ICS ICSSSTUBF32866AZ(LF)T

ICSSSTUBF32866A
Advance Information
Integrated
Circuit
Systems, Inc.
25-Bit Configurable Registered Buffer for DDR2
Pin Configuration
Recommended Application:
•
DDR2 Memory Modules
•
Provides complete DDR DIMM solution with
ICS97ULP877
•
Ideal for DDR2 667, and 800
1
2
3
4
5
6
A
B
C
D
Product Features:
•
25-bit 1:1 or 14-bit 1:2 configurable registered buffer
with parity check functionality
•
Supports SSTL_18 JEDEC specification on data
inputs and outputs
•
Supports LVCMOS switching levels on CSR and
RESET inputs
•
Low voltage operation
VDD = 1.7V to 1.9V
•
Available in 96 BGA package
•
Drop-in replacement for ICSSSTUA32864
•
Green packages available
E
F
G
H
J
K
L
M
N
P
R
T
Functionality Truth Table
I nputs
Outputs
CK
CK
Dn,
DODT,
DCK E
Qn
QCS
QODT,
QCKE
RST
DCS
CSR
H
L
L
L
L
L
L
H
L
L
H
H
L
H
Q0
H
L
L
X
Q0
Q0
H
L
H
L
L
L
L
H
L
H
H
H
L
H
Q0
L or H
L or H
H
L
H
X
Q0
Q0
H
H
L
L
L
H
L
H
H
L
H
H
H
H
Q0
L or H
L or H
H
H
L
X
Q0
Q0
H
H
H
L
Q0
H
L
H
H
H
H
Q0
H
H
L or H
L or H
H
H
H
L or H
L or H
X
Q0
Q0
Q0
L
X or
Floating
X or
Floating
X or
Floating
X or
Floating
X or
Floating
L
L
L
96 Ball BGA
(Top View)
1240—07/17/06
ADVANCE INFORMATION documents contain information on products in the formative or design phase development. Characteristic data and other specifications are design goals.
ICS reserves the right to change or discontinue these products without notice. Third party brands and names are the property of their respective owners.
ICSSSTUBF32866A
Advance Information
Ball Assignments
25 bit 1:1 Register
A DCKE
PPO
V REF
V DD
QCKE
NC
B D2
D15
GND
GND
Q2
Q15
Q16
C D3
D16
V DD
V DD
Q3
D DODT
QERR
GND
GND
QODT
NC
E D5
D17
V DD
V DD
Q5
Q17
F D6
D18
GND
GND
Q6
Q18
G PAR_IN RST
V DD
V DD
C1
C0
H CK
DCS
GND
GND
QCS
NC
J CK
CSR
V DD
V DD
ZOH
ZOL
K D8
D19
GND
GND
Q8
Q19
L D9
M D10
D20
V DD
V DD
Q9
Q20
D21
GND
GND
Q10
Q21
N D11
D22
V DD
V DD
Q11
Q22
P D12
D23
GND
GND
Q12
Q23
R D13
D24
V DD
V DD
Q13
Q24
T D14
D25
V REF
V DD
Q14
1
2
3
4
Q25
5
6
C0 = 0, C1 = 0
14 bit 1:2 Registers
A DCKE
PPO
V REF
V DD
QCKEA
QCKEB
A D1
PPO
V REF
V DD
Q1A
B D2
NC
GND
GND
Q2A
Q2B
B D2
NC
GND
GND
Q2A
Q2B
C D3
NC
V DD
V DD
Q3A
Q3B
C D3
NC
V DD
V DD
Q3A
Q3B
D D4
E D5
QERR
GND
GND
Q4A
Q4B
NC
V DD
V DD
Q5A
Q5B
F D6
NC
D DODT
QERR
GND
GND
QODTA QODTB
E D5
NC
V DD
V DD
Q5A
F D6
NC
Q5B
GND
GND
Q6A
Q6B
G PAR_IN RST
V DD
V DD
C1
C0
H CK
DCS
GND
GND
QCSA
QCSB
J CK
CSR
V DD
V DD
ZOH
ZOL
K D8
NC
GND
GND
Q8A
Q8B
J CK
K D8
L D9
NC
V DD
V DD
Q9A
Q9B
L
G PAR_IN RST
H CK
DCS
D9
Q1B
GND
GND
Q6A
Q6B
V DD
V DD
C1
C0
GND
GND
QCSA
QCSB
CSR
V DD
V DD
ZOH
ZOL
NC
GND
GND
Q8A
Q8B
NC
V DD
V DD
Q9A
Q9B
Q10B
M D10
NC
GND
GND
Q10A
Q10B
M D10
NC
GND
GND
Q10A
N D11
NC
V DD
V DD
Q11A
Q11B
N DODT
NC
V DD
V DD
QODTA
QODTB
P D12
NC
GND
GND
Q12A
Q12B
P D12
NC
GND
GND
Q12A
Q12B
R D13
NC
V DD
V DD
Q13A
Q13B
R D13
NC
V DD
V DD
Q13A
Q13B
T D14
NC
V REF
V DD
Q14A
Q14B
T DCKE
NC
V REF
V DD
QCKEA
QCKEB
5
6
1
2
3
4
1
Register A (C0 = 0, C1 = 1)
2
3
4
5
6
Register B (C0 = 1, C1 = 1)
1240—07/17/06
2
ICSSSTUBF32866A
Advance Information
General Description
This 25-bit 1:1 or 14-bit 1:2 configurable registered buffer is designed for 1.7-V to 1.9-V VDD operation.
All clock and data inputs are compatible with the JEDEC standard for SSTL_18. The control inputs are LVCMOS. All
outputs are 1.8-V CMOS drivers that have been optimized to drive the DDR-II DIMM load. ICSSSTUBF32866A
operates from a differential clock (CK and CK). Data are registered at the crossing of CK going high, and CK going
low.
The C0 input controls the pinout configuration of the 1:2 pinout from A configuration (when low) to B configuration (when
high). The C1 input controls the pinout configuration from 25-bit 1:1 (when low) to 14-bit 1:2 (when high).
A - Pair Configuration (CO1 = 0, CI1 = 1 and CO2 = 0, CI2 = 1)
Parity that arrives one cycle after the data input to which it applies is checked on the PAR_IN of the first register.
The second register produces to PPO and QERR signals. The QERR of the first register is left floating. The valid
error information is latched on the QERR output of the second register. If an error occurs QERR is latched low for
two cycles or until Reset is low.
B - Single Configuration (CO = 0, C1 = 0)
The device supports low-power standby operation. When the reset input (RST) is low, the differential input receivers
are disabled, and undriven (floating) data, clock and reference voltage (VREF) inputs are allowed. In addition, when
RST is low all registers are reset, and all outputs are forced low. The LVCMOS RST and Cn inputs must always be
held at a valid logic high or low level. To ensure defined outputs from the register before a stable clock has been supplied,
RST must be held in the low state during power up.
In the DDR-II RDIMM application, RST is specified to be completely asynchronous with respect to CK and CK.
Therefore, no timing relationship can be guaranteed between the two. When entering reset, the register will be cleared
and the outputs will be driven low quickly, relative to the time to disable the differential input receivers. However, when
coming out of reset, the register will become active quickly, relative to the time to enable the differential input receivers.
As long as the data inputs are low, and the clock is stable during the time from the low-to-high transition of RST until
the input receivers are fully enabled, the design of the ICSSSTUBF32866A must ensure that the outputs will remain
low, thus ensuring no glitches on the output.
The device monitors both DCS and CSR inputs and will gate the Qn outputs from changing states when both DCS and
CSR inputs are high. If either DCS or CSR input is low, the Qn outputs will function normally. The RST input has priority
over the DCS and CSR control and will force the outputs low. If the DCS-control functionality is not desired, then the
CSR input can be hardwired to ground, in which case, the setup-time requirement for DCS would be the same as for
the other D data inputs. Package options include 96-ball LFBGA (MO-205CC).
Parity and Standby Functionality Truth Table
Inputs
Rst
DCS
CSR
CK
CK
H
H
H
H
H
H
H
H
L
L
L
L
H
H
H
X
X
X
X
X
L
L
H
X
↑
↑
↑
↑
↑
↑
↑
L or H
↓
↓
↓
↓
↓
↓
↓
L or H
L
X or
X or
X or
Floating Floating Floating
X or
Floating
Outputs
Sum of Inputs = H
(D1 - D25)
Even
Odd
Even
Odd
Even
Odd
X
X
X or Floating
PAR_IN
PPO
QERR
L
L
H
H
L
H
X
X
L
H
H
L
L
H
PPO0
PPO0
H
L
L
H
H
L
QERR0
QERR0
X or
Floating
L
H
1. CO = 0 and CI = 0, Data inputs are D2, D3, D5, D6, D8 - D25.
CO = 0 and CI = 1, Data inputs are D2, D3, D5, D6, D8 - D14
CO = 1 and CI = I, Data inputs are D1 - D6, D8 - D10, D12, D13
2. PAR_IN arrives one clock cycle after the data to which it applies when CO = 0.
3. PAR_IN arrives two clock cycles after the data to which it applies when CO = 1.
4. Assume QERR is high at the CK↑ and CK↓ crossing. If QERR is low it stays latched low for two
clock cycles on until Rst is low.
1240—07/17/06
3
ICSSSTUBF32866A
Advance Information
Ball Assignment
Terminal Name
GND
Description
Electrical
Characteristics
Ground
Ground input
VDD
Power supply voltage
1.8V nominal
VREF
Input reference voltage
0.9V nominal
ZOH
Reserved for future use
Input
ZOL
Reserved for future use
Input
CK
Positive master clock input
Differential input
CK
Negative master clock input
Differential input
C0, C1
Configuration control inputs
LVCMOS inputs
Asynchronous reset input - resets registers and disables VREF data and
clock differential-input receivers
LV C M O S i n p u t
RST
CSR, DCS
Chip select inputs - disables D1 - D24 outputs switching when both inputs
SSTL_18 input
are high
D1 - D25
Data input - clock in on the crossing of the rising edge of CK and the
falling edge of CK
SSTL_18 input
DODT
The outputs of this register bit will not be suspended by the DCS and
CSR control
SSTL_18 input
DCKE
The outputs of this register bit will now be suspended by the DCS and
CSR control
SSTL_18 input
Data ouputs that are suspended by the DCS and CSR control
1.8V CMOS
Q1 - Q25
QCS
Data output that will not be suspended by the DCS and CSR control
1.8V CMOS
QODT
Data output that will not be suspended by the DCS and CSR control
1.8V CMOS
QCKE
Data output that will not be suspended by the DCS and CSR control
1.8V CMOS
Par tial parity out indicates off parity of inputs D1 - D25.
1.8V CMOS
PAR_IN
PPO
Parity input arrives one clock cycle after the corresponding data input
SSTL_18 input
QERR
Output error bit-generated one clock cycle after the corresponding data
output
Open drain
output
1240—07/17/06
4
ICSSSTUBF32866A
Advance Information
Block Diagram for 1:1 mode (positive logic)
RST
CK
CK
VREF
DCKE
D
C1
QCKEA
C1
QODTA
R
DODT
D
R
DCS
1D
C1
QCSA
R
CSR
D1
0
1
1D
Q1A
C1
R
To 21 Other Channels
*Note: Disabled in 1:1 configuration
1240—07/17/06
5
Q1B*
ICSSSTUBF32866A
Advance Information
Block Diagram for 1:2 mode (positive logic)
RST
CK
CK
VREF
DCKE
1D
QCKEA
C1
DODT
R
QCKEB*
1D
QODTA
C1
DCS
R
QODTB*
1D
QCSA
C1
R
QCSB*
1D
Q1A
CSR
D1
0
1
C1
R
To 10 Other Channels
*Note: Disabled in 1:1 configuration
1240—07/17/06
6
Q1B*
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
CK
CK
G2
H1
J1
LPS0
(internal node)
D2•D3,
D5•D6,
D8-D25
V REF
22
A3, T3
D2•D3,
D5•D6,
D8•D25
CE
D
CK
Q
22
22
R
22
Q2 Q3,
Q5 Q6,
Q8 Q25
D2•D3,
D5•D6,
D8•D25
Parity
Generator
C1
G5
1
0
Q
D
1
CK
R
G1
PPO
0
Q
D
CK
R
PAR_IN
Q
D
A2
CK
R
CE
D2
QERR
C0
G6
CK
2•Bit
Counter
R
LPS1
(internal node)
0
D
Q
1
CK
R
Figure 6
Parity logic diagram for 1:1 register configuration (positive logic): C0=0, C1=0
1240—07/17/06
7
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
CK
CK
G2
H1
J1
LPS0
(internal node)
D2•D3,
D5•D6,
D8-D14
V REF
11
A3, T3
D2•D3,
D5•D6,
D8•D14
CE
D
CK
Q
11
11
R
11
11
D2•D3,
D5•D6,
D8•D14
Q2A•Q3A,
Q5A•Q6A,
Q8A•Q14A
Q2B•Q3B,
Q5B•Q6B,
Q8B•Q14B
Parity
Generator
C1
G5
1
0
D
Q
D
CK
D
Q
CK
R
PAR_IN
A2
PPO
1
R
G1
0
Q
CK
R
CE
D2
QERR
C0
G6
CK
2•Bit
Counter
R
LPS1
(internal node)
0
D
Q
1
CK
R
Figure 7 — Parity logic diagram for 1:2 register-A configuration (positive logic); C0=0, C1=1
1240—07/17/06
8
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
CK
CK
G2
H1
J1
LPS0
(internal node)
D1•D6,
D8-D13
V REF
11
A3, T3
11
D1•D6,
D8•D13
CE
D
CK
Q1A•Q6A,
Q8A•Q13A
Q
11
R
11
11
D1•D6,
D8•D13
Q1B•Q6B,
Q8B•Q13B
Parity
Generator
C1
G5
D
Q
0
1
1
0
PPO
D
CK
D
Q
CK
R
PAR_IN
A2
R
G1
Q
CK
R
CE
D2
QERR
C0
G6
CK
2•Bit
Counter
R
LPS1
(internal node)
0
D
Q
1
CK
R
Figure 8
Parity logic diagram for 1:2 register-B configuration (positive logic); CO=1, C1=1
1240—07/17/06
9
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
DCS
CSR
n
n +1
n +2
n+3
n+4
CK
CK
tact
tsu
th
D1•D25 †
tpdm , t pdmss
CK to Q
Q1•Q25
tsu
th
PAR_IN †
t pd
CK to PPO
PPO
tPHL
CK to QERR
QERR ‡
tPHL , t PLH
CK to QERR
Data to QERR Latency
H, L, or X
H or L
Figure 9 — Timing diagram for SSTU32866 used as a single device; C0=0, C1=0;
RST Switches from L to H
†
After RST is switched from low to high, all data and PAR_IN inputs signals must be set and held low for a minimum time of t
max, to avoid false error.
‡
If the data is clocked in on the n clock pulse, the QERR output signal will be generated on the n+2 clock pulse, and it will be valid on
the n+3 clock pulse.
1240—07/17/06
10
ACT
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
DCS
CSR
n
n +1
n +2
n+3
n+4
CK
CK
tsu
th
D1•D25
tpdm , t pdmss
CK to
Q1•Q25
tsu
th
PAR_IN
tpd
CK to PPO
PPO
Data to PPO Latency
tPHL or t PLH
CK to QERR
QERR †
Data to QERR Latency
Unknown input
event
Figure 10
†
Output signal is dependent on
the prior unknown input event
H or L
Timing diagram for SSTU32866 used as a single device; C0=0, C1=0;
RST being held high
If the data is clocked in on the n clock pulse, the QERR output signal will be generated on the n+2 clock pulse, and it will be valid on
the n+3 clock pulse. If an error occurs and the QERR output is driven low, it stays latched low for a minimum of two clock cycles or
until RST is driven low.
1240—07/17/06
11
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
tinact
DCS †
CSR †
CK †
CK †
D1•D25 †
tRPHL
RST to Q
Q1•Q25
PAR_IN †
tRPHL
RST to PPO
PPO
QERR
tRPLH
RST to QERR
H, L, or X
H or L
Figure 11 — Timing diagram for SSTU32866 used as a single device; C0=0, C1=0;
RST switches from H to L
†
After RST is switched from high to low, all data and clock unouts signals must be set and held at valid logic levels (not floating) for
a minimum time of tINACT max.
1240—07/17/06
12
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
DCS
CSR
n
n+1
n+2
n+3
n +4
CK
CK
tact
t su
th
D1•D14 †
tpdm , t pdmss
CK to Q
Q1•Q14
tsu
th
PAR_IN †
t pd
CK to PPO
PPO
QERR# ‡
(not used)
tPHL
CK to QERR
t PHL , t PLH
CK to QERR
Data to QERR#
Latency
H, L, or X
H or L
Figure 12 — Timing diagram for the first SSTU32866 (1:2 register-A configuration) device used in
pair; C0=0, C1=1; RST switches from L to H
†
After RST is switched from low to high, all data and PAIR_IN inputs signals must be set and held low for a minimum time of tACT
max, to avoid false error
‡
If the data is clocked in on the n clock pulse, the QERR output signal will be generated on the n+1 clock pulse, and it will be valid on
the n+2 clock pulse.
1240—07/17/06
13
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST
DCS
CSR
n
n +1
n+2
n+3
n+4
CK
CK
tsu
th
D1•D14
tpdm , t pdmss
CK to Q
Q1•Q14
tsu
th
PAR_IN
tpd
CK to PPO
PPO
tPHL or t PLH
CK to QERR
Data to PPO
Latency
QERR †
(not used)
Data to QERR
Latency
Unknown input
event
Output signal is dependent on
the prior unknown input event
H or L
Figure 13 — Timing diagram for the first SSTU32866 (1:2 register-A configuration) device used in
pair; C0=0, C1=1; RST being held high
†
If the data is clocked in on the clock pulse, the QERR output signal will be generated on the n+1 clock pulse, and it will be valid on
the n+2 clock pulse. If an error occurs and the QERR output is driven low, it stays latched low for a minimum of two clock cycles or
until RST is driven low.
1240—07/17/06
14
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST#
t inact
DCS# †
CSR# †
CK
†
CK#
†
D1•D14 †
tRPHL
RST# to Q
Q1•Q14
PAR_IN †
tRPHL
RST# to PPO
PPO
QERR#
(not used)
tRPLH
RST# to QERR#
H, L, or X
H or L
Figure 14 — Timing diagram for the first SSTU32866 (1:2 register-A configuration) device used in
pair; C0=0, C1=1; RST# switches from H to L
†
After RST# is switched from high to low, all data and clock inputs signals must be held at valid logic levels (not floating) for a
minimum time of t IN ACT max
1240—07/17/06
15
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST#
DCS#
CSR#
n
n+1
n+2
n+ 3
n +4
CK
CK#
t act
t su
th
D1•D14 †
tpdm , t pdmss
CK to Q
Q1•Q14
tsu
th
PAR_IN †‡
tpd
CK to PPO
PPO
(not used)
t PHL
CK to QERR#
t PHL , t PLH
CK to QERR#
QERR# §
Data to QERR# Latency
H, L, or X
H or L
Figure 15 — Timing diagram for the second SSTU32866 (1:2 register-B configuration) device used in
pair; C0=1, C1=1; RST# switches from L to H
†
After RST# switched from low to high, all data and PAR_IN inputs signals must be set and held low for a minimum time of t
ACT
max, to avoid false error.
‡
PAR_IN is driven from PPO of the first SSTU32866 device.
§
If the data is clocked in on the n clock pulse, the QERR# output signal will be generated on the n+2 clock pulse, and it will be valid on
the n+3 clock pulse.
1240—07/17/06
16
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST#
DCS#
CSR#
n
n+1
n+2
n+3
n+4
CK
CK#
t su
th
D1•D14
tpdm , t pdmss
CK to Q
Q1•Q14
tsu
th
PAR_IN
tpd
CK to PPO
PPO
Data to PPO
Latency
t PHL or t PLH
CK to QERR#
QERR# †
(not used)
Data to QERR#
Latency
Unknown input
event
Output signal is dependent on
the prior unknown input event
H or L
Figure 16 — Timing diagram for the second SSTU32866 (1:2 register-B cofiguration) device used in
pair; C0=1, C1=1; RST# being held high
†
PAR_IN is driven from PPO of the first SSTU32866 device
‡
If the data is clocked in on the n clock pulse, the QERR# output signal will be generated on the n+2 clock pulse, and it will be valid on
the n+3 clock pulse. If an erro occurs and the QERR# output is driven low, it stays latched low for a minimum of two clock cycles or
until RST# is driven low.
1240—07/17/06
17
ICSSSTUBF32866A
Advance Information
2. Device standard (cont'd)
RST#
t inact
DCS# †
CSR# †
CK
†
CK# †
D1•D14 †
t RPHL
RST# to Q
Q1•Q14
PAR_IN †
tRPHL
RST# to PPO
PPO
(not used)
QERR#
tRPLH
RST# to QERR#
H, L, or X
H or L
Figure 17 — Timing diagram for the second SSTU32866 (1:2 register-B configuration) device used in
pair; C0=1, C1=1; RST# switches from H to L
†
After RST# is switched from high to low, all data and clock input signals must be held at valid logic levels (not floating) for a
munimum time of t INACT max.
1240—07/17/06
18
ICSSSTUBF32866A
Advance Information
* Register Configurations
DATA INPUT:
DATA OUTPUT:
CO
CI
D2, D3, D5, D6,
D8 - D25
D2, D3, D5, D6,
D8 - D25
0
0
D2, D3, D5, D6,
D8 - D14
D2, D3, D5, D6,
D8 - D14
0
1
D1 - D6, D8 D10, D12, D13
D1 - D6, D8 D10, D12, D13
1
1
1240—07/17/06
19
ICSSSTUBF32866A
Advance Information
Absolute Maximum Ratings
Storage Temperature . . . . . . . . . . . . . . . . . . . .
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . .
Input Voltage1,2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Voltage1,2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Clamp Current . . . . . . . . . . . . . . . . . . . .
Output Clamp Current . . . . . . . . . . . . . . . . . . .
Continuous Output Current . . . . . . . . . . . . . . .
VDD or GND Current/Pin . . . . . . . . . . . . . . . .
–65°C to +150°C
-0.5V to 2.5V
-0.5V to +2.5V
-0.5V to VDD + 0.5V
±50 mA
±50mA
±50mA
±100mA
Package Thermal Impedance3
36°C
...............
Notes:
1. The input and output negative voltage
ratings may be excluded if the input
and output clamp ratings are observed.
2. This value is limited to 2.5V maximum.
3. The package thermal impedance is
calculated in accordance with
JESD 51.
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These
ratings are stress specifications only and functional operation of the device at these or any other conditions above those
listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect product reliability.
Recommended Operating Conditions
PARAMETER
VDDQ
VREF
VTT
VI
VIH (DC)
VIH (AC)
VIL (DC)
VIL (AC)
VIH
VIL
VICR
VID
IOH
IOL
TA
DESCRIPTION
I/O Supply Voltage
Reference Voltage
Termination Voltage
Input Voltage
DC Input High Voltage
AC Input High Voltage
Data Inputs
DC Input Low Voltage
AC Input Low Voltage
Input High Voltage Level
RST#
Input Low Voltage Level
Common mode Input Range
CK, CK#
Differential Input Voltage
High-Level Output Current
Low-Level Output Current
Operating Free-Air Temperature
1
MIN
TYP
1.7
1.8
0.49 x VDD 0.5 x VDD
V REF - 0.04
VREF
0
VREF + 0.125
VREF + 0.250
MAX
1.9
0.51 x V DD
VREF + 0.04
VDDQ
VREF - 0.125
VREF - 0.250
UNITS
V
0.65 x VDDQ
0.675
0.600
0
0.35 x VDDQ
1.125
-8
8
70
mA
°C
Guaranteed by design, not 100% tested in production.
Note: Rst# and Cn inputs must be helf at valid logic levels (not floating) to ensure proper device operation. The
differential inputs must not be floating unless Rst# is low.
1240—07/17/06
20
ICSSSTUBF32866A
Advance Information
Electrical Characteristics - DC
TA = 0 - 70°C; VDD = 1.8 +/-0.1V (unless otherwise stated)
SYMBOL
PARAMETERS
VIK
VOH
VOL
All Inputs
II
Standby (Static)
I DD
Operating (Static)
IDDD
Ci
CONDITIONS
I I = -18mA
I OH = -6mA
I OL = 6mA
V I = VDD or GND
RESET# = GND
V I = VIH(AC) or VIL(AC),
RESET# = V DD
RESET# = V DD,
Dynamic operating
V I = VIH(AC) or V IL(AC),
(clock only)
CLK and CLK# switching
50% duty cycle.
IO = 0
Dynamic Operating RESET# = V DD,
(per each data input) V I = VIH(AC) or V IL (AC),
CLK and CLK# switching
1:1 mode
50% duty cycle. One data
Dynamic Operating input switching at half
(per each data input) clock frequency, 50%
1:2 mode
duty cycle
V I = VREF ±350mV
Data Inputs
V ICR = 1.25V, VI(PP) = 360mV
CLK and CLK#
RESET#
V I = VDD or GND
VDD
MIN
1.7V
1.7V
1.9V
1.2
TYP
0.5
5
100
-5
1.9V
40
mA
19
µA/ clock
MHz/data
35
2.5
2
3.5
3
2.5
Output Buffer Characteristics
Output edge rates over recommended operating free-air temperature range (See figure 7)
VDD = 1.8V ± 0.1V
PARAMETER
UNIT
MIN
MAX
dV/dt_r
1
4
V/ns
dV/dt_f
1
4
V/ns
1
dV/dt_∆
1
V/ns
1. Difference between dV/dt_r (rising edge rate) and dV/dt_f (falling edge rate)
21
µA
µA
µ/clock
MHz
39
1.8V
UNITS
V
Notes:
1 - Guaranteed by design, not 100% tested in production.
1240—07/17/06
MAX
-1.2
pF
ICSSSTUBF32866A
Advance Information
Timing Requirements
(over recommended operating free-air temperature range, unless otherwise noted)
fclock
tW
tACT
tINACT
V DD = 1.8V ±0.1V
MIN
MAX
410
PARAMETERS
SYMBOL
Clock frequency
1
-
ns
Differential inputs active time (See Notes 1 and 2)
-
10
ns
-
15
ns
Differential inputs inactive time (See Notes 1 and 3)
Setup time
tsu
Setup time
tsu
Setup time
tsu
Setup time
tsu
Setup time
Hold time
DCS# before CK↑, CK#↓,
CSR# high
CSR# before CK↑, CK#↓,
DCS# high
DCS# before CK↑, CK#↓,
CSR# low
DODT, DCKE and data before
CK↑, CK#↓
tH
0.55
ns
0.55
ns
0.35
ns
0.35
ns
PAR_IN before CK↑, CK#↓
0.35
ns
DCS#, DODT, DCKE and Q
after CK↑, CK#↓
0.35
ns
0.35
ns
PAR_IN after CK↑, CK#↓
Hold time
1 - Guaranteed by design, not 100% tested in production.
2 - For data signal input slew rate of 1V/ns.
3 - For data signal input slew rate of 0.5V/ns and < 1V/ns.
4 - CLK/CLK# signal input slew rate of 1V/ns.
Switching Characteristics
(over recommended operating free-air temperature range, unless otherwise noted)
Measurement
Symbol
Parameter
MIN
MAX
Conditions
fmax
MHz
Pulse duration, CK, CK HIGH or LOW
tsu
Notes:
UNITS
Max input clock frequency
410
Propagation delay, single
CK↑ to CK#↓ QN
bit switching
Propagation delay
CK↑ to CK#↓ to PPO
t PD
Low to High propagation
CK↑ to CK#↓ to QERR#
tLH
delay
High to low propagation
tHL
CK↑ to CK#↓ to QERR#
delay
Propagation delay
tPDMSS
CK↑ to CK#↓ QN
simultaneous switching
High to low propagation
t PHL
Rst# ↓ to QN↓
delay
High to low propagation
t PHL
Rst# ↓ to PPO↓
delay
Low to High propagation
Rst# ↓ to QERR#↑
t PLH
delay
2. Guaranteed by design, not 100% tested in production.
t PDM
1240—07/17/06
22
Units
MHz
1.1
1.5
ns
0.5
1.7
ns
1.2
3
ns
1
2.4
ns
-
1.6
ns
3
ns
3
ns
3
ns
ICSSSTUBF32866A
Advance Information
VDD
DUT
TL=50Ω
•
CK Inputs
CK#
CK
RL = 1000Ω
•
TL=350p s, 50Ω
Out
Test Point
CL = 30 pF
(see Note 1)
Test Point
RL = 1000Ω
•
RL = 100Ω
•
LOAD CIRCUIT
Test Point
VCMOS
RST#
Inp ut
VDD
VDD /2
VDD/2
t in act
IDD
(see
Note 2)
VID
0V
CK
CK
t PL H
90%
t PH L
10%
VOH
Ou tput
VOLTAGE AND CURRENT WAVEFORMS
INPUTS ACTIVE AND INACTIVE TIMES
VICR
VTT
VTT
VICR
VOLTAGE WAVEFORMS – PULSE DURATION
LVCMOS
RST#
Input
VID
CK
VIH
VDD /2
VIL
VICR
t RPHL
CK
t su
Inpu t
VOL
VOLTAGE WAVEFORMS – PROPAGATION DELA TIMES
VID
tw
Inpu t
VIC R
VICR
t act
VREF
VOH
th
Ou tput
VREF
VIH
VTT
VOL
VOLTAGE WAVEFORMS – PROPAGATION DELA TIMES
VIL
VOLTAGE WAVEFORMS – SETUP AND HOLD TIMES
Figure 6 — Parameter M easurement I nfor mation (V DD = 1.8 V ± 0.1 V)
Notes: 1. CL incluces probe and jig capacitance.
2. IDD tested with clock and data inputs held at VDD or GND, and Io = 0mA.
3. All input pulses are supplied by generators having the following chareacteristics: PRR ≤10 MHz,
Zo=50Ω, input slew rate = 1 V/ns ±20% (unless otherwise specified).
4. The outputs are measured one at a time with one transition per measurement.
5. VREF = VDD/2
6. VIH = VREF + 250 mV (ac voltage levels) for differential inputs. VIH = VDD for LVCMOS input.
7. VIL = VREF - 250 mV (ac voltage levels) for differential inputs. VIL = GND for LVCMOS input.
8. VID = 600 mV
9. tPLH and tPHL are the same as tPDM.
1240—07/17/06
23
ICSSSTUBF32866A
Advance Information
VDD
DUT
RL = 50Ω
Out
Test Point
C L = 10 pF
(see Note 1)
LOAD CIRCUIT – HIGH-TO-LOW SLEW-RATE MEASUREMENT
Output
VOH
80%
20%
dv _f
VOL
dt _f
VOLTAGE WAVEFORMS – HIGH-TO-LOW SLEW-RATE MEASUREMENT
DUT
Out
Test Point
CL = 10 pF
(see Note 1)
RL = 50Ω
LOAD CIRCUIT – LOW-TO-HIGH SLEW-RATE MEASUREMENT
dt _r
dv _r
80%
VOH
20%
Output
VOL
VOLTAGE WAVEFORMS – LOW-TO-HIGH SLEW-RATE MEASUREMENT
Figure 7 - Output Slew - Rate Measurement Information (V DD = 1.8 V ± 0.1 V)
Notes: 1. CL includes probe and jig capacitance.
2. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10MHz, ZO =
50Ω, input slew rate = 1 V/ns ±20% (unless otherwise specified).
1240—07/17/06
24
ICSSSTUBF32866A
Advance Information
3 Test circuits and switching waveforms (cont’d)
3.3 Error output load circuit and voltage measurement information (VDD = 1.8 V ± 0.1 V)
All input pulses are supplied by generators having the following characteristics: PRR
Zo = 50 Ω ; input slew rate = 1 V/ns ± 20%, unless otherwise specified.
10 MHz;
VDD
DUT
RL = 1K Ω
Out
Test Point
CL = 10 pF
(see Note 1)
LOAD CIRCUIT – HIGH-TO-LOW SLEW-RATE MEASUREMENT
(1) CL includes probe and jig capacitance.
Figure 28 — Load circuit, error output measurements
LVCMOS
RST#
Input
V CC
V CC /2
0V
t PLH
V OH
Output
Waveform 2
V _ _ _ _ _ _ _
_ _0.15
__
0V
Figure 29 — Voltage waveforms, open-drain output low-to-high transition time with respect to reset input
V I(PP)
Timing
Inputs
V ICR
VICR
tPHL
Output
Waveform 1
___________
V CC /2
V CC
V OL
Figure 30 — Voltage waveforms, open-drain output high-to-low transition time with respect to clock inputs
V I(PP)
Timing
Inputs
VICR
VICR
tPHL
Output
Waveform 2
V OH
0.15 V
0V
Figure 31 — Voltage waveforms, open-drain output low-to-high transition time with respect to clock inputs
1240—07/17/06
25
ICSSSTUBF32866A
Advance Information
Test circuits and switching waveforms (cont’d)
3.4 Partial-parity-out load circuit and voltage measurement information (VDD = 1.8 V ± 0.1 V)
All input pulses are supplied by generators having the following characteristics: PRR
Zo = 50 Ω input slew rate = 1 V/ns ± 20%, unless otherwise specified.
10 MHz;
DUT
Test Point
Out
CL = 5 pF
(see Note A)
RL = 1 k Ω
(1) CL includes probe and jig capacitance.
Figure 32 — Partial-parity-out load circuit,
CK
VICR
VICR
tPLH
tPHL
Vi(p-p)
CK
VOH
VTT
OUTPUT
VOL
002aaa375
VTT = VDD /2
tPLH an tPHL are the same as tPD .
VI(PP) = 600 mV
Figure 33 — Partial-parity-out voltage waveforms; propagation delay times with respect to clock inputs
LVCMOS RST#
VIH
INPUT
VDD /2
VIL
tPHL
VOH
OUTPUT
VTT
VOL
002aaa376
VTT = VDD /2
tPLH an tPHL are the same as tPD .
VIH = VRE F + 250 mV (AC voltage levels for differential inputs. VIH = VDD for LVCMOS inputs.
VIL = VRE F - 250 mV (AC voltage levels) for differential inputs. VIL = VDD for LVCMOS inputs.
Figure 34 — Partial-parity-out voltage waveforms; propagation delay times with respect to reset input
1240—07/17/06
26
ICSSSTUBF32866A
Advance Information
C
Seating
Plane
A1
T
Numeric Designations
for Horizontal Grid
b
REF
4 3 2 1
A
B
C
D
D
Alpha Designations
for Vertical Grid
(Letters I, O, Q & S
not used)
d TYP
D1
- e - TYP
TOP VIEW
E
c
REF
h
TYP
0.12 C
- e - TYP
E1
ALL DIMENSIONS IN MILLIMETERS
----- BALL GRID ----Max.
T
e
HORIZ
VERT
TOTAL
d
Min/Max
Min/Max
13.50 Bsc
5.50 Bsc
1.20/1.40
0.80 Bsc
6
16
96
0.40/0.50
11.50 Bsc
5.00 Bsc
1.00/1.20
0.65 Bsc
6
16
96
0.35/0.45
Note: Ball grid total indicates maximum ball count for package. Lesser quantity may be used.
D
E
h
Min/Max
0.25/0.41
0.25/0.35
REF. DIMENSIONS
b
c
0.75
0.875
* Source Ref.: JEDEC Publication 95,
10-0055C
Ordering Information
ICSSSTUBF32866Az(LF)T
Example:
ICS XXXX y z (LF) T
Designation for tape and reel packaging
Lead Free, RoHS Compliant (Optional)
Package Type
H = LFBGA (standard size: 5.5 x 13.50)
HM = TFBGA (reduced size: 5.0 x 11.50)
Revision Designator (will not correlate with datasheet revision)
Device Type
1240—07/17/06
Prefix
ICS = Standard Device
27
0.75
0.875
MO-205
ICSSSTUBF32866A
Advance Information
Revision History
Rev.
0.1
Issue Date Description
6/29/2006 Initial Release
Page #
-
1240—07/17/06
28