IMAGE SENSOR InGaAs multichannel detector head C8061/C8062-01 Designed for InGaAs linear image sensor C8061/C8062-01 series are high sensitivity multichannel detector heads for use with InGaAs linear image sensors. C8061-01 is designed for the onestage TE-cooled InGaAs linear image sensors and C8062-01 for two-stage TE-cooled InGaAs linear image sensors. C8061-01 and C8062-01 incorporate a low-noise driver/amplifier circuit that provide reliable operation from simple external signals. They also include a highly stable temperature controller that cools the sensor to a preset temperature level (C8061-01: Ts= -10 ˚C, C8062-01: Ts= -20 ˚C) as soon as the power is turned on. If the cooler fails and overheat occurs, the built-in protection circuit automatically turns off the power to maintain safety. Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochromators. Controller for multichannel detector head C7557 is also available. The software supplied with the C7557 allows easy control of the multichannel detector head and data acquisition. Features Applications l Designed for InGaAs linear image sensor C8061-01: One-stage TE-cooled type C8062-01: Two-stage TE-cooled type l Built-in driver/amplifier and temperature circuit l Highly stable temperature controller Cooling temperature (Ta=10 to 30 ˚C) fixed at -10 ± 0.1 ˚C (C8061-01), -20 ± 0.1 ˚C (C8062-01) l Simple signal input operation l Compact configuration l Near infrared multichannel spectroscopy l Radiation thermometry l Non-destructive inspection l Optical fiber transmittance measurement ■ Selection Guide The table below shows InGaAs image sensors applicable for the C8061/C8062-01. Scince the C8061/C8062-01 do not include a InGaAs image sensor, so select the desired sensor and order it sparately. Type No. C8061-01 C8062-01 Type No. G9201-256S G9202-512S G9203-256S G9204-512S G9211-256S G9212-512S G9213-256S G9214-512S G9205-256W G9206-256W G9207-256W G9208-256W Cooling One-stage TE-cooled Two-stage TE-cooled InGaAs linear image sensor Number of Number of Pixel size Active area *1 pixels active pixels [µm(H) × µm(V)] [mm (H) × mm (V)] 256 256 50 × 250 12.8 × 0.25 512 512 25 × 250 12.8 × 0.25 256 256 50 × 500 12.8 × 0.50 512 512 25 × 500 12.8 × 0.50 256 >251 50 × 250 12.8 × 0.25 512 >502 25 × 250 12.8 × 0.25 256 >251 50 × 500 12.8 × 0.50 512 >502 25 × 500 12.8 × 0.50 256 >244 50 × 250 12.8 × 0.25 *1: Number of active pixels: The total number of pixels whose dark current and sensitivity uniformity do not exceed the maximum values. 1 InGaAs multichannel detector head C8061/C8062-01 ■ Absolute maximum ratings Parameter Supply voltage (for digital circuitry) Symbol VD1, VD2 VA+ VAVp VF Topr Tstg Supply voltage (for analog circuitry) Supply voltage Digital input voltage Operating temperature Storage temperature Min. -0.5 - Typ. Max. +7 +18 -18 +7 +14 VD1, VD2 +10 to +30 0 to +50 Unit V °C ■ Electrical Characteristics [unless otherwise noted, Ta=25 °C, C8061-01: VD1,2=+5 V, VA+=+15 V, VA-=-15 V, VD2=+5 V, Vp=+5 V, VF=+12 V C8062-01: VD1=+5 V, VA+=+15 V, VA-=-15 V, VD2=+6 V, Vp=+6 V, VF=+12 V] Parameter High level Low level Digital input Master clock (CLK) pulse frequency Data video readout frequency Master start (start) pulse width High level (Io= -6 mA) Low level (Io=+6 mA) Digital output Symbol VIH VIL fCLK fv tst VoH VoL Min. +2.0 -0.5 1/fCLK +2.0 - Typ. - Max. VD1, 2 +0.8 4 fCLK/8 +0.8 Unit V V MHz Hz s V V VD1 VA1+ VA1- VF - +4.75 +14.5 -14.5 +4.75 +5.75 +4.75 +5.75 +11.75 - +5.0 +15.0 -15.0 +5.0 +6.0 +5.0 +6.0 +12.0 - +5.25 +15.5 -15.5 +5.25 +6.25 +5.25 +6.25 +12.25 +100 +200 -50 V V V V V V V V mA mA mA - - - +50 mA - - +1.2 +2.0 - +1.7 +3.0 +200 A A mA Power supply conditions Digital circuitry Analog circuitry Voltage Other Current 2 C8061-01 C8062-01 C8061-01 C8062-01 VD1 (+5 VDC) VA+ (+15 VDC) VA- (-15 VDC) VD2 C8061-01: +5 VDC C8062-01: +6 VDC C8061-01: +5 VDC Vp C8062-01: +6 VDC VF (+12 VDC) VD2 Vp InGaAs multichannel detector head C8061/C8062-01 ■ Electrical and optical characteristics [Unless otherwise noted, Ta=25 °C, C8061-01: Ts=-10 °C, G9211-256S (Cf=10 pF) , VD1=+5 V VA+=+15 V, VA-=-15 V, VD2=+5 V, Vp=+5 V, VF=+12 V C8062-01: Ts=-20 °C, G9208-256W (Cf=10 pF), VD1=+5 V, VA+=+15 V, VA-=-15 V, VD2=+6 V, Vp=+6 V, VF=+12 V ] Parameter Symbol Min. Typ. C8061-01 0.9 to 1.7 Spectral response range λ C8062-01 1.2 to 2.6 C8061-01 1.55 Peak sensitivity wavelength λp C8062-01 2.3 Saturation output charge Qsat 30 Conversion gain *2 G 0.3 C8061-01 0.1 Dark current ID C8062-01 1000 C8061-01 Photo response non-uniformity *3 PRNU C8062-01 *2: Including the circuit gain. *3: Measured at 50 % of the saturated output charge. Except for the start pixel and the last pixel. Max. 3 4000 ±5 ±10 Unit µm µm µm µm pC V/pC pA/pixel pA/pixel % % ■ Specifications for temperature controller [Unless otherwise noted, Ta=25 °C, C8061-01: Ts=-10 °C, VD=+5 V, VA+=+15 V, VA-=-15 V, VD2=+5 V, Vp=+5 V, VF=+12 V C8062-01: Ts=-20 °C, VD=+5 V, VA+=+15 V, VA-=-15 V, VD2=+6 V, Vp=+6 V, VF=+12 V] Parameter *4 Symbol Min. Typ. Max. Unit -11 -10 -9 °C Cooling temperature Ts -21 -20 -19 °C Temperature control range -0.1 +0.1 °C ∆Ts 7 W Power dissipation of peltier C8061-01 Pp element C8062-01 11 W Cool down time to preset temperature to 5 min. Setting temperature for overheat protection *5 To +45 °C *4: Other functions include error display, automatic power off, and detection of electrical oepns and shorts by the thermosensor. *5: Temperature at back side of housing. (between housing and fin) C8061-01 C8062-01 3 InGaAs multichannel detector head C8061/C8062-01 ■ Spectral response (Typ.) 1.5 PHOTO SENSITIVITY (A/W) T=25 ˚C T= -10 ˚C (G9208-256W: T= -20 ˚C) G9208-256W G9211 TO G9214 SERIES 1.0 0.5 0 0.5 2.0 1.5 1.0 2.5 3.0 WAVELENGTH (µm) KMIRB0022EA ■ Equivalent Circuit 1 PIXEL Cf=10 pF Cf=0.5 pF SHIFT REGISTER OFFSET COMPENSATION CDS VIDEO PHOTODIODE AD-TRIG TIMING GENERATOR Vdd INP Vss CLK RESET Vref EXTERNAL INPUT KMIRC0010EB 4 InGaAs multichannel detector head C8061/C8062-01 ■ Block diagram 1 (C8061/C8062-01) TE+ VP *1 P. GND VD2 *1 D. GND TE- THERM THERM THERMO-ELECTRIC COOLER VF (+12 V) LED TEMPERATURE CONTROLLER F. GND Temp Monitor Cooling control InGaAs IMAGE SENSOR INP Vref Vdd G9201-256S Vss G9203-256S G9211-256S G9213-256S G9205-256W G9206-256W CLK G9207-256W RESET G9208-256W Cf SELECT AD-TRIG VD1 (+5 V) D. GND VA1+ (+15 V) VA1- (-15 V) A. GND TH. H VOLTAGE REGULATOR START CLK TIMING GENERATOR Cf SEL EOS TRIGGER AMPLIFIER Video DATA VIDEO BUFFER AMPLIFIER MUX & AMPLIFIER AMPLIFIER DC CLAMP *1: +5 V (C8061-01), +6 V (C8062-01) KACCC0193EB ■ Block diagram 2 (C8061-01) TE+ VP (+5 V) P. GND VD2 (+5 V) D. GND TE- THERM THERM VF (+12 V) LED THERMO-ELECTRIC COOLER TEMPERATURE CONTROLLER F. GND Temp Monitor Cooling control InGaAs IMAGE SENSOR INP Vref G9202-512S Vdd G9204-512S Vss G9212-512S G9214-512S VD1 (+5 V) D. GND VA1+ (+15 V) VA1- (-15 V) A. GND TH. H VOLTAGE REGULATOR START CLK CLK-ODD, CLK-EVEN RESET-ODD, RESET-EVEN Cf SELECT AD-TRIG-ODD, AD-TRIG-EVEN TIMING GENERATOR Cf SEL EOS TRIGGER AMPLIFIER Video-ODD DATA VIDEO Video-EVEN BUFFER AMPLIFIER MUX & AMPLIFIER AMPLIFIER DC CLAMP KACCC0194EB 5 C8061/C8062-01 InGaAs multichannel detector head ■ Timing chart 1 (256 pixels) START CLK 2 clocks 8 clocks CLOCK RESET Video EOS TRIGGER DATA VALID 8 × (N-1) clocks 10 clocks ch 1 ch 2 ch 3 ch 4 ch (N-3) ch (N-2) ch (N-1) ch N ch 1 ch 2 ch 3 ch 4 ch (N-3) ch (N-2) ch (N-1) ch N START CLK INTEGRATION PERIOD CLOCK RESET Video EOS TRIGGER DATA VALID ch 1 ch 2 ch 3 ch 1 ch 2 ch 3 Note: N is the number of pixels (N=256) KACCC0195EA ■ Timing chart 2 (512 pixels) START CLK 2 clocks CLOCK-ODD RESET-ODD VIDED-ODD AD-TRIG-ODD CLOCK-EVEN RESET-EVEN VIDED-EVEN AD-TRIG-EVEN 8 clocks 8 × (N-1) clocks ch 1 ch (N-3) ch 3 ch 2 ch 4 10 clocks ch (N-1) ch (N-2) ch N EOS TRIGGER DATA VALID START CLK ch 1 ch 2 ch 3 ch 4 ch (N-3) ch (N-2) ch (N-1) ch N INTEGRATION PERIOD CLOCK-ODD RESET-ODD ch 1 VIDED-ODD AD-TRIG-ODD CLOCK-EVEN RESET-EVEN VIDED-EVEN AD-TRIG-EVEN ch 3 ch 2 EOS TRIGGER DATA VALID ch 1 ch 2 ch 3 Note: N is the number of pixels (N=512) KACCC0196EA 6 InGaAs multichannel detector head C8061/C8062-01 ■ Pin assignment of “signal I/O” connector 15-pin D-sub connector 8 7 15 6 14 5 13 4 12 3 11 2 10 1 9 KACCC0069EA Pin No. Terminal name Description Digital Input signal used to select conversion gain of charge amplifier in InGaAs image sensor. HCMOS compatible 1 Cf SEL High level or left open: Low gain (0.3 V/pc) Low level: High gain (6 V/pc) Analog video output 2 Data video * Positive polarity (Typ. 10 V) 3 VA1+ (+15 V) Analog power supply 4 VA1- (-15 V) Analog power supply 5 VD1 (+5 V) Digital power supply Digital input signal for initializing the circuit 6 Start HCMOS compatible. Positive logic Digital input signal for operating the circuit 7 CLK HCMOS compatible Rising edge operation Digital input signal for indicating end-of-scan of the image sensor 8 EOS HCMOS compatible Negative logic 9 A. GND Analog ground 10 A. GND Analog ground 11 NC No Connection 12 D. GND Digital ground 13 D. GND Digital ground 14 D. GND Digital ground Digital output signal for A/D conversion 15 Trigger HCMOS compatible Positive logic * Depending on the individual sensor to install, some channels might have a dark output lower than ground potential so use a bipolar A/D converter. 7 InGaAs multichannel detector head C8061/C8062-01 ■ Pin assignment of “TE control I/O” connector 9-pin D-sub connector 5 4 9 3 8 2 7 1 6 KACCC0075EA Pin No. 1 2 Description Power supply. Analog output signal of the temperature of the InGaAs image sensor. Digital input signal for starting to cool down. HCMOS compatible. 3 Cooling control H-level or left open : cooling L-level : stand-by 4 Vp (+6V) Power supply for the thermoelectric cooler in the InGaAs image sensor. 5 VF (+12 V) Power supply for cooling fan. 6 D. GND Ground. 7 D. GND Ground. 8 P. GND Power supply return of the thermoelectric cooler mounted in the InGaAs image sensor. 9 F. GND Ground return for cooling fan. Note: Available for using same power supply (+6 V) for “VD2” and “VP”. Caution: Do not connect “VD2” and “VP” together on the backside of the 9-sub D-sub connector. These may be connected (shorted) at the power supply end, not 9-pin D-sub connector. 8 Terminal name VD2 (+6V) Temp Monitor InGaAs multichannel detector head C8061/C8062-01 ■ Dimensional outlines (unit: mm) 35.0 C8061-01 34.0 2.05 0.5 FOCAL PLANE 77.0 11.0 82.0 60.0 50.0 80.0 62.0 TE Control I/O 90.0 100.0 Signal I/O FOCAL PLANE 50.0 (4 ×) M3 DEPTH 4 KACCA0089EA C8062-01 65.0 75.4 34.0 2.25 0.5 FOCAL PLANE 81.0 Signal I/O FOCAL PLANE 88.4 50.0 60.0 80.0 TE Control I/O 90.0 100.0 50.0 (4 ×) M3 DEPTH 4 KACCA0090EA 9 InGaAs multichannel detector head C8061/C8062-01 ■ Connection Example TE Controller POWER SUPPLY VF (+12 V) F. GND VP * P.GND VD2 * D. GND 5 9 4 8 3 7 6 CONTROLLER Cooling Control D. GND 2 1 I/O SIGNAL PULSE GENERATOR CLK D. GND Start D. GND POWER SUPPLY 15 14 13 VD1 (+5 V) D. GND VA+ (+15 V) VA- (-15 V) A. GND CONTROLLER Cf SEL D. GND S/H or A/D Analog Input A. GND S/H Input D. GND 12 11 10 9 8 7 6 5 4 3 2 1 OSCILLOSCOPE CH1 GND Ext.Trig GND * C8061-01: +5 V, C8062-01: +6 V KACCC0197EB Multichannel detector head controller C7557 When connected to a HAMAMATSU multichannel detector head and a personal computer, C7557 allows easy control of the detector head and data acquisition by using dedicated software that comes with the unit. Suitable multichannel detector head C7020/-02, C7021/-02, C7025/-02, C7040, C7041, C7043, C7044, C7180, C7181, C8061-01, C8062-01, C10150, C10151 ■ Accessories · SCSI terminator · Fuse (2.5 A) · Detector head connection cables · AC cable · Software (Compatible OS: Windows 98/ME *) · Operation manual * This software may be run on Windows 2000/NT/XP with a simple task. For information on how to do this, please consult with our sales office. 10 InGaAs multichannel detector head C8061/C8062-01 ■ Connection SHUTTER *1 TIMING PULSE Trig. POWER DEDICATED CABLE (WITH C7557) SIGNAL I/O SCSI *2 CABLE TE CONTROL I/O IMAGE SENSOR + MULTICHANNEL DETECTOR HEAD C7557 PC (Windows98/ME) (INTEGRATED SCSI BOARD) *1: Shutter, etc. are not available. *2: SCSI cable and SCSI board (card) are not supplied with C7557. KACCC0077ED Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2007 Hamamatsu Photonics K.K. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Cat. No. KACC1089E04 Jan. 2007 DN 11