HY62UF16804B Series 512Kx16bit full CMOS SRAM Document Title 512K x16 bit 3.0V Super Low Power Full CMOS slow SRAM Revision History Revision No History 00 Initial Release 01 DC Para Change Icc 4mA à Icc1(Min) 40mA à Icc1(1us) 8mA à Isb 0.1mA à Isb1 25uA à Iccdr 12uA à Draft Date May.29.2001 Remark Preliminary Mar.20.2002 3mA 20mA 2mA 0.3mA 15uA 6uA This document is a general product description and is subject to change without notice. Hynix Semiconductor Inc does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev.01 /Mar.2002 Hynix Semiconductor HY62UF16804B Preliminary DESCRIPTION FEATURES The HY62UF16804B is a high speed, super low power and 8Mbit full CMOS SRAM organized as 512K words by 16bits. The HY62UF16804B uses high performance full CMOS process technology and is designed for high speed and low power circuit technology. It is particularly well-suited for the high density low power system application. This device has a data retention mode that guarantees data to remain valid at a minimum power supply voltage of 1.2V. • Fully static operation and Tri-state output • TTL compatible inputs and outputs • Battery backup(LL/SL-part) - 1.2V(min) data retention • Standard pin configuration - 48-fBGA Product Voltage Speed No. (V) (ns) HY62UF16804B-C 2.7~3.3 55/70/85 HY62UF16804B-I 2.7~3.3 55/70/85 Note 1. C : Commercial, I : Industrial 2. Current value is max. Operation Current/Icc(mA) 3 3 PIN CONNECTION ( Top View ) 6 A2 B IO9 /UB A3 A4 /CS IO1 C IO10 IO11 A5 A6 IO2 IO3 D Vss IO12 A17 A7 IO4 Vcc E Vcc IO13 Vss A16 IO5 Vss NC ROW DECODER A0 IO15 IO14 A14 A15 IO6 IO7 MEMORY ARRAY 256K x 16 A18 G IO16 NC A12 A13 /WE IO8 H A18 A8 A9 A10 A11 NC I/O1 I/O8 DATA I/O BUFFER A1 WRITE DRIVER /OE A0 SENSE AMP A /LB F 5 BLOCK DECODER 4 COLUMN DECODER 3 PRE DECODER 2 Temperature (°C) 0~70 -40~85 BLOCK DIAGRAM ADD INPUT BUFFER 1 Standby Current(uA) LL 15 15 I/O9 I/O16 /CS /OE /LB /UB /WE PIN DESCRIPTION Pin Name /CS /WE /OE /LB /UB Pin Function Chip Select Write Enable Output Enable Lower Byte Control(I/O1~I/O8) Upper Byte Control(I/O9~I/O16) Rev.01/Mar. 2002 Pin Name I/O1~I/O16 A0~A18 Vcc Vss NC Pin Function Data Inputs / Outputs Address Inputs Power(2.7V~3.3V) Ground No Connection 2 HY62UF16804B ORDERING INFORMATION Part No. Speed HY62UF16804B-DFC 55/70/85 HY62UF16804B-DFI 55/70/85 Note 1. C : Commercial, I : Industrial Power LL-part LL-part Package fBGA fBGA Temp. C I ABSOLUTE MAXIMUM RATINGS (1) Symbol VIN, VOUT Vcc Parameter Input/Output Voltage Power Supply TA Operating Temperature TSTG PD TSOLDER Storage Temperature Power Dissipation Ball Soldering Temperature & Time Rating -0.3 to Vcc+0.3 -0.3 to 3.6 0 to 70 -40 to 85 -55 to 150 1.0 260 • 10 Unit V V °C °C °C W °C • sec Remark HY62UF16804B-C HY62UF16804B-I Note 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is stress rating only and the functional operation of the device under these or any other conditions above those indicated in the operation of this specification is not implied. Exposure to the absolute maximum rating conditions for extended period may affect reliability. TRUTH TABLE /CS /WE /OE /LB /UB Mode H X L L L X X H H H X X H H L L X X H X L H L L H L L Deselected Deselected Output Disabled Output Disabled Read L X H L X L H L L H L Write I/O1~I/O8 High-Z High-Z High-Z High-Z DOUT High-Z DOUT DIN High-Z DIN I/O I/O9~I/O16 High-Z High-Z High-Z High-Z High-Z DOUT DOUT High-Z DIN DIN Power Standby Standby Active Active Active Active Note: 1. H=VIH, L=VIL, X=don't care(VIH or VIL) 2. UB, LB(Upper, Lower Byte enable) These active LOW inputs allow individual bytes to be written or read. When LB is LOW, data is written or read to the lower byte, I/O1 -I/O8. When UB is LOW, data is written or read to the upper byte, I/O9 -I/O16. Rev.01/Mar. 2002 2 HY62UF16804B RECOMMENDED DC OPERATING CONDITION Symbol Vcc Vss VIH VIL Parameter Supply Voltage Ground Input High Voltage Input Low Voltage Min. 2.7 0 2.2 -0.3(1) Typ. 3.0 0 - Max. 3.3 0 Vcc+0.3 0.6 Unit V V V V Note : 1. VIL = -1.5V for pulse width less than 30ns DC ELECTRICAL CHARACTERISTICS Vcc = 2.7V~3.3V, TA = 0°C to 70°C/ -40°C to 85°C Sym Parameter Test Condition ILI Input Leakage Current Vss < VIN < Vcc Vss < VOUT < Vcc, /CS = VIH or ILO Output Leakage Current /OE = VIH or /WE = VIL, /UB = /LB = VIH Operating Power Supply /CS = VIL, VIN = VIH or VIL, II/O = 0mA Icc Current Cycle Time=Min,100% duty, Average Operating II/O = 0mA, /CS = VIL,VIN = VIH or VIL Icc1 Current Cycle time = 1us, 100% duty, II/O = 0mA, /CS < 0.2V, VIN<0.2V /CS = VIH or /UB=/LB= VIH, TTL Standby Current ISB (TTL Input) VIN = VIH or VIL /CS > Vcc - 0.2V or Standby Current /UB=/LB > Vcc-0.2V, ISB1 LL (CMOS Input) VIN > Vcc-0.2V or VIN < Vss+0.2V VOL Output Low Voltage IOL = 2.1mA VOH Output High Voltage IOH = -1.0mA Min. -1 Typ. - Max. 1 Unit uA -1 - 1 uA - - 3 mA - - 20 mA - - 2 mA - - 0.3 mA - 1 15 uA 2.4 - 0.4 - V V Note : Typical values are at Vcc = 3.0V, TA = 25°C CAPACITANCE (Temp = 25°C, f = 1.0MHz) Symbol CIN COUT Parameter Input Capacitance(Add, /CS, /WE, /UB, /LB, /OE) Output Capacitance(I/O) Conditio n VIN = 0V VI/O = 0V Max. Unit 8 10 pF pF Note : These parameters are sampled and not 100% tested Rev.01/Mar. 2002 3 HY62UF16804B AC CHARACTERISTICS Vcc = 2.7V~3.3V, TA = 0°C to 70°C/ -40°C to 85°C unless otherwise specified -55 -70 # Symbol Parameter Max. Min. Max. Min. READ CYCLE 1 tRC Read Cycle Time 55 70 2 tAA Address Access Time 55 70 3 tACS Chip Select Access Time 55 70 4 tOE Output Enable to Output Valid 30 35 5 tBA /LB, /UB Access Time 55 70 6 tCLZ Chip Select to Output in Low Z 10 10 7 tOLZ Output Enable to Output in Low Z 5 5 8 tBLZ /LB, /UB Enable to Output in Low Z 10 10 9 tCHZ Chip Deselection to Output in High Z 0 30 0 30 10 tOHZ Out Disable to Output in High Z 0 30 0 30 11 tBHZ /LB, /UB Disable to Output in High Z 0 30 0 30 12 tOH Output Hold from Address Change 10 10 WRITE CYCLE 13 tWC Write Cycle Time 55 70 14 tCW Chip Selection to End of Write 50 60 15 tAW Address Valid to End of Write 50 60 16 tBW /LB, /UB Valid to End of Write 50 60 17 tAS Address Set-up Time 0 0 18 tWP Write Pulse Width 45 50 19 tWR Write Recovery Time 0 0 20 tWHZ Write to Output in High Z 0 20 0 20 21 tDW Data to Write Time Overlap 25 30 22 tDH Data Hold from Write Time 0 0 23 tOW Output Active from End of Write 5 5 - -85 Min Max. Unit 85 10 5 10 0 0 0 10 85 85 40 85 30 30 30 - ns ns ns ns ns ns ns ns ns ns ns ns 85 70 70 70 0 60 0 0 35 0 5 25 - ns ns ns ns ns ns ns ns ns ns ns AC TEST CONDITIONS TA = 0°C to 70°C / -40°C to 85°C, unless otherwise specified PARAMETER Input Pulse Level Input Rise and Fall Time Input and Output Timing Reference Level tCLZ,tOLZ,tBLZ,tCHZ,tOHZ,tBHZ,tWHZ,tOW Output Load Other Value 0.4V to 2.2V 5ns 1.5V CL = 5pF + 1TTL Load CL = 30pF + 1TTL Load AC TEST LOADS VTM = 2.8V 1029 Ohm DOUT CL(1) 1728 Ohm Note 1. Including jig and scope capacitance Rev.01/Mar. 2002 4 HY62UF16804B TIMING DIAGRAM READ CYCLE 1(Note 1,4) tRC ADDR tAA tOH tACS /CS tCHZ(3) tBA /UB ,/ LB Data Out tBHZ(3) tOE /OE High-Z tOLZ(3) tBLZ(3) tCLZ(3) tOHZ(3) Data Valid READ CYCLE 2(Note 1,2,4) tRC ADDR tAA tOH tOH Data Out Previous Data Data Valid READ CYCLE 3(Note 1,2,4) /CS /UB, /LB tACS tCLZ(3) Data Out tCHZ(3) Data Valid Notes: 1. A read occurs during the overlap of a low /OE, a high /WE, a low /CS and low /UB and /or /LB 2. /OE = VIL 3. Transition is measured + 200mV from steady state voltage. This parameter is sampled and not 100% tested. 4. /CS in high for the standby, low for active /UB and /LB in high for the standby, low for active Rev.01/Mar. 2002 5 HY62UF16804B WRITE CYCLE 1 (1,4,8) (/WE Controlled) tWC ADDR tWR(2) tCW /CS tAW tBW /UB,/LB tWP /WE tAS Data In tDW High-Z tDH Data Valid tWHZ(3,7) tOW (5) (6) Data Out WRITE CYCLE 2 (Note 1,4,8) (/CS Controlled) tWC ADDR tCW tAS tWR(2) /CS tAW tBW /UB,/LB tWP /WE tDW Data In Data Out Rev.01/Mar. 2002 High-Z tDH Data Valid High-Z 6 HY62UF16804B Notes: 1. A write occurs during the overlap of a low / WE, a low /CS and low /UB and /or /LB. 2. tWR is measured from the earlier of /CS, /LB, /UB, or /WE going high to the end of write cycle. 3. During this period, I/O pins are in the output state so that the input signals of opposite phase to the output must not be applied. 4. If the /CS, /LB and /UB low transition occur simultaneously with the /WE low transition or after the /WE transition, outputs remain in a high impedance state. 5. Q(data out) is the same phase with the write data of this write cycle. 6. Q(data out) is the read data of the next address. 7. Transition is measured +200mV from steady state. This parameter is sampled and not 100% tested. 8. /CS in high for the standby, low for active /UB and /LB in high for the standby, low for active DATA RETENTION ELECTRIC CHARACTERISTIC TA = 0°C to 70°C / -40°C to 85°C Symbol Parameter VDR Vcc for Data Retention ICCDR Data Retention Current TCDR TR Chip Deselect to Data Retention Time Operating Recovery Time Test Condition /CS > Vcc - 0.2V or /UB=/LB > Vcc-0.2V, VIN > Vcc-0.2V or VIN < Vss+0.2V Vcc=1.5V, /CS > Vcc - 0.2V or /UB=/LB > Vcc-0.2V, VIN > Vcc-0.2V or VIN < Vss+0.2V LL See Data Retention Timing Diagram Min Typ Max Unit 1.2 - 3.3 V - 1.0 6 uA 0 - - ns tRC(2) - - ns Notes: 1. Typical values are under the condition of TA = 25°C . 2. tRC is read cycle time. DATA RETENTION TIMING DIAGRAM DATA RETENTION MODE VCC 2.7V tCDR tR VIH VDR /CS or /UB & /LB /CS>Vcc-0.2V or /UB=/LB > Vcc-0.2V Vss Rev.01/Mar. 2002 7 HY62UF16804B PACKAGE INFORMATION 48ball Fine Pitch Ball Grid Array Package (F) BOTTOM VIEW TOP VIEW B A A1 CORNER INDEX AREA 6 5 4 3 2 1 A A B C D C C1 E F G C1/2 H B1/2 B1 SIDE VIEW 5 E1 E2 C E SEATING PLANE A 4 r 3 D(DIAMETER) Note Symbol A B B1 C C1 D E E1 E2 r Rev.01/Mar. 2002 Min. 5.9 8.4 0.3 0.9 0.20 - Typ. 0.75 3.75 6.0 5.25 8.5 0.35 1.0 0.76 0.25 - Max. 6.1 8.6 0.4 1.10 0.30 0.08 1. DIMENSIONING AND TOLERANCING PER ASME Y14. 5M-1994. 2. ALL DIMENSIONS ARE MILLIMETERS. 3. DIMENSION “D” IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 4. PRIMARY DATUM C(SEATING PLANE) IS DEFINED BY THE CROWN OF THE SOLDER BALLS. 5. THIS IS A CONTROLLING DIMENSION. 8 HY62UF16804B MARKING INSTRUCTION ````` Package fBGA Marking Example H Y U F c s s t x x x x 6 8 0 4 B y w w p K O R x Index • HYUF6804B : Part Name • c : Power Consumption -D • ss : Speed - 55 - 70 - 85 • t : Low Low Power : Temperature -C -I : 55ns : 70ns : 85ns : Commercial ( 0 ~ 70 °C) : Industrial ( -40 ~ 85 °C ) • y : Year (ex : 0 = year 2000, 1= year2001) • ww : Work Week ( ex : 12 = work week 12) • p : Process Code • xxxxx : Lot No. • KOR : Origin Country Note - Capital Letter - Small Letter : Fixed Item : Non-fixed Item Rev.01/Mar. 2002 9