HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Document Title 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Memory Revision History Revision No. History 0.0 Initial Draft. 0.1 1) Correct Summary description & page.7 - The Cache feature is deleted in summary description. - Note.3 is deleted. (page.7) 2) Correct table.5 & Table.12 3) Correct TSOp1, WSOP1 Pin description - 38th pin has been changed Lockpre 4) Add Bad Block Management & System Interface using CE don’t care 5) Change TSOP1, WSOP1, FBGA package dimension & figures. - Change TSOP1, WSOP1, FBGA package mechanical data - Change TSOP1, WSOP1 package figures 0.2 1) LOCKPRE is changed to PRE. - Texts, Tables and figures are changed. 2) Change Command Set - READ A and B are changed to READ 1. - READ C is changed to READ 2. 3) Change AC, DC characterics - tRB, tCRY, tCEH and tOH are added. 4) Correct Program time (max) - before : 700us - after : 500us 5) Edit figures - Address names are changed. 6) Change AC characterics Rev 0.6 / Nov. 2005 tRP tREA Before 30 35 After 25 30 Draft Date Remark Sep. 2004 Preliminary Nov. 29. 2004 Preliminary Mar. 03. 2005 Preliminary 1 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Revision History - Continued - Revision No. History Draft Date Remark Jun. 13. 2005 Preliminary 1) Change AC Characteristics (1.8V device) tRC tRP tREH tWC tWP tWH tREA Before 50 25 15 50 25 15 30 After 60 40 20 60 40 20 40 2) Change AC Parameter 0.3 tCRY(3.3V) tCRY(1.8V) tOH Before 50+tr(R/B#) 50+tr(R/B#) 15 After 60+tr(R/B#) 60+tr(R/B#) 10 3) Add Read ID Table 4) Edit Automatic Read at Power On & Power On/Off Timing - Texts & Figure are Changed. 5) Insert the Marking Information. 6) Change 128Mb Package Type. - FBGA package is deleted. - WSOP package is changed to USOP package. - Figure & dimension are changed. 0.4 1) Delete the 1.8V device’s features. 2) Change AC Conditions table 3) Add tWW parameter ( tWW = 100ns, min) - Texts & Figures are added. - tWW is added in AC timing characteristics table. 4) Edit Copy Back Program operation step 5) Edit System Interface Using CE don’t care Figures. 6) Correct Address Cycle Map. 1) Correct PKG dimension (TSOP, USOP PKG) Jul. 26. 2005 CP 0.5 0.6 Before 0.050 After 0.100 1) Correct USOP figure. Rev 0.6 / Nov. 2005 Sep. 02. 2005 Nov. 07. 2005 2 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash FEATURES SUMMARY HIGH DENSITY NAND FLASH MEMORIES - Cost effective solutions for mass storage applications NAND INTERFACE - x8 or x16 bus width. - Multiplexed Address/ Data ELECTRONIC SIGNATURE - Manufacturer Code - Device Code - Pinout compatibility for all densities SUPPLY VOLTAGE - 3.3V device: VCC = 2.7 to 3.6V STATUS REGISTER : HY27USXX281A Memory Cell Array = (512+16) Bytes x 32 Pages x 1,024 Blocks = (256+8) Words x 32 pages x 1,024 Blocks CHIP ENABLE DON'T CARE OPTION - Simple interface with microcontroller AUTOMATIC PAGE 0 READ AT POWER-UP OPTION - Boot from NAND support - Automatic Memory Download SERIAL NUMBER OPTION HARDWARE DATA PROTECTION - Program/Erase locked during Power transitions PAGE SIZE - x8 device : (512 + 16 spare) Bytes : HY27US08281A - x16 device: (256 + 8 spare) Words : HY27US16281A BLOCK SIZE - x8 device: (16K + 512 spare) Bytes - x16 device: (8K + 256 spare) Words PAGE READ / PROGRAM - Random access: 10us (max.) - Sequential access: 3.3V device: 50ns (min.) - Page program time: 200us (typ.) DATA INTEGRITY - 100,000 Program/Erase cycles - 10 years Data Retention PACKAGE - HY27US(08/16)281A-T(P) : 48-Pin TSOP1 (12 x 20 x 1.2 mm) - HY27US(08/16)281A-T (Lead) - HY27US(08/16)281A-TP (Lead Free) - HY27US(08/16)281A-S(P) : 48-Pin USOP1 (12 x 17 x 0.65 mm) - HY27US(08/16)281A-S (Lead) - HY27US(08/16)281A-SP (Lead Free) COPY BACK PROGRAM MODE - Fast page copy without external buffering FAST BLOCK ERASE - Block erase time: 2ms (Typ.) Rev 0.6 / Nov. 2005 3 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 1. SUMMARY DESCRIPTION The HYNIX HY27US(08/16)281A series is a 16Mx8bit with spare 4G bit capacity. The device is offered in 1.8V Vcc Power Supply and in 3.3V Vcc Power Supply. Its NAND cell provides the most cost-effective solution for the solid state mass storage market. The memory is divided into blocks that can be erased independently so it is possible to preserve valid data while old data is erased. The device contains 1024 blocks, composed by 32 pages consisting in two NAND structures of 16 series connected Flash cells. A program operation allows to write the 512-byte page in typical 200us and an erase operation can be performed in typical 2ms on a 16K-byte(X8 device) block. Data in the page mode can be read out at 50ns cycle time per byte. The I/O pins serve as the ports for address and data input/output as well as command input. This interface allows a reduced pin count and easy migration towards different densities, without any rearrangement of footprint. Commands, Data and Addresses are synchronously introduced using CE#, WE#, ALE and CLE input pin. The on-chip Program/Erase Controller automates all program and erase functions including pulse repetition, where required, and internal verification and margining of data. The modifying can be locked using the WP# input pin. The output pin RB# (open drain buffer) signals the status of the device during each operation. In a system with multiple memories the RB# pins can be connected all together to provide a global status signal. Even the write-intensive systems can take advantage of the HY27US(08/16)281A extended reliability of 100K program/ erase cycles by providing ECC (Error Correcting Code) with real time mapping-out algorithm. Optionally the chip could be offered with the CE# don’t care function. This option allows the direct download of the code from the NAND Flash memory device by a microcontroller, since the CE# transitions do not stop the read operation. The copy back function allows the optimization of defective blocks management: when a page program operation fails the data can be directly programmed in another page inside the same array section without the time consuming serial data insertion phase. This device includes also extra features like OTP/Unique ID area, Block Lock mechanism, Automatic Read at Power Up, Read ID2 extension. The Hynix HY27US(08/16)281A series is available in 48 - TSOP1 12 x 20 mm, 48 - USOP1 12 x 17 mm. 1.1 Product List PART NUMBER ORIZATION HY27US08281A x8 HY27US16281A x16 Rev 0.6 / Nov. 2005 VCC RANGE PACKAGE 2.7V - 3.6 Volt 48TSOP1/48USOP1 4 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 9&& &( ,2a,2 ,2a,2[2QO\ :( 5% 5( $/( &/( :3 35( 966 Figure1: Logic Diagram IO15 - IO8 Data Input / Outputs (x16 Only) IO7 - IO0 Data Input / Outputs CLE Command latch enable ALE Address latch enable CE# Chip Enable RE# Read Enable WE# Write Enable WP# Write Protect RB# Ready / Busy Vcc Power Supply Vss Ground NC No Connection PRE Power-On Read Enable, Lock Unlock Table 1: Signal Names Rev 0.6 / Nov. 2005 5 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 1& 1& 1& 1& 1& 1& 5% 5( &( 1& 1& 9FF 9VV 1& 1& &/( $/( :( :3 1& 1& 1& 1& 1& 1$1')ODVK 7623 [ 1& 1& 1& 1& ,2 ,2 ,2 ,2 1& 1& 35( 9FF 9VV 1& 1& 1& ,2 ,2 ,2 ,2 1& 1& 1& 1& 1& 1& 1& 1& 1& 1& 5% 5( &( 1& 1& 9FF 9VV 1& 1& &/( $/( :( :3 1& 1& 1& 1& 1& 1$1')ODVK 7623 [ 9VV ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 1& 35( 9FF 1& 1& 1& ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 9VV Figure 2. 48TSOP1 Contactions, x8 and x16 Device 1& 1& 1& 1& 1& 1& 5% 5( &( 1& 1& 9FF 9VV 1& 1& &/( $/( :( :3 1& 1& 1& 1& 1& 1$1')ODVK 8623 [ 1& 1& 1& 1& ,2 ,2 ,2 ,2 1& 1& 35( 9FF 9VV 1& 1& 1& ,2 ,2 ,2 ,2 1& 1& 1& 1& 1& 1& 1& 1& 1& 1& 5% 5( &( 1& 1& 9FF 9VV 1& 1& &/( $/( :( :3 1& 1& 1& 1& 1& 1$1')ODVK 8623 [ 9VV ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 1& 35( 9FF 1& 1& 1& ,2 ,2 ,2 ,2 ,2 ,2 ,2 ,2 9VV Figure 3. 48USOP1 Contactions, x8 and x16 Device Rev 0.6 / Nov. 2005 6 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 1.2 PIN DESCRIPTION Pin Name IO0-IO7 IO8-IO15(1) CLE ALE CE# WE# RE# WP# RB# VCC VSS NC PRE Description DATA INPUTS/OUTPUTS The IO pins allow to input command, address and data and to output data during read / program operations. The inputs are latched on the rising edge of Write Enable (WE#). The I/O buffer float to High-Z when the device is deselected or the outputs are disabled. COMMAND LATCH ENABLE This input activates the latching of the IO inputs inside the Address Register on the Rising edge of Write Enable (WE#). ADDRESS LATCH ENABLE This input activates the latching of the IO inputs inside the Command Register on the Rising edge of Write Enable (WE#). CHIP ENABLE This input controls the selection of the device. When the device is busy CE# low does not deselect the memory. WRITE ENABLE This input acts as clock to latch Command, Address and Data. The IO inputs are latched on the rise edge of WE#. READ ENABLE The RE# input is the serial data-out control, and when active drives the data onto the I/O bus. Data is valid tREA after the falling edge of RE# which also increments the internal column address counter by one. WRITE PROTECT The WP# pin, when Low, provides an Hardware protection against undesired modify (program / erase) operations. READY BUSY The Ready/Busy output is an Open Drain pin that signals the state of the memory. SUPPLY VOLTAGE The VCC supplies the power for all the operations (Read, Write, Erase). GROUND NO CONNECTION To Enable and disable the Lock mechanism and Power On Auto Read. When PRE is a logic high, Block Lock mode and Power-On Auto-Read mode are enabled, and when PRE is a logic low, Block Lock mode and Power-On Auto-Read mode are disabled. Power-On Auto-Read mode is available only on 3.3V device. Not using LOCK MECHANISM & POWER-ON AUTO-READ, connect it Vss or leave it N.C. Table 2: Pin Description NOTE: 1. For x16 version only 2. A 0.1uF capacitor should be connected between the Vcc Supply Voltage pin and the Vss Ground pin to decouple the current surges from the power supply. The PCB track widths must be sufficient to carry the currents required during program and erase operations. Rev 0.6 / Nov. 2005 7 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash IO0 IO1 IO2 IO3 IO4 IO5 IO6 IO7 1st Cycle A0 A1 A2 A3 A4 A5 A6 A7 2nd Cycle A9 A10 A11 A12 A13 A14 A15 A16 3rd Cycle A17 A18 A19 A20 A21 A22 A23 L(1) Table 3: Address Cycle Map(x8) NOTE: 1. L must be set to Low. 2. A8 is set to LOW or High by the 00h or 01h Command. IO0 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8-IO15 1st Cycle A0 A1 A2 A3 A4 A5 A6 A7 L(1) 2nd Cycle A9 A10 A11 A12 A13 A14 A15 A16 L(1) 3rd Cycle A17 A18 A19 A20 A21 A22 A23 L(1) L(1) Table 4: Address Cycle Map(x16) NOTE: 1. L must be set to Low. FUNCTION 1st CYCLE 2nd CYCLE 3rd CYCLE READ 1 00h/01h - - READ 2 50h - - READ ID 90h - - RESET FFh - - PAGE PROGRAM 80h 10h - COPY BACK PGM 00h 8Ah (10h) BLOCK ERASE 60h D0h - READ STATUS REGISTER 70h - - EXTRA AREA EXIT 06h LOCK BLOCK 2Ah LOCK TIGHT 2Ch UNLOCK (start area) 23h UNLOCK (end area) 24h READ LOCK STATUS 7Ah 4th CYCLE Acceptable command during busy Yes Yes Table 5: Command Set Rev 0.6 / Nov. 2005 8 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash CLE ALE CE# WE# RE# WP# H L L Rising H X L H L Rising H X H L L Rising H H L H L Rising H H L L L Rising H H Data Input L (1) H Falling X Sequential Read and Data Output L L MODE Read Mode Write Mode Command Input Address Input(3 cycles) Command Input Address Input(3 cycles) L L L H H X During Read (Busy) X X X X X H During Program (Busy) X X X X X H During Erase (Busy) X X X X X L Write Protect X X H X X 0V/Vcc Stand By Table 6: Mode Selection NOTE: 1. With the CE# don’t care option CE# high during latency time does not stop the read operation Rev 0.6 / Nov. 2005 9 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 2. BUS OPERATION There are six standard bus operations that control the device. These are Command Input, Address Input, Data Input, Data Output, Write Protect, and Standby. Typically glitches less than 5 ns on Chip Enable, Write Enable and Read Enable are ignored by the memory and do not affect bus operations. 2.1 Command Input. Command Input bus operation is used to give a command to the memory device. Command are accepted with Chip Enable low, Command Latch Enable High, Address Latch Enable low and Read Enable High and latched on the rising edge of Write Enable. Moreover for commands that starts a modifying operation (write/erase) the Write Protect pin must be high. See figure 5 and table 12 for details of the timings requirements. Command codes are always applied on IO7:0, disregarding the bus configuration (X8/X16). 2.2 Address Input. Address Input bus operation allows the insertion of the memory address. Three cycles are required to input the addresses for the 128Mbit devices. Addresses are accepted with Chip Enable low, Address Latch Enable High, Command Latch Enable low and Read Enable high and latched on the rising edge of Write Enable. Moreover for commands that starts a modify operation (write/erase) the Write Protect pin must be high. See figure 6 and table 10 for details of the timings requirements. Addresses are always applied on IO7:0, disregarding the bus configuration (X8/X16). In addition, addresses over the addressable space (A23 for 128Mbit) are disregarded even if the user sets them during command insertion. 2.3 Data Input. Data Input bus operation allows to feed to the device the data to be programmed. The data insertion is serially and timed by the Write Enable cycles. Data are accepted only with Chip Enable low, Address Latch Enable low, Command Latch Enable low, Read Enable High, and Write Protect High and latched on the rising edge of Write Enable. See figure 7 and table 12 for details of the timings requirements. 2.4 Data Output. Data Output bus operation allows to read data from the memory array and to check the status register content, the lock status and the ID data. Data can be serially shifted out toggling the Read Enable pin with Chip Enable low, Write Enable High, Address Latch Enable low, and Command Latch Enable low. See figures 8 to 12 and table 12 for details of the timings requirements. 2.5 Write Protect. Hardware Write Protection is activated when the Write Protect pin is low. In this condition modify operation do not start and the content of the memory is not altered. Write Protect pin is not latched by Write Enable to ensure the protection even during the power up. 2.6 Standby. In Standby mode the device is deselected, outputs are disabled and Power Consumption is reduced. Rev 0.6 / Nov. 2005 10 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 3. DEVICE OPERATION 3.1 Page Read. Upon initial device power up, the device defaults to Read1 mode. This operation is also initiated by writing 00h to the command register along with followed by the three address input cycles. Once the command is latched, it does not need to be written for the following page read operation. Three types of operations are available: random read, serial page read and sequential row read. The random read mode is enabled when the page address is changed. The 528 bytes (x8 device) or 264 word (x16 device) of data within the selected page are transferred to the data registers in less than access random read time tR (10us). The system controller can detect the completion of this data transfer tR (10us) by analyzing the output of RB# pin. Once the data in a page is loaded into the registers, they may be read out in 50ns cycle time by sequentially pulsing RE#. High to low transitions of the RE# clock output the data stating from the selected column address up to the last column address. After the data of last column address is clocked out, the next page is automatically selected for sequential row read. Waiting tR again allows reading the selected page. The sequential row read operation is terminated by bringing CE# high. The way the Read1 and Read2 commands work is like a pointer set to either the main area or the spare area. Writing the Read2 command user may selectively access the spare area of bytes 512 to 527. Addresses A0 to A3 set the starting address of the spare area while addresses A4 to A7 are ignored. Unless the operation is aborted, the page address is automatically incremented for sequential row Read as in Read1 operation and spare sixteen bytes of each page may be sequentially read. The Read1 command (00h/01h) is needed to move the pointer back to the main area. Figure_10 to 13 show typical sequence and timings for each read operation. Devices with automatic read of page0 at power up can be provided on request. 3.2 Page Program. The device is programmed basically on a page basis, but it does allow multiple partial page programming of a byte or consecutive bytes up to 528 (x8 device), in a single page program cycle. The number of consecutive partial page programming operations within the same page without an intervening erase operation must not exceed 1 for main array and 2 for spare array. The addressing may be done in any random order in a block. A page program cycle consists of a serial data loading period in which up to 528 bytes (x8 device) or 264 word (x16 device) of data may be loaded into the page register, followed by a non-volatile programming period where the loaded data is programmed into the appropriate cell. Serial data loading can be started from 2nd half array by moving pointer. About the pointer operation, please refer to Figure_27. The data-loading sequence begins by inputting the Serial Data Input command (80h), followed by the three address input cycles and then serial data loading. The Page Program confirm command (10h) starts the programming process. Writing 10h alone without previously entering the serial data will not initiate the programming process. The internal Program Erase Controller automatically executes the algorithms and timings necessary for program and verify, thereby freeing the system controller for other tasks. Once the program process starts, the Read Status Register command may be entered, with RE# and CE# low, to read the status register. The system controller can detect the completion of a program cycle by monitoring the RB# output, or the Status bit (I/O 6) of the Status Register. Only the Read Status command and Reset command are valid while programming is in progress. When the Page Program is complete, the Write Status Bit (I/O 0) may be checked Figure_14. The internal write verify detects only errors for "1"s that are not successfully programmed to "0"s. The command register remains in Read Status command mode until another valid command is written to the command register. Rev 0.6 / Nov. 2005 11 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 3.3 Block Erase. The Erase operation is done on a block (16K Byte) basis. It consists of an Erase Setup command (60h), a Block address loading and an Erase Confirm Command (D0h). The Erase Confirm command (D0h) following the block address loading initiates the internal erasing process. This two-step sequence of setup followed by execution command ensures that memory contents are not accidentally erased due to external noise conditions. The block address loading is accomplished in two to three cycles depending on the device density. Only block addresses (A14 to A23) are needed while A9 to A13 is ignored. At the rising edge of WE# after the erase confirm command input, the internal Program Erase Controller handles erase and erase-verify. When the erase operation is completed, the Write Status Bit (I/O 0) may be checked. Figure_16 details the sequence. 3.4 Copy-Back Program. The copy-back program is provided to quickly and efficiently rewrite data stored in one page within the plane to another page within the same plane without using an external memory. Since the time-consuming sequential-reading and its reloading cycles are removed, the system performance is improved. The benefit is especially obvious when a portion of a block is updated and the rest of the block also need to be copied to the newly assigned free block. The operation for performing a copy-back program is a sequential execution of page-read without burst-reading cycle and copying-program with the address of destination page. A normal read operation with "00h" command and the address of the source page moves the whole 528byte data into the internal buffer. As soon as the device returns to Ready state, Page-Copy Data-input command (8Ah) with the address cycles of destination page followed may be written. The Program Confirm command (10h) is not needed to actually begin the programming operation. For backward-compatibility, issuing Program Confirm command during copy-back does not affect correct device operation. Copy-Back Program operation is allowed only within the same memory plane. Once the Copy-Back Program is finished, any additional partial page programming into the copied pages is prohibited before erase. Plane address must be the same between source and target page "When there is a program-failure at Copy-Back operation, error is reported by pass/fail status. But, if Copy-Back operations are accumulated over time, bit error due to charge loss is not checked by external error detection/correction scheme. For this reason, two bit error correction is recommended for the use of Copy-Back operation." Figure 15 shows the command sequence for the copy-back operation. The Copy Back Program operation requires three steps: - 1. The source page must be read using the Read A command (one bus write cycle to setup the command and then 3 bus cycles to input the cource page address.) This operation copies all 264 Words/ 528 Bytes from the page into the page Buffer. - 2. When the device reutrns to the ready state (Ready/Busy High), the second bus write cycle of the command is given with the 3cycles to input the target page address. A23 must be the same for the Source and Target Pages. - 3. Then the confirm command is issued to start the P/E/R Controller. Rev 0.6 / Nov. 2005 12 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 3.5 Read Status Register. The device contains a Status Register which may be read to find out whether read, program or erase operation is completed, and whether the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs the content of the Status Register to the I/O pins on the falling edge of CE# or RE#, whichever occurs last. This two line control allows the system to poll the progress of each device in multiple memory connections even when RB# pins are common-wired. RE# or CE# does not need to be toggled for updated status. Refer to table 13 for specific Status Register definitions. The command register remains in Status Read mode until further commands are issued to it. Therefore, if the status register is read during a random read cycle, a read command (00h or 50h) should be given before sequential page read cycle. 3.6 Read ID. The device contains a product identification mode, initiated by writing 90h to the command register, followed by an address input of 00h. Two read cycles sequentially output the manufacturer code (ADh), the device code. The command register remains in Read ID mode until further commands are issued to it. Figure 17 shows the operation sequence, while tables 17 explain the byte meaning. 3.7 Reset. The device offers a reset feature, executed by writing FFh to the command register. When the device is in Busy state during random read, program or erase mode, the reset operation will abort these operations. The contents of memory cells being altered are no longer valid, as the data will be partially programmed or erased. The command register is cleared to wait for the next command, and the Status Register is cleared to value E0h when WP# is high. Refer to table 12 for device status after reset operation. If the device is already in reset state a new reset command will not be accepted by the command register. The RB# pin transitions to low for tRST after the Reset command is written. Refer to figure 23. Rev 0.6 / Nov. 2005 13 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 4. OTHER FEATURES 4.1 Data Protection & Power On/Off Sequence The device is designed to offer protection from any involuntary program/erase during power-transitions. An internal voltage detector disables all functions whenever Vcc is below about 2.0V (3.3V device). WP# pin provides hardware protection and is recommended to be kept at VIL during power-up and power-down. A recovery time of minimum 10us is required before internal circuit gets ready for any command sequences as shown in Figure 24. The two-step command sequence for program/erase provides additional software protection. 4.2 Ready/Busy. The device has a Ready/Busy output that provides method of indicating the completion of a page program, erase, copy-back, cache program and random read completion. The RB# pin is normally high and goes to low when the device is busy (after a reset, read, program, erase operation). It returns to high when the internal controller has finished the operation. The pin is an open-drain driver thereby allowing two or more RB# outputs to be Or-tied. Because pull-up resistor value is related to tr(RB#) and current drain during busy (Ibusy), an appropriate value can be obtained with the following reference chart (Fig 25). Its value can be determined by the following guidance. 4.3 Lock Block Feature In high state of PRE pin, Block lock mode and Power on Auto read are enabled, otherwise it is regarded as NAND Flash without PRE pin. Block Lock mode is enabled while PRE pin state is high, which is to offer protection features for NAND Flash data. The Block Lock mode is divided into Unlock, Lock, Lock-tight operation. Consecutive blocks protects data allows those blocks to be locked or lock-tighten with no latency. This block lock scheme offers two levels of protection. The first allows software control (command input method) of block locking that is useful for frequently changed data blocks, while the second requires hardware control (WP# low pulse input method) before locking can be changed that is useful for protecting infrequently changed code blocks. The followings summarized the locking functionality. - All blocks are in a locked state on power-up. Unlock sequence can unlock the locked blocks. - The Lock-tight command locks blocks and prevents from being unlocked. Lock-tight state can be returned to lock state only by Hardware control(WP low pulse input). 1. Block lock operation 1) Lock - Command Sequence: Lock block Command (2Ah). See Fig. 18. - All blocks default to locked by power-up and Hardware control (WP# low pulse input) - Partial block lock is not available; Lock block operation is based on all block unit - Unlocked blocks can be locked by using the Lock block command, and a lock block’s status can be changed to unlock or lock-tight using the appropriate commands - On the program or erase operation in Locked or Lock-tighten block, Busy state holds 1~10us(tLBSY) Rev 0.6 / Nov. 2005 14 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 2) Unlock - Command Sequence: Unlock block Command (23h) + Start block address + Command (24h) + End block address. See Fig. 19. - Unlocked blocks can be programmed or erased. - An unlocked block’s status can be changed to the locked or lock-tighten state using the appropriate sequence of commands. - Only one consecutive area can be released to unlock state from lock state; Unlocking multi area is not available. - Start block address must be nearer to the logical LSB (Least Significant Bit) than End block address. - One block is selected for unlocking block when Start block address is same as End block address. 3) Lock-tight - Command Sequence: Lock-tight block Command (2Ch). See Fig. 20. - Lock-tighten blocks offer the user an additional level of write protection beyond that of a regular lock block. A block that is lock-tighten can’t have its state changed by software control, only by hardware control (WP# low pulse input); Unlocking multi area is not available - Only locked blocks can be lock-tighten by lock-tight command. - On the program or erase operation in Locked or Lock-tighten block, Busy state holds 1~10us(tLBSY) 4) Lock Block Boundaries after Unlock Command issuing - If Start Block address = 0000h and End Block Address = FFFFh , the device is all unlocked - If Start Block address = End Block Address = FFFFh , the device is all locked except for the last Block - If Start Block address = End Block Address = 0000h , the device is all locked except for the first Block 2. Block lock Status Read Block Lock Status can be read on a block basis to find out whether designated block is available to be programmed or erased. After writing 7Ah command to the command register and block address to be checked, a read cycle outputs the content of the Block Lock Status Register to the I/O pins on the falling edge of CE# or RE#, whichever occurs last. RE# or CE# does not need to be toggled for updated status. Block Lock Status Read is prohibited while the device is busy state. Refer to table 16 for specific Status Register definitions. The command register remains in Block Lock Status Read mode until further commands are issued to it. In high state of PRE pin, write protection status can be checked by Block Lock Status Read (7Ah) while in low state by Status Read (70h). 4.4 Power-On Auto-Read The device is designed to offer automatic reading of the first page without command and address input sequence during power-on. An internal voltage detector enables auto-page read functions when Vcc reaches about 1.8V. PRE pin controls activation of auto- page read function. Auto-page read function is enabled only when PRE pin is logic high state. Serial access may be done after power-on without latency. Power-On Auto Read mode is available only on 3.3V device. Rev 0.6 / Nov. 2005 15 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Parameter Symbol Min Valid Block Number NVB 1004 Typ Max Unit 1024 Blocks Table 6: Valid Blocks Number Symbol Parameter Ambient Operating Temperature (Commercial Temperature Range) Value 3.3V Unit 0 to 70 ℃ Ambient Operating Temperature (Extended Temperature Range) -25 to 85 ℃ Ambient Operating Temperature (Industrial Temperature Range) -40 to 85 ℃ TBIAS Temperature Under Bias -50 to 125 ℃ TSTG Storage Temperature -65 to 150 ℃ VIO(2) Input or Output Voltage -0.6 to 4.6 V Supply Voltage -0.6 to 4.6 V TA Vcc Table 7: Absolute maximum ratings NOTE: 1. Except for the rating “Operating Temperature Range”, stresses above those listed in the Table “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. 2. Minimum Voltage may undershoot to -2V during transition and for less than 20ns during transitions. Rev 0.6 / Nov. 2005 16 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash $a$ $''5(66 5(*,67(5 &2817(5 352*5$0 (5$6( &21752//(5 +9*(1(5$7,21 35( $/( &/( :( &( :3 5( ; 0ELW0ELW 1$1')ODVK 0(025<$55$< ' ( & 2 ' ( 5 &200$1' ,17(5)$&( /2*,& 3$*(%8))(5 &200$1' 5(*,67(5 <'(&2'(5 '$7$ 5(*,67(5 %8))(56 ,2 Figure 4: Block Diagram Rev 0.6 / Nov. 2005 17 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Parameter Symbol Test Conditions Sequential Read ICC1 Program Erase 3.3Volt Unit Min Typ Max tRC=50ns CE#=VIL, IOUT=0mA - 10 20 mA ICC2 - - 10 20 mA ICC3 - - 10 20 mA Stand-by Current (TTL) ICC4 CE#=VIH, PRE=WP#=0V/Vcc - 1 mA Stand-by Current (CMOS) ICC5 CE#=Vcc-0.2, PRE=WP#=0V/Vcc - 10 50 uA Input Leakage Current ILI VIN=0 to Vcc (max) - - ± 10 uA Output Leakage Current ILO VOUT=0 to Vcc (max) - - ± 10 uA Input High Voltage VIH - 2 - Vcc+0.3 V Input Low Voltage VIL - -0.3 - 0.8 V Output High Voltage Level VOH IOH=-100uA - - - V IOH=-400uA 2.4 - - V Output Low Voltage Level VOL IOL=100uA - - - V IOL=2.1mA - - 0.4 V Output Low Current (RB#) IOL (RB#) VOL=0.2V - - - mA VOL=0.4V 8 10 - mA Operating Current Table 8: DC and Operating Characteristics Value Parameter 3.3Volt Input Pulse Levels 0.4V to 2.4V Input Rise and Fall Times 5ns Input and Output Timing Levels 1.5V Output Load (2.7V - 3.3V) 1 TTL GATE and CL=50pF Output Load (3.0V - 3.6V) 1 TTL GATE and CL=100pF Table 9: AC Conditions Rev 0.6 / Nov. 2005 18 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Item Symbol Test Condition Min Max Unit Input / Output Capacitance CI/O VIL=0V - 10 pF Input Capacitance CIN VIN=0V - 10 pF Table 10: Pin Capacitance (TA=25C, F=1.0MHz) Parameter Symbol Min Typ Max Unit Program Time tPROG - 200 500 us Dummy Busy Time for the Lock or Lock-tight Block tLBSY - 5 10 us Main Array NOP - - 1 Cycles Spare Array NOP - - 2 Cycles tBERS - 2 3 ms Number of partial Program Cycles in the same page Block Erase Time Table 11: Program / Erase Characteristics Rev 0.6 / Nov. 2005 19 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Parameter 3.3Volt Symbol Min Unit Max CLE Setup time tCLS 0 ns CLE Hold time tCLH 10 ns CE# setup time tCS 0 ns CE# hold time tCH 10 ns WE# pulse width tWP 25(1) ns ALE setup time tALS 0 ns ALE hold time tALH 10 ns Data setup time tDS 20 ns Data hold time tDH 10 ns Write Cycle time tWC 50 ns WE# High hold time tWH 15 ns 10 us Data Transfer from Cell to register tR ALE to RE# Delay tAR 10 ns CLE to RE# Delay tCLR 10 ns Ready to RE# Low tRR 20 ns RE# Pulse Width tRP 25 WE# High to Busy tWB Read Cycle Time tRC RE# Access Time tREA 30 ns RE# High to Output High Z tRHZ 30 ns CE# High to Output High Z tCHZ 20 ns RE# or CE# high to Output hold tOH 10 ns RE# High Hold Time tREH 15 ns tIR 0 Output High Z to RE# low CE# Access Time tCEA WE# High to RE# low tWHR ns 100 50 ns ns ns 45 60 ns ns Last RE High to busy (at sequential read) tRB 100 ns CE# High to Ready (in case of interception by CE# at read) tCRY 60+tr(R/B#)(4) ns CE# High Hold Time (at the last serial read)(3) Device Resetting Time (Read / Program / Erase) Write Protection time tCEH 100 tRST (5) tWW ns 5/10/500(2) 100 us ns Table 12: AC Timing Characteristics NOTE: 1. If tCS is less than 10ns tWP must be minimum 35ns, otherwise, tWP may be minimum 25ns. 2. If Reset Command (FFh) is written at Ready state, the device goes into Busy for maximum 5us 3. To break the sequential read cycle, CE# must be held for longer time than tCEH. 4. The time to Ready depends on the value of the pull-up resistor tied R/B# pin.ting time. 5. Program / Erase Enable Operation : tWP# high to tWE# High. Program / Erase Disable Operation : tWP# Low to tWE# High. Rev 0.6 / Nov. 2005 20 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash IO Pagae Program Block Erase Read CODING 0 Pass / Fail Pass / Fail NA Pass: ‘0’ Fail: ‘1’ 1 NA NA NA Pass: ‘0’ Fail: ‘1’ (Only for Cache Program, else Don’t care) 2 NA NA NA - 3 NA NA NA - 4 NA NA NA - 5 Ready/Busy Ready/Busy Ready/Busy Active: ‘0’ Idle: ‘1’ 6 Ready/Busy Ready/Busy Ready/Busy Busy: ‘0’ Ready’: ‘1’ 7 Write Protect Write Protect Write Protect Protected: ‘0’ Not Protected: ‘1’ Table 13: Status Register Coding DEVICE IDENTIFIER BYTE DESCRIPTION 1st Manufacturer Code 2nd Device Identifier Table 14: Device Identifier Coding Part Number Voltage Bus Width Manufacture Code Device Code HY27US08281A 3.3V x8 ADh 73h HY27US16281A 3.3V x16 ADh 53h Table 15: Read ID Data Table Rev 0.6 / Nov. 2005 21 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Table 16: Lock Status Code &/( W&/6 W&/+ W&6 W&+ &( W:3 :( W$/6 W$/+ $/( W'6 ,2a W'+ &RPPDQG Figure 5: Command Latch Cycle Rev 0.6 / Nov. 2005 22 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash W&/6 &/( W&6 W:& W:& &( W:3 W:3 W:3 W:+ :( W$/+ W$/6 W:+ W$/6 W$/+ W$/6 W$/+ $/( W'6 ,2a W'+ VW$GG W'6 W'+ QG$GG W'6 W'+ UG$GG Figure 6: Address Latch Cycle Rev 0.6 / Nov. 2005 23 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash W&/+ &/( W&+ &( W$/6 W:& $/( W:3 W:3 :( W:3 W:+ W:+ W'6 ,2[ W'+ W'6 ',1 W'+ W'6 ',1 W'+ ',1ILQDO Figure 7. Input Data Latch Cycle tCEA CE tREA tREH tRP tCHZ* tREA tREA tOH RE tRHZ tRHZ* tOH I/Ox Dout tRR Dout Dout tRC R/B Notes : Transition is measured ±200mV from steady state voltage with load. This parameter is sampled and not 100% tested. Figure 8: Sequential Out Cycle after Read (CLE=L, WE#=H, ALE=L) Rev 0.6 / Nov. 2005 24 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash W&/5 &/( W&/6 W&/+ W&6 &( W&+ W:3 :( W&($ W&+= W:+5 5( W'+ W'6 ,2 W5($ W,5 W5+= 6WDWXV2XWSXW K Figure 9: Status Read Cycle &/( W&(+ &( W&+= W:& :( W:% W&5< W$5 $/( W5+= W5 W5& 5( W53 ,2a KRUK 5% &RODGG 5RZDGG &ROXPQ $GGUHVV 3DJH5RZ$GGUHVV 'RXW1 5RZDGG 'RXW1 'RXW1 'RXW W5% %XV\ Figure 10: Read1 Operation (Read One Page) Rev 0.6 / Nov. 2005 25 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash &/( &( :( W&+= W:% W$5 $/( W5 W5& 5( W53 ,2a KRUK &RODGG &ROXPQ $GGUHVV 5RZDGG 5RZDGG 'RXW1 'RXW1 'RXW1 5RZ$GGUHVV 5% %XV\ Figure 11: Read1 Operation intercepted by CE# &/( &( :( W5 W:% $/( W$5 W55 5( ,2a K 5% &RODGG 5RZDGG 0$GGUHVV $$9DOLG$GGUHVV $$'RQW¶FDUH 'RXW 0 5RZDGG 'RXW 6HOHFWHG 5RZ 6WDUW $GGUHVV0 Figure 12: Read2 Operation (Read One Page) Rev 0.6 / Nov. 2005 26 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash &/( &( :( $/( 5( ,2a K 'RXW 1 &RODGG 5RZDGG 5RZDGG 'RXW 1 'RXW 'RXW 'RXW 'RXW 5HDG\ 5% %XV\ 0 %XV\ 0 1 2XWSXW 2XWSXW Figure 13: Sequential Row Read Operation Within a Block Rev 0.6 / Nov. 2005 27 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash &/( &( W:& W:& W:& :( W:% W352* $/( 5( ,2[ K 6HULDO'DWD ,QSXW&RPPDQG &RO$GG 5RZ$GG 5RZ$GG &ROXPQ $GGUHVV 5RZ $GGUHVV 'LQ 1 'LQ 0 XSWR%\WH 6HULDO,QSXW K 3URJUDP &RPPDQG K ,2R 5HDG6WDWXV &RPPDQG 5% ,2R 6XFFHVVIXO3URJUDP ,2R (UURULQ3URJUDP Figure 14: Page Program Operation Rev 0.6 / Nov. 2005 28 Rev 0.6 / Nov. 2005 5% ,2a 5( $/( :( &( &/( K W:& &ROPQ $GGUHVV 5RZ$GGUHVV &RODGG 5RZDGG 5RZDGG W:% %XV\ W5 KZULWHF\FOHQRPRUH ,2 (UURULQ3URJUDP %XV\ ,2 6XFFHVVIXO3URJUDP 5HDG6WDWXV &RPPDQG &ROPQ $GGUHVV 5RZ$GGUHVV ,2 K &RODGG 5RZDGG 5RZDGG &RS\%DFN'DWD ,QSXW&RPPDQG $K W352* HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Figure 15 : Copy Back Program 29 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash &/( &( W:& :( W:% W%(56 $/( 5( ,2a K 5RZDGG 5RZDGG 'K K ,2 3DJH5RZ$GGUHVV 5% %86< $XWR%ORFN(UDVH6HWXS&RPPDQG 5HDG6WDWXV &RPPDQG (UDVH&RPPDQG ,2 6XFFHVVIXO(UDVH ,2 (UURULQ(UDVH Figure 16: Block Erase Operation (Erase One Block) &/( &( :( W$5 $/( 5( W5($ K K 5HDG,'&RPPDQG $GGUHVVF\FOH ,2a $'K K 0DNHU&RGH 'HYLFH&RGH Figure 17: Read ID Operation Rev 0.6 / Nov. 2005 30 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash :3 &/( &( :( ,2[ $K /RFN&RPPDQG Figure 18: Lock Command :3 &/( &( :( $/( ,2[ K 8QRFN&RPPDQG $GG K 6WDUW%ORFN$GGUHVVF\FOHV $GG 8QORFN&RPPDQG $GG $GG (QG%ORFN$GGUHVVF\FOHV Figure 19: Unlock Command Sequence Rev 0.6 / Nov. 2005 31 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash :3 &/( &( :( ,2[ &K /RFNWLJKW&RPPDQG Figure 20: Lock Tight Command :3 &/( &( :( $/( W:+5 5( ,2[ $K 5HDG%ORFN/RFN VWDWXV&RPPDQG $GG $GG %ORFN$GGUHVVF\FOH 'RXW %ORFN/RFN6WDWXV Figure 21: Lock Status Read Timing Rev 0.6 / Nov. 2005 32 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 9 9FF :( &( $/( &/( W5 5% 35( 5( 'DWD ,2[ 'DWD 'DWD /DVW 'DWD 'DWD2XWSXW Figure 22: Automatic Read at Power On :( $/( &/( 5( ,2 ))K W567 5% Figure 23: Reset Operation Rev 0.6 / Nov. 2005 33 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 9FF 97+ W :3 :( XV Figure 24: Power On/Off Timing VTH = 2.5 Volt for 3.3 Volt Supply devices Rev 0.6 / Nov. 2005 34 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash 5S LEXV\ 9FF 5HDG\ 9FF 5% RSHQGUDLQRXWSXW 9 9 %XV\ WI WU *1' 'HYLFH )LJ5SYVWUWI5SYVLEXV\ #9FF 97D &&/ S) LEXV\ Q Q Q P P WI N N N N LEXV\>$@ WUWI>V@ P 5SRKP 5SYDOXHJXLGHQFH 5SPLQ 9FF0D[92/0D[ ,2/,/ 9 P$,/ ZKHUH,/LVWKHVXPRIWKHLQSXWFXUUQWVRIDOOGHYLFHVWLHGWRWKH5%SLQ 5SPD[LVGHWHUPLQHGE\PD[LPXPSHUPLVVLEOHOLPLWRIWU Figure 25: Ready/Busy Pin electrical specifications Rev 0.6 / Nov. 2005 35 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Figure 26: Lock/Unlock FSM Flow Cart ['HYLFHV ['HYLFHV $UHD$ K $UHD% K $UHD& K $UHD$ K $UHD& K %\WHV %\WHV %\WHV %\WHV %\WHV $ % & $ & 3DJH%XIIHU 3DJH%XIIHU 3RLQWHU KK 3RLQWHU KKK Figure 27: Pointer operations Rev 0.6 / Nov. 2005 36 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash $5($$ ,2 K K $GGUHVV ,QSXWV 'DWD,QSXW K K K $GGUHVV ,QSXWV 'DWD,QSXW K $UHDV$%&FDQEHSURJUDPPHGGHSHQGLQJRQKRZPXFKGDWDLVLQSXW6XEVHTXHQWKFRPPDQGVFDQEHRPLWWHG $5($% ,2 K K $GGUHVV ,QSXWV 'DWD,QSXW K K K $GGUHVV ,QSXWV 'DWD,QSXW K $UHDV%&FDQEHSURJUDPPHGGHSHQGLQJRQKRZPXFKGDWDLVLQSXW7KHKFRPPDQGPXVWEHUHLVVXHGEHIRUHHDFKSURJUDP $5($& ,2 K K $GGUHVV ,QSXWV 'DWD,QSXW K K K $GGUHVV ,QSXWV 'DWD,QSXW K 2QO\$UHDV&FDQEHSURJUDPPHG6XEVHTXHQWKFRPPDQGFDQEHRPLWWHG Figure 28: Pointer Operations for porgramming Rev 0.6 / Nov. 2005 37 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash System Interface Using CE don’t care To simplify system interface, CE may be deasserted during data loading or sequential data-reading as shown below. So, it is possible to connect NAND Flash to a microprocessor. The only function that was removed from standard NAND Flash to make CE don’t care read operation was disabling of the automatic sequential read function. jsl jlGNT jl ~l hsl pVv _W zGhUOZj P kGp kGp XW Figure 29: Program Operation with CE don’t-care. &/( ,IVHTXHQWLDOURZUHDGHQDEOHG &(PXVWEHKHOGORZGXULQJW5 &(GRQ¶WFDUH &( 5( $/( 5% W5 :( ,2[ K 6WDUW$GG&\FOH K 'DWD2XWSXWVHTXHQWLDO Figure 30: Read Operation with CE don’t-care. Rev 0.6 / Nov. 2005 38 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Bad Block Management Devices with Bad Blocks have the same quality level and the same AC and DC characteristics as devices where all the blocks are valid. A Bad Block does not affect the performance of valid blocks because it is isolated from the bit line and common source line by a select transistor. The devices are supplied with all the locations inside valid blocks erased(FFh).The Bad Block Information is written prior to shipping. Any block where the 6th Byte/ 1st Word in the spare area of the 1st or 2nd page (if the 1st page is Bad) does not contain FFh is a Bad Block. The Bad Block Information must be read before any erase is attempted as the Bad Block Information may be erased. For the system to be able to recognize the Bad Blocks based on the original information it is recommended to create a Bad Block table following the flowchart shown in Figure 31. The 1st block, which is placed on 00h block address is guaranteed to be a valid block. Block Replacement Over the lifetime of the device additional Bad Blocks may develop. In this case the block has to be replaced by copying the data to a valid block. These additional Bad Blocks can be identified as attempts to program or erase them will give errors in the Status Register. As the failure of a page program operation does not affect the data in other pages in the same block, the block can be replaced by re-programming the current data and copying the rest of the replaced block to an available valid block.The Copy Back Program command can be used to copy the data to a valid block. See the “Copy Back Program” section for more details. Refer to Table 17 for the recommended procedure to follow if an error occurs during an operation. Operation Recommended Procedure Erase Block Replacement Program Block Replacement or ECC Read ECC Table 17: Block Failure 67$57 %ORFN$GGUHVV %ORFN ,QFUHPHQW %ORFN$GGUHVV 'DWD ))K" 1R 8SGDWH %DG%ORFNWDEOH <HV /DVW EORFN" 1R <HV (1' Figure 31: Bad Block Management Flowchart Rev 0.6 / Nov. 2005 39 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash Write Protect Operation The Erase and Program Operations are automatically reset when WP goes Low (tWW = 100ns, min). The operations are enabled and disabled as follows (Figure 32~35) :( W :: ,2[ K K :3 5% Figure 32: Enable Programming :( W :: ,2[ K K :3 5% Figure 33: Disable Programming Rev 0.6 / Nov. 2005 40 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash :( W :: K ,2[ 'K :3 5% Figure 34: Enable Erasing :( W :: ,2[ K 'K :3 5% Figure 35: Disable Erasing Rev 0.6 / Nov. 2005 41 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash H ' $ $ % $ Į / ',( ( ( & &3 Figure 36: 48pin-TSOP1, 12 x 20mm, Package Outline millimeters Symbol Min Typ A Max 1.200 A1 0.050 0.150 A2 0.980 1.030 B 0.170 0.250 C 0.100 0.200 CP 0.100 D 11.910 12.000 12.120 E 19.900 20.000 20.100 E1 18.300 18.400 18.500 e 0.500 L 0.500 0.680 alpha 0 5 Table 18: 48pin-TSOP1, 12 x 20mm, Package Mechanical Data Rev 0.6 / Nov. 2005 42 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash $QJOH DOSKD H ' % $ $ ( & $ ' Į &3 & Figure 37. 48pin-USOP1, 12 x 17mm, Package Outline Symbol millimeters Min Typ A Max 0.650 A1 0 0.050 0.080 A2 0.470 0.520 0.570 0.230 B 0.130 0.160 C 0.065 0.100 0.175 C1 0.450 0.650 0.750 16.900 17.000 17.100 CP D 0.100 D1 11.910 12.000 12.120 E 15.300 15.400 15.500 e alpha 0.500 0 8 Table 19: 48pin-USOP1, 12 x 17mm, Package Mechanical Data Rev 0.6 / Nov. 2005 43 HY27US(08/16)281A Series 128Mbit (16Mx8bit / 8Mx16bit) NAND Flash MARKING INFORMATION - TSOP1 / USOP1 P a ck a g e TSO P1 / USOP1 M a rk in g E x a m p le H Y 2 7 x x x x x S - h y n ix : H yn ix S ym b ol - KOR : O rig in C ou n try - H Y27xSxx28xA xxxx : P a rt N u m b e r x K O R x 2 8 x A Y W W x x H Y : H yn ix 2 7 : N A N D Fla sh x : P ow e r S u pp ly : U (2 .7 V ~ 3 .6 V ) S : C la ssifica tion : S in gle Le vel C ell+ D ou ble D ie + S m a ll B lock x x : B it O rg a n iza tion : 0 8(x8 ), 1 6 (x1 6 ) 2 8 : D en sity : 1 2 8 M b it x : M o de : 1(1n C E & 1R /n B ; S e qu en tial R o w R e ad E n ab le ) 2 (1 n C E & 1 R /n B ; S e qu e n tial R ow R e ad D isab le ) A : V e rsion : 2 n d G e n era tion x : P acka ge T yp e : T (4 8 -T S O P 1 ), S (4 8 -U S O P 1 ) x : P acka g e M a te ria l : B lan k(N o rm al), P (Lea d Free ) x : O p eratin g T e m perature : C (0 ℃ ~ 7 0 ℃ ), E(-2 5℃ ~ 8 5 ℃ ) M (-3 0℃ ~ 8 5℃ ), I(-4 0 ℃ ~ 8 5℃ ) x : B ad B lo ck : B (In clu de d B a d B lock ), S (1 ~ 5 B a d B lock ), P (A ll G o o d B lo ck) - Y : Y e ar (ex: 5= year 20 0 5 , 06 = year 20 0 6 ) - w w : W o rk W ee k (e x: 1 2 = w ork w e e k 1 2 ) - x x : P roce ss C o d e N o te - C a p ita l L e tte r : Fixe d Ite m - S m a ll L e tte r : N on -fixe d Ite m Rev 0.6 / Nov. 2005 44