Micro Networks A Division of Integrated Device Technology 140 MHz SAW Filter 16 MHz Bandwidth Part Number: SF0140BA03114S DESCRIPTION • • 140 MHz SAW bandpass filter with 16 MHz bandwidth in 13.3x6.5mm SMP. RoHS compliant. TYPICAL PERFORMANCE S11 S22 Horizontal : Frequency 5 MHz / div Vertical (from top) Magnitude Magnitude Phase Deviation Group Delay Deviation 10 1 10 200 dB/div dB/div deg/div ns/div Input and Output Impedances Frequency Span : 100-180 MHz Wide Band Response Frequency Span : 0-500 MHz Vertical Scale : 10 dB/div IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 1 of 3 140 MHz SAW Filter 16 MHz Bandwidth Part Number: SF0140BA03114S Micro Networks A Division of Integrated Device Technology SPECIFICATION Parameter Center Frequency (Fc) 1 Insertion Loss 2 1 dB Bandwidth 3 dB Bandwidth 35 dB Bandwidth Passband Ripple 3 Phase Deviation from Linear 3 Group Delay Variation 3 Absolute Delay Ultimate Rejection 4 Substrate Temperature Coefficient of Frequency Ambient Temperature System Source and Load Impedance Notes: Min 139.6 15 16 40 Typ Max 140 140.4 8.2 11 16.4 17.4 21.1 22 0.43 1 3 14 45 160 0.94 44 Lithium Niobate -90 25 50 Units MHz dB MHz MHz MHz dB p-p deg p-p ns p-p µs dB ppm/˚C ˚C Ω 1. Average of the lower and upper 3 dB frequencies. 2. Average level in the passband. 3. Evaluated over 80% of the 3dB bandwidth (i.e. FC±6.4 MHz). 4. Evaluated over the intervals 20 – 124 MHz and 156 – 280 MHz. MAXIMUM RATINGS Parameter Storage Temperature Range Input Power Level DC Voltage Between Each Terminal Min -40 Max +85 +17 15 Units ˚C dBm V MATCHING CIRCUIT 11 Input 50 Ω Source Single Ended 5 Output 50 Ω Load Single Ended 1,2,3,4,6, 7,8,9,10,12 Component values (minimum inductor Q = 45): Ls1 = 100 nH Cp1 = 33 pF Ls2 = 120 nH Cp2 = 0 pF (not used) Notes: 1. The component values shown above are those used in the Micro Networks test fixture. Optimum values may change depending on board layout. Cp2 may be a capacitor or an inductor. 2. 5% tolerance components or better are recommended. IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 2 of 3 140 MHz SAW Filter 16 MHz Bandwidth Part Number: SF0140BA03114S Micro Networks A Division of Integrated Device Technology PACKAGE OUTLINE AND RECOMMENDED PCB LAYOUT PACKAGE INFORMATION RECOMMENDED PCB FOOTPRINT 15.37 ICS .89 BA03114S YYJJJM 8.53 2.54 2.98 2.54 2.59 7.62 Pin Configuration: 11 Input 12 Input Return 5 Output 6 Output Return All Others Ground NOTE: Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating Dimensions shown are all nominal in millimetres. All tolerances are ±0.15 mm except overall length and width. ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. © 2005 All rights reserved. IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.icst.com/saw.aspx Rev X2 24-Nov-2005 Page 3 of 3