a non-zero value will
over-ride the internal frame-based counter. The counter
reset will occur every Output_FV_Reset input frames.
This register is programmed when manually
programming the internal video genlock block.
NOTE: Once this register is programmed, it must be
updated using register 19h.
The default value of this register will vary depending on
the output video standard selected.
Reference: Section 3.6.2 on page 54
Frame_Divider_Reset
19h
15-2
Reserved. Set these bits to zero when writing to 19h.
–
–
19h
1
Ref_F_Sync - when Ref_F_Mode (bit 0 of 19h) is set
HIGH, this bit is used to initialize the frame-based
counter reset programmed in 18h.
R/W
0
R/W
0
The reset pulse is generated if this bit is pulsed (LOW to
HIGH to LOW) during the output frame immediately
prior to the frame the reset is to occur.
This register is programmed when manually
programming the internal video genlock block.
Reference: Section 3.6.2 on page 54
19h
0
Ref_F_Mode - set this bit HIGH to initialize the
frame-based reset via the host interface (using bit 1
above).
Reference: Section 3.6.2 on page 54
36655 - 2
April 2006
83 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
10FID_AFS_Reset
1Ah
15-4
Reserved. Set these bits to zero when writing to 1Ah.
–
–
1Ah
3
AFS_Reset (GS4911B only) - set this bit HIGH to use
Reset_Sync (bit 0 of register 1Ah) to reset the output
AFS pulse.
R/W
0
R/W
0
NOTE: This bit will remain LOW in the GS4910B. Set
this bit LOW when writing to address 1Ah of the
GS4910B.
Reference: Section 3.7.2.1 on page 65
1Ah
2
10FID_Reset - set this bit HIGH to use Reset_Sync (bit
0 of register 1Ah) to reset the output 10FID pulse.
NOTE: If a 10FID input signal is not provided to the
device, the user must generate a reset using this bit to
initiate the 10FID timing output. In this case, the 10FID
input pin must be grounded.
Reference: Section 3.7.2.1 on page 65
1Ah
1
Reserved. Set this bit to zero when writing to 1Ah.
–
–
1Ah
0
Reset_Sync - resets the pulses described in bits 2, and
3 above.
R/W
0
R/W
0
R/W
0
The reset pulse is generated if this bit is pulsed (LOW to
HIGH to LOW) during the output frame immediately
prior to the frame the reset is to occur. This reset will
operate independently of any other resets, for example
from the reference input.
H_Offset
1Bh
15-0
The output H signal may be delayed with respect to the
input reference by the number of pixels programmed in
this register. (See Section 3.2.1.1 on page 37).
The value programmed in this register should not
exceed the maximum number of clock periods per line
of the outgoing standard. Horizontal advances may be
achieved by programming a value equal to the
maximum allowable offset minus the desired advance.
NOTE: This register is internally read by the device
once per field. At that time any new value programmed
is sent to the internal offset circuitry.
Reference: Section 3.2.1.1 on page 37
V_Offset
1Ch
15-0
The output V signal may be delayed with respect to the
input reference by the number of lines programmed in
this register. (See Section 3.2.1.1 on page 37).
The value programmed in this register should not
exceed the maximum number of lines per frame of the
outgoing standard. Vertical advances may be achieved
by programming a value equal to the maximum
allowable offset minus the desired advance.
NOTE: This register is internally read by the device
once per field. At that time any new value programmed
is sent to the internal offset circuitry.
Reference: Section 3.2.1.1 on page 37
36655 - 2
April 2006
84 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Clock_Phase_Offset
1Dh
15-0
Phase_Offset - The output clock and data phase may
be offset with respect to the input reference by the
number of increments programmed in this register. The
increment step size depends on the video clock
frequency.
R/W
0
R/W
000Bh
The encoding scheme for this register is shown in
Table 3-1.
NOTE: This register must be cleared to achieve a clock
phase offset of zero.
Reference: Section 3.2.1.1 on page 37
Max_Ref_Delta
1Eh
15-0
The value programmed in this register controls the
allowed deviance from the expected frequency on the
reference HSYNC before the internal video PLL loses
lock. The encoding scheme is shown in Table 3-3.
Reference: Section 3.5.4 on page 49
Video_Status
1Fh
15-5
Reserved.
–
–
1Fh
4
Ref_H_Polarity - status register to indicate the detected
H Sync polarity ('1' for positive, '0' for negative).
R
N/A
R
N/A
R
N/A
R
N/A
R
N/A
This bit will be zero when no reference signal is present.
Reference: Section 3.4.3 on page 45
1Fh
3
Ref_V_Polarity - status register to indicate the detected
V Sync polarity ('1' for positive, '0' for negative).
This bit will be zero when no reference signal is present
and for digital blanking input references.
Reference: Section 3.4.3 on page 45
1Fh
2
Ref_Blank_Timing - status register to indicate the input
detection of H blanking vs. H sync timing (‘1’ for
blanking, '0' for sync timing).
This bit will be zero when no reference signal is present.
Reference: Section 3.4.3 on page 45
1Fh
1
A_pll_Lock (GS4911B only)- this bit will be HIGH when
the generated audio clock is locked to the video clock
reference.
NOTE: This bit will remain high in the GS4910B.
Reference: bit 1 of register 15h.
1Fh
0
V_pll_Lock - this bit will be HIGH when the generated
video clock is locked to the H Sync input reference.
Reference: bit 1 of register 15h.
36655 - 2
April 2006
85 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Nv
21h-20h
31-0
A non-zero number programmed in this register defines
the numerator for the ratio of the video clock to the
27MHz reference.
R/W
–
R/W
–
This register can be used for creating custom video
clock frequencies.
NOTE: Once this register is programmed, it must be
updated using bit 6 of register 16h.
The default value of this register will vary depending on
the output video standard selected.
Address 20h = bits 15-0
Address 21h = bits 31-16
Reference: Section 3.9.1 on page 72
Dv
23h-22h
31-0
A non-zero number programmed in this register defines
the denominator for the ratio of the video clock to the
27MHz reference.
This register can be used for creating custom video
clock frequencies.
NOTE: Once this register is programmed, it must be
updated using bit 6 of register 16h.
The default value of this register will vary depending on
the output video standard selected.
Address 22h = bits 15-0
Address 23h = bits 31-16
Reference: Section 3.9.1 on page 72
36655 - 2
April 2006
86 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Constcf_Genlock
24h
15-8
Crash_Time - controls the crash lock period of video
PLL locking process. This time contributes to the total
PLL Lock Time given in the AC Characteristics Table.
R/W
–
R/W
–
R/W
–
The time of the crash process in H reference periods is
determined by [Crash_Time x 4] + 1.
The default value of these bits will vary depending on
the output video standard selected.
Reference: Section 3.6.3 on page 58
24h
7-3
Lock_Lost_Threshold - controls the threshold of the lock
indication circuit. A larger value programmed in this
register can increase the stability of the LOCK_LOST
output signal when the input H reference signal is
subject to large amounts of low frequency jitter. A larger
value in this register will also increase the lock indication
time, although not the actual lock time of the device.
The default value of these bits will vary depending on
the output video standard selected.
24h
2-0
Run_Window - controls the output frequency error in the
case of a missing or mis-timed H reference transition.
The default value of this register allows the device to
maintain genlock through one missing input H pulse.
This feature can be disabled by programming
Run_Window = 000b. In this case, the device will
immediately react to any disturbance of the input H
signal.
The default value of these bits will vary depending on
the output video standard selected.
Reference: Section 3.5.3 on page 47
RSVD
25h
–
Reserved.
–
–
Video_Cap_Genlock
26h
15-6
Reserved. Set these bits to zero when writing to 26h.
–
–
26h
5-0
Control signal to adjust loop bandwidth of video genlock
block.
R/W
–
The value programmed in this register must be between
10 and Video_Res_Genlock - 21.
The default value of this register will vary depending on
the output video standard selected.
Reference: Section 3.6.4 on page 58
Video_Res_Genlock
27h
15-6
Reserved. Set these bits to zero when writing to 27h.
–
–
27h
5-0
Control signal to adjust loop bandwidth of video genlock
block.
R/W
–
The value programmed in this register must be between
32 and 42.
The default value of this register will vary depending on
the output video standard selected.
Reference: Section 3.6.4 on page 58
36655 - 2
April 2006
87 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
H_Feedback_Divide
29h-28h
31-0
In the internal video genlock block, this register defines
the numerator of the divide ratio.
R/W
–
R/W
–
This register may be programmed to manually genlock
the output to the input reference.
The default value of this register will vary depending on
the output video standard selected.
Address 28h = bits 15-0
Address 29h = bits 31-16
Reference: Section 3.6.2.1 on page 54
H_Reference_Divide
2Bh-2Ah
31-0
In the internal video genlock block, this register defines
the denominator of the divide ratio.
This register may be programmed to manually genlock
the output to the input reference.
The default value of this register will vary depending on
the output video standard selected.
Address 2Ah = bits 15-0
Address 2Bh = bits 31-16
Reference: Section 3.6.2.1 on page 54
PCLK1_Phase/Divide
2Ch
15-7
Reserved. Set these bits to zero when writing to 2Ch.
–
–
2Ch
6
Current_P1 - selects the current drive capability of the
PCLK1 pin. Set this bit HIGH for high current drive.
Otherwise, the current drive will be low.
R/W
0
R/W
0
R/W
0
R/W
0
NOTE: The current drive should be set high if PCLK1 is
greater than 100MHz.
Reference: Section 3.7.1 on page 61
2Ch
5-2
PCLK1_Phase - adjusts the output phase of the PCLK1
clock with respect to the timing output pins. Phase is
delayed in 700ps (nominal) increments as shown in
Table 3-6.
Reference: Section 3.7.1 on page 61
2Ch
1
Divide_By_4 - set this bit HIGH to divide the output
PCLK1 by four.
NOTE: Setting this bit and bit 0 simultaneously HIGH
will hold the PCLK1 pin LOW.
Reference: Section 3.7.1 on page 61
2Ch
0
Divide_By_2 - set this bit HIGH to divide the output
PCLK1 by two.
NOTE: Setting this bit and bit 1 simultaneously HIGH
will hold the PCLK1 pin LOW.
Reference: Section 3.7.1 on page 61
36655 - 2
April 2006
88 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
PCLK2_Phase/Divide
2Dh
15-7
Reserved. Set these bits to zero when writing to 2Dh.
–
–
2Dh
6
Current_P2 - selects the current drive capability of the
PCLK2 pin. Set this bit HIGH for high current drive.
Otherwise, the current drive will be low.
R/W
0
R/W
0
R/W
0
R/W
0
NOTE: The current drive should be set high if PCLK2 is
greater than 100MHz.
Reference: Section 3.7.1 on page 61
2Dh
5-2
PCLK2_Phase - adjusts the output phase of the PCLK2
clock with respect to the timing output pins. Phase is
delayed in 700ps (nominal) increments as shown in
Table 3-6.
Reference: Section 3.7.1 on page 61
2Dh
1
Divide_By_4 - set this bit HIGH to divide the output
PCLK2 by four.
NOTE: Setting this bit and bit 0 simultaneously HIGH
will hold the PCLK2 pin LOW.
Reference: Section 3.7.1 on page 61
2Dh
0
Divide_By_2 - set this bit HIGH to divide the output
PCLK2 by two.
NOTE: Setting this bit and bit 1 simultaneously HIGH
will hold the PCLK2 pin LOW.
Reference: Section 3.7.1 on page 61
PCLK3_Phase/Divide
2Eh
15-6
Reserved. Set these bits to zero when writing to 2Eh.
–
–
2Eh
5-2
PCLK3_Phase - adjusts the output phase of the
PCLK3/PCLK3 clock with respect to the timing output
pins. Phase is delayed in 700ps (nominal) increments
as shown in Table 3-6.
R/W
0
R/W
0
R/W
0
Reserved. Set these bits to zero when writing to 2Fh.
–
–
Set these bits to 11b to tristate the PCLK3 / PCLK3 pins.
R/W
00b
–
–
Reference: Section 3.7.1 on page 61
2Eh
1
Divide_By_4 - set this bit HIGH to divide the output
PCLK3/PCLK3 by four.
Setting this bit and bit 0 simultaneously HIGH will give
the full rate video clock on the PCLK3 / PCLK3 pins.
Reference: Section 3.7.1 on page 61
2Eh
0
Divide_By_2 - set this bit HIGH to divide the output
PCLK3/PCLK3 by two.
Setting this bit and bit 1 simultaneously HIGH will give
the full rate video clock on the PCLK3 / PCLK3 pins.
Reference: Section 3.7.1 on page 61
PCLK3_Tristate
2Fh
15-2
2Fh
1-0
Reference: Section 3.7.1 on page 61
RSVD
2Fh - 30h
–
36655 - 2
Reserved.
April 2006
89 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Audio_Control
(GS4911B only)
31h
15-10
Reserved. Set these bits to zero when writing to 31h.
–
–
31h
9-7
AFS_Reset_Window - These bits may be used to adjust
the value by which the audio clock counters are allowed
to drift from the output AFS pulse.
R/W
010b
The encoding scheme for this register is shown in
Table 3-9.
NOTE: The default setting of this register will provide a
reset window that is sufficient for most standards. To
maintain correct audio clock frequencies for some
VESA standards, the reset window may have to be
increased from its default setting. In this case, set the
value of this register to 1XX. See Table 3-9.
Reference: Section 3.7.2 on page 63
31h
6
Update_Custom_A_Clock - this bit is used to update the
custom audio clock parameters programmed in
registers 33h to 36h of the host interface. All non-zero
parameters in these registers will be updated via a LOW
to HIGH transition on this bit.
R/W
0
31h
5
Enable_384fs - set this bit HIGH to enable the 384fs
and 192fs audio clock outputs. This must be set in
addition to registers 3Fh to 41h.
R/W
0
NOTE: If this bit is HIGH, then a 512fs audio clock will
have a 33% duty cycle when fs = 96kHz.
Reference: Section 3.7.2 on page 63
31h
4-3
Reserved. Set these bits to zero when writing to 31h.
–
–
31h
2
Host_ASR_SEL - set this bit HIGH to select the audio
sample rate using register 32h instead of the external
ASR_SEL[2:0] pins.
R/W
0
R/W
0
R/W
0
The external ASR_SEL[2:0] pins will be ignored, but
should not be left floating.
Reference: Section 3.7.2 on page 63
31h
1
AFS_F_Pulse - set this bit to 1 to stretch the AFS pulse
duration from 1 line to 1 field.
Reference: Section 3.8.2 on page 68
31h
0
AFS_Reset_Disable - set this bit HIGH to disable the
10FID input reference pin from resetting the output AFS
pulse. If this bit is set HIGH, the output AFS pulse will
free-run or may be reset using register 1Ah. The
external 10FID pin should not be left floating.
Reference: Section 3.8.2 on page 68
ASR_SEL[2:0]
(GS4911B only)
32h
15-3
Reserved. Set these bits to zero when writing to 32h.
–
–
32h
2-0
Replaces the external ASR_SEL[2:0] pins when
Host_ASR_Select (bit 2 of address 31h) is HIGH.
R/W
011b
The default setting of this register corresponds to an
audio sample rate of 48kHz.
Reference: Section 3.7.2 on page 63
36655 - 2
April 2006
90 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Na
(GS4911B only)
34h-33h
31-0
A non-zero number programmed in this register defines
the numerator for the ratio of the audio clock to the
27MHz reference.
R/W
–
R/W
–
NOTE: Once this register is programmed, it must be
updated using bit 6 of register 31h.
The default value of this register will vary depending on
the output audio rate selected.
Address 33h = bits 15-0
Address 34h = bits 31-16
Reference: Section 3.9.2 on page 73.
Da
(GS4911B only)
36h-35h
31-0
A non-zero number programmed in this register defines
the denominator for the ratio of the audio clock to the
27MHz reference.
NOTE: Once this register is programmed, it must be
updated using bit 6 of register 31h.
The default value of this register will vary depending on
the output audio rate selected.
Address 35h = bits 15-0
Address 36h = bits 31-16
Reference: Section 3.9.2 on page 73.
RSVD
37h - 38h
–
Reserved.
–
–
Audio_Cap_Genlock
(GS4911B only)
39h
15-6
Reserved. Set these bits to zero when writing to 39h.
–
–
39h
5-0
Control signal to adjust loop bandwidth of audio genlock
block.
R/W
–
The value programmed in this register must be between
10 and Audio_Res_Genlock - 21.
The default value of this register will depend on the
fundamental sampling frequency selected.
Reference: Section 3.6.4 on page 58
Audio_Res_Genlock
(GS4911B only)
3Ah
15-6
Reserved. Set these bits to zero when writing to 3Ah.
–
–
3Ah
5-0
Control signal to adjust loop bandwidth of audio genlock
block.
R/W
–
R/W
–
The value programmed in this register must be between
32 and 42.
The default value of this register will depend on the
fundamental sampling frequency selected.
Reference: Section 3.6.4 on page 58
A_Feedback_Divide
(GS4911B only)
3Ch-3Bh
31-0
In the internal audio genlock block, this register defines
the numerator of the divide ratio.
This register may be programmed to manually genlock
the audio clock to the video clock.
The default value of this register will vary depending on
the output video standard selected.
Address 3Bh = bits 15-0
Address 3Ch = bits 31-16
Reference: Section 3.6.2.2 on page 56
36655 - 2
April 2006
91 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
A_Reference_Divide
(GS4911B only)
3Eh-3Dh
31-0
In the internal audio genlock block, this register defines
the denominator of the divide ratio.
R/W
–
This register may be programmed to manually genlock
the audio clock to the video clock.
The default value of this register will vary depending on
the output video standard selected.
Address 3Dh = bits 15-0
Address 3Eh = bits 31-16
Reference: Section 3.6.2.2 on page 56
ACLK1_fs_Multiple
(GS4911B only)
3Fh
15-3
Reserved. Set these bits to zero when writing to 3Fh.
–
–
3Fh
2-0
The user may set this register to select the desired
frequency of the audio clock on ACLK1 (a multiple of the
fundamental sampling rate, fs). The audio clock
frequency may be set as: 512fs, 384fs, 256fs, 192fs,
128fs, 64fs, fs, or z-bit. See Table 3-8 for more details.
R/W
0
NOTE: To output a frequency of 348fs or 192fs, bit 5 of
register 31h must also be set HIGH.
Reference: Section 3.7.2 on page 63
ACLK2_fs_Multiple
(GS4911B only)
40h
15-3
Reserved. Set these bits to zero when writing to 40h.
–
–
40h
2-0
The user may set this register to select the desired
frequency of the audio clock on ACLK2 (a multiple of the
fundamental sampling rate, fs). The audio clock
frequency may be set as: 512fs, 384fs, 256fs, 192fs,
128fs, 64fs, fs, or z-bit. See Table 3-8 for more details.
R/W
0
NOTE: To output a frequency of 348fs or 192fs, bit 5 of
register 31h must also be set HIGH.
Reference: Section 3.7.2 on page 63
ACLK3_fs_Multiple
(GS4911B only)
41h
15-3
Reserved. Set these bits to zero when writing to 41h.
–
–
41h
2-0
The user may set this register to select the desired
frequency of the audio clock on ACLK3 (a multiple of the
fundamental sampling rate, fs). The audio clock
frequency may be set as: 512fs, 384fs, 256fs, 192fs,
128fs, 64fs, fs, or z-bit. See Table 3-8 for more details.
R/W
0
–
–
NOTE: To output a frequency of 348fs or 192fs, bit 5 of
register 31h must also be set HIGH.
Reference: Section 3.7.2 on page 63
RSVD
42h
–
36655 - 2
Reserved.
April 2006
92 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Output_Select_1
43h
15-5
Reserved. Set these bits to zero when writing to 43h.
–
–
43h
4
Current_1 - selects the current drive capability of the
TIMING_OUT_1 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0001b
Reference: Section 3.8.4 on page 71
43h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_1 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0001b, which
corresponds to H Sync.
Reference: Section 3.8.4 on page 71
Output_Select_2
44h
15-5
Reserved. Set these bits to zero when writing to 44h.
–
–
44h
4
Current_2 - selects the current drive capability of the
TIMING_OUT_2 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0010b
Reference: Section 3.8.4 on page 71
44h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_2 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0010b, which
corresponds to H Blanking.
Reference: Section 3.8.4 on page 71
Output_Select_3
45h
15-5
Reserved. Set these bits to zero when writing to 45h.
–
–
45h
4
Current_3 - selects the current drive capability of the
TIMING_OUT_3 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0011b
Reference: Section 3.8.4 on page 71
45h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_3 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0011b, which
corresponds to V Sync.
Reference: Section 3.8.4 on page 71
Output_Select_4
46h
15-5
Reserved. Set these bits to zero when writing to 46h.
–
–
46h
4
Current_4 - selects the current drive capability of the
TIMING_OUT_4 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0100b
Reference: Section 3.8.4 on page 71
46h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_4 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0100b, which
corresponds to V Blanking.
Reference: Section 3.8.4 on page 71
36655 - 2
April 2006
93 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Output_Select_5
47h
15-5
Reserved. Set these bits to zero when writing to 47h.
–
–
47h
4
Current_5 - selects the current drive capability of the
TIMING_OUT_5 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0101b
Reference: Section 3.8.4 on page 71
47h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_5 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0101b, which
corresponds to F Sync.
Reference: Section 3.8.4 on page 71
Output_Select_6
48h
15-5
Reserved. Set these bits to zero when writing to 48h.
–
–
48h
4
Current_6 - selects the current drive capability of the
TIMING_OUT_6 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0110b
Reference: Section 3.8.4 on page 71
48h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_6 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0110b, which
corresponds to F Digital.
Reference: Section 3.8.4 on page 71
Output_Select_7
49h
15-5
Reserved. Set these bits to zero when writing to 49h.
–
–
49h
4
Current_7 - selects the current drive capability of the
TIMING_OUT_7 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
0111b
Reference: Section 3.8.4 on page 71
49h
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_7 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 0111b, which
corresponds to 10FID.
Reference: Section 3.8.4 on page 71
Output_Select_8
4Ah
15-5
Reserved. Set these bits to zero when writing to 4Ah.
–
–
4Ah
4
Current_8 - selects the current drive capability of the
TIMING_OUT_8 pin. Set this bit HIGH for high current
drive. Otherwise, the current drive will be low.
R/W
0
R/W
1000b
Reference: Section 3.8.4 on page 71
4Ah
3-0
This register is used to select one of the 10
pre-programmed or 4 user programmed timing signals
available for output on the TIMING_OUT_8 pin. See
Table 3-11 for more details.
Note: The default setting of this register is 1000b, which
corresponds to Display Enable (DE).
Reference: Section 3.8.4 on page 71
36655 - 2
April 2006
94 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
RSVD
4Bh
–
Reserved.
–
–
Video_Control
4Ch
15-5
Reserved. Set these bits to zero when writing to 4Ch.
–
–
4Ch
4
10FID_F_pulse - set this bit HIGH to stretch the 10FID
pulse duration from 1 line to 1 field.
R/W
0
Reference: Section 3.8.1 on page 67
4Ch
3-2
Reserved. Set these bits to zero when writing to 4Ch.
–
–
4Ch
1
Host_VID_STD - set this bit HIGH to select the output
video standard using register 4Dh instead of the
external VID_STD[5:0] pins.
R/W
0
The external VID_STD[5:0] pins will be ignored, but
should not be left floating.
Reference: Section 1.4 on page 20
VID_STD[5:0]
4Ch
0
Reserved. Set this bit to zero when writing to 4Ch.
–
–
4Dh
15-6
Reserved. Set these bits to zero when writing to 4Dh.
–
–
4Dh
5-0
Replaces the external VID_STD[5:0] pins when
VID_From_Host (bit 1 of address 4Ch) is HIGH.
R/W
00h
R/W
–
R/W
–
R/W
–
R/W
–
Reference: Section 1.4 on page 20
Clocks_Per_Line
4Eh
15-0
Contains the number of output video clock cycles per
line for the selected output timing format.
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
Reference: Section 3.10 on page 74
Clocks_Per_Hsync
4Fh
15-0
Contains the number of output video clock cycles in the
active H Sync interval for the selected output timing
format.
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
Reference: Section 3.10 on page 74
Hsync_To_SAV
50h
15-0
Contains the number of output video clock cycles from
the start of H Sync to the start of active video for the
selected output timing format.
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
Reference: Section 3.10 on page 74
Hsync_To_EAV
51h
15-0
Contains the number of output video clock cycles from
the start of H Sync to the end of active video for the
selected output timing format.
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
Reference: Section 3.10 on page 74
36655 - 2
April 2006
95 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Lines_Per_Field
52h
15-0
Contains the number of lines per field for the selected
output timing format.
R/W
–
R/W
–
R/W
–
R/W
–
This register is 15.1 encoded (i.e. bit 0 represents 0.5
when set HIGH and 0 when set LOW).
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
NOTE: When bit 0 of this register is programmed HIGH,
the device assumes an interlaced output. Otherwise it
assumes a progressive output. For example,
programming ‘262.5’d will result in an interlaced output
standard with 525 lines per frame. Programming ‘525’d
will result in a progressive output with 525 lines per
frame.
Reference: Section 3.10 on page 74
Lines_Per_Vsync
53h
15-0
Contains the number of lines per active V Sync interval
for the selected output timing format.
This register is 15.1 encoded (i.e. bit 0 represents '0.5'
when set HIGH and '0' when set LOW).
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
Reference: Section 3.10 on page 74
Vsync_To_First_Active_Line
54h
15-0
Contains the number of lines from the start of V Sync to
the start of active video for the selected output timing
format.
This register is 15.1 encoded (i.e. bit 0 represents '0.5'
when set HIGH and '0' when set LOW).
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
NOTE1: The value programmed in this register will be
increased by 1 by the device such that V Blanking signal
generated will be one line longer than programmed.
NOTE2: For the pre-programmed output video
standards 3, 5, and 7, the value contained in this
register is incorrectly reported as 17 lines, although the
actual timing produced is correct at 16 lines.
Reference: Section 3.10 on page 74
Vsync_To_Last_Active_Line
55h
15-0
Contains the number of lines from the start of V Sync to
the end of active video for the selected output timing
format.
This register is 15.1 encoded (i.e. bit 0 represents '0.5'
when set HIGH and '0' when set LOW).
If VID_STD[5:0] = 62, this register may be set by the
user when programming custom output timing signals.
Otherwise, this register is read-only.
NOTE: The user cannot specify a custom vertical
blanking signal to end in the middle of a line. If this
occurs, the device will automatically adjust the timing of
the signal to fall at the beginning of the next line.
Reference: Section 3.10 on page 74
36655 - 2
April 2006
96 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Polarity
56h
15-10
Reserved. Set these bits to zero when writing to 56h.
–
–
56h
9
AFS (GS4911B only)- set this bit HIGH to invert the
polarity of the AFS timing output signal.
R/W
0
R/W
0
R/W
0
By default, the AFS signal is HIGH for the duration of
the first line of the n’th video frame to indicate that the
ACLK dividers have been reset at the start of line 1 of
that frame.
NOTE: The GS4910B does not generate an AFS pulse
and will ignore the setting of this bit.
Reference: Table 1-3
56h
8
10FID - set this bit HIGH to invert the polarity of the
10FID timing output signal.
By default, the 10FID signal will go HIGH for one line at
the start of the 10-field sequence.
Reference: Table 1-3
56h
7
DE - set this bit HIGH to invert the polarity of the DE
timing output signal.
By default, the DE signal will be HIGH whenever pixel
information is to be displayed on the display device
Reference: Table 1-3
56h
6
Reserved. Set this bit to zero when writing to 56h.
–
–
56h
5
F_Digital - set this bit HIGH to invert the polarity of the F
Digital timing output signal.
R/W
0
R/W
0
R/W
0
By default, the F Digital signal will be LOW for the entire
period of field 1.
Reference: Table 1-3
56h
4
F_Sync - set this bit HIGH to invert the polarity of the F
Sync timing output signal.
By default, the F Sync signal will be HIGH for the entire
period of field 1.
Reference: Table 1-3
56h
3
V_Blanking - set this bit HIGH to invert the polarity of the
V Blanking timing output signal.
By default, the V Blanking signal will be LOW for the
portion of the field/frame containing valid video data.
Reference: Table 1-3
36655 - 2
April 2006
97 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
56h
2
V_Sync - set this bit HIGH to invert the polarity of the V
Sync timing output signal.
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
By default, the V Sync signal is active LOW.
Reference: Table 1-3
56h
1
H_Blanking - set this bit HIGH to invert the polarity of
the H Blanking timing output signal.
By default, the H Blanking signal will be LOW for the
portion of the video line containing valid video samples.
Reference: Table 1-3
56h
0
H_Sync - set this bit HIGH to invert the polarity of the H
Sync timing output signal.
By default, the H Sync signal is active LOW.
Reference: Table 1-3
H_Start_1
57h
15-0
The value programmed in this register indicates the
pixel start point for the leading edge of the
user-programmed H Sync signal USER1_H.
NOTE: The value programmed in this register must be
less than the value programmed in H_Stop_1.
Reference: Section 3.8.3 on page 69
H_Stop_1
58h
15-0
The value programmed in this register indicates the
pixel end point for the trailing edge of the
user-programmed H Sync signal USER1_H.
NOTE: The value programmed in this register must not
exceed the maximum number of clock periods per line
of the outgoing standard.
Reference: Section 3.8.3 on page 69
V_Start_1
59h
15
Reserved. Set this bit to zero when writing to 59h.
–
–
59h
14-0
The value programmed in this register indicates the start
line number of the leading edge of the
user-programmed V Sync signal USER1_V. For
interlaced output standards, this value corresponds to
the odd field number.
R/W
0
NOTE: The value programmed in this register must be
less than the value programmed in V_Stop_1.
Reference: Section 3.8.3 on page 69
V_Stop_1
5Ah
15
Reserved. Set this bit to zero when writing to 5Ah.
–
–
5Ah
14-0
The value programmed in this register indicates the end
line number of the trailing edge of the user-programmed
V Sync signal USER1_V. For interlaced output
standards, this value corresponds to the odd field
number.
R/W
0
NOTE: The value programmed in this register must not
exceed the maximum number of lines per field of the
outgoing standard.
Reference: Section 3.8.3 on page 69
36655 - 2
April 2006
98 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Operator_Polarity_1
5Bh
15-4
Reserved. Set these bits to zero when writing to 5Bh.
–
–
5Bh
3
Polarity_1 - Use this bit to invert the polarity of the final
USER1 signal.
R/W
1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
By default, the polarity of the user programmed signals
is active LOW. The polarity may be switched to active
HIGH by setting this bit LOW.
Reference: Section 3.8.3 on page 69
5Bh
2
AND_1 - logical operator: USER1_H AND USER1_V
Set this bit HIGH to output a signal that is only active
when both USER1_H and USER1_V are active.
When this bit is HIGH, bit 1 and bit 0 of this register will
be ignored.
Reference: Section 3.8.3 on page 69
5Bh
1
OR_1 - logical operator: USER1_H OR USER1_V
Set this bit HIGH to output a signal that is active
whenever USER1_H or USER1_V are active.
When this bit is HIGH bit 0 of this register will be
ignored.
Reference: Section 3.8.3 on page 69
5Bh
0
XOR_1 - logical operator: USER1_H XOR USER1_V
Set this bit HIGH to output a signal with the following
attributes: Signal becomes active when either
USER1_H or USER1_V is active. Signal is inactive
when USER1_H and USER1_V are both active or both
inactive.
Reference: Section 3.8.3 on page 69
H_Start_2
5Ch
15-0
The value programmed in this register indicates the
pixel start point for the leading edge of the
user-programmed H Sync signal USER2_H.
NOTE: The value programmed in this register must be
less than the value programmed in H_Stop_2
Reference: Section 3.8.3 on page 69
H_Stop_2
5Dh
15-0
The value programmed in this register indicates the
pixel end point for the trailing edge of the
user-programmed H Sync signal USER2_H.
NOTE: The value programmed in this register must not
exceed the maximum number of clock periods per line
of the outgoing standard.
Reference: Section 3.8.3 on page 69
V_Start_2
5Eh
15
Reserved. Set this bit to zero when writing to 5Eh.
–
–
5Eh
14-0
The value programmed in this register indicates the start
line number of the leading edge of the
user-programmed V Sync signal USER2_V. For
interlaced output standards, this value corresponds to
the odd field line number.
R/W
0
NOTE: The value programmed in this register must be
less than the value programmed in V_Stop_2.
Reference: Section 3.8.3 on page 69
36655 - 2
April 2006
99 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
V_Stop_2
5Fh
15
Reserved. Set this bit to zero when writing to 5Fh.
–
–
5Fh
14-0
The value programmed in this register indicates the end
line number of the trailing edge of the user-programmed
V Sync signal USER2_V. For interlaced output
standards, this value corresponds to the odd field line
number.
R/W
0
NOTE: The value programmed in this register must not
exceed the maximum number of lines per field of the
outgoing standard.
Reference: Section 3.8.3 on page 69
Operator_Polarity_2
60h
15-4
Reserved. Set these bits to zero when writing to 60h.
–
–
60h
3
Polarity_2 - Use this bit to invert the polarity of the final
USER2 signal.
R/W
1
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
By default, the polarity of the user programmed signals
is active LOW. The polarity may be switched to active
HIGH by setting this bit LOW.
Reference: Section 3.8.3 on page 69
60h
2
AND_2 - logical operator: USER2_H AND USER2_V
Set this bit HIGH to output a signal that is only active
when both USER2_H and USER2_V are active.
When this bit is HIGH, bit 1 and bit 0 of this register will
be ignored.
Reference: Section 3.8.3 on page 69
60h
1
OR_2 - logical operator: USER2_H OR USER2_V
Set this bit HIGH to output a signal that is active
whenever USER2_H or USER2_V are active.
When this bit is HIGH bit 0 of this register will be
ignored.
Reference: Section 3.8.3 on page 69
60h
0
XOR_2 - logical operator: USER2_H XOR USER2_V
Set this bit HIGH to output a signal with the following
attributes: Signal becomes active when either
USER2_H or USER2_V is active. Signal is inactive
when USER2_H and USER2_V are both active or both
inactive.
Reference: Section 3.8.3 on page 69
H_Start_3
61h
15-0
The value programmed in this register indicates the
pixel start point for the leading edge of the
user-programmed H Sync signal USER3_H.
NOTE: The value programmed in this register must be
less than the value programmed in H_Stop_3.
Reference: Section 3.8.3 on page 69
H_Stop_3
62h
15-0
The value programmed in this register indicates the
pixel end point for the trailing edge of the
user-programmed H Sync signal USER3_H.
NOTE: The value programmed in this register must not
exceed the maximum number of clock periods per line
of the outgoing standard.
Reference: Section 3.8.3 on page 69
36655 - 2
April 2006
100 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
V_Start_3
63h
15
Reserved. Set this bit to zero when writing to 63h.
–
–
63h
14-0
The value programmed in this register indicates the start
line number of the leading edge of the
user-programmed V Sync signal USER3_V. For
interlaced output standards, this value corresponds to
the odd field line number.
R/W
0
NOTE: The value programmed in this register must be
less than the value programmed in V_Stop_3.
Reference: Section 3.8.3 on page 69
V_Stop_3
64h
15
Reserved. Set this bit to zero when writing to 64h.
–
–
64h
14-0
The value programmed in this register indicates the end
line number of the trailing edge of the user-programmed
V Sync signal USER3_V. For interlaced output
standards, this value corresponds to the odd field line
number.
R/W
0
NOTE: The value programmed in this register must not
exceed the maximum number of lines per field of the
outgoing standard.
Reference: Section 3.8.3 on page 69
Operator_Polarity_3
65h
15-4
Reserved. Set these bits to zero when writing to 65h.
–
–
65h
3
Polarity_3 - Use this bit to invert the polarity of the final
USER3 signal.
R/W
1
R/W
0
R/W
0
R/W
0
By default, the polarity of the user programmed signals
is active LOW. The polarity may be switched to active
HIGH by setting this bit LOW.
Reference: Section 3.8.3 on page 69
65h
2
AND_3 - logical operator: USER3_H AND USER3_V
Set this bit HIGH to output a signal that is only active
when both USER3_H and USER3_V are active.
When this bit is HIGH, bit 1 and bit 0 of this register will
be ignored.
Reference: Section 3.8.3 on page 69
65h
1
OR_3 - logical operator: USER3_H OR USER3_V
Set this bit HIGH to output a signal that is active
whenever USER3_H or USER3_V are active.
When this bit is HIGH bit 0 of this register will be
ignored.
Reference: Section 3.8.3 on page 69
65h
0
XOR_3 - logical operator: USER3_H XOR USER3_V
Set this bit HIGH to output a signal with the following
attributes: Signal becomes active when either
USER3_H or USER3_V is active. Signal is inactive
when USER3_H and USER3_V are both active or both
inactive.
Reference: Section 3.8.3 on page 69
36655 - 2
April 2006
101 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
H_Start_4
66h
15-0
The value programmed in this register indicates the
pixel start point for the leading edge of the
user-programmed H Sync signal USER4_H.
R/W
0
R/W
0
NOTE: The value programmed in this register must be
less than the value programmed in H_Stop_4.
Reference: Section 3.8.3
H_Stop_4
67h
15-0
The value programmed in this register indicates the
pixel end point for the trailing edge of the
user-programmed H Sync signal USER4_H.
NOTE: The value programmed in this register must not
exceed the maximum number of clock periods per line
of the outgoing standard.
Reference: Section 3.8.3 on page 69
V_Start_4
68h
15
Reserved. Set this bit to zero when writing to 68h.
–
–
68h
14-0
The value programmed in this register indicates the start
line number of the leading edge of the
user-programmed V Sync signal USER4_V. For
interlaced output standards, this value corresponds to
the odd field line number.
R/W
0
NOTE: The value programmed in this register must be
less than the value programmed in V_Stop_4.
Reference: Section 3.8.3 on page 69
V_Stop_4
69h
15
Reserved. Set this bit to zero when writing to 69h.
–
–
69h
14-0
The value programmed in this register indicates the end
line number of the trailing edge of the user-programmed
V Sync signal USER4_V. For interlaced output
standards, this value corresponds to the odd field line
number.
R/W
0
NOTE: The value programmed in this register must not
exceed the maximum number of lines per field of the
outgoing standard.
Reference: Section 3.8.3 on page 69
36655 - 2
April 2006
102 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Operator_Polarity_4
6Ah
15-4
Reserved. Set these bits to zero when writing to 6Ah.
–
–
6Ah
3
Polarity_4 - Use this bit to invert the polarity of the final
USER4 signal.
R/W
1
R/W
0
R/W
0
R/W
0
R/W
0
By default, the polarity of the user programmed signals
is active LOW. The polarity may be switched to active
HIGH by setting this bit LOW.
Reference: Section 3.8.3 on page 69
6Ah
2
AND_4 - logical operator: USER4_H AND USER4_V
Set this bit HIGH to output a signal that is only active
when both USER4_H and USER4_V are active.
When this bit is HIGH, bit 1 and bit 0 of this register will
be ignored.
Reference: Section 3.8.3 on page 69
6Ah
1
OR_4 - logical operator: USER4_H OR USER4_V
Set this bit HIGH to output a signal that is active
whenever USER4_H or USER4_V are active.
When this bit is HIGH bit 0 of this register will be
ignored.
Reference: Section 3.8.3 on page 69
6Ah
0
XOR_4 - logical operator: USER4_H XOR USER4_V
Set this bit HIGH to output a signal with the following
attributes: Signal becomes active when either
USER4_H or USER4_V is active. Signal is inactive
when USER4_H and USER4_V are both active or both
inactive.
Reference: Section 3.8.3 on page 69
Ext_Audio_Mode
81h
15-0
Set this register to 20C1h to enable the Extended Audio
Mode of the device.
To fully enable this mode, VID_STD[5:0] must be set to
4d, and the F_Lock_Mask and V_Lock_Mask bits [4:3]
of register address 16h must be set to 1.
NOTE: Once this register is programmed, it must be
updated using bit 6 of register 16h.
Reference: Section 3.11 on page 75
36655 - 2
April 2006
103 of 113
GS4911B/GS4910B Data Sheet
Table 3-13: Configuration and Status Registers (Continued)
Register Name
Address
Bit
Description
R/W
Default
Ln_Count_Reset
83h
15
Toggle this bit to reset the line-based counters in the
device.
R/W
0
–
–
This is only required when locking the “f/1.001” HD
output standards to the 525-line SD input reference
standards, or vice-versa, AND:
1. The reference has been removed and subsequently
re-applied. In this case, the user should wait until the
reference has been re-detected by the device, which
may take up to 4 frames. See Section 3.5.3 on
page 47.
OR
2. The device is locked to blanking signals from a
deserializer, and the SDI input to the deserializer has
been switched upstream from the system. See
Section 3.6.5 on page 60.
83h
14-0
36655 - 2
Reserved. Set these bits to zero when writing to 83h.
April 2006
104 of 113
GS4911B/GS4910B Data Sheet
3.13 JTAG
When the JTAG/HOST input pin of the GS4911B/GS4910B is set HIGH, the host
interface port will be configured for JTAG test operation. In this mode, pins 57
through 60 become TCLK, TDI, TDO, and TMS. In addition, the RESET pin will
operate as the test reset pin.
Boundary scan testing using the JTAG interface will be enabled in this mode.
There are two methods in which JTAG can be used on the GS4911B/GS4910B:
1. As a stand-alone JTAG interface to be used at in-circuit ATE (Automatic Test
Equipment) during PCB assembly; or
2. Under control of the host for applications such as system power on self tests.
When the JTAG tests are applied by ATE, care must be taken to disable any other
devices driving the digital I/O pins. If the tests are to be applied only at ATE, this
can be accomplished with high-impedance buffers used in conjunction with the
JTAG/HOST input signal. This is shown in Figure 3-19.
Application HOST
GS4911B/GS4910B
CS_TMS
SCLK_TCLK
SDIN_TDI
SDOUT_TDO
JTAG/HOST
In-circuit ATE probe
Figure 3-19: In-Circuit JTAG
Alternatively, if the test capabilities are to be used in the system, the host may still
control the JTAG/HOST input signal, but some means for tri-stating the host must
exist in order to use the interface at ATE. This is represented in Figure 3-20.
36655 - 2
April 2006
105 of 113
GS4911B/GS4910B Data Sheet
Application HOST
GS4911B/GS4910B
CS_TMS
SCLK_TCLK
SDIN_TDI
SDOUT_TDO
JTAG/HOST
Tri-State
In-circuit ATE probe
Figure 3-20: System JTAG
3.14 Device Power-Up
3.14.1 Power Supply Sequencing
The GS4911B/GS4910B has a recommended power supply sequence. To ensure
correct power-up, the ANALOG_VDD and CORE_VDD power pins should be
powered before IO_VDD.
Device pins may be driven prior to power-up without causing damage.
3.15 Device Reset
In order to initialize operating conditions to their default states, the application layer
must hold the RESET signal LOW during power up and for a minimum of 500us
after the last supply has reached its operating voltage.
36655 - 2
April 2006
106 of 113
GS4911B/GS4910B Data Sheet
4. Application Reference Design
4.1 GS4911B Typical Application Circuit
JTAG/HOSTb
SCLK
SDIN
SDOUT
CSb
VDD_IO
VDD_IO
10n
10n
1V8_VPLL
1V8_PCLK
10n
10n
GND_VPLL
22R
RESETb
PCLK1
22R
PCLK2
GENLOCKb
Controlled impedance
100-ohms differential
PCLK3
PCLK3b
GENLOCK
NC
IO_VDD
RESET
CS_TMS
SDOUT_TDO
SDIN_TDI
SCLK_TCLK
JTAG/HOST
PHS_GND
PHS_VDD
PCLK1&2_VDD
PCLK1&2_GND
PCLK1
IO_VDD
PCLK2
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
LOCK_LOST
REF_LOST
1V8_VPLL
10n
1V8_PCLK
VDD_IO
1V8_CORE
10n
VDD_XTAL
GND_VPLL
27MHz
38pF
1M
10n
24pF
0R
GND_XTAL
1V8_APLL
GND_XTAL
10n
LOCK_LOST
REF_LOST
VID_PLL_VDD
VID_PLL_GND
XTAL_VDD
X1
X2
XTAL_GND
CORE_GND
ANALOG_VDD
NC
ANALOG_GND
AUD_PLL_GND
AUD_PLL_VDD
10FID
HSYNC
GS4911B
GND_APLL
The 10FID input must be
grounded if it will not be used
65
LVDS/PCLK3_GND
PCLK3
PCLK3
LVDS/PCLK3_VDD
CORE_VDD
TIMING_OUT8
TIMING_OUT7
TIMING_OUT6
TIMING_OUT5
TIMING_OUT4
IO_VDD
TIMING_OUT3
TIMING_OUT2
TIMING_OUT1
ASR_SEL0
ASR_SEL1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
10n
10n
22R
22R
22R
22R
22R
TIMING8
TIMING7
TIMING6
TIMING5
TIMING4
22R
22R
22R
TIMING3
TIMING2
TIMING1
VSYNC
IO_VDD
FSYNC
NC
VID_STD0
VID_STD1
VID_STD2
VID_STD3
VID_STD4
CORE_VDD
VID_STD5
ACLK1
ACLK2
ACLK3
IO_VDD
ASR_SEL2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
GND_PAD
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
10FID
HSYNC
VSYNC
FSYNC
22R
22R
22R
VDD_IO
1V8_CORE
10n
ACLK1
ACLK2
ACLK3
10n
NOTE: The GS4911A inputs are 5V tolerant for
3V3 I/O operation only (IO_VDD=3V3)
10n
VID_STD0
VID_STD1
VID_STD2
VID_STD3
VID_STD4
VID_STD5
ASR_SEL0
ASR_SEL1
ASR_SEL2
NOTE: For a solution with the lowest output jitter, the GS1531 or GS1532
serializers are recommended for use with the GS4911B/GS4910B.
36655 - 2
April 2006
107 of 113
GS4911B/GS4910B Data Sheet
4.2 GS4910B Typical Application Circuit
JTAG/HOSTb
SCLK
SDIN
SDOUT
CSb
VDD_IO
VDD_IO
10n
10n
1V8_PCLK
1V8_VPLL
10n
10n
GND_VPLL
22R
RESETb
PCLK1
22R
PCLK2
GENLOCKb
Controlled impedance
100-ohms differential
PCLK3
PCLK3b
GENLOCK
NC
IO_VDD
RESET
CS_TMS
SDOUT_TDO
SDIN_TDI
SCLK_TCLK
JTAG/HOST
PHS_GND
PHS_VDD
PCLK1&2_VDD
PCLK1&2_GND
PCLK1
IO_VDD
PCLK2
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
LOCK_LOST
REF_LOST
1V8_VPLL
10n
1V8_PCLK
VDD_IO
1V8_CORE
10n
VDD_XTAL
38pF
GND_VPLL
27MHz
1M
10n
24pF
0R
1V8_A
GND_XTAL
GND_XTAL
10n
LOCK_LOST
REF_LOST
VID_PLL_VDD
VID_PLL_GND
XTAL_VDD
X1
X2
XTAL_GND
CORE_GND
ANALOG_VDD
NC
ANALOG_GND
ANALOG_GND
ANALOG_GND
10FID
HSYNC
GND_A
The 10FID input must be
grounded if it will not be used
65
GND_PAD
LVDS/PCLK3_GND
PCLK3
PCLK3
LVDS/PCLK3_VDD
CORE_VDD
TIMING_OUT8
TIMING_OUT7
TIMING_OUT6
TIMING_OUT5
TIMING_OUT4
IO_VDD
TIMING_OUT3
TIMING_OUT2
TIMING_OUT1
ANALOG_GND
ANALOG_GND
GS4910B
VSYNC
IO_VDD
FSYNC
NC
VID_STD0
VID_STD1
VID_STD2
VID_STD3
VID_STD4
CORE_VDD
VID_STD5
NC
NC
NC
IO_VDD
ANALOG_GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
10n
10n
22R
22R
22R
22R
22R
TIMING8
TIMING7
TIMING6
TIMING5
TIMING4
22R
22R
22R
TIMING3
TIMING2
TIMING1
GND_A
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
10FID
HSYNC
VSYNC
FSYNC
VDD_IO
GND_A
1V8_CORE
10n
10n
10n
NOTE: The GS4910A inputs are 5V tolerant for
3V3 I/O operation only (IO_VDD=3V3)
VID_STD0
VID_STD1
VID_STD2
VID_STD3
VID_STD4
VID_STD5
NOTE: For a solution with the lowest output jitter, the GS1531 or GS1532
serializers are recommended for use with the GS4911B/GS4910B.
36655 - 2
April 2006
108 of 113
GS4911B/GS4910B Data Sheet
5. References & Relevant Standards
Table 5-1: References & Relevant Standards
AES11-1997
Synchronization of Digital Audio Equipment in Studio Operations
SMPTE 125M-1995
Component Video Signal 4:2:2 – Bit-Parallel Digital Interface
SMPTE 170M-1999
Composite Analog Video Signal – NTSC for Studio Applications
SMPTE 244M-1995
System M/NTSC Composite Video Signals – Bit-Parallel Digital
Interface
SMPTE 260M-1999
1125/60 High-Definition Production System – Digital Representation
and Bit-Parallel Interface
SMPTE 267M-1995
Bit-Parallel Digital Interface – Component Video Signal 4:2:2 16x9
Aspect Ratio
SMPTE 274M-1998
1920 x 1080 Scanning and Analog and Parallel Digital Interfaces for
Multiple Picture Rates
SMPTE 293M-1996
720 x 483 Active Line at 59.94-Hz Progressive Scan Production –
Digital Representation
SMPTE 296M-1997
1280 x 720 Scanning, Analog and Digital Representation an Analog
Interface
SMPTE 318M-1999
Synchronization of 59.94- or 50-Hz Related Video and Audio Systems
in Analog and Digital Areas – Reference Signals
SMPTE 347M-2001
540 Mb/s Serial Digital Interface – Source Image Format Mapping
SMPTE RP 164-1996
Location of Vertical Interval Time Code
SMPTE RP 168-1993
Definition of Vertical Interval Switching Point for Synchronous Video
Switching
SMPTE RP 211-2000
Implementation of 24P, 25P and 30P Segmented Frames for 1920 x
1080 Production Format
ITU-R BT.601-5
Studio Encoding Parameters of Digital Television for Standard 4:3 and
Wide-screen 16:9 Aspect Ratios
ITU-R BT.709-4
Parameter Values for the HDTV Standards for Production and
International Program Exchange ITU-R BT.799.3 Interface for Digital
Component Video Signals in 525-line and 625-line Television Systems
Operating at the 4:4:4 Level of Recommendation ITU-R BT.601 (PART
A)
ITU-R BT.1358
Studio Parameters of 625 and 525 Line Progressive Scan Television
Systems
VESA Monitor Timing
Specifications
VESA and industry Standards and Guidelines for Computer Display
Monitor Timing – Version 1.0, Revision 0.8 (Adoption Date: September
17, 1998)
36655 - 2
April 2006
109 of 113
GS4911B/GS4910B Data Sheet
6. Package & Ordering Information
B
4.50
0.95+/-0.05
A
9.00
0.40+/-0.05
6.1 Package Dimensions
7.10+/-0.15
9.00
PIN 1 AREA
7.10+/-0.15
4.50
3.55
4.50
3.55
CENTRE TAB
2X
2X
0.20 REF
0.15 C
0.15 C
0.10 C
+0.03
0.25-0.02
0.50
C
64X
C A B
0.10
C
0.05
64X
0.90 +/- 0.10
+0.03
0.02-0.02
0.08 C
SEATING PLANE
ALL DIMENSIONS IN MM
36655 - 2
April 2006
110 of 113
GS4911B/GS4910B Data Sheet
6.2 Recommended PCB Footprint
0.25
0.50
0.55
CENTER PAD
8.70
7.10
NOTE: All dimensions
are in millimeters.
7.10
8.70
The center pad of the PCB footprint should be connected to the ground plane by a
minimum of 36 vias.
NOTE: Suggested dimensions only. Final dimensions should conform to customer
design rules and process optimizations.
6.3 Packaging Data
Parameter
Value
Package Type
9mm x 9mm 64-pin QFN
Moisture Sensitivity Level
3
Junction to Case Thermal Resistance, θj-c
9.3°C/W
Junction to Air Thermal Resistance, θj-a (at zero airflow)
24.6°C/W
Psi, ψ
0.2°C/W
Pb-free and RoHS Compliant
Yes
36655 - 2
April 2006
111 of 113
GS4911B/GS4910B Data Sheet
6.4 Ordering Information
Part
Video
Clocks
Graphics
Clocks
Audio
Clocks
Full
Programmability
Max PCLK
Rate
GS4911B
√
√
√
√
165MHz
GS4910B
√
√
–
√
165MHz
Part Number
Package
Temperature Range
GS4911BCNE3
Pb-free 64-pin QFN
0°C to 70°C
GS4910BCNE3
Pb-free 64-pin QFN
0°C to 70°C
36655 - 2
April 2006
112 of 113
GS4911B/GS4910B Data Sheet
7. Revision History
Version
ECR
PCN
Date
Changes and/or Modifications
0
138004
–
November 2005
New document.
1
138866
37792
December 2005
Corrected phrasing regarding
user-programmable outputs. Added note
on V Blanking output width for
VID_STD=4, 6, 8. Corrected ESD
protection to 1 kV.
2
139291
38723
April 2006
Corrected description and formulas for
loop bandwidth. Converted to Data
Sheet. Clarified setting of VID_STD in
Extended Audio Mode. Updated power
consumption of GS4910B.
CAUTION
ELECTROSTATIC SENSITIVE DEVICES
DO NOT OPEN PACKAGES OR HANDLE
EXCEPT AT A STATIC-FREE WORKSTATION
DOCUMENT IDENTIFICATION
DATA SHEET
The product is in production. Gennum reserves the right to make
changes to the product at any time without notice to improve reliability,
function or design, in order to provide the best product possible.
GENNUM CORPORATION
Mailing Address: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3
Shipping Address: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5
Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946
GENNUM JAPAN CORPORATION
Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku, Shinjuku-ku, Tokyo, 160-0023 Japan
Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505
GENNUM UK LIMITED
25 Long Garden Walk, Farnham, Surrey, England GU9 7HX
Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523
Gennum Corporation assumes no liability for any errors or omissions in this document, or for the use of the
circuits or devices described herein. The sale of the circuit or device described herein does not imply any
patent license, and Gennum makes no representation that the circuit or device is free from patent infringement.
GENNUM and the G logo are registered trademarks of Gennum Corporation.
© Copyright 2005 Gennum Corporation. All rights reserved. Printed in Canada.
www.gennum.com
36655 - 2
April 2006
113 of 113
113