140 MHz Filter 10 MHz Bandwidth Part Number SF0140BA03107S Integrated Circuit Systems, Inc. TYPICAL PERFORMANCE Horizontal: 4 MHz/div Vertical (from top): Magnitude Phase Deviation Group Delay Variation 10,1 10 50 dB/div deg/div ns/div SPECIFICATION Parameter Center Frequency 1 Insertion Loss 1 dB Bandwidth 3 dB Bandwidth 35 dB Bandwidth Passband Ripple 2 Phase Deviation from Linear 2 Group Delay Variation 2 Absolute Delay Ultimate Rejection (30-350 MHz) Substrate Material Temperature Coefficient of Frequency (Tc) 3 Ambient Temperature Source and Load Impedance Notes: Min 139.8 9.6 10.5 Typ 140 8.3 9.92 10.9 14.0 0.25 3 30 1.0 Max 140.2 9.5 15 1 6 100 40 YZ Lithium Niobate -94 25 50 Units MHz dB MHz MHz MHz dB deg ns us dB ppm/°C °C Ω 1. Average of lower & upper 3 dB frequencies. 2. Evaluated over 80% of the 3 dB bandwidth. 3. Typical change of filter frequency response with temperature is Δf/fref = (T-Tref)*Tc ppm. Rev X7 22-Mar-05 Page 1 of 4 Integrated Circuit Systems • Surface Acoustic Wave Products 324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456 www.icst.com QF12/3 140 MHz Filter 10 MHz Bandwidth Part Number SF0140BA03107S Integrated Circuit Systems, Inc. PACKAGE AND SUGGESTED PCB FOOTPRINT PACKAGE INFORMATION SUGGESTED PCB FOOTPRINT 15.37 13.33 ±.20 10 9 8 .89 7 ICS 11 6 6.50 ±.20 BA03107S 12 YYJJJM 2 1 8.53 2.54 2.98 5 3 4 2.54 2.59 7.62 1.98 MAX PIN CONFIGURATION 11 INPUT 12 INPUT RETURN 5 OUTPUT 6 OUTPUT RETURN GROUND ALL OTHERS .80 1 2 3 4 12 5 6 11 10 9 8 7 2.54 12X 1.4 NOTES: DIMENSIONS SHOWN ARE NOMINAL IN MILLIMETERS. ALL TOLERANCES ARE ±0.15MM EXCEPT OVERALL LENGTH AND WIDTH Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating MARKING 10 LOGO 11 8 7 ICS 6 BA03107S MARKING ESD PIN 1 9 12 5 YYJJJM 1 2 3 4 The date code consists of: YY = last two digits of year; JJJ = Julian day; M = manufacturing site code Rev X7 22-Mar-05 Page 2 of 4 Integrated Circuit Systems • Surface Acoustic Wave Products 324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456 www.icst.com QF12/3 140 MHz Filter 10 MHz Bandwidth Part Number SF0140BA03107S Integrated Circuit Systems, Inc. MATCHING CIRCUIT 11 5 1, 2,3,4,6,7,8,9,10,12 Component values in 50 Ω: (Minimum Q = 40) Ls1 = 68 nH Cp1 = 15 pF Ls2 = 100 nH Cp2 = 10 pF Notes: 1. Optimum values may differ from these when using a different fixture or board layout. The values shown here are intended as a guide only. MAXIMUM RATINGS Parameter Storage Temperature Range Maximum Input Power Level D. C. Voltage between Each Terminal Min Max -45 +85 15 15 Units ºC dBm V Rev X7 22-Mar-05 Page 3 of 4 Integrated Circuit Systems • Surface Acoustic Wave Products 324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456 www.icst.com QF12/3 140 MHz Filter 10 MHz Bandwidth Part Number SF0140BA03107S Integrated Circuit Systems, Inc. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS Parameter Qualification Conditions Life Testing High temperature bake at +85 ºC for 168 hours. MIL-STD 883, Method 1010: -40 ºC to +85 ºC, 10 cycles, 10 minutes dwell at temperature extremes MIL-STD-202, Method 201A: 10 to 55 Hz, double amplitude of 0.06” for 2 hours in each axis. MIL-STD-883, Method 2002, Test Condition B: 1500 g, 3 impacts each axis Peak temperature 240+/-5 ºC for 10 seconds. Pre-heat: 150-170 ºC for 60 to 90 seconds. Peak dwell: over 200 ºC for 23 to 26 seconds. Handling: Class 1 per MIL-STD-1686 Reflow Profile is shown at the bottom of this table. MIL-STD 883 Method 2004, Condition D 8 oz for 30 seconds. MIL-STD-883 Method 2003: 245 ºC +/-5 ºC; 95% coverage; no steam aging MIL-STD 883 Method 1014: Condition A2 and Condition C (no bomb) Class I per MIL-STD-883 Method 3015 Do not subject devices to ultrasonic cleaning, which may cause deterioration and destruction of the device. Temperature Cycling Vibration Mechanical Shock Solder Heat Resistance and Reflow Condition Lead Integrity Solderability Hermeticity ESD Classification Precautions Reflow Profile 250 TEMP (deg C) 200 150 100 50 0 0 50 100 150 200 250 300 TIME (sec) ISO 9001 Registered Rev X7 22-Mar-05 Page 4 of 4 Integrated Circuit Systems • Surface Acoustic Wave Products 324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456 www.icst.com QF12/3