NSVS784 Dec-01 JRC SAW FILTER NSVS784 Application GSM TX Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Typical Input and Output Impedance 50Ω Nominal Center Frequency (f0) 902.5MHz Insertion Loss 890~915MHz 3.8dB max. 3.1dB Response Variation 890~915MHz 1.5dB max. 0.8dB Group Delay Variation 890~915MHz 2.5 max. 2.0 Out of Band Rejection DC~870MHz 30dB min. 45dB (Relative to 870~880MHz 6dB min. 20dB Through Level) 925~935MHz 8dB min. 13dB 935~980MHz 25dB min. 33dB 980~1200MHz 45dB min. 60dB 1200~2000MHz 10dB min. 25dB 2000~3000MHz 8dB min. 17dB (Operating Temperature Range: -30~+85ºC) Maximum Rating: (Table 2) Table2.Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -30~+85ºC -40~+95ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. Communications Equipment Division Communications Equipment Marketing Department 17-22 Akasaka 2-chome minato-ku, Tokyo. 107-0052 Japan Tel. +81 3-3584-8811 Fax. +81 3-3584-8876 http://www.jrc.co.jp/product/comm/deveice/saw/saw_top.html (Japanese) http://www.jrc.co.jp/product/comm/device/saw/saw_top_e.html (English) NSVS784 July 01 IN 50Ω 1 OUT 50Ω 6 2 SAW 5 3 4 Fig.1 Measuring circuit (1) 3.0±0.15 3.0±0.15 JOK 17 (a) (3) (b) (0.6) (0 .2 5 ) 1 .1 5 ±0 .1 5 (2) 4 2 5 (0 .6) [2x] 3 (1.80) 1 (0.75) (0.45) [4x] (0 .5 3 ) [4x ] 6 Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 0.93 1.15 Fig.3 Desirable land area (in mm) Marking (1) Manufacture’s Mark (2) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 Connection GND IN/OUT GND GND OUT/IN GND NSVS784 July 01 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -30ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. GSM RX 947.5MHz SAW FILTER NSVS784 FREQUENCY CHARACTERISTICS S21 Insertion Loss [dB] 0 0 10 1 20 2 30 3 40 4 50 5 60 6 70 7 80 8 90 9 100 847.5 947.5 Frequency [MHz] S22 S11 S22 VSWR 947.5 Frequency [MHz] 1047.5 11 10 9 8 7 6 5 4 3 2 1 847.5 947.5 Frequency [MHz] 1047.5 S21 0 10 20 Insertion Loss [dB] VSWR S11 11 10 9 8 7 6 5 4 3 2 1 847.5 10 1047.5 30 40 50 60 70 80 90 100 0 1500 Frequency [MHz] 3000