4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP Part Number: AA4040PBC/Z PRELIMINARY SPEC BLUE ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description zSINGLE COLOR. The Blue source color devices are made with InGaN Light zSUITABLE FOR ALL SMT ASSEMBLY AND Emitting Diode. SOLDER PROCESS. Static electricity and surge damage the LEDS. zAVAILABLE ON TAPE AND REEL. It is recommended to use a wrist band or anti-electrostatic zIDEAL FOR BACKLIGHTING. glove when handling the LEDs. zPACKAGE : 500PCS / REEL. All devices, equipment and machinery must be electrically zMOISTURE SENSITIVITY LEVEL : LEVEL 4. grounded. zRoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH2389 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/22/2007 DRAWN: W.J.ZHU PAGE: 1 OF 6 ERP: 1201003011 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might leads to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. SPEC NO: DSAH2389 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/22/2007 DRAWN: W.J.ZHU PAGE: 2 OF 6 ERP: 1201003011 Selection Guide Dice Part No. AA4040PBC/Z Iv (mcd) [2] @ 20mA Lens Type BLUE (InGaN) Viewing Angle [1] Min. Typ. 2θ1/2 110 280 120° WATER CLEAR Notes: 1.θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2.Luminous Intensity / Luminous Flux: +/-15% Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Blue λD [1] Dominant Wavelength Δλ1/2 Typ. Max. Units Test Conditions 458 nm IF=20mA Blue 465 nm IF=20mA Spectral Line Half-width Blue 22 nm IF=20mA C Capacitance Blue 110 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue 3.2 3.7 V IF=20mA IR Reverse Current Blue 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Blue Units Power dissipation 111 mW DC Forward Current 30 mA Peak Forward Current [1] 100 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAH2389 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/22/2007 DRAWN: W.J.ZHU PAGE: 3 OF 6 ERP: 1201003011 Blue SPEC NO: DSAH2389 APPROVED: WYNEC AA4040PBC/Z REV NO: V.2 CHECKED: Allen Liu DATE: JUN/22/2007 DRAWN: W.J.ZHU PAGE: 4 OF 6 ERP: 1201003011 AA4040PBC/Z Recommended Soldering Pattern (Units : mm; Tolerance: ±0.1) Tape Specifications (Units : mm) SPEC NO: DSAH2389 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/22/2007 DRAWN: W.J.ZHU PAGE: 5 OF 6 ERP: 1201003011 PACKING & LABEL SPECIFICATIONS SPEC NO: DSAH2389 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu AA4040PBC/Z DATE: JUN/22/2007 DRAWN: W.J.ZHU PAGE: 6 OF 6 ERP: 1201003011