5.0X6.0mm SURFACE MOUNT LED LAMP AA5060SYC/E SUPER BRIGHT YELLOW Description Features The Super Bright Yellow source color devices are made with SINGLE COLOR. SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER DH InGaAlP on GaAs substrate Light Emitting Diode. PROCESS. AVAILABLE ON TAPE AND REEL. IDEAL FOR BACKLIGHTING. PACKAGE : 500PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD0900 REV NO: V.5 DATE: MAR/14/2005 PAGE: 1 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000539 Selection Guide Part No. Dice AA5060SYC/E Iv (mcd) @ 50mA Lens Type SUPER BRIGHT YELLOW (InGaAIP) WATER CLEAR Viewing Angle Min. Typ. 2θ θ1/2 280 500 100° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Yellow λD Dominant Wavelength ∆λ1/2 Max. Units Test Conditions 592 nm IF=20mA Super Bright Yellow 590 nm IF=20mA Spectral Line Half-width Super Bright Yellow 20 nm IF=20mA C Capacitance Super Bright Yellow 33 pF VF=0V;f=1MHz VF Forward Voltage Super Bright Yellow 2.0 2.5 V IF=20mA IR Reverse Current Super Bright Yellow 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Super Bright Yellow Units Power dissipation 125 mW DC Forward Current 50 mA Peak Forward Current [1] 200 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD0900 REV NO: V.5 DATE: MAR/14/2005 PAGE: 2 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000539 Super Bright Yellow AA5060SYC/E SPEC NO: DSAD0900 REV NO: V.5 DATE: MAR/14/2005 PAGE: 3 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000539 AA5060SYC/E Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. D i g i t a l l y s i g n e d b y N I N G T I N G c n = N I N G T I N G , o = N I N G T I N G , c = C N D a t e : 2 0 0 5 . 0 3 . 1 4 1 4 : 3 0 : 0 7 + 0 8 '0 0 'R e a s o n : < n o n e > SPEC NO: DSAD0900 REV NO: V.5 DATE: MAR/14/2005 PAGE: 4 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI ERP: 1201000539