TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com HIGH RELIABILITY SCHOTTKY RECTIFIER Qualified per MIL-PRF-19500/554 DEVICES LEVELS 1N6392 JAN JANTX JANTXV ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted) (Per Diode) Parameters / Test Conditions Symbol Value Unit Peak Repetitive Reverse Voltage VRWM 45 V Working Peak Reverse Voltage VRRM 45 V DC Blocking Voltage VR 45 V Average Forward Current, 115°C IFM 60 Note 1 Apk Peak Surge Forward Current @ tp = 8.3ms, half sinewave, Io = 0; VRM = 0 IFSM 1000 Apk Thermal Resistance, Junction to Case Rθjc 1.0 °C/W Operating Junction Temperature Tj -55°C to 175 °C Storage Temperature Tstg -55°C to 175 °C DO-5 ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) (Per Diode) Parameters / Test Conditions Symbol Forward Voltage IF = 10A, Tj = 25°C* IF = 60A, Tj = 25°C* IF = 120A, Tj = 25°C* IF = 10A, Tj = -55°C* VFM Reverse Current VR = 45V, Tj = 25°C VR = 45V, Tj = 125°C VR = 45V, Tj = 175°C IRM Junction Capacitance VR = 5V f = 1MHz Cj Min. Max. 0.51 0.68 0.82 0.69 2.0 60 200 3000 Unit V mA pF * Pulse test: Pulse width 300 µsec, Duty cycle 2% Note: 1. Derate linearly @ 1.09A/°C from Tj = Tc >115°C T4-LDS-0053 Rev. 2 (091676) Page 1 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com HIGH RELIABILITY SCHOTTKY RECTIFIER Qualified per MIL-PRF-19500/554 GRAPHS FIGURE 1 FIGURE 3 TYPICAL FORWARD CHARACTERISTICS TYPICAL JUNCTION CAPACITANCE FIGURE 4 FORWARD CURRENT DERATING FIGURE 2 TYPICAL REVERSE CHARACTERISTICS T4-LDS-0053 Rev. 2 (091676) Page 2 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com HIGH RELIABILITY SCHOTTKY RECTIFIER Qualified per MIL-PRF-19500/554 PACKAGE DIMENSIONS DO-5 C Dimensions Inches Millimeters Max Min Max Min .375 9.52 C1 .025 NOTES: 1. 2. 3. 4. 5. 6. 7. 8. Dimensions are in inches. Millimeters are given for general information only. Units must not be damaged by torque of 30 inch-pound applied to .25-28 UNF-2B nut assembled on thread. Length of incomplete or undercut threads of UD. Maximum pitch diameter of plated threads shall be basic pitch diameter .2268 inch (5.76 mm) reference (FED-STD-H28, “Screw-Thread Standards for Federal Services”). A chamfer or undercut on one or both ends of the hex portion is optional; minimum base diameter at seating plane .600 inch (15.24 mm). The angular orientation and peripheral configuration of terminal 1 is undefined, however, the major surfaces over dimensions C and C1 shall be flat and the minimum cross-sectional area from the hole to any point on the periphery shall be .0025 in2 (1.59 mm2). In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. T4-LDS-0053 Rev. 2 (091676) Ltr .080 0.64 .667 16.94 CH .450 11.43 HF .669 .688 17.00 17.47 HT1 .115 .200 2.93 5.08 HT2 .060 OAH .750 1.53 19.05 7 2.03 CD 1.00 Notes 6 25.40 SD 5 SL .422 .453 10.72 11.50 SU UD φT .220 .140 .090 .249 .175 5.59 3.56 2.28 6.32 4.44 4 Page 3 of 3