HY62LF16206B-DT12C 128Kx16bit full CMOS SRAM Document Title 128K x16 bit 2.5V Low Low Power Full CMOS Slow SRAM Revision History Revision No History Draft Date Remark 00 Initial Apr. 6. 2003 Final This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev.00 /Apr. 2003 Hynix Semiconductor HY62LF16206B-DT12C 128Kx16bit full CMOS SRAM DESCRIPTION FEATURES The HY62LF16206B is a high speed, super low power and 2Mbit full CMOS SRAM organized as 128K words by 16bits. The HY62LF16206B uses high performance full CMOS process technology and is designed for high speed and low power circuit technology. It is particularly well-suited for the high density low power system application. This device has a data retention mode that guarantees data to remain valid at a minimum power supply voltage of 1.2V. • Fully static operation and Tri-state output • TTL compatible inputs and outputs • Battery backup(L-part) -. 1.2V(min) data retention • Standard pin configuration -. 48-TSOP1 Product Voltage No. (V) HY62LF16206B 2.3~2.7 Notes : 1. Current value is max. Speed (ns) 120 Operation Current/Icc(mA) 1 PIN CONNECTION ROW DECODER MEMORY ARRAY 128K x 16 A16 I/O16 CONTRO L LOGIC /CS1 CS2 /OE /LB /UB /WE I/O1 DATA I/O BUFFER 48-TSOP1(Forward) A0 WRITE DRIVER A16 NC VSS IO16 IO8 IO15 IO7 IO14 IO6 IO13 IO5 VCC IO12 IO4 IO11 IO3 IO10 IO2 IO9 IO1 /OE VSS /CS1 A0 SENSE AMP 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 COLUMNDECODER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Temperature (°C) 0~70 BLOCK DIAGRAM ADD INPUT BUFFER A15 A14 A13 A12 A11 A10 A9 A8 NC NC /WE CS2 NC /UB /LB NC NC A7 A6 A5 A4 A3 A2 A1 Standby Current(uA) D 20 PIN CONNECTION Pin Name /CS1 CS2 /WE /OE /LB /UB Pin Function Chip Select 1 Chip Select 2 Write Enable Output Enable Lower Byte Control(I/O1~I/O8) Upper Byte Control(I/O9~I/O16) Pin Name I/O1~I/O16 A0~A16 Vcc Vss NC Pin Function Data Inputs / Outputs Address Inputs Power(2.3V~2.7V) Ground No Connection This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev.00 /Apr. 2003 Hynix Semiconductor HY62LF16206B-DT12C ORDERING INFORMATION Part No. HY62LF16206B-DT12C Speed 120 Power D-part Temp. 0℃ ~ 70℃ Package 48-TSOP1 ABSOLUTE MAXIMUM RATINGS (1) Symbol VIN, VOUT Vcc TA TSTG PD TSOLDER Parameter Input/Output Voltage Power Supply Operating Temperature Storage Temperature Power Dissipation Ball Soldering Temperature & Time Rating -0.3 to 3.3 -0.3 to 3.3 0 to 70 -40 to 125 1.0 260 • 10 Unit V V °C °C W °C•se c Remark Note : 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is stress rating only and the functional operation of the device under these or any other conditions above those indicated in the operation of this specification is not implied. Exposure to the absolute maximum rating conditions for extended period may affect reliability. TRUTH TABLE /CS1 CS2 /WE /OE /LB /UB H X X L L X L X H H X X X H H X X X H H L H H L L H L X X X H L X L H L L H L X X H X L H L L H L L Mode Deselected Output Disabled Read Write I/O1~I/O8 High-Z High-Z High-Z High-Z High-Z DOUT High-Z DOUT DIN High-Z DIN I/O I/O9~I/O16 High-Z High-Z High-Z High-Z High-Z High-Z DOUT DOUT High-Z DIN DIN Power Standby Active Note: 1. H=VIH, L=VIL, X=don't care(Vil or Vih) 2. UB, LB(Upper, Lower Byte enable) These active LOW inputs allow individual bytes to be written or read. When LB is LOW, data is written or read to the lower byte, I/O 1 -I/O 8. When UB is LOW, data is written or read to the upper byte, I/O 9 -I/O 16. Rev.00 /Apr. 2003 2 HY62LF16206B-DT12C RECOMMENDED DC OPERATING CONDITION Symbol Parameter Min. Vcc Supply Voltage 2.3 Vss Ground 0 VIH Input High Voltage 2.0 VIL Input Low Voltage -0.3(1) Note : 1. VIL = -1.5V for pulse width less than 30ns Typ. 2.5 0 - Max. 2.7 0 Vcc+0.3 0.4 Unit V V V V DC ELECTRICAL CHARACTERISTICS Vcc = 2.3V~2.7V, TA = 0°C to 70°C Symbol Parameter ILI Input Leakage Current ILO Output Leakage Current Icc ICC1 Operating Power Supply Current Average Operating Current ISB Standby Current (TTL Input) ISB1 Standby Current (CMOS Input) Test Condition Vss < VIN < Vcc Vss < VOUT < Vcc, /CS1 = VIH or CS2= VIL, /OE = VIH or /WE = VIL, or /UB = /LB = VIH /CS1 = VIL, CS2 = VIH, VIN = VIH or VIL, II/O = 0mA Cycle Time=Min.100% duty, /CS1 = 0.2V, CS2 = Vcc-0.2V, /WE = Vcc-0.2V, II/O = 0mA Other Inputs = Vcc-0.2V/0.2V Cycle time = 1us, /CS1 < 0.2V, CS2≥Vcc-0.2V, VIN<0.2V or Vin≥Vcc-0.2V, II/O = 0mA /CS1 = VIH, CS2 = VIL /UB = /LB = VIH, VIN = VIH or VIL /CS1 > Vcc - 0.2V or CS2 < Vss+0.2V or /UB = /LB > Vcc - 0.2V, VIN > Vcc - 0.2V or VIN < Vss + 0.2V IOL = 1.0mA IOH = -0.5mA VOL Output Low Voltage VOH Output High Voltage Notes : 1. Typical values are at Vcc = 2.5V, TA = 25°C 2. Typical values are sampled and not 100% tested Min. -1 -1 Typ. - Max. 1 1 Unit uA uA - - 1 mA - - 5 mA - - 2 mA - - 0.3 mA - - 20 uA 1.8 - 0.4 - V V CAPACITANCE (Temp = 25°C, f= 1.0MHz) Symbol Parameter Condition CIN Input Capacitance(Add, /CS, /WE, /OE) VIN = 0V COUT Output Capacitance(I/O) VI/O = 0V Note : 1. These parameters are sampled and not 100% tested Rev.00 /Apr. 2003 Max. 10 10 Unit pF pF 3 HY62LF16206B-DT12C AC CHARACTERISTICS Vcc = 2.3V~2.7V, TA = 0°C to 70°C, unless otherwise specified # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Symbol Parameter READ CYCLE tRC Read Cycle Time tAA Address Access Time tACS Chip Select Access Time tOE Output Enable to Output Valid tBA /LB, /UB Access Time tCLZ Chip Select to Output in Low Z tOLZ Output Enable to Output in Low Z tBLZ /LB, /UB Enable to Output in Low Z tCHZ Chip Deselection to Output in High Z tOHZ Out Disable to Output in High Z tBHZ /LB, /UB Disable to Output in High Z tOH Output Hold from Address Change WRITE CYCLE tWC Write Cycle Time tCW Chip Selection to End of Write tAW Address Valid to End of Write tBW /LB, /UB Valid to End of Write tAS Address Set-up Time tWP Write Pulse Width tWR Write Recovery Time tWHZ Write to Output in High Z tDW Data to Write Time Overlap tDH Data Hold from Write Time tOW Output Active from End of Write -12 Min. Max. Unit 120 10 5 10 0 0 0 10 120 120 80 120 45 45 45 - ns ns ns ns ns ns ns ns ns ns ns ns 120 100 100 100 0 85 0 0 60 0 10 35 - ns ns ns ns ns ns ns ns ns ns ns AC TEST CONDITIONS TA = 0°C to 70°C, unless otherwise specified Parameter Input Pulse Level Input Rise and Fall Time Input and Output Timing Reference Level Output Load tCLZ,tOLZ,tBLZ,tCHZ,tOHZ,tBHZ,tWHZ,tOW Others Value 0.4V to 2.2V 5ns 1.1V CL = 5pF + 1TTL Load CL = 30pF + 1TTL Load AC TEST LOADS TTL CL(1) Note : 1. Including jig and scope capacitance Rev.00 /Apr. 2003 4 HY62LF16206B-DT12C TIMING DIAGRAM READ CYCLE 1(Note 1,4) tRC ADDR tAA tOH tACS /CS1 CS2 tCHZ(3) tBA /UB ,/ LB tBHZ(3) tOE /OE Data Out tCLZ(3) High-Z tOLZ(3) tBLZ(3) tOHZ(3) Data Valid READ CYCLE 2(Note 2,3,4) tRC ADDR tAA tOH tOH Data Out Previous Data Data Valid READ CYCLE 3(Note 1,2,4) /CS1 /UB, /LB CS2 tACS tCLZ(3) Data Out tCHZ(3) Data Valid Notes: 1. A read occurs during the overlap of a low /OE, a high /WE, a low /CS1, a high CS2 and low /UB and/or /LB. 2. /OE = VIL 3. Transition is measured + 200mV from steady state voltage. This parameter is sampled and not 100% tested. 4. /CS1 in high for the standby, low for active. CS2 in low for the standby, high for active. /UB and /LB in high for the standby, low for active Rev.00 /Apr. 2003 5 HY62LF16206B-DT12C WRITE CYCLE 1 (1,4,8) (/WE Controlled) tW C ADDR tW R(2) tCW /CS1 CS2 tAW tBW /UB,/LB tW P /W E tAS Data In tDW High-Z tDH Data Valid tW HZ(3,7) tO W (5) (6) Data O ut WRITE CYCLE 2 (1,4,8) (/CS1, CS2 Controlled) tW C ADDR tCW tAS tW R (2) /CS1 tAW CS2 tBW /UB,/LB tW P /W E tDW Data In Data Out High-Z tDH Data Valid High-Z Notes: 1. A write occurs during the overlap of a low /WE, a low /CS1, a high CS2 and low /UB and/or /LB. 2. tWR is measured from the earlier of /CS, /LB, /UB, or /WE going high or CS2 going low to the end of write cycle. 3. During this period, I/O pins are in the output state so that the input signals of opposite phase to the output must not be applied. 4. If the /CS1, /LB and /UB low transition with CS2 high transition occur simultaneously with the /WE low transition or after the /WE transition, outputs remain in a high impedance state. 5. Q(data out) is the same phase with the write data of this write cycle. 6. Q(data out) is the read data of the next address. 7. Transition is measured ±200mV from steady state. This parameter is sampled and not 100% tested. 8. /CS1 in high for the standby, low for active. CS2 in low for the standby, high for active. /UB and /LB in high for the standby, low for active Rev.00 /Apr. 2003 6 HY62LF16206B-DT12C DATA RETENTION ELECTRIC CHARACTERISTIC TA = 0°C to 70°C Symbol Parameter VDR Vcc for Data Retention ICCDR Data Retention Current tCDR Chip Deselect to Data Retention Time Operating Recovery Time Test Condition /CS1 > Vcc - 0.2V or CS2 < Vss+0.2V or /UB = /LB > Vcc-0.2V, VIN > Vcc - 0.2V or VIN < Vss + 0.2V Vcc=1.5V, /CS1 > Vcc - 0.2V, CS2 < Vss+0.2V, /UB = /LB > Vcc-0.2V or VIN > Vcc - 0.2V or VIN < Vss + 0.2V See Data Retention Timing Diagram tR Notes: 1. Typical values are under the condition of TA = 25°C. 2. Typical Values are sampled and not 100% tested 3. tRC is read cycle time. Min. 1.2 Typ. - Max. 2.7 Unit V - - 20 uA 0 - - ns tRC(3) - - ns DATA RETENTION TIMING DIAGRAM 1 DATA RETENTION MODE VCC 2.3V tCDR tR VIH VDR CS1>VCC-0.2V /CS1 VSS DATA RETENTION TIMING DIAGRAM 2 DATA RETENTION MODE VCC 2.3V tCDR tR CS2 VDR 0.4V VSS Rev.00 /Apr. 2003 CS2<0.2V 7 HY62LF16206B-DT12C PACKAGE INFORMATION 48pin Thin Small Outline Package Forward #48 #1 UNIT : mm 12.0± 0.1 0.22± 0.05 #25 #24 0.145 0.5 BSC 16.4 ± 0.1 18.0 ± 0.2 1.2(max) 0.8 ± 0.2 Rev.00 /Apr. 2003 0~10˚ 8 HY62LF16206B-DT12C MARKING INSTRUCTION - Top Side Package TSOP-I (Forward) Marking Example h y n i x H Y 6 2 L y y w w p F 1 6 2 0 K O 6 B D T R E A 1 2 C Index • hynix • KOREA : Hynix Logo : Origin Country • HY62LF16206B HY 62 L F 16 20 6 B : Part Name : HYNIX : Product Group : Operating Voltage : Tech. + Classification : Organization : Density : Mode : Version • yy • ww •p : Year ( ex : 03 = year 2003, 04 = year 2004 ) : Work Week ( ex : 12 = ww12 ) : Process Code -A : 12mm X 18mm •D •T • 12 •C : Power Consumption : Package Type : Speed : Temperature Note - Capital Letter - Small Letter : Fixed Item : Non-fixed Item Rev.00 /Apr. 2003 : Slow SRAM : 2.5V(2.3V ~ 2.7V) : Full CMOS : x16 : 2M : 2CS with /UB,/LB;tCS : 3rd Generation : Low Low Power : TSOP-I : 120ns : Commercial ( 0 ~ 70 °C ) 9 HY62LF16206B-DT12C - Bottom Side Package TSOP-I (Forward) Marking Example x x x x x x x x Index • xxxxxxxx : FAB Run No. Note - Capital Letter - Small Letter : Fixed Item : Non-fixed Item Rev.00 /Apr. 2003 10