SX100U &150U 100 & 150 W att, 120 VAC Input Fully Enclosed Switching Power Supply ELECTRICAL SPECIFICATIONS All specifications are typical at nominal input, full load INPUT SPECIFICATIONS Input Voltage.................................................. 85-132 VAC Input Frequency............................................. 50/60 Hz (47-63 Hz) Input Current.................................................. 2.3A / 3.5A (typ) Inrush Current............................................... 14A /15A (typ) OUTPUT SPECIFICATIONS FEATURES REMOTE SENSE OVERVOLTAGE PROTECTION Output Voltage............................................... See chart Output Adjustment......................................... ±10% Efficiency........................................................ 82 - 87% Over-Voltage Protection................................. Shutdown 112-150% Output Over-Current Protection................................ Over 105% (Automatic Recovery) Ripple and Noise........................................... 100-200 mVp-p Hold-Up Time................................................. 20 ms Line/Load Regulation..................................... See Chart Rise Time....................................................... 300 ms max. (at 25°C nominal output/input) OVERCURRENT PROTECTION HIGHLY RELIABLE CONVECTION COOLED ON/OFF LED LIGHT ADJUSTABLE OUTPUTS 3 YEAR CONTINUOUS USE WARRANTY Leakage Current............................................ 0.5 mA max. GENERAL SPECIFICATIONS MTBF.............................................................>165,000 Hours Isolation Voltage Primary to Secondary.....................AC 2000V Primary to Case..............................AC 1500V Secondary to Case.........................AC 500V Isolation Resistance...................................... Input-Output case 100 M-Ohms min. ENVIRONMENTAL SPECIFICATIONS SAFETIES / EMI FCC-B CISPR-B VCCI-2 Operating Temperature .............................. 0˚C ~ +60˚C Derates linearly 2.5%/˚C after 50˚C Cooling............................................ Convection Temperature Coefficient.................. 0.02%/°C Humidity........................................... 20-85% RH (non-condensing) Storage Temperature....................... -20°C ~ +85°C Shock/Vibration............................... 20G (3 Directions) PHYSICAL SPECIFICATIONS Metal Enclosed - Terminal Block 50 Series MODEL OUTPUT VOLTAGE OUTPUT CURRENT EFFICIENCY (TYP) LINE REGULATION LOAD REGULATION 20.0 A 8.6 A 7.0 A 4.4 A 5 VDC 12 VDC 15 VDC 24 VDC SX100U-05S SX100U-12S SX100U-15S SX100U-24S 10 mV 10 mV 10 mV 20 mV 82% 85% 86% 87% RIPPLE NOISE 20 mV 20 mV 20 mV 30 mV 100 mVp-p 170 mVp-p 170 mVp-p 200 mVp-p SX100U LED 0.472 V. ADJ. (12) 0.748 6.299 (19max) (160 –1) I/O TERMINAL M4 +S (82.5) (88) 3.248 3.465 0 -S 3.661 (93–1) +V 2-No. 8-32UNC (MOUNTING HOLES) BOTTOM (42) H 1.654 FG N A/C IN L N 1.457 (37) 1.535 (39 –1) 4.526 (115 –0.5) 2-No. 8-32UNC (MOUNTING HOLES NOTE: (18) INCH 0.709 (25) SX100 0.984 *MOUNTING SCREWS NOT TO EXCEED MAX. PENETRATION OF 8mm. *REMOVE SHORT BAR BETWEEN (+5) AND (+V), (-S) AND (0) WHEN USE REMOTE SENSING. *TOLERANCE –1mm. *ALL DIMENSIONS IN INCH (mm) 5.590 (142 –0.5) 0.394 (10) NOTE: All specifications typical and nominal / full load and 25˚C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. 51 • No. 8-32 mounting holes standard • Dimensions in mm MODEL SX150U-05S SX150U-12S SX150U-15S SX150U-24S OUTPUT VOLTAGE OUTPUT CURRENT EFFICIENCY (TYP) LINE REGULATION LOAD REGULATION 5 VDC 12 VDC 15 VDC 24 VDC 30.0 A 12.5 A 10.0 A 6.5 A 82% 85% 86% 87% 10 mV 15 mV 15 mV 20 mV 30 mV 45 mV 45 mV 60 mV RIPPLE NOISE 100 mVp-p 170 mVp-p 170 mVp-p 200 mVp-p SX150U NOTE: All specifications typical and nominal / full load and 25˚C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. 52 • No. 8-32 mounting holes standard • Dimensions in mm